Samsung HW-D770S User manual User manual

PDF

Document

HW-D700
HW-D770S
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HW-D700_D770S_ELS_0609.indd 1
2011-06-09
5:37:07
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
voltage” inside the product that presents
a risk of electric shock or personal injury.
This symbol indicates important
instructions accompanying the product.
WARNING
• To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
• This apparatus shall always be connected to a AC outlet with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore
the mains plug shall be readily operable.
• Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
• The Mains plug is used as a disconnect device and shall stay readily operable at any time.
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated
on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of
the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer. If the fitted plug is not
suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a
suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative to cutting
off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains socket as there is
a risk of shock hazard from the bared flexible cord. Never attempt to insert bare wires directly into a mains socket. A
plug and fuse must be used at all times.
IMPORTANT
The wires in the mains lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN
= LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug,
proceed as follows:–The wire coloured BLUE must be connected to the terminal marked with the letter N or
coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH LETTER E OR
BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
2
English
HW-D700_D770S_ELS_0609.indd 2
2011-06-09
5:37:24
Precautions
• Ensure that the AC power supply in your house complies with specifications listed on the identification sticker
located on the back of your product.
• Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm).
• Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
• Do not stack anything on top of the product.
• To disconnect the product completely from the power supply, remove its plug from the wall outlet.
- If you leave the product unused for a long period of time, disconnect the plug from the wall outlet.
• During thunderstorms, disconnect the AC plug from the wall outlet. Voltage spikes caused by lightning could
damage the product.
• Do not expose the product to direct sunlight or other heat sources. This could cause the product to overheat
and malfunction.
• Protect the product from moisture, excess heat, and equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the product malfunctions.
• Your product is not intended for industrial use. It is for personal use only.
• Condensation may occur if you store your product in cold temperatures. If transporting the product during the
winter, wait approximately 2 hours until the product has reached room temperature before using.
• The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
English
HW-D700_D770S_ELS_0609.indd 3
3
2011-06-09
5:37:24
Contents
2
3
Safety Warnings
Precautions
GETTING STARTED
6
6
6
8
9
10
Accessories
Description
Front Panel
Display
Rear Panel
Remote Control
CONNECTIONS
14
16
18
19
21
22
23
24
25
26
27
29
29
Speaker Positioning
Connecting the Speakers
Connecting the Bi-AMP Speaker
Connecting External Devices/your TV via HDMI
HDMI Function
Connecting to your TV
Connecting a DVD or BD(Blu-ray) Player
Connecting a Cable, Satellite or Set-top Box
Connecting a CD Player
Connecting Using the External Amplifier (Ex. Second Room)
Connecting an iPod
Connecting the FM Antenna
Connecting AUX Components
SETUP
30
30
31
32
35
35
Before Using the AV Receiver
Home Menu
Selecting Digital/HDMI/Analogue
Setup Menu Tree
Audio Setup
Selecting a Source Device And Connection Jack
(Digital Audio In)
Setting the Speaker Size
Connection Setting For Surround Back
Setting the Speaker Listening Distance
Setting the Speaker Level
Setting the Test Tone
Setting Dolby Pro Logic Mode
Surround Setup
Setting Dolby Pro Logic IIx
Setting NEO:6 Mode
Setting EX/ES Mode
Other Settings
Audio Sync
Tone Control
MP3 Enhancer
Smart Volume
Auto Calibration Setup
DRC Setup
Dual Mono Setup
HDMI Setup
Video Convert Setup
SAFETY INFORMATION
2
6
14
30
35
37
38
39
40
41
41
41
42
42
43
43
43
44
44
44
46
46
46
47
4
English
HW-D700_D770S_ELS_0609.indd 4
2011-06-09
5:37:24
OPERATION
49
49
49
50
51
51
52
52
53
53
53
54
55
55
55
56
56
57
57
57
58
58
Using the Surround Modes
Using the S.DIRECT Button
Using the AUDIO EFFECT Button On the Front of the
Main Unit
Using the SUBWOOFER button
Listening to the Radio
To Listen in Mono/Stereo
Presetting Radio Stations
About RDS Broadcasting
Using the RDS (Radio Data System) to Receive FM
Stations
To Show the RDS Signals
PTY (Program Type) Indication and PTY-SEARCH
Function
Using an iPod
Listening to Music (iPod audio function)
Watching a Movie (iPod video function)
Convenient Functions
Sleep Timer Function
Mute Function
Adjust the Display
Reset Function
Using Headphones
Software Upgrade
59
60
Operating your TV with the Remote Control
Operating your DVD or BD Player with the Remote
Control
OTHER INFORMATION
61
62
63
64
Troubleshooting
Product Protection Function
Auto Calibration Error List
Specifications
59
61
ENGLISH
MISCELLANEOUS
•
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance.
•
An administration fee may be charged if either
a. an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual)
b. you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
•
The amount of such administration charge will be advised to you before any work or home visit is carried out.
English
HW-D700_D770S_ELS_0609.indd 5
5
2011-06-09
5:37:24
Getting Started
Accessories
Check the box for the supplied accessories listed below.
INPUT SELECT
TV SOURCE
POWER
AMP
TV
BD
DVD
TA
RDS DISPLAY
1
2
PTY-
PTY SEARCH
4
5
6
SLEEP
DIMMER
NEO:6
3
PTY+
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
MUTE
TUNING
/CH
VOL
S.DIRECT
TONE
MO/ST
TUNER MEMORY
SETUP/MENU
INFO
RETURN
BD/DVD
AV SYNC
ASC
EXIT
SAT
AUX
SUB
WOOFER
GAME/TV
CD
iPod
TUNER
CROSS
OVER
3D SOUND
Remote Control/
Batteries (AAA size)
FM antenna
User’s manual
(For Speaker cable)
iPod Dock
Toroidal Ferrite Core
ASC microphone
Description
Front Panel
1
2 3
4 5
6
7
8 9 10 11
12
13
Bi-AMP
14
6
15
16
17 18 19
20
21 22
English
HW-D700_D770S_ELS_0609.indd 6
2011-06-09
5:37:25
01
Getting Started
1
INPUT SELECT CONTROL
Used to select a source.
FM TV BD/DVD SAT GAME AUX CD IPOD AUDIO IPOD VIDEO
2
3
4
5
6
SETUP BUTTON
Displays the SETUP menu.
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
AUDIO EFFECT BUTTON
Toggles to select a surround sound mode.
3D SOUND BUTTON
Press to apply 3D Sound effect.
DISPLAY
Displays the speaker/audio input status, listening mode, etc.
7
UP(,), DOWN(.), LEFT(&lt;),
RIGHT(&gt;) BUTTONS
Used to move the cursor up, down, left or right.
Also used to select detailed options in the AUDIO EFFECT mode and to change the
tone level.
8
9
10
11
12
13
14
15
Bi-AMP INDICATOR
The indicator lights on when you turn on Bi-AMP.
ENTER BUTTON
Used to select an item in the SETUP menu.
TONE CONTROL BUTTON
Used to set the bass, treble level and tone to on/off.
ASC BUTTON
Used to select the Auto calibration mode.
MASTER VOLUME CONTROL
Adjusts the volume level.
POWER BUTTON (
Turns the receiver on/off.
)
PHONES JACK
Used to connect a set of headphones.
AUX IN JACKS
Auxiliary AV input terminals used to connect a camcorder, portable DVD player or
gaming device.
16
ASC MIC JACK
Used to connect the ASC MIC for setting up Auto calibration.
17
18
19
20
21
RETURN BUTTON
Return to the previous menu.
AV SYNC BUTTON
Used to select the Audio Delay Mode.
TUNING MODE BUTTON
Used to select the Manual or Preset mode for FM radio.
SELECT BUTTON
Used to change the radio frequency.
TUNER MEMORY BUTTON
Used to set a preset radio frequency.
22
S.DIRECT BUTTON
Used to select the S.DIRECT mode.
(Output the original signal as it is without applying the sound field effect or any
other sound effect.)
English
HW-D700_D770S_ELS_0609.indd 7
7
2011-06-09
5:37:26
Getting Started
Display
1
2
3
4
5
7
6
1
2
3
4
5
SPEAKER INDICATORS
Displays sound producing speakers.
LISTENING MODE INDICATORS
Displays the current listening mode and audio source.
TUNING INDICATORS
Displays the status of the current radio broadcast.
AUDIO INPUT INDICATORS
Displays the audio input signal type of the currently connected external audio source.
SPEAKER LEVEL INDICATOR
Displays the speaker level.
6
RADIO FREQUENCY
INDICATORS
Displays the current radio frequency range.
7
MESSAGE DISPLAY
Informs you of the status of the receiver.
8
English
HW-D700_D770S_ELS_0609.indd 8
2011-06-09
5:37:27
01
Getting Started
Rear Panel
1
2
3
4
5
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
6
1
2
3
4
5
6
7
8
9
10
11
12
13
7
8
9
10
11
12 13 14 15
16
VIDEO IN JACKS
Receives the video signal from a video player (BD/DVD, SAT, TV).
USB PORT
Can be only used for firmware upgrades.
HDMI OUT JACKS
Outputs digital video and audio signals simultaneously using an HDMI cable.
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an HDMI cable.
VIDEO OUT JACK
Outputs the video signal to a monitors(TV, Projector etc).
FM ANTENNA JACK
Connect the FM antenna.
iPod JACK
Receives the audio/video signal from an iPod.
ONLY FOR SERVICE JACK
Used for the service repair.
AUDIO IN JACKS
Receives the audio signal from a video player (BD/DVD, SAT, TV).
COMPONENT VIDEO IN JACKS
Receives the component video signal.
COMPONENT VIDEO OUT JACKS Outputs the component video signal.
OPTICAL IN JACKS (DIGITAL AUDIO IN) Receives the digital optical audio signal.
COAXIAL IN JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal.
14
LINE OUT JACKS
Outputs the analogue audio signal to the external amplifier.
The digital signal output is not supported.
15
SUBWOOFER AUDIO OUT JACKS Connect the subwoofers. (Active subwoofer only)
16
SPEAKERS OUT TERMINALS
Speaker connection terminals.
The front speaker and surround back speaker ports can be connected to a
speaker that supports bi-amplifying. For connecting to the bi-amplifier, refer
to page 18.
English
HW-D700_D770S_ELS_0609.indd 9
9
2011-06-09
5:37:27
Getting Started
Remote Control
Tour of the Remote Control
1
INPUT SELECT
TV SOURCE
POWER
20
21
2
3
4
5
AMP
TV
BD
DVD
TA
RDS DISPLAY
1
2
3
PTY-
PTY SEARCH
PTY+
4
5
6
NEO:6
SLEEP
DIMMER
7
8
9
PROLOGIC
AUDIO ASSIGN
DSP
0
6
22
23
24
25
26
7
27
28
8
29
MUTE
9
10
TUNING
/CH
VOL
S.DIRECT
11
12
TONE
MO/ST
TUNER MEMORY
32
INFO
33
34
14
16
31
SETUP/MENU
13
15
30
RETURN
EXIT
BD/DVD
SAT
GAME/TV
CD
AV SYNC
AUX
iPod
TUNER
ASC
SUB
WOOFER
35
17
10
CROSS
OVER
3D SOUND
18
36
19
37
English
HW-D700_D770S_ELS_0609.indd 10
2011-06-09
5:37:29
01
Getting Started
1
POWER BUTTON
Turns the receiver on/off.
2
TV BUTTON
To change to TV mode, press the TV button.
3
AMP BUTTON
To change to AMP mode, press the AMP button.
4
NUMBER BUTTONS
Used to select a TV channel.
5
NEO : 6 BUTTON
Select the desired NEO:6 mode.
6
PROLOGIC BUTTON
Select the desired Dolby Pro Logic audio mode.
7
SKIP BUTTONS
Press to skip backwards or forwards on a connected DVD/BD player or iPod.
8
STOP/PLAY BUTTON
Press to stop/start playback on a connected DVD/BD player or iPod.
9
MUTE BUTTON
Mutes the sound of a connected device.
10
VOLUME CONTROL BUTTONS
Adjusts the volume of the selected device.
11
MO/ST BUTTON
Select MONO or STEREO for radio broadcasts.
12
TONE BUTTON
You can adjust the bass and treble level.
13
SETUP/MENU BUTTON
Displays the SETUP menu.
14
UP/DOWN/LEFT/RIGHT BUTTONS
Used to navigate the menus.
15
RETURN BUTTON
Used to return to the previous menu from the SETUP menu.
16
FUNCTION SELECTOR BUTTONS
Used to select an input source.
17
AV SYNC BUTTON
Used to select the Audio Delay Mode.
18
ASC BUTTON
Used to set the Auto Sound Calibration function.
19
SUBWOOFER BUTTON
Used to select the Subwoofer.
20
INPUT SELECT,
TV SOURCE BUTTON
Toggles to find and select an input source.
Press to select a connected TV's video source.
21
BD BUTTON
To change to BD mode, press the BD button.
22
DVD BUTTON
To change to DVD mode, press the DVD button.
23
RDS SELECTION BUTTONS
Use the RDS function to receive FM stations.
24
SLEEP BUTTON
Used to set the Sleep Timer.
English
HW-D700_D770S_ELS_0609.indd 11
11
2011-06-09
5:37:30
Getting Started
25
DIMMER BUTTON
Adjusts the brightness of the display.
26
DSP BUTTON
Used to select the SFE mode.
27
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
28
SEARCH BUTTON
Press to search backwards or forwards.
29
PAUSE BUTTON
Pauses playback on a connected device.
30
TUNING/CHANNEL BUTTONS
Used to change the radio broadcasting frequency or TV channel.
31
S.DIRECT BUTTON
Press to select S.DIRECT mode.
32
TUNER MEMORY BUTTON
Used to set a preset radio frequency.
33
INFO BUTTON
Display information on the connected device currently being used.
34
ENTER BUTTON
Used to select an item in the SETUP menu.
35
EXIT BUTTON
Exits the SETUP menu.
36
3D SOUND BUTTON
Press to apply 3D Sound effect.
37
CROSS OVER BUTTON
Press to adjust the crossover frequency.
12
English
HW-D700_D770S_ELS_0609.indd 12
2011-06-09
5:37:31
01
Getting Started
Installing batteries in the Remote Control
* Battery size: AAA
✎ NOTE
Follow these precautions to avoid leaking or cracking cells:





Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
Assuming typical AVR usage, the batteries last for about one year.
Use the correct type of batteries. Batteries that look similar may differ in voltage.
Always replace both batteries at the same time.
Do not expose the batteries to heat or a flame.
Operation Range of the Remote Control
The remote control can be used up to approximately 7 meters in a straight line. It can also be operated
at a horizontal angle of up to 30&deg; from the remote control sensor.
Bi-AMP
English
HW-D700_D770S_ELS_0609.indd 13
13
2011-06-09
5:37:31
Connections
This section involves various methods of connecting the AV receiver to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Speaker Positioning
There are two methods for positioning the speakers.
When using Dolby Pro Logic IIz, place the Surround Back Speakers in the FHL, FHR position and connect
them to SURROUND BACK/ FRONT HEIGHT terminal(s).
* Speakers are provided with model HW-D770S only. Model HW-D700 does not come with
speakers.
FHL
FHR
6.6~9.8 feet (2~3m)
6.6~9.8 feet (2~3m)
AV RECEIVER
AV RECEIVER
Bi-AMP
Bi-AMP
SL
SR
SBL
SL
SR
SBR
L, R, C, SW, SL, SR, SBL, SBR ( Dolby Pro Logic IIx )
L, R, C, SW, SL, SR, FHL, FHR( Dolby Pro Logic IIz)
Position of AV Receiver
Place the AV Receiver on a dedicated stand or rack.
Subwoofer g
The position of the subwoofer is not so critical. Place it anywhere you like.
Subwoofer function (HW-D770S only)
Active subwoofer with integrated 150W amplifier
provides rich bass sound.
• Connect the SW OUT terminal of the amplifier to the
INPUT terminal of the subwoofer speaker.
• Press the POWER button on the rear side of the
subwoofer to turn the power on.
• Using the subwoofer’s VOLUME control, you can set the
desired bass level (See page 39 &quot;Setting the Speaker
Level&quot; to set the subwoofer level in the menu).
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45&deg;) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the centre speaker or place them slightly in
front of the centre speaker.
14
English
HW-D700_D770S_ELS_0609.indd 14
2011-06-09
5:37:32
02
Connections
Centre Speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 60 to 90cm above your ears, facing slightly downward.
Unlike the front and centre speakers, the surround speakers are used to handle mainly sound effects and
sound will not come from them all the time.
Surround Back Speakers
SBL SBR
(Using Dolby Pro Logic IIx)
If you are using two rear centre speakers, place them behind the listening position.
Place the surround back speaker about 70 cm to 1 m.
Front Height Speakers
FHL FHR
(Using Dolby Pro Logic IIz)
When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR position above the
front L and front R speakers at least 1 m above each one.
✎ NOTE
 When you attach the speakers to the wall, make sure to fasten them tightly so they do not fall off.
Speaker Configuration
For the best surround-sound experience, you should connect seven speakers and a powered
subwoofer. The following table shows which channels you should use based on the number of
speakers you have.
2 speakers
3 speakers
4 speakers
5 speakers
7 speakers
7 speakers
(DPL IIx)
(DPL IIz)
SBL
FHL
SBR
FHR
✎ NOTE
 No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
 If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field
generated by the speaker. If this occurs, place the speaker away from your TV set.
English
HW-D700_D770S_ELS_0609.indd 15
15
2011-06-09
5:37:34
Connections
Connecting the Speakers
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
FRONT (R)
SURROUND (R)
SURROUND BACK (R)
SURROUND BACK (L)
FRONT (L)
ACTIVE SUBWOOFER
SUBWOOFER
OUT
ONLY FOR
UPDATE
CENTRE
LINE OUT
SURROUND (L)
SUBWOOFER
OUT
ONLY FOR
SERVICE
16
Model HW-D700
AV Receiver
HW-D700
Model HW-D770S
AV Receiver
FRONT SPEAKER
CENTRE SPEAKER
SURROUND SPEAKER
SURROUND BACK SPEAKER
ACTIVE SUBWOOFER
HW-D700
PS-FC770S
PS-CC770S
PS-RC770S
PS-BC770S
PS-AW730
English
HW-D700_D770S_ELS_0609.indd 16
2011-06-09
5:37:37
02
 Speakers are provided with model HW-D770S only. Model HW-D700 does not come with speakers.
 One Active Subwoofer is provided, if you would like to use another, purchase it from the retailer
where you bought the player and connect it to the other SUBWOOFER OUT Jack.
Connections
✎ NOTE
 Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or
objects into the duct (hole).
 Never touch speaker terminals while the power is on. Doing so could result in electric shock.
 Make sure the polarities (+ and -) are correct.
 If you want to use two active subwoofer speakers, connect both subwoofer speakers into the
SUBWOOFER OUT terminals in the rear panel.
 When using Dolby Pro Logic IIz, connect the Front Height speakers (FHL,FHR) to the Surround
Back Speaker terminals.
Attaching the Toroidal Ferrite Core to the Speaker Cable
LINE OUT
SUBWOOFER
OUT
1. Open the toroidal ferrite cores by pulling the lock lever.
2. Arrange all the speaker cables that are connected to the unit and make a loop.
• Attach the ferrite core as close as possible to the unit.
3. Place the toroidal ferrite core on the looped speaker cable as shown, and then press it closed it
until you hear a click.
English
HW-D700_D770S_ELS_0609.indd 17
17
2011-06-09
5:37:42
Connections
Connecting the Bi-AMP Speaker
Connect the tweeter (high range) port and woofer (low range) to the front port and surround back speaker
port respectively as appropriate. Then, you can use the bi-amplification feature that supports enriched high
range and base tones.
Bi-AMP Speaker R
Bi-AMP Speaker L
Tweeter
Tweeter
Woofer
Woofer
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
1. Connect the FRONT L connector (rear side of main unit) to the Tweeter port in the front left
speaker.
2. Connect the FRONT R connector (rear side of main unit) to the Tweeter port in the front right
speaker.
3. Connect the SURROUND BACK L connector (rear side of main unit) to the Woofer port in the
front left speaker.
4. Connect the SURROUND BACK R connector (rear side of main unit) to the Woofer port in the
front right speaker.
! CAUTION
 If Bi-amp is active, you may encounter a restricted access if you have not removed the shorting bar
(like a jumper) in both tweeter and subwoofer ports in the front speaker.
 Before you can use bi-amp, ensure that you use a speaker that supports bi-amplifying.
✎ NOTE
 To enable the Bi-Amp feature, you must set 7.1 CHANNEL to Bi-AMP in SETUP menu. See page 37.
 With the Bi-amp feature, you can use up to 5.1 channels for speaker output in the main unit.
18
English
HW-D700_D770S_ELS_0609.indd 18
2011-06-09
5:37:46
02
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set-top box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
By connecting through the HDMI(High-Definition Multimedia Interface) interface, you can play back digital
video and audio.
DVD or
Blu-ray Player
SAT
(Cable/Satellite/
Set-top box)
Game console
or
HDTV Tuner
(HDTV Terrestrial
Receiver)
Connections
Connecting External Devices/your TV via HDMI
Camcorder
ONLY FOR
UPDATE
• Using two HDMI OUT
jacks, you can connect two
TVs or projectors at the
same time.
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
OPTICAL
OUT
• Connect it if you want to use
Anynet+. (If connected TV support
ARC, it is not necessary to connect
the OPTICAL OUT.)
English
HW-D700_D770S_ELS_0609.indd 19
19
2011-06-09
5:37:50
Connections
MAIN Jack
• Supports Anynet+ and ARC.
• Supports Full HD and 3D.
SUB Jack
• Does not support Anynet+ and ARC.
• When both Main and SUB are connected at the same time, output signal of SUB will be the same to that
of Main, which matches specifications of the TV connected to the Main jack.
JACK
Anynet+
ARC
Resolution
3D
MAIN
O
O
1080p
O
SUB
X
X
1080p
O
✎ NOTE
 When a 3D TV is connected to the Main and a 2D TV is connected to SUB at the same time, both Main and
Sub output 3D signal and the TV connected to SUB will display nothing.
 If your TV supports ARC function, connect to ARC support port of TV. (To enable ARC function for the TV
connected to SUB jack, a TV that supports ARC function should have been connected to the MAIN jack.)
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV must
support High-bandwidth Digital Content Protection System (HDCP). This product supports HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
✎ NOTE
 Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is
protected by CPPM, use a player supporting CPPM.
 The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
 Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
20
English
HW-D700_D770S_ELS_0609.indd 20
2011-06-09
5:37:55
02
Connections
HDMI Function
Using Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung TV's
remote control. Anynet + can be used by connecting this AV Receiver to a SAMSUNG TV using an
HDMI Cable. This is only available with SAMSUNG TVs and SAMSUNG AV Products that support
Anynet+.
1. Connect the AV receiver to a Samsung TV with an HDMI cable. (See page 19)
2. Set the Anynet+ function on your TV.
(See the TV instructions manual for more information.)
• You can operate the volume on the AV receiver by using Volume buttons on the TV remote
control.
To Turn on Anynet+
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
2.
3.
4.
5.
Press the ▲▼ buttons to select OPTION, and then press the ENTER button.
Press the ▲▼ buttons to select HDMI SETUP, and then press the ENTER button.
Press the ▲▼ buttons to select HDMI ANYNET+, and then press the ENTER button.
Press the ▲▼ buttons to set ANYNET+ to ON, and then press the ENTER button.
To exit setup mode
• Press the SETUP/MENU or EXIT button on the remote control.
SETUP OFF appears on the display and Setup Mode is exited.
✎ NOTE
 If you use an HDMI cable to connect a Samsung TV to your AV Receiver, you can operate the AV
receiver using the TV’s remote control. This function is available only in connection with Samsung
TV and DVD player supporting Anynet + (HDMI-CEC).
 Please check your TV for the ANYNET+ logo. If your TV has an ANYNET+ logo, then it supports
the Anynet+ function.
 When you are making Anynet+ connection, do not connect more than two AV receivers (Anynet+
installed). Otherwise, it can cause a malfunction.
English
HW-D700_D770S_ELS_0609.indd 21
21
2011-06-09
5:37:55
Connections
Connecting to your TV
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
or
VIDEO
IN
COMPONENT
IN
OPTICAL
OUT
AUDIO
OUT
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable (not supplied) from
the Component Video Output (PR, PB and Y) jacks on the back of your AV Receiver to the Component Video Input
jacks on your TV.
OR
Connect the Video cable (not supplied) from the VIDEO OUT (MONITOR) jack on the back of your AV Receiver to
the Video Input jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your AV Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your AV Receiver to the Audio Out of the TV.
22
English
HW-D700_D770S_ELS_0609.indd 22
2011-06-09
5:37:55
02
Connections
Connecting a DVD or BD(Blu-ray) Player
VIDEO
IN
COMPONENT
IN
or
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
or
AUDIO
OUT
VIDEO
OUT
COMPONENT
OUT
OPTICAL
OUT
DVD or BD Player
or
Video Connection
Connect a Component video cable (not supplied) from the COMPONENT IN (BD/DVD) (PR, PB and Y) jacks on the
back of your AV Receiver to the Component Video Output jacks on your DVD/BD player.
OR
Connect a Video cable (not supplied) from the VIDEO IN (BD/DVD) jack on the back of your AV Receiver to the
Video Output jack on your DVD/BD player.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your AV Receiver to the Digital Output of the DVD/BD player.
OR
Connect AUDIO IN (BD/DVD) on your AV Receiver to the Audio Out of the DVD/BD player.
English
HW-D700_D770S_ELS_0609.indd 23
23
2011-06-09
5:37:59
Connections
Connecting a Cable, Satellite or Set-top Box
VIDEO
IN
COMPONENT
IN
or
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
or
SAT(Cable/Satellite/Set-top box)
VIDEO
OUT
AUDIO
OUT
COMPONENT OPTICAL
OUT
OUT
or
Video Connection
Connect a Component video cable (not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks on the
back of your AV Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable (not supplied) from the VIDEO IN (SAT) jack on the back of your AV Receiver to the Video
Output jack on your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your AV Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your AV Receiver to the Audio Out of the SAT.
✎ NOTE
 Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
 If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
24
English
HW-D700_D770S_ELS_0609.indd 24
2011-06-09
5:38:03
02
Connections
Connecting a CD Player
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
or
AUDIO
OUT
OPTICAL
OUT
COAXIAL
OUT
CD Player
Audio Connection
Connect the Digital Input (COAXIAL, OPTICAL1~3) on your AV Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your AV Receiver to the Audio Out of the CD player.
✎ NOTE
 Connect the audio cable's red plug to the red jack and white cable to the white jack.
 If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the
main unit.
 If the CD player has only OPTICAL digital output jack, connect it to OPTICAL1 or 2 JACK of the main
unit. Please see &quot;Audio Setup&quot; at Page 35.
English
HW-D700_D770S_ELS_0609.indd 25
25
2011-06-09
5:38:07
Connections
Connecting Using the External Amplifier (Ex. Second Room)
This setup allows 7.1-channel playback in your main listening room and 2-channel stereo playback in
Second Room, with a same source in each room.
• Use an RCA audio cable to connect the AV receiver’s LINE OUT L/R jacks to an analogue audio
input on your Second Room amplifier.
• Connect your Second Room speakers to the speaker terminals on your Second Room amplifier.
Install speaker
in sub space
AV
RECEIVER
Bi-AMP
SL
SR
SBL
B
Second Room
Connecting using the external amplifier
SBR
R
Install speaker in main space
LINE OUT
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
✎ NOTE





