STGB7NC60HD,
STGF7NC60HD, STGP7NC60HD
N-channel 14 A, 600 V, very fast IGBT with Ultrafast diode
Datasheet
−
production data
Features
■
■
■
■
■
Low on-voltage drop (V
CE(sat)
)
Off losses include tail current
Losses include diode recovery energy
High frequency operation up to 70 kHz
Very soft ultra fast recovery anti parallel diode
Applications
■
■
■
High frequency inverters
SMPS and PFC in both hard switch and resonant topologies
Motor drivers
Description
These devices are very fast IGBT developed using advanced PowerMESH™ technology. This process guarantees an excellent trade-off between switching performance and low on-state behavior. These devices are well-suited for resonant or soft-switching applications.
TAB
1
2
3
I²PAK (TO-262)
TAB
TO-220
1
2
3
Figure 1.
Internal schematic diagram
C (2, TAB)
1
2
3
TO-220FP
G (1)
TAB
1
3
D²PAK (TO-263)
E (3)
Table 1.
Device summary
Order codes
STGB7NC60HD-1
STGB7NC60HDT4
STGF7NC60HD
STGP7NC60HD
Markings
GB7NC60HD
GF7NC60HD
GP7NC60HD
Packages
I²PAK (TO-262)
D²PAK (TO-26 3 )
TO-220FP
TO-220
June 2012
This is information on a product in full production.
Doc ID 10042 Rev 10
Packaging
Tube
Tape and reel
Tube
Tube
1/22 www.st.com
22
5
6
3
4
1
2
Contents
Contents
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1
Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2
Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD Electrical ratings
Table 2.
Absolute maximum ratings
Symbol Parameter
V
CES
V
ECR
V
GE
I
C
I
C
I
CM
(2)
I
F
P
TOT
Collector-emitter voltage (V
Emitter-collector voltage
GS
= 0)
Gate-emitter voltage
Collector current (continuous) at T
C
= 25 °C
(1)
Collector current (continuous) at T
C
= 100 °C
(1)
Collector current (pulsed)
Diode RMS forward current at T
C
= 25°C
Total dissipation at T
C
= 25°C
Derating factor
V
ISO
Insulation withstand voltage A.C. (t = 1 sec;
T
C
= 25°C)
Storage temperature T stg
T j
Operating junction temperature
1.
Calculated according to the iterative formula:
Value
I
2
PAK, D
2
PAK,
TO-220
TO-220FP
600
20
±20
25
14
80
0.64
--
50
20
– 55 to 150
10
6
25
0.20
2500
Unit
A
A
A
V
A
V
V
W
W/°C
V
°C
I
C
(
T
C
)
= -------------------------------------------------------------------------------------------------------
R thj – c
V
T
CE sat ) ( max
–
)
T
C
T j max )
I
C
( T
C
) )
2.
Pulse width limited by maximum junction temperature and turn-off within RBSOA.
Table 3.
Thermal data
Symbol Parameter
R thJC
R thJA
Thermal resistance junction-case
Thermal resistance junction-ambient
Value
I
2
PAK, D
2
PAK,
TO-220
1.56
62.5
TO-220FP
5.0
Unit
°C/W
°C/W
Doc ID 10042 Rev 10 3 /22
Electrical characteristics STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
4/22
T
CASE
= 25°C unless otherwise specified.
Table 4.
Symbol
Electrical characteristics
Parameter Test conditions
V
(BR)CES
Collector-emitter breakdown voltage
V
I
I
CES
GES
GE(th)
V
CE(sat)
I
C
= 1 mA, V
GE
= 0
Collector cut-off current
(V
GE
= 0)
V
CE
= 600 V
V
CE
= 600 V, T
C
= 125 °C
Gate-emitter leakage current (V
CE
= 0)
V
GE
= ± 20 V
Gate threshold voltage V
CE
= V
GE
, I
C
= 250 µA
Collector-emitter saturation voltage
V
GE
= 15V, I
C
= 7 A
V
GE
= 15V, I
C
= 7 A, T
C
= 125°C
Min.
Typ.
Max.
Unit
600
3 .75
10
1
±100 nA
1.85
1.7
5.75
2.5
V
µA mA
V
V
V
Table 5.
