STMicroelectronics TS4994FC Datasheet
Διαφήμιση
Διαφήμιση
TS4994FC
1.2 W differential input/output audio power amplifier with selectable standby
Features
■
■
■
■
■
■
■
■
■
■
■
Differential inputs
Near-zero pop & click
100dB PSRR @ 217Hz with grounded inputs
Operating range from V
CC
= 2.5V to 5.5V
1.2W rail-to-rail output power @ V
CC
THD = 1%, F = 1kHz, with 8 Ω load
= 5V,
90dB CMRR @ 217Hz
Ultra-low consumption in standby mode (10nA)
Selectable standby mode (active low or active high)
Ultra fast startup time: 15ms typ.
Available in 9-bump flip-chip (300mm bump diameter)
Lead-free package
Description
The TS4994 is an audio power amplifier capable of delivering 1W of continuous RMS output power into an 8
Ω
load @ 5V. Due to its differential inputs, it exhibits outstanding noise immunity.
An external standby mode control reduces the supply current to less than 10nA. An STBY
MODE pin allows the standby to be active HIGH or LOW. An internal thermal shutdown protection is also provided, making the device capable of sustaining short-circuits.
Order codes
Part number Temperature range Package
TS4994EIJT - Flip-chip (9 bumps)
The device is equipped with common mode feedback circuitry allowing outputs to be always biased at V
CC mode voltage.
/2 regardless of the input common
The TS4994 is designed for high quality audio applications such as mobile phones and requires few external components.
Applications
■
■
■
■
Mobile phones (cellular / cordless)
Laptop / notebook computers
PDAs
Portable audio devices
Packaging Marking
TS4994EIKJT
TS4994EIJT
-40°C, +85°C
FC9 with back coating
Lead free flip-chip9
Tape & reel
A94
A94
December 2006 Rev 2 1/35 www.st.com
35
Contents
Contents
TS4994FC
Application component information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 4
Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Differential configuration principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Gain in typical application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Common mode feedback loop limitations . . . . . . . . . . . . . . . . . . . . . . . . . 23
Low and high frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Calculating the influence of mismatching on PSRR performance . . . . . . 25
Power dissipation and efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
WU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Single-ended input configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2/35
TS4994FC Application component information
Components
C s
C b
R feed
R
C in in
Functional description
Supply bypass capacitor that provides power supply filtering.
Bypass capacitor that provides half supply filtering.
Feedback resistor that sets the closed loop gain in conjunction with R in
A
V
= closed loop gain = R feed
/R in
.
Inverting input resistor that sets the closed loop gain in conjunction with R feed
.
Optional input capacitor making a high pass filter together with R in
(F
CL
= 1/(2 π R in
C in
).
.
Figure 1.
Typical application
GND
Diff. input -
Cin1
Rin1
220nF
Cin2
20k
Rin2
20k
Optional +
Cb
1u
GND
VCC
+
Cs
1u
Rfeed1
20k
2
VCC
GND
3
1
8
Vin-
Vin+
Bypass
Mode
9
Stdby
4
-
+
Bias
Standby
GND
6
GND
Rfeed2
20k
TS4994IJ
Vo+ 5
Vo-
7
8 Ohms
GND VCC GND VCC
3/35
Absolute maximum ratings and operating conditions
2
TS4994FC
Absolute maximum ratings and operating conditions
Table 1.
Symbol
V
CC
V i
T oper
T stg
T j
R thja
P diss
ESD
Absolute maximum ratings
Parameter
Supply voltage
(1)
Input voltage
(2)
Operating free air temperature range
Storage temperature
Maximum junction temperature
Thermal resistance junction to ambient
(3)
Power dissipation
Human body model
Machine model
Latch-up immunity
Lead temperature (soldering, 10sec)
1.
All voltage values are measured with respect to the ground pin.
2.
The magnitude of the input signal must never exceed V
CC
+ 0.3V / GND - 0.3V.
3.
The device is protected by a thermal shutdown active at 150°C.
Value
6
GND to V
CC
-40 to + 85
-65 to +150
150
250 internally limited
2
200
200
260
Table 2.
Symbol
Operating conditions
Parameter Value Unit
V
CC
Supply voltage 2.5 to 5.5
V
SM
Standby mode voltage input:
Standby active LOW
Standby active HIGH
V
SM
=GND
V
SM
=V
CC
V
STBY
T
SD
R
L
R thja
Standby voltage input:
Device ON (V
SM
Device OFF (V
SM
= GND) or device OFF (V
SM
= GND) or device ON (V
SM
= V
CC
)
= V
CC
)
Thermal shutdown temperature
Load resistor
Thermal resistance junction to ambient
1.5
≤
GND
≤
V
STBY
V
STBY
≤
CC
0.4
(1)
150
≥ 4
100
1.
The minimum current consumption (I
STBY temperature range.
) is guaranteed when V
STBY
= GND or V
CC
(i.e. supply rails) for the whole
V
V
V
°C
Ω
°C/W
Unit
V
V
°C
°C
°C
°C/W
W kV
V mA
°C
4/35
TS4994FC Electrical characteristics
Table 3.
Electrical characteristics for V
CC specified)
= +5V, GND = 0V, T amb
= 25°C (unless otherwise
Parameter Min.
Typ.
Max.
Unit Symbol
I
CC
Supply current
No input signal, no load
4 7
I
STBY
V
THD + N
PSRR
CMRR
SNR
GBP t
V
P
ICM
V oo out
N
WU
IG
Standby current
No input signal, V
STBY
= V
SM
No input signal, V
STBY
= V
SM
= GND, R
= V
CC
, R
L
L
= 8 Ω
= 8 Ω
Differential output offset voltage
No input signal, R
L
= 8 Ω
Input common mode voltage
CMRR ≤ -60dB
Output power
THD = 1% Max, F= 1kHz, R
L
= 8 Ω
Total harmonic distortion + noise
P out
= 850mW rms, A
V
= 1, 20Hz
≤
F
≤
L
= 8
Ω
Power supply rejection ratio with inputs grounded
(1)
F = 217Hz, R = 8 Ω, A
V
= 1, C in
= 4.7
μ F, C b
=1 μ F
V ripple
= 200mV
PP
Common mode rejection ratio
F = 217Hz, R
L
= 8 Ω, A
V
= 1, C in
= 4.7
μ F, C b
=1 μ F
V ic
= 200mV
PP
Signal-to-noise ratio (A-weighted filter, A
V
= 2.5)
R
L
= 8 Ω, THD +N < 0.7%, 20Hz ≤ F ≤
Gain bandwidth product
R
L
= 8 Ω
Output voltage noise, 20Hz F ≤
L
= 8 Ω
Unweighted, A
V
= 1
A-weighted, A
V
= 1
Unweighted, A
V
= 2.5
A-weighted, A
V
= 2.5
Unweighted, A
V
= 7.5
A-weighted, A
V
= 7.5
Unweighted, Standby
A-weighted, Standby
Wake-up time
(2)
C b
=1 μ F
0.6
0.8
10
0.1
1.2
0.5
100
90
100
2
6
5.5
12
10.5
33
28
1.5
1
15
V
1000
10
CC
- 0.9
1.