Second Room
Usually, the secondary amplifier is used in a second room.
Line Out only outputs analogue signal.
Line Out does not provide the Volume Control.
The external amplifier with volume control (like AV Receiver or Pre-Main Amplifier) should be used.
The Volume can be controlled in the external amplifier.
26
English
HW-D700_D770S_ELS_0609.indd 26
2011-06-09
5:38:11
02
You can listen to audio from an iPod through the main unit. For iPod operation with your receiver, see
this page and pages 55 ~ 56.
Connections
Connecting an iPod
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
1. Connect the iPod dock connector to the iPod jack on your reciever.
2. Place the iPod in the Dock.
• If you want to play a movie stored in your iPod player, you should set the player's TV Out option to
On before inserting it into the dock. See pages 55 ~ 56.
3. Press the iPod button on the remote control.
• You can also use the INPUT SELECT on the main unit.
The mode switches as follows :
FM TV BD/DVD SAT GAME AUX CD IPOD AUDIO IPOD VIDEO
✎ NOTE
 You must have the VIDEO (Monitor or TV) output connected to your TV to view iPod video.
See page 22.
 Adjust the volume to a moderate level before you connect your iPod and AV Receiver.
 When the unit is powered on and you connect an iPod, the unit will charge your iPod's battery.
 Make sure to connect the dock connector so that the label “SAMSUNG” faces upward.
English
HW-D700_D770S_ELS_0609.indd 27
27
2011-06-09
5:38:16
Connections
Disconnecting an iPod
Follow the steps below to prevent damage to an iPod and data when disconnecting from your
AV receiver.
1. Use the INPUT SELECT on the main unit to switch to a mode other than IPOD AUDIO or IPOD
VIDEO.
OR
1. Turn off the AV Receiver.
2. Disconnect the iPod player from the iPod dock, or remove the iPod dock connector from the AV
receiver.
iPod/iPhone Models You Can Use with This Product
 iPod touch (3rd generation)
 iPod touch (2nd generation)
 iPod touch (1st generation)
 iPod classic
 iPod with video
 iPod with dock connector
 iPod with Click Wheel





iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)




iPhone 4
iPhone 3GS
iPhone 3G
iPhone
✎ NOTE
 “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPods and
has been certified by the developer to meet Apple performance standards.
 “Made for iPhone” means that an electronic accessory has been designed to connect specifically to iPhones
and has been certified by the developer to meet Apple performance standards.
 Apple is not responsible for the operation of this device or its compliance with safety and regulatory
standards.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
iPhone is a trademark of Apple Inc.
28
English
HW-D700_D770S_ELS_0609.indd 28
2011-06-09
5:38:20
02
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall
or other rigid surface.
Connections
Connecting the FM Antenna
3.
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
FM antenna (supplied)
✎ NOTE
 Do not place the antenna cable close to the power cord. Keep it as far away as possible.
 If you experience poor FM reception, use an external antenna.
Connecting AUX Components
You can connect external devices you use for a short time (camcorder, game console, mobile equipment,
etc.) to the front of this unit for convenience.
Bi-AMP
VIDEO
OUT
AUDIO
OUT
Camcorder
English
HW-D700_D770S_ELS_0609.indd 29
29
2011-06-09
5:38:20
Setup
For your convenience, you can set this AV receiver's features for the best use.
Before Using the AV Receiver
Turning On/Off
Connect the power plug to the outlet.
This unit will set to Standby mode.
Press the POWER button on the main unit for 2 seconds.
• This unit will be turned on.
• You can also turn the unit on/off by pressing the POWER button on the remote control.
Remote Control Functions
You can operate your AMP (this AV receiver)/ TV and BD(Samsung only)/DVD player with this remote
control. See pages 59 ~ 60 for more details.
To Select a Function
Method 1
Press the INPUT SELECT button on the remote control.
• Each time you press this button, FM TV BD/DVD SAT GAME AUX CD IPOD AUDIO
IPOD VIDEO will be selected in turn.
Method 2
Press the BD/DVD, SAT, GAME/TV, CD, iPod or TUNER button.
• You can directly select the desired function.
Home Menu
Use the HDMI cable to connect between main unit and
monitor. Press SETUP/MENU to display the “INPUT”
message on the display screen. You will see the OSD
menu in a few seconds.
✎ NOTE
 The OSD menu will be displayed only if you use the
HDMI cable for the connection.
INPUT
INPUT SELECTION
SPEAKER
Q SURROUND
OPTION
&gt; MOVE
SELECT
' RETURN
EXIT
 For using the OSD menus, refer to using the menus
on the display screen.
 The OSD (On Screen Display) may change in this
product after you upgrade the software version.
30
English
HW-D700_D770S_ELS_0609.indd 30
2011-06-09
5:38:23
03
Setup
Selecting Digital/HDMI/Analogue
You can listen to sound of analogue, HDMI, optical input using this unit.
1. Press the INPUT SELECT button on the remote control to select a
desired function (BD/DVD, SAT, TV, CD, AUX). See page 30.
2. Press the AUDIO ASSIGN button on the remote control to select the
audio input source of the external device you have connected.
• Each time you press this button, the input mode changes as
follows:
• For BD/DVD function






• For SAT function
• For TV function
• For CD function

• For AUX function

✎ NOTE
 You can also change the input mode by pressing the AUDIO ASSIGN button on the front of your
AV Receiver.
 You can enjoy Dolby Digital or DTS if you connect the digital audio output jack of an external
audio component to the optical or coaxial digital audio input jack on the main unit.
 For the TV function, the TV ARC menu will be displayed only if an ARC-compliant TV is
connected.
English
HW-D700_D770S_ELS_0609.indd 31
31
2011-06-09
5:38:24
Setup
Setup Menu Tree
Here’s a quick look at how the setup menus are organized on your AV Receiver.
INPUT
INPUT SELECTION
BD/DVD
OPTICAL1, 2
COAXIAL
OPTICAL1, 2
COAXIAL
OPTICAL1, 2
COAXIAL
SAT
CD
SPEAKER
SPEAKER SIZE
7.1 CHANNEL
SPEAKER DISTANCE
SPEAKER LEVEL
TEST TONE
SURROUND
DPLIIx
DTS NEO:6
EX/ES
OPTION
AUDIO SYNC
TONE CONTROL
MP3 ENHANCER
SMART VOLUME
AUTO CALIBRATION
DRC
DUAL MONO
HDMI SETUP
CONVERT VIDEO
32
English
HW-D700_D770S_ELS_0609.indd 32
2011-06-09
5:38:28
03
Setup
SPEAKER
SPEAKER SIZE
FRONT
LARGE
SMALL
CENTER
LARGE
SMALL
NONE
SURROUND
LARGE
SMALL
NONE
SURROUND BACK
LARGE
SMALL
NONE
FRONT HEIGHT
LARGE
SMALL
SUBWOOFER
YES
NO
CROSSOVER
7.1 CHANNEL
60Hz, 80Hz, 100Hz, 120Hz, 150Hz, 180Hz, 200Hz
SURR.BACK
PLIIz
BI-AMP
SPEAKER DISTANCE
FRONT LEFT
FRONT RIGHT
CENTER
SURROND LEFT
0.3 ~ 9.0m (0.3m step) , default : 3.0m
SURROUND RIGHT
SURROUND BACK LEFT
FRONT HEIGHT LEFT
SURROUND BACK RIGHT
FRONT HEIGHT RIGHT
SUBWOOFER
SPEAKER LEVEL
FRONT LEFT
FRONT RIGHT
CENTER
SURROND LEFT
SURROUND RIGHT
-10 ~ +10dB (1dB step) , default : 00dB
SURROUND BACK LEFT
FRONT HEIGHT LEFT
SURROUND BACK RIGHT
FRONT HEIGHT RIGHT
SUBWOOFER
TEST TONE
AUTO
move to &quot;Test Tone check Page&quot;
MANUAL
✎ NOTE
 If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed to the Front
Height Speaker (FHL/FHR).
English
HW-D700_D770S_ELS_0609.indd 33
33
2011-06-09
5:38:28
Setup
SURROUND
DPLIIx
PANORAMA
OFF
ON
DIMENSION
-7~+7
CENTER WIDTH
0~7
DTS NEO:6
CENTER IMAGE
0~5
EX/ES
AUTO
OFF
ON
OPTION
AUDIO SYNC
TONE CONTROL
0ms~240ms (10ms step)
TONE
OFF
ON
BASS
-6dB ~ +6dB (1dB Step)
TREBLE
-6dB ~ +6dB (1dB Step)
MP3 ENHANCER
OFF
ON
SMART VOLUME
OFF
ON
AUTO CALIBRATION
MODE
OFF
move to &quot;Auto Calibration Measurement Page&quot;
MEASUREMENT
DRC
AUTO
DUAL MONO
CH1
HDMI SETUP
AUTO SYNC
ON
MINIMUM
STANDARD
MAXIMUM
CH2
BOTH
OFF
ON
AVR
TV
OFF
ON
OFF
AUTO
HDMI AUDIO
HDMI ANYNET+
ARC
CONVERT VIDEO
34
AUTO
BYPASS
English
HW-D700_D770S_ELS_0609.indd 34
2011-06-09
5:38:28
03
Setup
Audio Setup
Selecting a Source Device And Connection Jack (Digital Audio In)
Select the external devices you have connected to the receiver.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches
between INPUT and SETUP OFF.
2. Press the ENTER button to select INPUT.
3. Press the ENTER button to select INPUT SELECTION.
4. Press the ▲▼ buttons to select a desired jack.
• Devices switch as follows; BD/DVD, SAT, CD

✎ NOTE

 You can also use the SETUP, ,,., ENTER, RETURN
buttons on the front of your AV Receiver.
Setting the Speaker Size
Signal outputs and frequency response from the speaker will be adjusted according to your speaker
configuration and whether certain speakers are used or not.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SPEAKER, and then press
the ENTER button.