Symbol
Dynamic
Parameter Test conditions g fs
(1)
Forward transconductance
V
CE
= 15 V
,
I
C
= 7 A
C ies
C oes
Input capacitance
Output capacitance V
CE
= 25 V, f = 1 MHz,
V
GE
= 0
C res
Reverse transfer capacitance
Q g
Q ge
Q gc
Total gate charge
Gate-emitter charge
Gate-collector charge
V
V
CE
GE
= 3 90 V, I
= 15 V
C
= 7 A,
I
CL
Turn-off SOA minimum current
V
R clamp
G
= 480 V
,
Tj =150°C
= 10 Ω, V
GE
= 15 V
1.
Pulsed: Pulse duration= 3 00 µs, duty cycle 1.5%
Min.
Typ.
Max.
Unit
50
4.
3 0
720
81
17
3 5
7
16
48
S pF pF pF nC nC nC
A
Table 6.
Symbol t d(on) t r
(di/dt) on t d(on) t r
(di/dt) on
Switching on
Parameter
Turn-on delay time
Current rise time
Turn-on current slope
Turn-on delay time
Current rise time
Turn-on current slope
Test conditions
V
CC
= 3 90 V, I
C
= 7 A
R
G
= 10
Ω
, V
GE
= 15V
(see Figure 21 )
V
CC
= 3 90 V, I
C
= 7 A
R
G
= 10 Ω , V
GE
= 15V,
Tj = 125°C (see
Figure 21 )
Min.
Typ.
Max.
Unit
-
18.5
8.5
1060
18.5
7
1000
ns ns
A/µs ns ns
A/µs
Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD Electrical characteristics
Table 7.
Symbol
Switching off
Parameter t r
(V off
) Off voltage rise time t d
( off
) Turn-off delay time t f
Current fall time t r
(V off
) Off voltage rise time
Turn-off delay time t d
( off
) t f
Current fall time
Test conditions
V
CC
= 3 90 V, I
C
= 7 A,
R
G
= 10 Ω , V
GE
= 15 V
V
CC
= 3 90 V, I
C
= 7 A,
R
G
= 10
Ω
, V
GE
= 15 V
Tj = 125 °C
Min.
Typ.
Max.
Unit
-
27
72
60
56
116
105
ns ns ns ns ns ns
Table 8.
Switching energy
Symbol Parameter Test conditions Min.
Typ.
Max Unit
Eon
(1)
E off
(2)
E ts
Eon
(1)
E off
(2)
E ts
Turn-on switching losses
Turn-off switching loss
Total switching loss
Turn-on switching losses
Turn-off switching loss
Total switching loss
V
R
CC
G
R
G
= 3 90 V, I
= 10 Ω , V
V
CC
= 3 90 V, I
= 10 Ω , V
GE
Tj = 125°C
C
GE
= 7 A
= 15 V,
C
= 7 A
= 15 V,
-
95
115
210
140
215
3 55
125
150
275
1.
Eon is the turn-on losses when a typical diode is used in the test circuit. If the IGBT is offered in a package with a co-pack diode, the co-pack diode is used as external diode. IGBTs and diode are at the same temperature (25°C and 125°C).
2.
Turn-off losses include also the tail of the collector current.
µJ
µJ
µJ
µJ
µJ
µJ t rr t a
Q rr
I rrm
S t rr t a
Q rr
I rrm
S
Table 9.
Symbol
V f
Collector-emitter diode
Parameter
Forward on-voltage
Reverse recovery time
Reverse recovery charge
Reverse recovery current
Softness factor of the diode
Reverse recovery time
Reverse recovery charge
Reverse recovery current
Softness factor of the diode
If =
If =
3
3
Test conditions
.5 A
.5 A, Tj = 125 °C
If = 7 A, V
R
= 40 V, di/dt = 100 A/µs
If = 7 A, V
R
= 40 V,
T j
= 125 °C, di/dt = 100 A/µs
Min.
Typ.
Max.
Unit
1.9
-
1.