Dynamic measurements - 20*log(rms(V out
)/rms (V ripple
)). V ripple
is the super-imposed sinus signal relative to V
CC
.
2.
Transition time from standby mode to fully operational amplifier.
mA nA mV
V
W
% dB dB dB
MHz
μ V
RMS ms
5/35
Electrical characteristics TS4994FC
Table 4.
Electrical characteristics for V
CC
= +3.3V (all electrical values are guaranteed with correlation measurements at 2.6V and 5V), GND = 0V, T amb
= 25°C (unless otherwise specified)
Parameter Min.
Typ.
Max.
Unit Symbol
I
CC
Supply current no input signal, no load 3 7
I
STBY
V
V
P
V oo
ICM out
THD + N
PSRR
SNR
GBP
N
IG
CMRR
Standby current
No input signal, V
STBY
= V
SM
No input signal, V
STBY
= V
SM
= GND, R
= V
CC
, R
L
L
= 8 Ω
= 8 Ω
Differential output offset voltage
No input signal, R
L
= 8 Ω
Input common mode voltage
CMRR ≤ -60dB
Output power
THD = 1% max, F= 1kHz, R
L
= 8 Ω
Total harmonic distortion + noise
P out
= 300mW rms, A
V
= 1, 20Hz ≤ F ≤
L
= 8 Ω
Power supply rejection ratio with inputs grounded
(1)
F = 217Hz, R = 8 Ω, A
V
= 1, C in
= 4.7
μ F, C b
=1 μ F
V ripple
= 200mV
PP
Common mode rejection ratio
F = 217Hz, R
L
= 8 Ω, A
V
= 1, C in
= 4.7
μ F, C b
=1 μ F
V ic
= 200mV
PP
Signal-to-noise ratio (A-weighted filter, A
V
= 2.5)
R
L
= 8 Ω, THD +N < 0.7%, 20Hz ≤ F ≤
Gain bandwidth product
R
L
= 8 Ω
Output voltage noise, 20Hz F ≤
L
= 8 Ω
Unweighted, A
V
= 1
A-weighted, A
V
= 1
Unweighted, A
V
= 2.5
A-weighted, A
V
= 2.5
Unweighted, A
V
= 7.5
A-weighted, A
V
= 7.5
Unweighted, Standby
A-weighted, Standby
0.6
300
10
0.1
500
0.5
100
90
100
2
6
5.5
12
10.5
33
28
1.5
1
V
1000
10
CC
- 0.9
t
WU
Wake-up time
(2)
C b
=1 μ F
15
1.
Dynamic measurements - 20*log(rms(V out
)/rms (V ripple
)). V ripple
is the super-imposed sinus signal relative to V
CC
.
2.
Transition time from standby mode to fully operational amplifier.
mA nA mV
V mW
% dB dB dB
MHz
μ V
RMS ms
6/35
TS4994FC Electrical characteristics
Table 5.
Electrical characteristics for V
CC specified)
= +2.6V, GND = 0V, T amb
= 25°C (unless otherwise
Parameter Min.
Typ.
Max.
Unit Symbol
I
CC
Supply current
No input signal, no load
3 7
I
STBY
THD + N
PSRR t
V
V
P oo
ICM out
IG
CMRR
SNR
GBP
V
N
WU
Standby current
No input signal, V
STBY
= V
SM
No input signal, V
STBY
= V
SM
= GND, R
= V
CC
, R
L
L
= 8 Ω
= 8 Ω
Differential output offset voltage
No input signal, R
L
= 8 Ω
Input common mode voltage
CMRR ≤
Output power
THD = 1% max, F= 1kHz, R
L
= 8 Ω
Total harmonic distortion + noise
P out
= 225mW rms, A
V
= 1, 20Hz F ≤
L
= 8 Ω
Power supply rejection ratio with inputs grounded
(1)
F = 217Hz, R = 8
Ω,
A
V
= 1, C in
= 4.7
μ
F, C b
=1
μ
F
V ripple
= 200mV
PP
Common mode rejection ratio
F = 217Hz, R
L
= 8 Ω, A
V
= 1, C in
= 4.7
μ F, C
V ic
= 200mV
PP b
=1 μ F
Signal-to-noise ratio (A-weighted filter, A
V
= 2.5)
R
L
= 8
Ω,
THD +N < 0.7%, 20Hz F 20kHz
Gain bandwidth product
R
L
= 8 Ω
Output voltage noise, 20Hz F ≤
L
= 8 Ω
Unweighted, A
V
= 1
A-weighted, A
V
= 1
Unweighted, A
V
= 2.5
A-weighted, A
V
= 2.5
Unweighted, A
V
= 7.5
A-weighted, A
V
= 7.5
Unweighted, Standby
A-weighted, Standby
Wake-up time
(2)
C b
=1 μ F
0.6
200
10
0.1
300
0.5
100
90
100
2
6
5.5
12
10.5
33
28
1.5
1
15
V
1000
10
CC
- 0.9
1.
Dynamic measurements - 20*log(rms(V out
)/rms (V ripple
)). V ripple
is the super-imposed sinus signal relative to V
CC
.
2.
Transition time from standby mode to fully operational amplifier.
mA nA mV
V mW
% dB dB dB
MHz
μ
V
RMS ms
7/35
Electrical characteristics TS4994FC
Figure 2.
Current consumption vs. power supply voltage
Figure 3.