3. Press the ▲▼ buttons to select SPK SIZE, and then press the
ENTER button.
4. Press the ▲▼ buttons to select the speaker you want, and
then press the ENTER button.
• Each time you press the ▲▼ buttons, FRONT
CENTER  SURR  SBACK(DPLIIx) / FRONTH(DPLIIz) 
 SUBW  CROVR will be selected in turn.

5. Press the ▲▼ buttons to set the mode (LARGE, SMALL etc.)
for the selected speaker.
6. Repeat steps 2-5 to set the mode for each speaker.
SPEAKER SIZE
USER
&gt; MOVE
FRONT
: SMALL
LARGE
CENTER
: SMALL
SMALL
SURROUND
:
SMALL
SURROUND BACK
:
SMALL
SUBWOOFER
:
YES
CROSSOVER
:
100Hz
SELECT
' RETURN
EXIT
English
HW-D700_D770S_ELS_0609.indd 35
35
2011-06-09
5:38:28
Setup
- To exit setup mode • Press the SETUP/MENU or EXIT button on the remote control.
SETUP OFF appears on the display and Setup Mode is exited.
Setting the Speaker
SPEAKER
Possible Settings
Default Setting
FRONT (Front)
LARGE, SMALL
SMALL
CENTER (Centre)
LARGE, SMALL, NONE
SMALL
SURR (Surround)
LARGE, SMALL, NONE
SMALL
SBACK (Surround Back)
LARGE, SMALL, NONE
SMALL
FRONTH (Front Height)
LARGE, SMALL
SMALL
SUBW (Subwoofer)
YES, NO
YES
CROVR (Crossover Frequency)
60, 80, 100,120, 150, 180, 200(Hz)
100Hz
•
•
•
•
•
•
LARGE : Select when using large speakers. You can listen to full range sound.
SMALL : Select this when using small speakers.
NONE : Select when no speaker is used.
YES (subwoofer) : Select when using the subwoofer speaker.
NO (subwoofer) : Select when not using the subwoofer speaker.
CROVR : Select the crossover frequency for the best bass response in your speakers.
✎ NOTE
 You can also use the SETUP, ,,., ENTER, RETURN buttons on the front of your AV Receiver.
 When the Front speaker is only set to LARGE, you can select LARGE of other speakers.
 When the Surround speaker is set to LARGE, you can select LARGE of SBACK (Surround Back)
speaker.
 When the 7.1 CHANNEL is set to PLIIz, you can not select NONE of surround speaker and front
height speaker.
 You can also change the crossover frequency by using the CROSS OVER, &lt;, &gt; buttons on the
remote control.
36
English
HW-D700_D770S_ELS_0609.indd 36
2011-06-09
5:38:29
03
Setup
Connection Setting For Surround Back
Settings for the surround back speaker differ depending on the connection method and installation site
of the speaker to be connected. You must configure the 7.1 CHANNEL settings according to the
connected speaker before you listen to music properly.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.

2. Press the ▲▼ buttons to select SPEAKER, and then press the
ENTER button.
3. Press the ▲▼ buttons to select 7.1 CHANNEL, and then
press the ENTER button.
4. Press the ▲▼ to select a proper setting for the surround back
speaker.
• SURR.BACK : Select this if you want to install the surround
back speaker in the default settings. With this setting, you can
enable the Dolby Pro Logic IIx mode.
• PLIIz : Select this if you want to install the surround
back speaker in the top front corner. With this
setting, you can enable the Dolby Pro Logic IIz
INPUT
mode.
SPEAKER
• BI-AMP : Select this if you want to connect the
Bi-Amp compliant speaker to the surround back
Q SURROUND
port. With this setting, you can enable the Bi-Amp
OPTION
feature.
&gt; MOVE

SPEAKER SIZE
7.1 CHANNEL
SURR.BACK
SPEAKER DISTANCE
PLIIz
SPEAKER LEVELBI-AMP
TEST TONE
SELECT
' RETURN
EXIT
✎ NOTE
 Depending on the 7.1 CHANNEL settings, the surround back speaker or front height speaker
menus may not be activated or may differ in the speaker menu: SPEAKER SIZE, SPEAKER
LEVEL, SPEAKER DISTANCE.
 Depending on your setting, you may not use different features simultaneously. If you set SURRBACK, for instance, you cannot use the following features: PLIIz and BI-AMP.
English
HW-D700_D770S_ELS_0609.indd 37
37
2011-06-09
5:38:29
Setup
Setting the Speaker Listening Distance
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of
the audio signals from the centre and surround speakers.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.

2. Press the ▲▼ buttons to select SPEAKER, and then press
the ENTER button.
3. Press the ▲▼ buttons to select SPK DISTANCE, and then
press the ENTER button.
4. Press the ▲▼ buttons to select the speaker you want.
• Each time you press the ▲▼ buttons, F.L  F.R CEN 
S.L  S.R  SBL  SBR  S.W will be selected in turn.

5. Press the ◄ ► buttons to set the Speaker Distance.
• For the FRONT LEFT, FRONT RIGHT, CENTER, SURR.
LEFT, SURR. RIGHT, SURRBACK.LEFT,
SURRBACK.RIGHT and SUBWOOFER Speakers,
you can set the distance from the speaker to
FRONT LEFT
listening position between 1ft ~ 30ft (0.3~9.0m) in
FRONT RIGHT
intervals of 1ft (0.3m).
CENTER
SPEAKER DISTANCE
3.0m
►
3.0m
3.0m
SURROUND LEFT
3.0m
SURROUND RIGHT
3.0m
▼
&gt; MOVE
SELECT
' RETURN
EXIT
- Setting Speaker Distance Set the distance from the speaker to listening position in intervals of 1ft(0.3m).
• F.L (front left) : 0.3 ~ 9.0m
• SW (subwoofer) : 0.3 ~ 9.0m
• F.R (front right) : 0.3 ~ 9.0m
• SBL (surround back left) : 0.3 ~ 9.0m
• S.L (surround left) : 0.3 ~ 9.0m
• SBR (surround back right) : 0.3 ~ 9.0m
• S.R (surround right) : 0.3 ~ 9.0m
• FHL (front height left) : 0.3 ~ 9.0m
• CEN (centre) : 0.3 ~ 9.0m
• FHR (front height right) : 0.3 ~ 9.0m
✎ NOTE
 If the listening position is beyond the range of the speaker distance setup, set the speaker
distance to the maximum.
 If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed to the Front
Height Speaker (FHL/FHR).
38
English
HW-D700_D770S_ELS_0609.indd 38
2011-06-09
5:38:30
03
Setup
Setting the Speaker Level
You can set the balance and level of speakers.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SPEAKER, and then press
the ENTER button.

3. Press the ▲▼ buttons to select SPK LEVEL, and then press
the ENTER button.
4. Press the ▲▼ buttons to select the speaker you want.
• Each time you press this button, F.L  F.R CEN  S.L 
S.R  SBL  SBR  S.W will be selected in turn.

5. Press the ◄ ► buttons to set the Speaker Level mode.
• You can adjust it from -10 to +10dB in 1 step increments.
• The sound gets quieter at -10dB and louder at
+10dB.
SPEAKER LEVEL
FRONT LEFT
◄
0dB
FRONT RIGHT
0dB
CENTER
0dB
SURROUND LEFT
0dB
SURROUND RIGHT
0dB
►
▼
&gt; MOVE
SELECT
' RETURN
EXIT
- Setting Speaker Level • F.L (front left) : -10 ~ +10dB
• SW (subwoofer) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• FHL (front height left) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• FHR (front height right) : -10 ~ +10dB
✎ NOTE
 If Dolby Pro Logic IIz is set to On, the Surround Back speaker (SBL/SBR) is changed to the Front
Height Speaker (FHL/FHR).
 You can also change the subwoofer level by using the SUBWOOFER, &lt;, &gt; buttons on the remote
control.
English
HW-D700_D770S_ELS_0609.indd 39
39
2011-06-09
5:38:31
Setup
Setting the Test Tone
Use the test tone to check the speaker connection status or level.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SPEAKER, and then press
the ENTER button.

3. Press the ▲▼ buttons to select TEST TONE, and then press
the ENTER button.
4. Press the ▲▼ buttons to select the option you want, and then
press the ENTER button.
• AUTO : Test signal will be automatically output as follows;
F.L  CEN  S.W  F.R  S.R  SBR  SBL  S.L.
- During test tone output, press the ▲▼ buttons to adjust the
speaker output level from -10 to +10 dB by 1 step.
• MANUAL : Enables you to adjust the output level of the
speaker manually.
1) Press the ENTER button to select the speaker
you want.
Each time you press the ENTER button, F.L 
CEN  S.W  F.R  S.R  SBR  SBL S.L
will be selected in turn.
2) Press the ▲▼ buttons to set the Test Tone
mode you want.
You can adjust the speaker output level from -10
to +10dB by 1 step.
The sound gets quieter at -10dB and louder at
+10dB.

MANUAL
▲FL
C
0dB
0dB
▼
SL
0dB
FR
0dB
SW
0dB
SR
0dB
USER
SBL
0dB
&gt; MOVE
SBR
0dB
SELECT
' RETURN
EXIT
- Test Tone Output • F.L (front left) : -10 ~ +10dB
• F.R (front right) : -10 ~ +10dB
• S.L (surround left) : -10 ~ +10dB
• S.R (surround right) : -10 ~ +10dB
• CEN (centre) : -10 ~ +10dB
• S.W (subwoofer) : -10 ~ +10dB
• SBL (surround back left) : -10 ~ +10dB
• SBR (surround back right) : -10 ~ +10dB
- To stop test tone • Press the SETUP/MENU button once.
SETUP OFF appears on the display and test tone stops.
✎ NOTE
 In the Dolby Pro Logic IIz mode, test signal will be automatically output as follows : F.L  FHL 
CEN  S.W  FHR  F.R  S.R  S.L.
40
English
HW-D700_D770S_ELS_0609.indd 40
2011-06-09
5:38:31
03
Setup
Setting Dolby Pro Logic Mode
This mode provides up to 7.1 channel sound from 2 channel sources, or provides 7.1 channel sound
from 5.1 channel sources for music or movie mode.
Press the PROLOGIC button on the remote control.
•
•
•
•
•
•
MOVIE : Adds realism to the movie soundtrack.
MUSIC : Provides up to 7.1 channel surround sound for digital, analogue or existing stereo sources.
GAME : Enhances the excitement of the game’s sound.
MATRIX : You will hear up to 7.1 channel surround sound.
PL (Pro Logic) : You will experience a surround effect with 5.1 channel surround sound.
OFF : Output the original signal as it is without applying the sound field effect or any other sound
effect.
Surround Setup
Setting Dolby Pro Logic IIx
This function works only in Dolby Pro Logic IIx MUSIC mode.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SURROUND, and then press
the ENTER button.
3. Press the ▲▼ buttons to select DPLIIx, and then press the
ENTER button.