3
1.1
61
3 4
98
3 .2
0.79
3 7
22
40
2.1
0.68
V
V ns ns nC
A ns ns nC
A
Doc ID 10042 Rev 10 5/22
Electrical characteristics STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
2.1 Electrical characteristics (curves)
Figure 2.
Output characteristics Figure 3.
Transfer characteristics
Figure 4.
Transconductance Figure 5.
Collector-emitter on voltage vs. temperature
Figure 6.
Collector-emitter on voltage vs. collector current
Figure 7.
Normalized gate threshold vs. temperature
6/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD Electrical characteristics
Figure 8.
Normalized breakdown voltage vs temperature
Figure 9.
Gate charge vs. gate-emitter voltage
Figure 10.
Capacitance variations Figure 11.
Total switching losses vs. temperature
Figure 12.
Total switching losses vs. gate resistance
Figure 13.
Total switching losses vs collector current
Doc ID 10042 Rev 10 7/22
Electrical characteristics
Figure 14.
Emitter-collector diode characteristics
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Figure 15.
Turn-off SOA
Figure 16.
Thermal impedance for I
2
PAK,
D
2
PAK and TO-220
Figure 17.
Thermal impedance for TO-220FP
8/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Figure 18.
I
C
vs. frequency
Electrical characteristics
For a fast IGBT suitable for high frequency applications, the typical collector current vs. maximum operating frequency curve is reported. That frequency is defined as follows:
Equation 1
f
MAX
= (P
D
- P
C
) / (E
ON
+ E
OFF
)
The maximum power dissipation is limited by maximum junction to case thermal resistance:
Equation 2
P
D
=
Δ
T / R
THJ-C considering
Δ
T = T
J
- T
C
= 125 °C- 75 °C = 50°C
The conduction losses are:
Equation 3
P
C
= I
C
* V
CE(SAT)
*
δ with 50% of duty cycle, V
CE(sat)
typical value T
C
= 125°C.
Power dissipation during ON & OFF commutations is due to the switching frequency:
Equation 4
P
SW
= (E
ON
+ E
OFF
) * freq.
Typical values T
V
GE
= 15 V, R
G
C
= 125°C for switching losses are used (test conditions: V
CE
= 3 90 V,
= 3 .
3
Ω
). Furthermore, diode recovery energy is included in the E
ON
, while the tail of the collector current is included in the E
OFF
measurements.
Doc ID 10042 Rev 10 9/22
Test circuits STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Figure 19.
Test circuit for inductive load switching
Figure 20.
Gate charge test circuit
Figure 21.
Switching waveform
V
CE
V
G
I C
Td(on)
Ton
Tr(Ion)
90 %
10 %
Tr(Voff)
Tcro ss
Td(off)
Toff
Tf
90 %
10 %
90 %
10 %
AM01505v1
Figure 22.
Diode recovery time waveform di/dt Q rr
I
F t a t rr t b
I
RRM
I
RRM t
AM01506v1 dv/dt
V
F
AM01507v1
10/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
4 Package mechanical data
Package mechanical data b1 c c2
D e
A
A1 b e1
E
L
L1
L2
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK
®
packages, depending on their level of environmental compliance. ECOPACK
® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark.
Table 10.
I²PAK (TO-262) mechanical data
Dim.
mm.
Typ.
Min.
4.40
2.40
0.61
1.14
0.49
1.2
3
8.95
2.40
4.95
10
1 3
3 .50
1.27
Max.
4.60
2.72
0.88
1.70
0.70
1.
3 2
9.
3 5
2.70
5.15
10.40
14
3 .9
3
1.40
Doc ID 10042 Rev 10 11/22
Package mechanical data
Figure 23.
I²PAK (TO-262) drawing
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
00049 8 2_Rev_H
12/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD e e1
H
J1
L
L1
L2
R
V2 c c2
D
D1
E
E1
A
A1 b b2
Table 11.
D²PAK (TO-263) mechanical data
Dim.
Min.
4.40
0.0
3
0.70
1.14
0.45
1.2
3
8.95
7.50
10
8.50
4.88
15
2.49
2.29
1.27
1.
3 0
0° mm
Typ.
2.54
0.4
Package mechanical data
Max.
4.60
0.2
3
0.9
3
1.70
0.60
1.