Current consumption vs. standby voltage
4.0
3.5
No load
Tamb=25
°
C
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0 1 2 3
Power Supply Voltage (V)
4 5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0
Standby mode=0V
Standby mode=5V
1 2 3
Standby Voltage (V)
Vcc = 5V
No load
Tamb=25 ° C
4 5
Figure 4.
Current consumption vs. standby voltage
Figure 5.
Current consumption vs. standby voltage
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0.0
Standby mode=0V
Standby mode=3.3V
0.6
1.2
1.8
Standby Voltage (V)
2.4
Vcc = 3.3V
No load
Tamb=25
°
C
3.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
0.0
Standby mode=0V
Standby mode=2.6V
0.6
1.2
1.8
Standby Voltage (V)
Vcc = 2.6V
No load
Tamb=25
°
C
2.4
Figure 6.
Differential DC output voltage vs.
common mode input voltage
Figure 7.
Power dissipation vs. output power
1000
100
Av = 1
Tamb = 25 ° C
Vcc=2.5V
10
1
0.1
Vcc=3.3V
Vcc=5V
0.01
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Common Mode Input Voltage (V)
0.6
0.4
0.2
0.0
0.0
1.4
1.2
Vcc=5V
F=1kHz
THD+N<1%
1.0
0.8
0.2
0.4
RL=4
RL=8 Ω
Ω
RL=16
Ω
0.6
0.8
1.0
Output Power (W)
1.2
1.4
1.6
8/35
TS4994FC Electrical characteristics
Figure 8.
Power dissipation vs. output power Figure 9.
Power dissipation vs. output power
0.6
0.5
Vcc=3.3V
F=1kHz
THD+N<1%
0.4
0.3
RL=4
0.2
0.1
0.0
0.0
RL=8 Ω
0.1
RL=16
Ω
0.2
0.3
0.4
0.5
Output Power (W)
0.6
Ω
0.7
0.40
0.35
Vcc=2.6V
F=1kHz
THD+N<1%
0.30
0.25
0.20
0.15
0.10
0.05
0.00
0.0
RL=16
Ω
0.1
RL=8 Ω
0.2
Output Power (W)
0.3
RL=4
Ω
0.4
Figure 10.
Output power vs. power supply voltage
Figure 11.
Output power vs. power supply voltage
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
2.5
RL = 4 Ω
F = 1kHz
BW < 125kHz
Tamb = 25 ° C
3.0
THD+N=10%
3.5
4.0
Vcc (V)
THD+N=1%
4.5
5.0
5.5
2.0
1.8
1.6
1.4
1.2
RL = 8 Ω
F = 1kHz
BW < 125kHz
Tamb = 25
°
C
1.0
0.8
0.6
0.4
0.2
0.0
2.5
3.0
3.5
THD+N=10%
4.0
Vcc (V)
THD+N=1%
4.5
5.0
5.5
Figure 12.
Output power vs. power supply voltage
Figure 13.
Output power vs. power supply voltage
1.2
1.0
RL = 16
Ω
F = 1kHz
BW < 125kHz
Tamb = 25
°
C
0.8
THD+N=10%
0.6
0.4
0.2
0.0
2.5
3.0
3.5
4.0
Vcc (V)
THD+N=1%
4.5
5.0
5.5
0.6
0.5
RL = 32 Ω
F = 1kHz
BW < 125kHz
Tamb = 25 ° C
0.4
THD+N=10%
0.3
0.2
0.1
0.0
2.5
3.0
3.5
4.0
Vcc (V)
THD+N=1%
4.5
5.0
5.5
9/35
Electrical characteristics
Figure 14.
Power derating curves
1.2
1.0
Heat sink surface
≈
100mm
2
(See demoboard)
0.8
0.6
0.4
0.2
0.0
0
No Heat sink
25 50 75
Ambiant Temperature ( C)
100 125
TS4994FC
Figure 15.
Open loop gain vs. frequency
0
60
40
Gain
20 Phase
0
-20
-40
0.1
Vcc = 5V
ZL = 8 Ω + 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
-40
-80
-120
-160
1000
-200
10000
Figure 16.
Open loop gain vs. frequency
0
60
Gain
40
20 Phase
0
-20
-40
0.1
Vcc = 3.3V
ZL = 8 Ω + 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
-40
-80
-120
-160
1000
-200
10000
Figure 17.
Open loop gain vs. frequency
0
60
Gain
40
20 Phase
0
-20
-40
0.1
Vcc = 2.6V
ZL = 8 Ω + 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
-40
-80
-120
-160
1000
-200
10000
Figure 18.
Closed loop gain vs. frequency
10
0
Gain
Phase
0
-40
-10 -80
-20
Vcc = 5V
-30
Av = 1
-40
0.1
ZL = 8
Ω
+ 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
-120
-160
1000
-200
10000
Figure 19.
Closed loop gain vs. frequency
10
0
Gain
Phase
0
-40
-10
-20
Vcc = 3.3V
-30
-40
0.1
Av = 1
ZL = 8
Ω
+ 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
1000
-200
10000
-80
-120
-160
10/35
TS4994FC
Figure 20.
Closed loop gain vs. frequency
10
0
Gain
-10
Phase
-20
Vcc = 2.6V
-30
Av = 1
-40
0.1
ZL = 8 Ω + 500pF
Tamb = 25
°
C
1 10 100
Frequency (kHz)
-120
-160
1000
-200
10000
0
-40
-80
Electrical characteristics
Figure 21.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 5V
Vripple = 200mVpp
Inputs = Grounded
Av = 1, Cin = 4.7
μ
F
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
1000
Frequency (Hz)
Cb=0.1
μ F
Cb=0
10000 20k
Figure 22.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 3.3V
Vripple = 200mVpp
Inputs = Grounded
Av = 1, Cin = 4.7
μ
F
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
Cb=0.1
1000
Frequency (Hz)
μ
F
Cb=0
10000 20k
Figure 23.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 2.6V
Vripple = 200mVpp
Inputs = Grounded
Av = 1, Cin = 4.7
μ
F
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
1000
Frequency (Hz)
Cb=0.1
μ
F
Cb=0
10000 20k
Figure 24.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 5V
Vripple = 200mVpp
Inputs = Grounded
Av = 2.5, Cin = 4.7
μ
F
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=1
Cb=0.47
μ
F
Cb=0.1
μ
1000
F
Frequency (Hz)
μ
F
Cb=0
10000 20k
Figure 25.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 3.3V
Vripple = 200mVpp
Inputs = Grounded
Av = 2.5, Cin = 4.7
μ
F
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=1
Cb=0.47
μ
F
Cb=0.1
μ
1000
F
Frequency (Hz)
μ
F
Cb=0
10000 20k
11/35
Electrical characteristics
Figure 26.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 2.6V
Vripple = 200mVpp
Inputs = Grounded
Av = 2.5, Cin = 4.7
μ
F
RL
≥
8
Ω
Tamb = 25 ° C
100
Cb=1
Cb=0.47
μ F
Cb=0.1
μ
1000
F
Frequency (Hz)
μ
F
Cb=0
10000 20k
TS4994FC
Figure 27.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 5V
Vripple = 200mVpp
Inputs = Floating
Rfeed = 20k
Ω
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
1000
Frequency (Hz)
Cb=0.1
μ F
Cb=0
10000 20k
Figure 28.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 3.3V
Vripple = 200mVpp
Inputs = Floating
Rfeed = 20k
Ω
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
Cb=0.1
1000
Frequency (Hz)
μ
F
Cb=0
10000 20k
Figure 29.
PSRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 2.6V
Vripple = 200mVpp
Inputs = Floating
Rfeed = 20k
Ω
RL ≥ 8 Ω
Tamb = 25
°
C
100
Cb=0.47
Cb=1
μ
F
μ F
1000
Frequency (Hz)
Cb=0.1
μ
F
Cb=0
10000 20k
Figure 30.
PSRR vs. common mode input voltage
0
-20
-40
Vcc = 5V
Vripple = 200mVpp
Inputs Grounded
F = 217Hz
Av = 1
RL ≥ 8 Ω
Tamb = 25
°
C
-60
Cb=0
-80
Cb=1
μ
F
Cb=0.47
μ
F
Cb=0.1
μ F
-100
0 1 2 3
Common Mode Input Voltage (V)
4 5
Figure 31.
PSRR vs. common mode input voltage
0
-20
-40
Vcc = 3.3V
Vripple = 200mVpp
Inputs Grounded
F = 217Hz
Av = 1
RL
≥
8
Ω
Tamb = 25
°
C
-60
Cb=0
-80
-100
0.0
0.6
1.2
Cb=1
μ
F
Cb=0.47
μ F
Cb=0.1
μ
F
1.8
2.4
Common Mode Input Voltage (V)
3.0
12/35
TS4994FC
Figure 32.
PSRR vs. common mode input voltage
Electrical characteristics
Figure 33.
CMRR vs. frequency
0
-20
-40
Vcc = 2.5V
Vripple = 200mVpp
Inputs Grounded
F = 217Hz
Av = 1
RL
≥
8
Ω
Tamb = 25
°
C
-60
Cb=0
-80
-100
0.0
0.5
1.0
1.5
Cb=1
2.0
Common Mode Input Voltage (V)
μ F
Cb=0.47
Cb=0.1
μ
μ
F
F
2.5
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 5V
Vic = 200mVpp
Av = 1, Cin = 470
μ
F
RL
≥
8
Ω
Tamb = 25 ° C
100
Cb=1 μ F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ
F
1000
Frequency (Hz)
10000 20k
Figure 34.
CMRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 3.3V
Vic = 200mVpp
Av = 1, Cin = 470
μ
F
RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1 μ F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ F
1000
Frequency (Hz)
10000 20k
Figure 35.
CMRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
20
Vcc = 2.6V
Vic = 200mVpp
Av = 1, Cin = 470 μ F
RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1 μ F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ F
1000
Frequency (Hz)
10000 20k
Figure 36.
CMRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
Vcc = 5V
Vic = 200mVpp
Av = 2.5, Cin = 470 μ F
RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1
μ
F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ
F
1000
Frequency (Hz)
10000 20k
Figure 37.
CMRR vs. frequency
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
20
Vcc = 3.3V
Vic = 200mVpp
Av = 2.5, Cin = 470 μ F
RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1
μ
F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ
F
1000
Frequency (Hz)
10000 20k
13/35
Electrical characteristics
Figure 38.
CMRR vs. frequency
-40
-50
-60
-70
-80
-90
0
-10
-20
-30
-100
20
Vcc = 2.6V
Vic = 200mVpp
Av = 2.5, Cin = 470
μ
F
RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1 μ F
Cb=0.47
μ
F
Cb=0.1
Cb=0
μ F
1000
Frequency (Hz)
10000 20k
TS4994FC
Figure 39.
CMRR vs. common mode input voltage
0
-20 Vcc=2.5V
Vcc=3.3V
-40
-60
-80
Vic = 200mVpp
F = 217Hz
Av = 1, Cb = 1 μ F
RL
≥
8
Ω
Tamb = 25
°
C
-100
Vcc=5V
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Common Mode Input Voltage (V)
Figure 40.
CMRR vs. common mode input voltage
Figure 41.
THD+N vs. output power
0
Vcc=3.3V
-20
-40
-60
Vcc=2.5V
Vic = 200mVpp
F = 217Hz
Av = 1, Cb = 0
RL
≥
8
Ω
Tamb = 25 ° C
-80
-100
Vcc=5V
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
Common Mode Input Voltage (V)
10
1
RL = 4 Ω
F = 20Hz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
0.01
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
0.1
Output Power (W)
1
Figure 42.
THD+N vs. output power
10
1
RL = 4
Ω
F = 20Hz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
Figure 43.
THD+N vs. output power
10
1
RL = 4
Ω
F = 20Hz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
1
0.01
1E-3 0.01
0.1
Output Power (W)
1
14/35
TS4994FC
Figure 44.
THD+N vs. output power
10
1
RL = 8 Ω
F = 20Hz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
0.1
Output Power (W)
1
Figure 46.
THD+N vs. output power
10
1
RL = 8 Ω
F = 20Hz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
1
Figure 48.
THD+N vs. output power
10
1
RL = 16 Ω
F = 20Hz
Av = 2.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
Output Power (W)
0.1
1
Electrical characteristics
Figure 45.
THD+N vs. output power
10
1
RL = 8 Ω
F = 20Hz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
0.1
Output Power (W)
1
Figure 47.
THD+N vs. output power
10
1
RL = 16
Ω
F = 20Hz
Av = 1
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
Output Power (W)
0.1
1
Figure 49.