4. Press the ▲▼ buttons to select the option you want, and then
press the ENTER button.
• PANORAMA : Press the ▲▼ buttons to select ON or OFF.
(This mode extends the front stereo image to include the
surround speakers for an exciting &quot;wraparound&quot; effect with

side wall imaging.)
• DIMENSION : Press the ◄ ► buttons to set from -7 to 7.
(Incrementally adjusts the sound field (DSP)from the front or
surround.)
• C- WIDTH : Press the ◄ ► buttons to set from 0 to 7.
(This sets the width of the centre sound image. The higher the setting, the less sound comes
from the centre speaker.)
✎ NOTE
 PANORAMA, DIMENSION and CENTER WIDTH settings are enabled only if the Dolby Pro Logic
Mode is set to MUSIC.
 You cannot use Dolby Pro Logic llx mode for multi channel signals such as Dolby Digital, Dolly
Digital +, Dolby true HD, DTS, DTS-HD Master Audio.
 Pro Logic works only for PCM audio signals with sampling frequencies of 32KHz, 44KHz or
48KHz.
 When Dolby Pro Logic IIz is set ON, Dolby Pro Logic IIx can not be used.
English
HW-D700_D770S_ELS_0609.indd 41
41
2011-06-09
5:38:32
Setup
Setting NEO:6 Mode
You can play back 2 channel sound over 5.1 or 7.1 channels when enjoying music or a movie.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SURROUND, and then press
the ENTER button.
3. Press the ▲▼ buttons to select DTS NEO:6, and then press
the ENTER button.
4. Press the ENTER buttons to set the C-IMAGE mode you want.

Press the ◄ ► buttons to set the C-IMAGE from 0 to 5.
This parameter adjusts the centre image through the front and
centre speakers. &quot;5&quot; is the wider.
Using NEO:6 Mode

Press the NEO:6 button on the remote control.
• MUSIC : When listening to music, you can experience
sound effects as if you are listening to the actual
performance.
• CINEMA : Adds realism to the movie soundtrack.
• OFF : Output the original signal as it is without applying the sound field effect or any other sound
effect.
✎ NOTE
 NEO:6 works only for 2-ch audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.
Setting EX/ES Mode
When surround back speakers are connected, you can listen to 7.1 multi-channel sound using the
built-in Dolby Digital Surround EX or DTS ES decoder. This function works when a Dolby Digital or DTS
source (such as a DVD player) is input, and does not work with L.PCM and Dolby Digital 2 channel
sources.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select SURROUND, and then press
the ENTER button.
3. Press the ▲▼ buttons to select EX/ES, and then press the
ENTER button.
4. Press the ▲▼ buttons to set the EX/ES mode you want.

• AUTO : If the unit receives an audio signal that it can
recognize, it will select an optimal decoder for playback in
7.1 channels.
If the amplifier does not recognize the audio signal, it will not

play in 7.1 channel automatically.
• OFF : Dolby Digital Surround EX / DTS ES decoder will not
be used for playback.
• ON : Dolby Digital or DTS signal will be played in 7.1 channel
using Dolby Digital Surround EX / DTS ES decoder.
✎ NOTE
 You cannot use DTS-ES without surround back speakers connected.
42
English
HW-D700_D770S_ELS_0609.indd 42
2011-06-09
5:38:32
03
Setup
Other Settings
Audio Sync
Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio
delay time to match the video.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches
between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.

3. Press the ▲▼ buttons to select AUDIO SYNC, and then
press the ENTER button.
4. Press the ◄ ► buttons to set the AUDIO SYNC Delay Time.
• You can adjust it from 0 to 240MS in 10MS steps.

Tone Control
This will enable you to adjust the bass and treble level.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.

3. Press the ▲▼ buttons to select TONE CONTROL, and then
press the ENTER button.
4. Press the ▲▼ buttons to select TONE, and then press the
ENTER button.

5. Press the ▲▼ buttons to select ON or OFF you want, and then
press the ENTER button.
• If it is set to TONE OFF, the Tone Control function will be
disabled.
6. Press the ▲▼ buttons to set the Tone Control mode you want.
• BASS &amp; TREBLE : Press the ◄ ► buttons to set from -6 to 6.
• Each time you press this button, TONE  BASS  TREBLE will be selected in turn.
• You can adjust it from -6 to +6dB by 1 step.
• The sound gets quieter at -6dB and louder at +6dB.
✎ NOTE
 The Tone Control function can be applied to the front channels only.
English
HW-D700_D770S_ELS_0609.indd 43
43
2011-06-09
5:38:33
Setup
MP3 Enhancer
This also helps enhance your sound experience (ex. mp3 music). Use this if you want to hear better
sound from a low quality mp3 source.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches
between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.

3. Press the ▲▼ buttons to select MP3 ENHANCER, and then
press the ENTER button.
4. Press the ▲▼ buttons to select ON or OFF.

Smart Volume
This will regulate and stabilize the volume level against a drastic volume change when changing
channels or during a scene transition.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches
between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.

3. Press the ▲▼ buttons to select SMART VOLUME, and then
press the ENTER button.
4. Press the ▲▼ buttons to select ON or OFF.

Auto Calibration Setup
By setting the calibration just once when you relocate or install the unit, you can have the unit
automatically recognize the distance between speakers, levels between channels, and frequency
characteristics to create a 7.1-channel sound field optimized for your environment.
- Before Setting 1. Plug the ASC microphone into the ASC MIC jack.
2. Place the ASC microphone at the listening position.
3. Press the ASC button on the front panel, and then press the ENTER button.
44
English
HW-D700_D770S_ELS_0609.indd 44
2011-06-09
5:38:34
03
Setup
CALIBRATION
FL
0dB
0.3m
Bi-AMP
ASC
Microphone
SL
0dB
0.3m
FR
0dB
0.3m
SW
0dB
0.3m
C
0dB
0.3m
SR
0dB
0.3m
USER
SBL
0dB
0.0m
&gt; MOVE
SBR
0dB
0.0m
SELECT
' RETURN
EXIT
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.
3. Press the ▲▼ buttons to select AUTO CALIBRATION, and
then press the ENTER button.
4. Press the ▲▼ buttons to select MEASUREMENT, and then
press the ENTER button.
• To create the optimal 7.1 channel sound field, the selections
are in the following sequence:
L ➞ C ➞ R ➞ SR ➞ SBR ➞ SBL ➞ SL ➞ SW
• MODE ON : The auto calibration mode is set to on.


MODE OFF: The auto calibration mode is set to off.
To cancel the Auto Calibration setup.
This will be automatically reverted if you press the RETURN button.
• If auto calibration error occurs, see &quot;Auto Calibration Error List&quot; on page 63.
✎ NOTE
 Setting the calibration takes about 3 minutes.
 Because the volume level of the tone is fixed during the Auto Calibration Setup, you cannot adjust
the volume using the volume control.
 If the ASC microphone is disconnected during the Auto Calibration Setup, the setup will be
cancelled.
 You can also press the ASC button on the remote control to use this function.
 If Dolby Pro Logic ||z is set to ON, the selection are in the following sequence :
FL  CEN  FR  SR  FHR  FHL  SL  SW.
English
HW-D700_D770S_ELS_0609.indd 45
45
2011-06-09
5:38:34
Setup
DRC Setup
You can use this function to enjoy Dolby Digital sound when watching movies at low volume at night.
DRC compresses the audio to make the loudest sounds quieter and the quietest sounds louder.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.
3. Press the ▲▼ buttons to select DRC, and then press the
ENTER button.
4. Press the ▲▼ buttons to set the DRC you want.
• AUTO : The Dynamic Range Control will be set automatically
based on the information provided by the Dolby TrueHD
Soundtrack.
• MIN : Sets DRC effect to minimum.
• STD : Sets DRC effect to standard.
• MAX : Sets DRC effect to maximum.


Dual Mono Setup
Dual mono programs have two independent mono channels.
You can use this function when dual mono programs are played.
When you use this function, select audio channels CH1, CH2 or both Channel.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between
INPUT and SETUP OFF.
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.
3. Press the ▲▼ buttons to select DUAL MONO, and then press
the ENTER button.
4. Press the ▲▼ buttons to select the DUAL MONO option you
want.
• CH1 : Channel 1 is heard only.
• CH2 : Channel 2 is heard only.
• BOTH : Both channels are heard from front speakers.


HDMI Setup
Use this if you want to receive audio from HDMI connected external devices.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
46
English
HW-D700_D770S_ELS_0609.indd 46
2011-06-09
5:38:36
03
Setup
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.
3. Press the ▲▼ buttons to select HDMI SETUP, and then press
the ENTER button.
4. Press the ▲▼ buttons to set the HDMI Setup mode you want,
and then press the ENTER button.
5. Press the ▲▼ buttons to set you want.
• AUTO SYNC : ON, OFF
The AV receiver can be set to automatically correct any delay
between the video and the audio, based on the data from the
connected TV.
- ON : HDMI Sync is enabled.
- OFF : HDMI Sync is disabled.


• HDMI AUDIO : AVR(Audio Video Receiver), TV
This preference determines whether audio received at the HDMI IN is output by the HDMI OUT.
If you want to listen to audio from an HDMI connected external device through your HDMI
connected TV's speakers, set it to TV. Otherwise, leave it on AVR to listen to audio from the A/V
receiver.
- AVR : HDMI audio is not output
- TV : HDMI audio is output
• HDMI ANYNET+ : ON, OFF
Anynet+ is a function that enables you to control other Samsung Devices with your Samsung
TV's remote control.
- ON : Anynet+ is enabled.
- OFF : Anynet+ is disabled.
• ARC : AUTO , OFF
If you use the HDMI cable to connect between HDMI IN of an Audio Return Channel-compliant
TV and HDMI OUT (ARC) of the main unit, you can listen to the TV sound through the main unit
connected speaker without the further connection.
- AUTO : The audio signal from the TV can be sent to the HDMI OUT of the main unit.
- OFF : Turn TV ARC funtion off.
✎ NOTE
 HDMI Audio is enabled only if both the HDMI INPUT and HDMI OUT are connected properly and
working normally.
 HDMI Sync function works only if your HDMI compatible TV supports this function.
 If HDMI ANYNET+ is set to OFF, TV ARC will be set to OFF accordingly that cannot switch to
AUTO.
 The ARC function will be active only via the HDMI OUT terminal.
Video Convert Setup
You can convert the incoming composite or component video signal into a maximum quality of the
connected TV if you output the converted video via HDMI OUT.
1. Press the SETUP/MENU button on the remote control.
• Each time the button is pressed, the mode switches between INPUT and SETUP OFF.
English
HW-D700_D770S_ELS_0609.indd 47
47
2011-06-09
5:38:36
Setup
2. Press the ▲▼ buttons to select OPTION, and then press the
ENTER button.
3. Press the ▲▼ buttons to select CONV. VIDEO, and then press
the ENTER button.
4. Press the ▲▼ buttons to select BYPASS or AUTO.

• BYPASS : Converts the input video source into the digital
counterpart without changing the resolution.
• AUTO : Converts the incoming video signal before outputting
in the maximum resolution that the connected TV supports.