3 6
9.
3 5
10.40
5.28
15.85
2.69
2.79
1.40
1.75
8°
Doc ID 10042 Rev 10 1 3 /22
Package mechanical data
Figure 24.
D²PAK (TO-263) drawing
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
0079457_T
Figure 25.
D²PAK footprint
(a)
16.90
12.20
9.75
14/22 a.
All dimensions are in millimeters
Doc ID 10042 Rev 10
3.50
1.60
5.0
8
Footprint
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
F
F1
F2
G
G1
H
A
B
D
E
L5
L6
L7
Dia
L2
L 3
L4
Table 12.
TO-220FP mechanical data
Dim.
Min.
0.75
1.15
1.15
4.95
2.4
10
4.4
2.5
2.5
0.45
28.6
9.8
2.9
15.9
9
3 mm
Typ.
16
Package mechanical data
Max.
1
1.70
1.70
5.2
2.7
10.4
4.6
2.7
2.75
0.7
3 0.6
10.6
3 .6
16.4
9.
3
3 .2
Doc ID 10042 Rev 10 15/22
Package mechanical data
Figure 26.
TO-220FP drawing
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
16/22 Doc ID 10042 Rev 10
7012510_Rev_K_B
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
D
D1
E e e1
F
H1
J1
L
A b b1 c
Table 13.
TO-220 type A mechanical data
Dim.
Min.
4.40
0.61
1.14
0.48
15.25
L1
L20
L 3 0
∅
P
Q
10
2.40
4.95
1.2
3
6.20
2.40
1 3
3 .50
3 .75
2.65
mm
Typ.
1.27
16.40
28.90
Package mechanical data
3 .85
2.95
Max.
4.60
0.88
1.70
0.70
15.75
10.40
2.70
5.15
1.
3 2
6.60
2.72
14
3 .9
3
Doc ID 10042 Rev 10 17/22
Package mechanical data
Figure 27.
TO-220 type A drawing
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
00159 88 _typeA_Rev_ S
18/22 Doc ID 10042 Rev 10
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD Packaging mechanical data
A0
B0
D
D1
E
F
K0
P0
P1
P2
R
T
W
Table 14.
D²PAK (TO-263) tape and reel mechanical data
Tape mm
Dim.
Dim.
Min.
10.5
15.7
1.5
1.59
1.65
11.4
4.8
3 .9
11.9
1.9
50
0.25
2 3 .7
Max.
11.6
5.0
4.1
12.1
2.1
10.7
15.9
1.6
1.61
1.85
0.
3 5
24.
3
C
D
G
A
B
N
T
Min.
1.5
12.8
20.2
24.4
100
Base qty
Bulk qty
Reel mm
Max.
33 0
1 3 .2
26.4
3 0.4
1000
1000
Doc ID 10042 Rev 10 19/22
Packaging mechanical data
Figure 28.
Tape
T
Top cover t a pe
K0
B0
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
10 pitche s c u m u l a tive toler a nce on t a pe +/- 0.2 mm
P0 D P2
F
E
W
A0 P1
U s er direction of feed
D1
R
20/22
Figure 29.
Reel
REEL DIMEN S ION S
A
U s er direction of feed
Bending r a di us
AM0 88 52v2
T
D
B
40mm min.
Acce ss hole
At s l ot loc a tion
C
N
F u ll r a di us
Doc ID 10042 Rev 10
T a pe s lot in core for t a pe s t a rt 25 mm min.
width
G me asu red a t h ub
AM0 88 51v2
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Table 15.
Document revision history
Date Revision
07-Jun-2004
19-Aug-2004
17-Sep-2004
09-Nov-2004
19-Jan-2005
09-Jun-2005
27-Jun-2012
7
8
9
4
5
6
10
Changes
Stylesheet update. No content change.
Complete version
Figure 14 has been added
Final datasheet
Datasheet updated
Modified title
Inserted commercial type STGB7NC60HD.
Minor text changes.
Revision history
Doc ID 10042 Rev 10 21/22
STGB7NC60HD, STGF7NC60HD, STGP7NC60HD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
22/22 Doc ID 10042 Rev 10