THD+N vs. output power
10
1
RL = 16 Ω
F = 20Hz
Av = 7.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
Output Power (W)
0.1
1
15/35
Electrical characteristics
Figure 50.
THD+N vs. output power
10
1
RL = 4 Ω
F = 1kHz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
1
Figure 52.
THD+N vs. output power
10
1
RL = 4 Ω
F = 1kHz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.1
1E-3
0.01
1E-3
0.01
0.1
Output Power (W)
Figure 54.
THD+N vs. output power
10
1
RL = 8
Ω
F = 1kHz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
0.1
Output Power (W)
1
1
Figure 51.
THD+N vs. output power
10
1
RL = 4
Ω
F = 1kHz
Av = 2.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
TS4994FC
1
Figure 53.
THD+N vs. output power
10
1
RL = 8 Ω
F = 1kHz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
1
Figure 55.
THD+N vs. output power
10
1
RL = 8
Ω
F = 1kHz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
0.1
Output Power (W)
1
16/35
TS4994FC
Figure 56.
THD+N vs. output power
10
1
RL = 16
Ω
F = 1kHz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
Output Power (W)
0.1
1
Electrical characteristics
Figure 57.
THD+N vs. output power
10
1
RL = 16
Ω
F = 1kHz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
Output Power (W)
0.1
1
Figure 58.
THD+N vs. output power
10
1
RL = 16
Ω
F = 1kHz
Av = 7.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3 0.01
Output Power (W)
0.1
Figure 60.
THD+N vs. output power
10
1
RL = 4
Ω
F = 20kHz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
Vcc=2.6V
Vcc=3.3V
Vcc=5V
1
Figure 59.
THD+N vs. output power
10
1
RL = 4 Ω
F = 20kHz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
1E-3
Figure 61.
10
1
RL = 4
Ω
F = 20kHz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25
°
C
0.01
0.1
Output Power (W)
THD+N vs. output power
Vcc=5V
Vcc=2.6V
Vcc=3.3V
1
0.1
1E-3 0.01
0.1
Output Power (W)
1
0.1
1E-3 0.01
0.1
Output Power (W)
1
17/35
Electrical characteristics
Figure 62.
THD+N vs. output power
10
1
RL = 8 Ω
F = 20kHz
Av = 1
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.1
1E-3 0.01
0.1
Output Power (W)
1
Figure 64.
THD+N vs. output power
10
1
RL = 8 Ω
F = 20kHz
Av = 7.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
Vcc=5V
Vcc=2.6V
Vcc=3.3V
Figure 63.
0.1
1E-3
THD+N vs. output power
10
1
RL = 8 Ω
F = 20kHz
Av = 2.5
Cb = 1
μ
F
BW < 125kHz
Tamb = 25 ° C
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.01
0.1
Output Power (W)
TS4994FC
1
Figure 65.
THD+N vs. output power
10
1
RL = 16
Ω
F = 20kHz
Av = 1
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
0.1
1E-3 0.01
0.1
Output Power (W)
Figure 66.
THD+N vs. output power
10
1
RL = 16 Ω
F = 20kHz
Av = 2.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V
Vcc=3.3V
Vcc=5V
1
0.01
1E-3 0.01
Output Power (W)
0.1
1
0.01
1E-3 0.01
Output Power (W)
0.1
Figure 67.
THD+N vs. output power
10
1
RL = 16 Ω
F = 20kHz
Av = 7.5
Cb = 1 μ F
BW < 125kHz
Tamb = 25
°
C
Vcc=2.6V
Vcc=3.3V
Vcc=5V
1
0.1
1E-3 0.01
Output Power (W)
0.1
1
18/35
TS4994FC
Figure 68.
THD+N vs. frequency
10
1
RL = 4 Ω
Av = 1
Cb = 1
μ
F
Bw < 125kHz
Tamb = 25
°
C
0.1
Vcc=2.6V, Po=350mW
0.01
1E-3
20
Vcc=5V, Po=1W
100 1000
Frequency (Hz)
10000 20k
Figure 69.
THD+N vs. frequency
10
1
RL = 4 Ω
Av = 7.5
Cb = 1
μ
F
Bw < 125kHz
Tamb = 25
°
C
0.1
0.01
20
Electrical characteristics
Vcc=5V, Po=1W
Vcc=2.6V, Po=350mW
100 1000
Frequency (Hz)
10000 20k
Figure 70.
THD+N vs. frequency
10
1
RL = 8
Ω
Av = 1
Cb = 1 μ F
Bw < 125kHz
Tamb = 25
°
C
0.1
Vcc=5V, Po=850mW
0.01
1E-3
20 100 1000
Vcc=2.6V, Po=225mW
10000 20k
Frequency (Hz)
Figure 71.
THD+N vs. frequency
10
1
RL = 8
Ω
Av = 7.5
Cb = 1 μ F
Bw < 125kHz
Tamb = 25
°
C
Vcc=2.6V, Po=225mW
Vcc=5V, Po=850mW
0.1
0.01
20 100 1000
Frequency (Hz)
10000 20k
Figure 72.
THD+N vs. frequency
10
1
RL = 16
Ω
Av = 1
Cb = 1 μ F
Bw < 125kHz
Tamb = 25 ° C
0.1
Vcc=2.6V, Po=155mW
0.01
1E-3
20 100 1000
Vcc=5V, Po=600mW
10000 20k
Frequency (Hz)
Figure 73.
THD+N vs. frequency
10
1
RL = 16
Ω
Av = 7.5
Cb = 1 μ F
Bw < 125kHz
Tamb = 25 ° C
0.1
Vcc=5V, Po=600mW
0.01
1E-3
20 100
Vcc=2.6V, Po=155mW
1000
Frequency (Hz)
10000 20k
19/35
Electrical characteristics
Figure 74.
THD+N vs. output power
10
1
RL = 4
Ω
Vcc = 5V
Av = 1
Cb = 0
BW < 125kHz
Tamb = 25
°
C
0.1
F=20Hz
F=20kHz
F=1kHz
0.01
1E-3 0.01
0.1
Output Power (W)
1
Figure 76.
THD+N vs. output power
10
1
RL = 4
Ω
Vcc = 2.6V
Av = 1, Cb = 0
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
F=20kHz
F=1kHz
F=20Hz
0.01
Output Power (W)
0.1
Figure 78.