Video conversion flow according to the connected port
As shown in the illustration, if the unit’s HDMI Out is connected to a TV or monitor, the analogue video
source (composite or component) from the video device is processed for up-conversion automatically
for HDMI output.
If connected to a TV or monitor through Composite or Component ports, corresponding analogue
signal will be output respectively, without any conversion. In case if the unit and video source device is
connected in multiple methods (HDMI, Component and Composite video) at the same time: Video
input signal is automatically selected in the order of Component Video Composite Video.
ONLY FOR
UPDATE
LINE OUT
SUBWOOFER
OUT
ONLY FOR
SERVICE
Input
Signal
HDMI OUT
Output
Signal
Video
Conversion
HDMI IN
HDMI OUT
HDMI IN
COMPONENT OUT
COMPONENT IN
COMPONENT OUT
COMPONENT IN
VIDEO OUT
VIDEO IN
VIDEO OUT
VIDEO IN
✎ NOTE
 This enables upconverting up to a quality of 1080p.
 Auto conversion is not applied to a video source incoming from HDMI IN port.
48
English
HW-D700_D770S_ELS_0609.indd 48
2011-06-09
5:38:37
04
Operation
Operation
Using the Surround Modes
Using the S.DIRECT Button
Output the original signal as it is without applying the sound field effect or any other sound effect.
Press the S.DIRECT button.
✎ NOTE
 The screen will display “DIRECT” instead of “S.DIRECT”.
Input Signal and Surround Chart
o = active, – = inactive
Input Signal
Surround Mode
Output Channel
SL SBL
SUBW
SR SBR
Display Information
Signal Format
L/R
C
Dolby Digital
O
O
O
–
O
Digital + Dolby Digital
Dolby Digital EX
O
O
O
O
O
Digital +Dolby Digital EX
L, C, R, SL, SR ,SBL, SBR, SW
Dolby Digital + ProLogic IIx
O
O
O
O
O
Digital + Dolby Digital + ProLogic IIx
L, C, R, SL, SR ,SBL, SBR, SW
Dolby Digital + ProLogic IIz
O
O
O
O (Height)
O
Digital + Dolby Digital + ProLogic IIz
Dolby Digital Plus
Dolby Digital Plus
O
O
O
O
O
Digital + Dolby Digital Plus
L, C, R, SL, SR ,SBL, SBR, SW
Dolby TrueHD
Dolby TrueHD
O
O
O
O
O
Dolby TrueHD
L, C, R, SL, SR ,SBL, SBR, SW
DTS (5.1-ch)
DTS Surround
O
O
O
–
O
DTS
DTS-ES
DTS Digital + ProLogic IIx
O
O
O
O
O
DTS + ProLogic IIx
L, C, R, SL, SR ,SBL, SBR, SW
DTS Digital + ProLogic IIz
O
O
O
O (Height)
O
DTS + ProLogic IIz
L, C, R, SL, SR ,SBL, SBR, SW
DTS-ES
O
O
O
O
O
DTS ES
L, C, R, SL, SR ,SBL, SBR, SW
DTS 96/24
O
O
O
–
O
DTS 96/24
DTS-HD Master Audio
O
O
O
O
O
DTS-HD MSTR
Dolby Digital
Dolby Digitital EX
DTS 96/24
DTS-HD
LPCM Multi-Channel
2-ch PCM
Analogue 2-ch
Channel Status
L, C, R, SL, SR, SW
L, C, R, SL, SR, H, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR, SW
L, C, R, SL, SR ,SBL, SBR, SW
DTS-HD High Resolution
O
O
O
O
O
DTS-HD
L, C, R, SL, SR, SBL, SBR, SW
Multi-Channel
O
O
O
O
O
Digital + LPCM
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, H, SW
Multi-Channel
O
O
O
O (Height)
O
Digital + LPCM
Stereo
O
–
–
–
O
ProLogic IIx
O
O
O
O
O
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
ProLogic IIz
O
O
O
O (Height)
O
NEO:6
O
O
O
O
O
Digital + LPCM
Digital + LPCM + Dolby Digital +
ProLogic IIx
Digital + LPCM + Dolby Digital +
ProLogic IIz
Digital + LPCM + DTS + NEO:6
L, R, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR, H, SW
SFE
O
O
O
O
O
Digital + LPCM + LIVE SURR
Stereo
O
–
–
–
O
Analogue
ProLogic IIx
O
O
O
O
O
Analogue + Dolby Digital + ProLogic IIx L, C, R, SL, SR ,SBL, SBR, SW
ProLogic IIz
O
O
O
O (Height)
O
Analogue + Dolby Digital + ProLogic IIz
NEO:6
O
O
O
O
O
Analogue + DTS NEO:6
L, C, R, SL, SR ,SBL, SBR, SW
SFE
O
O
O
O
O
Analogue + LIVE SURR
L, C, R, SL, SR ,SBL, SBR, SW
• L/R : front speaker (left/right)
C : centre speaker
SL/SR : surround speaker (left/right)
SBL/SBR : surround back speaker (left/right)
H = FHL/FHR : front height speaker (left/right)
SW : subwoofer
L, R, SW
L, C, R, SL, SR, H, SW
• LIVE SURR : LIVE SURROUND
English
HW-D700_D770S_ELS_0609.indd 49
49
2011-06-09
5:38:39
Operation
✎ NOTE
 Channel status displays are dependent on the speaker configuration.
 SFE mode works with 2-ch signals.
 If Dolby Pro Logic IIz is set to On, the Surround Back speaker(SBL/SBR) is changed to the Front
Height Speaker(FHL/FHR), Dolby true HD, Dolby plus, DTS-HD Audio ,SFE and NE0:6 will be
output 5.1 channel.
 ProLogic IIx and ProLogic IIz works only audio signals with sampling frequencies of 32KHz,
44KHz or 48KHz.
Using the AUDIO EFFECT Button On the Front of the Main Unit
Selecting the DPLIIx mode
1. Press the AUDIO EFFECT button to select DPLIIx mode.
• Each time you press this button,

be selected in turn.

 3D SOUND will
2. Press the &lt;, &gt; button.
• Each time you press the &lt;, &gt; button, MUSIC  GAME  MATRIX  PL  PL OFF 
MOVIE will be selected in turn.
• If you turn Dolby Pro Logic IIz on, HEIGHT  PL OFF will be selected in turn.
• You can also select the DPLIIx mode by pressing the PROLOGIC button on the remote control.
Selecting the NEO:6 mode
1. Press the AUDIO EFFECT button briefly to select NEO:6 mode.
• Each time you press this button,


be selected in turn.
 3D SOUND will
2. Press the &lt;, &gt; button.
• Each time you press the &lt;, &gt; button, MUSIC  CINEMA  OFF will be selected in turn.
• You can also select the NEO:6 mode by pressing the NEO : 6 button on the remote control.
Selecting the DSP mode
1. Press the AUDIO EFFECT button to select DSP mode.
• Each time you press this button,

be selected in turn.

 3D SOUND will
2. Press the &lt;, &gt; button.
• Each time you press the &lt;, &gt; button, STEREO  HALL 1 HALL 2 
J.CLUB  CHURCH  ROCK  CLASSIC  LIVE  GAME  MOVIE  CONCERT 
STADIUM will be selected in turn.
• You can also select the DSP mode by pressing the DSP button on the remote control.
50
English
HW-D700_D770S_ELS_0609.indd 50
2011-06-09
5:38:39
04
1. Press the AUDIO EFFECT button to select 3D SOUND mode.
• Each time you press this button,


 3D SOUND will
be selected in turn.
2. Press the &lt;, &gt; button.
• Each time you press the &lt;, &gt; button, 3D SOUND ON  3D SOUND OFF will be selected in turn.
• You can also select the 3D SOUND mode by pressing the 3D SOUND button on the remote control.
Operation
Selecting the 3D SOUND mode
✎ NOTE
 The 3D sound effect will not be available for Dolby TrueHD, Dolby Digital Plus, DTS-HD Master
Audio and DTS-HD High Resolution Audio.
 You cannot use Dolby Pro Logic llx mode for Analogue multi channel signals, LPCM multi channel
signals from HDMI, Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio and DTS-HD High
Resolution Audio.
 Pro Logic works with the audio signals with sampling frequencies of 32KHz, 44KHz or 48KHz.
 The 3D sound effect will not be available for FM.
Using the SUBWOOFER button
You can set the subwoofer Level.
1. Press the SUBWOOFER button.
2. Press the ◄ ► buttons to select Subwoofer LEVEL under the
Display with S.W. (The display disappears automatically.)
- Setting the Subwoofer Level• SW (Subwoofer) : -10 ~ +10dB
Listening to the Radio
You can listen to the radio by using either automatic or manual tuning.
1. Press the INPUT SELECT button on the remote control to select FM.
2. Select a frequency (radio broadcast).
• Preset tuning :
Press the #,$ buttons on the remote control to select the preset frequency.
• Manual tuning 1 (Automatic tuning):
Press and hold the TUNING/CH ( .,, ) buttons on the remote control to automatically tune in
a frequency.
• Manual tuning 2 :
Press the TUNING/CH ( .,, ) buttons on the remote control to increase or decrease the
frequency step by step.
✎ NOTE
 You can also use the SELECT (.,,) button on the main uint to change the radio frequency.
English
HW-D700_D770S_ELS_0609.indd 51
51
2011-06-09
5:38:40
Operation
To Listen in Mono/Stereo
Press the MO/ST button on the remote control.
• Each time you press this button, STEREO or MONO will be selected in turn.
• If you select MONO in an area with weak reception, it will help to reduce noise.
• This function works only with the remote control.
Presetting Radio Stations
You can preset up to 15 FM stations.
E.g.: Setting station FM 89.10 in preset 2.
1. Press the INPUT SELECT button on the remote control to
select FM.
2. Press the TUNING/CH ( .,, ) buttons on the remote control
to select 89.10.
• Refer to step 2 above to tune in automatically and manually.
3. Press the TUNER MEMORY button on the main unit.
• You can also use the TUNER MEMORY button on the
remote control.
• Tuner number will blink on the display.
4. Press the TUNING/CH ( .,, ) buttons on the remote control
to select preset 2.
• You can select from presets 1 to 15.
5. Press the TUNER MEMORY button on the main unit.
• Tuner number will disappear and station 89.10 will be saved
in preset 2.
6. To preset other stations, repeat steps 2 to 5.