THD+N vs. output power
10
1
RL = 8
Ω
Vcc = 5V
Av = 1
Cb = 0
BW < 125kHz
Tamb = 25
°
C
0.1
F=20kHz
F=1kHz
F=20Hz
0.01
1E-3 0.01
0.1
Output Power (W)
1
TS4994FC
Figure 75.
THD+N vs. output power
10
1
RL = 4
Ω
Vcc = 5V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25 ° C
F=20kHz
F=1kHz
F=20Hz
0.1
1E-3 0.01
0.1
Output Power (W)
1
Figure 77.
THD+N vs. output power
10
1
RL = 4
Ω
Vcc = 2.6V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25
°
C
F=20kHz
F=20Hz
F=1kHz
0.1
1E-3 0.01
Output Power (W)
0.1
Figure 79.
THD+N vs. output power
10
1
RL = 8
Ω
Vcc = 5V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25
°
C
F=20kHz
F=1kHz
0.1
0.01
1E-3
F=20Hz
0.01
0.1
Output Power (W)
1
20/35
TS4994FC
Figure 80.
THD+N vs. output power
10
1
RL = 8
Ω
Vcc = 2.6V
Av = 1, Cb = 0
BW < 125kHz
Tamb = 25 ° C
0.1
F=20kHz
F=1kHz
0.01
1E-3
1E-3
F=20Hz
0.01
Output Power (W)
0.1
Figure 82.
THD+N vs. output power
10
1
RL = 16 Ω
Vcc = 5V
Av = 1, Cb = 0
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
F=20kHz
F=1kHz
F=20Hz
0.01
0.1
Output Power (W)
1
Figure 84.
THD+N vs. output power
10
1
RL = 16
Ω
Vcc = 2.6V
Av = 1, Cb = 0
BW < 125kHz
Tamb = 25
°
C
0.1
0.01
1E-3
1E-3
F=20kHz
F=1kHz
F=20Hz
0.01
Output Power (W)
0.1
Electrical characteristics
Figure 81.
THD+N vs. output power
10
1
RL = 8
Ω
Vcc = 2.6V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25 ° C
F=20kHz
0.1
F=1kHz
0.01
1E-3
F=20Hz
0.01
Output Power (W)
0.1
Figure 83.
THD+N vs. output power
10
1
RL = 16 Ω
Vcc = 5V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25
°
C
F=20kHz
0.1
F=1kHz
0.01
1E-3
F=20Hz
0.01
0.1
Output Power (W)
1
Figure 85.
THD+N vs. output power
10
1
RL = 16
Ω
Vcc = 2.6V
Av = 7.5, Cb = 0
BW < 125kHz
Tamb = 25
°
C
F=20kHz
0.1
0.01
1E-3
F=1kHz
F=20Hz
0.01
Output Power (W)
0.1
21/35
Electrical characteristics TS4994FC
Figure 86.
SNR vs. power supply voltage with unweighted filter
Figure 87.
SNR vs. power supply voltage with
A-weighted filter
110
105
RL=16
Ω
100
95
RL=8
RL=4
Ω
90
Av = 2.5
Cb = 1
μ
F
85
THD+N < 0.7%
80
2.5
Tamb = 25
°
C
3.0
3.5
4.0
Power Supply Voltage (V)
Ω
4.5
5.0
110
105
RL=16
Ω
100
RL=8
Ω
95
RL=4
Ω
90
Av = 2.5
Cb = 1
μ
F
85
THD+N < 0.7%
80
2.5
Tamb = 25
°
C
3.0
3.5
4.0
Power Supply Voltage (V)
4.5
5.0
Figure 88.
Startup time vs. bypass capacitor
20
Tamb=25 ° C
15
Vcc=5V
Vcc=3.3V
10
5
Vcc=2.6V
0
0.0
0.4
0.8
1.2
1.6
Bypass Capacitor Cb ( F)
2.0
22/35
TS4994FC Application information
4.2
Note:
4.3
The TS4994 is a monolithic full-differential input/output power amplifier. The TS4994 also includes a common mode feedback loop that controls the output bias value to average it at
V
CC
/2 for any DC common mode input voltage. This allows the device to always have a maximum output voltage swing, and by consequence, maximize the output power.
Moreover, as the load is connected differentially, compared to a single-ended topology, the output is four times higher for the same power supply voltage.
●
●
●
The advantages of a full-differential amplifier are:
●
●
●
Very high PSRR (power supply rejection ratio).
High common mode noise rejection.
Virtually zero pop without additional circuitry, giving a faster start-up time compared with conventional single-ended input amplifiers.
Easier interfacing with differential output audio DAC.
No input coupling capacitors required due to common mode feedback loop.
In theory, the filtering of the internal bias by an external bypass capacitor is not necessary. But, to reach maximum performance in all tolerance situations, it is better to keep this option.
The main disadvantage is:
● As the differential function is directly linked to the mismatch between external resistors, paying particular attention to this mismatch is mandatory in order to get the best performance from the amplifier.
Gain in typical application schematic
A typical differential application is shown in Figure 1 on page 3
.
In the flat region of the frequency-response curve (no C in expressed by the relation:
effect), the differential gain is
A
V diff
=
V – V
------------------------------------------------------
Diff input+
– Diff input-
=
R
--------------
R in where R in
= R in1
= R in2
and R feed
= R feed1
= R feed2
.
For the rest of this section, Av diff
will be called A
V
to simplify the expression.
Common mode feedback loop limitations
As explained previously, the common mode feedback loop allows the output DC bias voltage to be averaged at V
CC
/2 for any DC common mode bias input voltage.
However, due to V
ICM
limitation of the input stage (see Table 3 on page 5
), the common mode feedback loop can play its role only within a defined range. This range depends upon
23/35
Application information TS4994FC the values of V
CC
, R in
and R feed
( A
V
). To have a good estimation of the V
ICM
value, use the following formula:
V
ICM
=
V × ×
------------------------------------------------------------------------- (V)
2
R in
× (
+
R
2 in
×
+
V
R feed
)
R feed with
V ic
=
Diff +
------------------------------------------------------ (V)
2
Diff input-
The result of the calculation must be in the range:
≤
ICM
≤ V
CC
– 0.9V
If the result of the V
ICM
calculation is not in this range, an input coupling capacitor must be used.
Example: With V
CC
=2.5V, R in
= R feed
= 20k and V ic
= 2V, we find V
ICM
= 1.63V. This is higher than 2.5V - 0.9V = 1.6V, so input coupling capacitors are required. Alternatively, you can change the V ic
value.
4.4 Low and high frequency response
In the low frequency region, C in
starts to have an effect. C in
forms, with R in
, a high-pass filter with a -3dB cut-off frequency. F
CL
is in Hz.
F
CL
=
1
2 × π × R in
× C in
( Hz )
In the high-frequency region, you can limit the bandwidth by adding a capacitor (C feed
) in parallel with R feed
. It forms a low-pass filter with a -3dB cut-off frequency. F
CH
is in Hz.
F
CH
=
1
2 × π × R feed
× C feed
( Hz )
While these bandwidth limitations are in theory attractive, in practice, because of low performance in terms of capacitor precision (and by consequence in terms of mismatching), they deteriorate the values of PSRR and CMRR.
The influence of mismatching on PSRR and CMRR performance is discussed in more detail in the following sections.
Example: A typical application with input coupling and feedback capacitor with F
CL and F
CH
= 8kHz. We assume that the mismatching between R in1,2
and C feed1,2
= 50Hz
can be neglected. If we sweep the frequency from DC to 20kHz we observe the following with respect to the PSRR value:
● From DC to 200Hz, the C in
impedance decreases from infinite to a finite value and the
C feed
impedance is high enough to be neglected. Due to the tolerance of C in1,2
, we
24/35
TS4994FC Application information
●
● must introduce a mismatch factor (R in1 performance.
x C in
≠
R in2 x C in2
) that will decrease the PSRR
From 200Hz to 5kHz, the C in
impedance is low enough to be neglected when compared with R in,
and the C feed
impedance is high enough to be neglected as well. In this range, we can reach the PSRR performance of the TS4994 itself.
From 5kHz to 20kHz, the C in
impedance is low to be neglected when compared to R in, and the C feed
impedance decreases to a finite value. Due to tolerance of C feed1,2
, we introduce a mismatching factor (R feed1 x C feed1
≠
R feed2 x C feed2
) that will decrease the
PSRR performance.
4.5 Calculating the influence of mismatching on PSRR performance
For calculating PSRR performance, we consider that C in
and C feed
have no influence. We use the same kind of resistor (same tolerance) and Δ R is the tolerance value in %.
The following PSRR equation is valid for frequencies ranging from DC to about 1kHz.
The PSRR equation is ( Δ R in %):
PSRR
≤
20
×
Log
⎣
⎢
⎡ Δ
R
( 10000
×
100
− Δ
R
2
) ⎦
⎥
⎤
( dB )
This equation doesn't include the additional performance provided by bypass capacitor filtering. If a bypass capacitor is added, it acts, together with the internal high output impedance bias, as a low-pass filter, and the result is a quite important PSRR improvement with a relatively small bypass capacitor.
The complete PSRR equation (
Δ
R in %, C b
in microFarad and F in Hz) is:
PSRR
≤ 20 × log
(1000 –
Δ R
2
) ×
R
×
1
100
+ F
2
× C b
2
× 22.2
)
Example: With
Δ
R = 0.1% and C b
= 0, the minimum PSRR is -60dB. With a 100nF bypass capacitor, at 100Hz the new PSRR would be -93dB.
This example is a worst case scenario, where each resistor has extreme tolerance. It illustrates the fact that with only a small bypass capacitor, the TS4994 provides high PSRR performance.
Note also that this is a theoretical formula. Because the TS4994 has self-generated noise, you should consider that the highest practical PSRR reachable is about -110dB. It is therefore unreasonable to target a -120dB PSRR.
25/35
Application information TS4994FC
The three following graphs show PSRR versus frequency and versus bypass capacitor C b
in worst-case conditions (
Δ
R = 0.1%).
Figure 89.
PSRR vs. frequency (worst case conditions)
Figure 90.
PSRR vs. frequency (worst case conditions)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Vcc = 5V, Vripple = 200mVpp
Av = 1, Cin = 4.7
μ
F
Δ
R/R = 0.1%, RL
≥
8
Ω
Tamb = 25 ° C, Inputs = Grounded
Cb=1
100
μ
F
Cb=0.1
μ F
Cb=0.47
μ
F
1000
Frequency (Hz)
Cb=0
10000 20k
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Vcc = 3.3V, Vripple = 200mVpp
Av = 1, Cin = 4.7
μ
F
Δ R/R = 0.1%, RL ≥ 8 Ω
Tamb = 25
°
C, Inputs = Grounded
Cb=1
100
μ
F
Cb=0.1
μ F
Cb=0.47
μ
F
1000
Frequency (Hz)
Cb=0
10000 20k
Figure 91.
PSRR vs. frequency (worst case conditions)
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Vcc = 2.5V, Vripple = 200mVpp
Av = 1, Cin = 4.7
μ F
Δ
R/R = 0.1%, RL
≥
8
Ω
Tamb = 25 ° C, Inputs = Grounded
Cb=1
100
μ
F
Cb=0.1
μ F
Cb=0.47
μ
F
1000
Frequency (Hz)
Cb=0
10000 20k
26/35
TS4994FC Application information
The two following graphs show typical applications of the TS4994 with a random selection of four
Δ
R/R values with a 0.1% tolerance.
Figure 92.
PSRR vs. frequency with random choice condition
Figure 93.
PSRR vs. frequency with random choice condition
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Vcc = 5V, Vripple = 200mVpp
Av = 1, Cin = 4.7
μ
F
Δ R/R ≤ 0.1%, RL ≥ 8 Ω
Tamb = 25
°
C, Inputs = Grounded
Cb=1
100
μ
F
Cb=0.1
μ
F
Cb=0.47
μ
F
1000
Frequency (Hz)
Cb=0
10000 20k
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
-140
20
Vcc = 2.5V, Vripple = 200mVpp
Av = 1, Cin = 4.7
μ
F
Δ R/R ≤ 0.1%, RL ≥ 8 Ω
Tamb = 25
°
C, Inputs = Grounded
Cb=1
100
μ
F
Cb=0.1
μ
F
Cb=0.47
μ
F
1000
Frequency (Hz)
Cb=0
10000 20k
For calculating CMRR performance, we consider that C in
and C feed
have no influence. C b has no influence in the calculation of the CMRR.