To Listen to Preset Station
• Press the TUNING MODE button to select PRESET and press the SELECT ( .,, ) buttons.
52
English
HW-D700_D770S_ELS_0609.indd 52
2011-06-09
5:38:40
04
Operation
About RDS Broadcasting
Using the RDS (Radio Data System) to Receive FM Stations
RDS allows FM stations to send an additional signal along with their
regular program signals. For example, the stations send their station
names, as well as information about what type of program they
broadcast, such as sports or music, etc.
When tuned to an FM station which provides the RDS service, the RDS
indicator lights up on the display.
Description on RDS function
• PTY (Program Type) : Displays the type of program currently being broadcast
• PS NAME (Program Service Name) : Indicates the name of broadcasting station and is composed of
8 characters.
• RT (Radio Text) : Decodes the text broadcast by a station (if any) and is composed of maximum 64
characters.
• CT (Clock Time) : Decodes the real time clock from the FM frequency.Some stations may not
transmit PTY, RT or CT information therefore this may not be displayed in all
cases.
• TA (Traffic Announcement) : When &quot;TA ON&quot; displays, it shows that the traffic announcement is in
progress.
✎ NOTE
 RDS may not operate correctly if the station tuned is not transmitting RDS signal properly or if the
signal strength is weak.
To Show the RDS Signals
You can see the RDS signals the station sends on the display.
Press the RDS DISPLAY button while listening to an FM
station.
• Each time you press the button, the display change to show you the
following information :
PS NAME  RADIO TEXT  CLOCK/TIME  FREQUENCY
• PS (Program Service) : While searching, &lt;PS NAME&gt; appears and
then the station names will be displayed. &lt;NO PS NAME&gt; appears if no
signal is sent.
• RT(RadioText) : while searching, &lt;RADIO TEXT&gt; appears and then text messages the station sends
will be displayed. &lt;NO RT&gt; appears if no signal is sent.
• Frequency : station frequency (non-RDS service)
About characters shown in the display
When the display shows PS,or RT signals,the following characters are used.
• The display window cannot differentiate upper case and lower case letters and always uses upper
case letters.
• The display window cannot show accented letters, &lt;A,&gt; for instance, may stands for accented
&lt;A’s&gt; like &lt;&Agrave;, &Acirc;, &Auml;, &Aacute;, &Aring; and &Atilde;.&gt;
English
HW-D700_D770S_ELS_0609.indd 53
53
2011-06-09
5:38:40
Operation
PTY (Program Type) Indication and PTY-SEARCH Function
One of the advantages of the RDS service is that you can locate a particular kind of program from the
preset channels by specifying the PTY codes.
To search for a program using the PTY codes
Before you start, remember...
• The PTY Search is only applicable to preset stations.
• To stop searching any time during the process, press PTY SEARCH while searching.
• There is a time limit in doing the following steps. If the setting is cancelled before you finish, start
from step 1 again.
• When pressing the buttons on the primary remote control, make sure that you have selected the FM
station using the primary remote control.
1. Press the PTY SEARCH button while listening to an FM station.
2. Press the PTY- or PTY+ button until the PTY code you want
appears on the display.
• The display gives you the PTY codes described to the right.
3. Press the PTY SEARCH button again, while the PTY code selected
in the previous step is still on the display.
• The centre unit searches 29 preset FM stations, stops when it
finds the one you have selected, and tunes in that station.
Display
Program Type
Display
Program Type
NEWS
News including an announced opinion
and report
LIGHT M
Light classical music- Classical music
and instrumental and chorus music
AFFAIRS
Several matters including a current incident,
documentary, discussion and analysis.
CLASSICS
Heavy classical music-Orchestra music,
symphony, chamber music and opera
INFO
Information including weights and measures,
returns and forecast, matters interesting the
customer, medical information, etc.
SPORT
EDUCATE
DRAMA
CULTURE
SCIENCE
Sports
Education
Drama-Radio serial, etc.
Culture-National or local culture including
the religious problem, social science,
language, cinema, etc.
Natural science and technology
OTHER M
Other music - Jazz, R&amp;B country music
WEATHER
Weather
FINANCE
Finance
CHILDREN
SOCIAL
Children’s programmes
Social affairs
RELIGION
Religion
PHONE IN
Phone in
TRAVEL
LEISURE
Travel
Leisure
VARIED
Others-Speech, amusing program
(quiz, game), interview, comedy and
satirical play, etc.
COUNTRY
Country Music
POP M
Pop music
NATION M
National Music
JAZZ
Jazz Music
ROCK M
Rock music
OLDIES
Oldies Music
M.O.R.M
Current contemporary music considered to
be “easy listening.”
FOLK M
Folk Music
54
DOCUMENT
Documentary
English
HW-D700_D770S_ELS_0609.indd 54
2011-06-09
5:38:42
04
Operation
Using an iPod
You can enjoy playback of your iPod using the supplied remote control.
Listening to Music (iPod audio function)
You can play music files stored in the iPod player by connecting it to the AV
receiver.
1. Connect the iPod dock connector to the iPod jack on the AV Receiver.
2. Place the iPod in the dock.
• Your iPod is automatically turned on.
3. Press the INPUT SELECT button on the remote control to select IPOD
AUDIO mode.
4. Press the PLAY button on the remote control to play.
• The AV receiver starts playing from the first track of the iPod player.
5. You can use the remote control to control simple playback functions such as the PLAY, PAUSE,
STOP, SKIP (#,$) buttons.
✎ NOTE
 See page 28 for compatible iPods.
Compatibility depends on the software version of your iPod.
 You can also select iPod by pressing the iPod button on the remote control.
Watching a Movie (iPod video function)
You can play video files stored in the iPod player on a TV by
connecting it to the AV receiver.
1. Connect the iPod dock connector to the iPod jack on the AV
receiver.
2. In the iPod screen, move to Videos &gt; Settings and set the TV
Out option to On.
3. Place the iPod in the dock.
4. Press the INPUT SELECT button on the remote control to select
IPOD VIDEO mode.
5. Set the AV IN option of the TV connected to the AV receiver to
COMPOSITE.
&lt;iPod Screen&gt;
Follow the iPod onscreen guide through the following steps.
6. Press the , buttons on the remote control to select Videos and
press the ENTER button.
7. Press the , buttons on the remote control to select Movies and
press the ENTER button.
English
HW-D700_D770S_ELS_0609.indd 55
55
2011-06-09
5:38:42
Operation
8. Press the , buttons to select the file to play and press the
ENTER button.
• The iPod's video files will be played on the TV screen.
9. You can use the remote control to control simple playback
functions such as the PLAY, PAUSE, STOP, SKIP (#,$)
buttons.
• If you press the PREV button after the playback, the player will
move to the start screen of the current file.
&lt;iPod Screen&gt;
• Press the STOP button to stop playing and return to the list screen.
• Press the RETURN button to return to the previous menu.
✎ NOTE
 Before you can play the video files in the iPod player, you must connect the Audio/Video terminals
of the TV to the receiver using the Composite (A/V) cable.
 See page 28 for compatible iPods.
Compatibility depends on the software version of your iPod.
 When the current file is played to the end, the next file will not be played automatically.
To play the next file, select a file to play in the list screen of the iPod player.
 No other screen than the playback one will appear on the TV screen. Check other screens on the
iPod player.
Convenient Functions
Sleep Timer Function
You can set the time that this unit will shut itself off.
Press the SLEEP button.
• SLEEP : OFF  10M  20M  30M  60M  90M  120M 
150M will be selected in turn.
To check sleep timer
Press the SLEEP button.
• The remaining time before this unit will shut itself off is shown on the
display.
• Pressing the button again changes the sleep time from what you set
previously.
To cancle sleep timer
• Press the SLEEP button until SLEEP OFF appears on the display.
56
English
HW-D700_D770S_ELS_0609.indd 56
2011-06-09
5:38:44
04
Operation
Mute Function
This function is useful when answering a doorbell or telephone call.
Press the MUTE button.
• MUTE appears on the display.
To output sound again
Press the MUTE button again or press the Volume button.
• MUTE will disappear and sound will output.
Adjust the Display
You can adjust the brightness of the display.
Press the DIMMER button.
• Each time you press this button, the brightness changes as follows :
Dark  Bright.
✎ NOTE
 SLEEP, Mute and the Adjust Display functions can only be
operated with the remote control.
Reset Function
When the Power is on,
1. Press the MUTE button.
• MUTE appears on the display.
2. Press the 2 button five times and then press the ENTER button.
• INITIAL : NO appears on the display.
3. Press the ◄ ► buttons to select YES.
• The unit will turn off after 5 seconds.
When the Power is Off,
1. Press and hold the TUNER MEMORY button on the front of your AV
Receiver for longer than 5 seconds.
• POWER LED will blink one time.
✎ NOTE
 Using the RESET function will erase all stored settings.
 Do not use this unless necessary.
English
HW-D700_D770S_ELS_0609.indd 57
57
2011-06-09
5:38:45
Operation
Using Headphones
Use headphones (not supplied) for private listening pleasure.
Connect the headphones to the headphone (PHONES) jack and listen to music.
✎ NOTE
 Do not turn the volume up too high when you use headphones as it may damage your hearing.
Software Upgrade
Samsung may offer upgrades for AV Receiver's firmware in the future.
Please visit Samsung.com or contact the Samsung call centre to
receive information about downloading upgrades and using a USB
drive. Upgrades will be possible by connecting a USB drive to the
USB port located on your AV Receiver.
ONLY FOR
UPDATE
✎ NOTE
 Insert a USB drive containing the firmware upgrade into the USB
port on the back of the main unit.
 Please be careful to not disconnect the power or remove the USB
drive while upgrades are being applied. The main unit will turn off
automatically after completing the firmware upgrade.
When software is upgraded, settings you have made will return to
their default (factory) settings. We recommend you write down your
settings so that you can easily reset them after the upgrade.
 If you failed software upgrade, it is strongly recommended whole USB data format to FAT16 and
retry software upgrade.
 The NTFS USB File System can not be supported.
 Depending on the manufacturer, the USB may not be supported.
ONLY FOR
SERVICE
58
English
HW-D700_D770S_ELS_0609.indd 58
2011-06-09
5:38:46
05
Miscellaneous
1. Press the POWER button to turn on the TV.
2. Press the TV button to set the remote to TV mode.
3. Point the remote control toward the TV.
4. While holding down the POWER button, enter the code corresponding to your brand of TV.
• If there is more than one code listed for your TV in the table, enter one at a time to determine
which code works.
• If the code matches the TV's code, the TV will be turned off.
5. If TV is turned on or off when you press the POWER button of the remote control, the setting is
completed.
• You can use the TV POWER, VOLUME, CHANNEL, MENU and Numeric buttons (0~9).
Miscellaneous
Operating your TV with the Remote Control
✎ NOTE
 The remote control may not work on some brands of TVs. Also, some operations may not be
possible depending on your brand of TV.
 The remote control will work with Samsung TVs by default.
TV Brand Code List
Brand
Code
Brand
Code
Brand
Code
Admiral (M.Wards)
56, 57, 58
Hitachi
15, 18, 50, 59, 69
Realistic
03, 19
A Mark
01, 15
Inkel
45
Sampo
40
Anam
01, 02, 03, 04, 05, 06, 07, 08,
09, 10, 11, 12, 13, 14
JC Penny
56, 59, 67, 86
Samsung
00, 15, 16, 17, 40, 43, 46,
47, 48, 49, 59, 60, 98
AOC
01, 18, 40, 48
Bell &amp; Howell
(M.Wards)
Brocsonic
Candle
JVC
70
KTV
59, 61, 87, 88
57, 58, 81
KEC
03, 15, 40
59, 60
KMC
15
LG (Goldstar)
01, 15, 16, 17, 37, 38, 39, 40, 41,
42, 43, 44
Luxman
18
18
Cetronic
03
Citizen
03, 18, 25
Cinema
97
Classic
03
Concerto
18
Contec
46
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
Sears
15, 18, 19
Sharp
15, 57, 64
Signature 2000
(M.Wards)
57, 58
LXI (Sears)
19, 54, 56, 59, 60, 62, 63, 65, 71
Sony
50, 51, 52, 53, 55
Magnavox
15, 17, 18, 48, 54, 59, 60, 62, 72, 89
Soundesign
03, 40
Marantz
40, 54
Spectricon
01
Matsui
54
SSS
18
MGA
18, 40
Sylvania
18, 40, 48, 54, 59, 60, 62
Coronado
15
Craig
03, 05, 61, 82, 83, 84
Mitsubishi/
MGA
18, 40, 59, 60, 75
Symphonic
61, 95, 96
Croslex
62
MTC
18
Tatung
06
Crown
03
NEC
18, 19, 20, 40, 59, 60
Techwood
18
Curtis Mates
59, 61, 63
Nikei
03
Teknika
03, 15, 18, 25
CXC
03
Onking
03
TMK
18, 40
Onwa
03
Toshiba
19, 57, 63, 71
Daewoo
02, 03, 04, 15, 16, 17, 18, 19, 20,
21, 22, 23, 24, 25, 26, 27, 28, 29,
30, 32, 34, 35, 36, 48, 59, 90
Panasonic
06, 07, 08, 09, 54, 66, 67, 73, 74
Vidtech
18
Daytron
40
Penney
18
Videch
59, 60, 69
Dynasty
03
Philco
03, 15, 17, 18, 48, 54, 59, 62, 69, 90
Wards
15, 17, 18, 40, 48, 54, 62, 72
15, 17, 18, 40, 48, 54,
60, 64
03, 15, 40, 46, 59, 61, 64, 82,
83, 84, 85
Philips
Pioneer
63, 66, 80, 91
Yamaha
18
Fisher
19, 65
Portland
15, 18, 59
York
40
Funai
03
Proton
40
Futuretech
03
Quasar
06, 66, 67
General Electric (GE)
06, 40, 56, 59, 66, 67, 68
Radio Shack
17, 48, 56, 60, 61, 75
40
RCA/Proscan
18, 59, 67, 76, 77, 78, 92, 93, 94
Emerson
Hall Mark
Yupiteru
03
Zenith
58, 79
Zonda
01
Dongyang
03, 54
English
HW-D700_D770S_ELS_0609.indd 59
59
2011-06-09
5:38:48
Miscellaneous
Operating your DVD or BD Player with the Remote Control
1. Press the POWER button to turn on the DVD (BD) player.
2. Press the BD/DVD button on the remote control to set the remote to DVD (BD) mode.
3. Point the remote control toward the DVD (BD).
4. While holding down POWER button, enter the code corresponding to your brand of DVD (BD).
• If there is more than one code listed for your DVD (BD) in the table, enter one at a time to
determine which code works.
• If the code matches the DVD (BD)'s code, the DVD (BD) will be turned off.
5. If DVD (BD) is turned on or off when you press the POWER button of the remote controller, the
setting is completed.
• You can use DVD (BD) POWER, PLAY, PAUSE, STOP, SKIP, MENU and Numeric buttons
(0~9).
✎ NOTE
 The remote control may not work on some brands of DVD.
Also, some operations may not be possible depending on your brand of DVD.
 The remote control will work with Samsung DVD (BD) by default.
DVD Brand Code List
Brand
DENON
DOONOON
DMTECH
FISHER
GE
HARMAN/KARDON
JVC
KENWOOD
LG
MAGNAVOX
MITSUBISHI
Code Number
003, 032
019
017
002
006
012
010, 013
008
001
004
005, 016
Brand
Code Number
ONKYO
OPTIMUS
PANASONIC
PROSCAN
PHILIPS
PIONEER
RCA
SAMSUNG
SANYO
SONY
THETA DIGITAL
004, 014
011
021
006
004, 023
007, 011, 022, 025
006
000, 027
002
015, 020
011
Brand
TOSHIBA
YAMAHA
ZENITH
TAEGWANG
PS2
X-BOX
APEX
Marantz
Code Number
004, 018
009, 033
004, 024
026
028
029
030
031
BD Player Brand Code List
Brand
SAMSUNG
Code Number
000, 001, 002, 003, 004
✎ NOTE
 The remote control will control Samsung BD players only.
60
English
HW-D700_D770S_ELS_0609.indd 60
2011-06-09
5:38:48
06
Other Information
Other Information
Troubleshooting
Before requesting service, please check the following.
Symptom
Check
Remedy
The unit will not turn on.
• Is the power cord plugged into the
outlet?
• Connect the power plug to the
outlet.
A function does not
work when the button is
pressed.
• Is there static electricity in the air?
• Disconnect the power plug and
connect it again.
Sound is not produced.
• Are the speakers and external
components connected properly?
• Is the Mute function on?
• Is the volume set to minimum?
• Is the Speaker Size set incorrectly
to NONE?
• Connect them correctly.
• Press the MUTE button to
cancel the function.
• Adjust the volume.
• Refer to pages 36 to select
LARGE, SMALL or YES.
Picture does not appear
on a TV when the
function is selected.
• Is the external component
connected properly?
• Connect it correctly.
Remote controller does
not work.
• Are the batteries drained?
• Is the distance between remote
control and main unit too great?
• Replace with new batteries.
• Operate at close distance.
The sound from the left/
right channels is
reversed.
• Are the left/right speaker or left/right
input/output cables connected
properly?
• Check the left/right channel and
connect it/them correctly.
Can't receive radio
broadcasts.
• Is FM antenna connected
properly?
• Connect the antenna correctly.
• If the input strength of antenna
signal is weak, install the FM
antenna in a place with good
reception.
There is no sound from
surround speakers.
• Are the surround speakers
connected properly?
• Is SURR (surround) incorrectly set
to NONE in the Speaker Size?
• Is surround mode set to stereo?
• Refer to page 16 to connect
them properly.
• Refer to page 36 to select
LARGE or SMALL.
• Refer to pages 49 ~ 51 to select
proper Surround Mode.
There is no sound from
surround back
speakers
• Are the surround back speakers
connected properly?
• Is SBACK (Surround Back) set to
NONE in the Speaker Size?
• Is Surround Mode set to EX/ES?
• Refer to page 16 to connect
them properly.
• Refer to page 36 to select
LARGE or SMALL.
• Refer to page 42 to set
Surround Mode to EX/ES.
English
HW-D700_D770S_ELS_0609.indd 61
61
2011-06-09
5:38:48
Other Information
Symptom
Check
Remedy
Can't select EX/ES
mode.
• Is SBACK (Surround Back) set to
NONE in the Speaker Size?
• Is the input signal selected
properly?
• Refer to page 36 to select
LARGE or SMALL.
• Use a 7.1 channel external
component.
Can't select Dolby Pro
Logic llx mode.
• Is the input signal selected
properly?
• Only 2 channel signal can
select Dolby Pro Logic IIx
mode. (ex:Dolby Digital, PCM,
2 channel analogue input
signal.)
Can't select NEO:6
mode.
• Is the input signal selected
properly?
• Use PCM and Analogue input
signal.
There is no sound
when playing a DTS
encoded DVD.
• Is Digital input selected?
• Check whether the DVD player
is properly connected and refer
to page 31 to select the digital
input.
Product Protection Function
Heat protection
• The protection function will come on if the main unit or power transformer overheats.
&quot; will appear in the display .
&quot;
This function will come on :
- If speaker terminal is shorted
- If speaker cable is shorted
If there is no problem when you turn the unit on again after turning it off, PROTECTION mark will
disappear on the display and the unit will work properly.
62
English
HW-D700_D770S_ELS_0609.indd 62
2011-06-09
5:38:48
06
Other Information
Auto Calibration Error List
Error No.
Auto Calibration Error Message on OSD
E02 NO MIC
Connect the calibration microphone.
E03 NOISY
Keep quiet during the measurement.
E04 MIC LEVL
The speaker are too close to the microphone.
Install all speakers and the calibration microphone at the proper location.
E05 NO FRONT
Connect the front speaker correctly.
E07 LEVL OVR
Install all speakers and the calibration microphone at the proper location.
E08 DIST OVR
Some speakers are too far from calibration microphone.
Install all speakers and the calibration microphone at the proper location.
E13 TIME OVR
Unplug and re-plug the power cable.
Then, perfrom the measurement again.
E14 CODE ERR
Unplug and re-plug the power cable.
Then, perfrom the measurement again.
English
HW-D700_D770S_ELS_0609.indd 63
63
2011-06-09
5:38:49
Other Information
Specifications
GENERAL
FM TUNER
AMPLIFIER
FREQUENCY
RESPONSE
HDMI
VIDEO OUTPUT
Weight
6.2 kg
Dimensions (W x H x D)
429.2 x 165.1 x 360.6 mm
Operating temperature range
+5&deg;C~+35&deg;C
Operating humidity range
10%~75%
Frequency response
87.5~108.0MHz
Usable sensitivity
12dBf
S/N ratio
MONO/STEREO 55/55dB
Distortion
MONO/STEREO 0.3/0.8%
Stereo separation
30dB
Tuner output level
1kHz, 75kHz Dev
Rated output
20Hz~20kHz/THD = 0.9%
Front speaker (left+right)
6 Ω 120W/CH
Centre speaker
6 Ω 120W/CH
Surround speaker (left+right)
6 Ω 120W/CH
Surround back speaker (left+right)
6 Ω 120W/CH
Subwoofer speaker
8 Ω 150W/CH
Input sensitivity/impedance
450mV/47kΩ
S/N ratio (analogue input)
80dB
Separation (1kHz)
60dB
Analogue input
20Hz~20kHz(&plusmn;3dB)
Digital input/96kHz PCM
20Hz ~44kHz(&plusmn;3dB)
Input
Compatible 1080p
Output
Compatible 1080p
TV format
NTSC/PAL
Input level/impedance
1Vp-p/75 Ω
Output level/impedance
1Vp-p/75 Ω
Video frequency response
5Hz to 10kHz(-3dB)
S/N Ratio
60dB
* S/N Ratio, Distortion, Separation and Usable sensitivity are based on measurement using AES (Audio
Engineering Society) guidelines.
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For the power supply and Power Consumption, refer to the label attached to the product.
64
English
HW-D700_D770S_ELS_0609.indd 64
2011-06-09
5:38:49
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.
Area
` North America
Canada
Mexico
U.S.A
Contact Centre 
Web Site
1-800-SAMSUNG (726-7864)
01-800-SAMSUNG (726-7864)
1-800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
0800-333-3733
0800-124-421 / 4004-0000
800-SAMSUNG (726-7864)
01-8000112112
0-800-507-7267
1-800-751-2676
1-800-10-7267
800-6225
1-800-299-0013
800-7919267
1-800-234-7267
00-1800-5077267
800-7267
0-800-777-08
1-800-682-3180
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
1-800-SAMSUNG (726-7864)
www.samsung.com
0-800-100-5303
www.samsung.com
42 27 5755
0810 - SAMSUNG (7267864,
€ 0.07/min)
-
` Latin America
Argentine
Brazil
Chile
Colombia
Costa Rica
Dominica
Ecuador
El Salvador
Guatemala
Honduras
Jamaica
Nicaragua
Panama
Peru
Puerto Rico
Trinidad &amp;
Tobago
Venezuela
Austria
Belgium
02-201-24-18
Bosnia
Bulgaria
Croatia
05 133 1999
07001 33 11
062 SAMSUNG (062 726 7864)
800-SAMSUNG (800-726786)
Samsung Zrt., česk&aacute; organizačn&iacute;
složka, Oasis Florenc, Sokolovsk&aacute;394/17, 180 00, Praha 8
70 70 19 70
030 - 6227 515
01 48 63 00 00
01805 - SAMSUNG (726-7864
€ 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
+381 0113216899
261 03 710
023 207 777
020 405 888
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
815-56 480
0 801 1SAMSUNG (172678)
/ 022-607-93-33
80820-SAMSUNG (726-7864)
1. 08010 SAMSUNG (72678) doar din reţeaua Romtelecom,
tarif local
2. 021.206.01.10 - din orice
reţea, tarif normal
Czech
Denmark
Finland
France
Germany
Hungary
Italia
Kosovo
Luxemburg
Macedonia
Montenegro
Netherlands
Norway
Poland
Portugal
Rumania
HW-D700_D770S_ELS_0609.indd 65
Slovakia
Spain
Sweden
Contact Centre 
0700 Samsung (0700 726
7864)
0800-SAMSUNG (726-7864)
902-1-SAMSUNG (902 172 678)
0771 726 7864 (SAMSUNG)
Switzerland
0848-SAMSUNG (7267864,
CHF 0.08/min)
U.K
Eire
Lithuania
Latvia
Estonia
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
Uzbekistan
Kyrgyzstan
Tadjikistan
Ukraine
0-800-502-000
www.samsung.com
Belarus
Moldova
810-800-500-55-500
00-800-500-55-500
www.samsung.com/
be (Dutch)
www.samsung.com/
be_fr (French)
www.samsung.com
www.samsung.com
` Asia Pacific
www.samsung.com
Russia
Georgia
Armenia
Azerbaijan
Kazakhstan
Australia
New Zealand
China
1300 362 603
0800 SAMSUNG (0800 726 786)
400-810-5858 / 010-6475 1880
Hong Kong
(852) 3698 4698
India
Indonesia
www.samsung.com
www.samsung.com
www.samsung.com
Japan
Malaysia
www.samsung.com
Philippines
www.samsung.com
www.samsung.com
www.samsung.com
-
Singapore
Thailand
Taiwan
Vietnam
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/ch
www.samsung.com/
ch_fr/(French)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
` CIS
8-800-555-55-55
8-800-555-555
0-800-05-555
088-55-55-555
8-10-800-500-55-500
(GSM: 7799)
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
` Europe
Albania
Area
Serbia
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.ua
www.samsung.com/
ua_ru
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com/
hk_en/
3030 8282 / 1800 110011 /
1800 3000 8282 / 1800 266 8282
0800-112-8888 /
021-5699-7777
0120-327-527
1800-88-9999
1-800-10-SAMSUNG(726-7864) /
1-800-3-SAMSUNG(726-7864) /
1-800-8-SAMSUNG(726-7864) /
02-5805777
1800-SAMSUNG (726-7864)
1800-29-3232 / 02-689-3232
0800-329-999
1 800 588 889
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
8000-4726
08000-726786
800-22273
080 100 2255
800-SAMSUNG (726-7864)
9200-21230
444 77 11
800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
0800-SAMSUNG (726-7864)
0860-SAMSUNG (726-7864 )
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
` Middle East
Bahrain
Egypt
Jordan
Morocco
Oman
Saudi Arabia
Turkey
U.A.E
` Africa
Nigeria
South Africa
2011-06-09
5:38:49
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not
be disposed of with other household waste at the end of their working life. Where marked, the chemical
symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference
levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm
to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of
waste and recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical &amp; Electronic
Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these
items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office,
for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
HW-D700_D770S_ELS_0609.indd 66
2011-06-09
5:38:49
">

Bonjour ! Je suis un chatbot IA spécialement formé pour vous aider avec le Samsung HW-D770S Manuel de l'utilisateur. J'ai soigneusement étudié le document et je peux vous aider à trouver les informations dont vous avez besoin ou expliquer le contenu en termes clairs et simples. Que vous recherchiez des conseils sur des fonctionnalités spécifiques, des étapes de dépannage ou une utilisation générale, n'hésitez pas à poser vos questions. Plus vous fournissez de détails sur vos préoccupations ou besoins, plus je pourrai vous aider avec précision et efficacité.

Assistant en train d''écrire

L''assistant n''est plus disponible. Veuillez réessayer plus tard.

Il semble que vous ayez accédé à un document rédigé en plusieurs langues, dont une qui n''est pas votre langue maternelle. Vous pouvez utiliser les liens suivants pour masquer temporairement les pages sans la langue que vous préférez.