We use the same kind of resistor (same tolerance) and
Δ
R is the tolerance value in %.
The following CMRR equation is valid for frequencies ranging from DC to about 1kHz.
The CMRR equation is (
Δ
R in %):
CMRR ≤ 20 × Log
⎣
⎢
⎡ Δ
R
( 10000
×
−
200
Δ
R
2
) ⎦
⎥
⎤
Example: With
Δ
R = 1%, the minimum CMRR is -34dB.
( dB )
This example is a worst case scenario where each resistor has extreme tolerance. Ut illustrates the fact that for CMRR, good matching is essential.
As with the PSRR, due to self-generated noise, the TS4994 CMRR limitation is about
-110dB.
and
Figure 95 show CMRR versus frequency and versus bypass capacitor C
b worst-case conditions (
Δ
R=0.1%).
in
27/35
Application information TS4994FC
Figure 94.
CMRR vs. frequency (worst case conditions)
Figure 95.
CMRR vs. frequency (worst case conditions)
0
-10
-20
Vcc = 5V
Vic = 200mVpp
Av = 1, Cin = 470
μ
F
Δ
R/R = 0.1%, RL
≥
8
Ω
Tamb = 25 ° C
-30
-40
Cb=1
μ
F
Cb=0
-50
-60
20 100 1000
Frequency (Hz)
10000 20k
0
-10
-20
Vcc = 2.5V
Vic = 200mVpp
Av = 1, Cin = 470
μ
F
Δ
R/R = 0.1%, RL
≥
8
Ω
Tamb = 25
°
C
-30
-40
Cb=1
μ
F
Cb=0
-50
-60
20 100 1000
Frequency (Hz)
10000 20k
and
Figure 97 show CMRR versus frequency for a typical application with a
random selection of four
Δ
R/R values with a 0.1% tolerance.
Figure 96.
CMRR vs. frequency with random selection condition
Figure 97.
CMRR vs. frequency with random selection condition
0
-10
-20
-30
-40
-50
Vcc = 5V
Vic = 200mVpp
Av = 1, Cin = 470 μ F
Δ
R/R
≤
0.1%, RL
≥
8
Ω
Tamb = 25
°
C
-60
-70
-80
-90
20 100
Cb=1
Cb=0
μ
F
1000
Frequency (Hz)
10000 20k
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
20
Vcc = 2.5V
Vic = 200mVpp
Av = 1, Cin = 470
μ
F
Δ
R/R
≤
0.1%, RL
≥
8
Ω
Tamb = 25
°
C
100
Cb=1
Cb=0
μ
F
1000
Frequency (Hz)
10000 20k
4.7
28/35
Power dissipation and efficiency
Assumptions:
●
●
Load voltage and current are sinusoidal (V
Supply voltage is a pure DC source (V
CC
) out
and I out
)
The output voltage is:
V out
= Vpeak sin ω t (V) and
I out
=
V out
------------ (A)
R
L
TS4994FC
Note:
Application information and
P out
=
V peak
L
2
-------------------- (W)
2R
Therefore, the average current delivered by the supply voltage is:
Equation 1
I
CC AVG = 2
V peak
π R
L
---------------- (A)
The power delivered by the supply voltage is:
P supply
= V
CC
⋅ I
CC
AVG
(W)
Therefore, the power dissipated by each amplifier is:
P diss
= P supply
– P out
(W)
Equation 2
P diss
=
2 2V
---------------------P
π R
L out
– P out and the maximum value is obtained when:
∂
P diss
∂
P out
----------------- = 0 and its value is:
Equation 3
Pdiss max
=
2 Vcc
2
π 2
R
L
( W )
This maximum value is only dependent on the power supply voltage and load values.
The efficiency is the ratio between the output power and the power supply:
Equation 4
η
=
P
------------------ =
P supply
π V
--------------------
4V
CC
The maximum theoretical value is reached when V peak
= V
CC
, so:
η =
π
= 78.5%
4
The maximum die temperature allowable for the TS4994 is 125°C. However, in case of overheating, a thermal shutdown set to 150°C, puts the TS4994 in standby until the temperature of the die is reduced by about 5°C.
29/35
Application information TS4994FC
To calculate the maximum ambient temperature T amb
allowable, you need to know:
● The value of the power supply voltage, V
CC
●
●
The value of the load resistor, R
L
The R thja value for the package type
Example: V
CC
= 5V, R
L
= 8 Ω, R thja-flipchip
= 100°C/W (100mm² copper heatsink)
Using the power dissipation formula given above in Equation 3 this gives a result of:
P dissmax
= 633mW
T amb
is calculated as follows:
Equation 5
T amb
= 125 ° C – R
TJHA
× P dissmax
Therefore, the maximum allowable value for T amb
is:
T amb
= 125-80x0.633=62°C
4.8 Decoupling of the circuit
Two capacitors are needed to correctly bypass the TS4994. A power supply bypass capacitor C s
and a bias voltage bypass capacitor C b
.
C s
has particular influence on the THD+N in the high frequency region (above 7kHz) and an indirect influence on power supply disturbances. With a value for C s of 1µF, you can expect similar THD+N performance to that shown in the datasheet.
In the high frequency region, if C s
is lower than 1µF, it increases THD+N, and disturbances on the power supply rail are less filtered.
On the other hand, if C s
is higher than 1µF, the disturbances on the power supply rail are more filtered.
C b
has an influence on THD+N at lower frequencies, but its function is critical to the final result of PSRR (with input grounded and in the lower frequency region).
4.9 Wake-up time: t
WU
When the standby is released to put the device ON, the bypass capacitor C b
is not charged immediately. As C b
is directly linked to the bias of the amplifier, the bias will not work properly until the C b
voltage is correct. The time to reach this voltage is called the wake-up time or t
WU
and is specified in
, with C b
=1µF. During the wake-up time, the
TS4994 gain is close to zero. After the wake-up time, the gain is released and set to its nominal value.
If C b
has a value other than 1µF, refer to the graph in Figure 88 on page 22 to establish the
wake-up time.
30/35
TS4994FC Application information
Note:
When the standby command is set, the time required to put the two output stages in high impedance and the internal circuitry in shutdown mode is a few microseconds.
In shutdown mode, the Bypass pin and Vin+, Vin- pins are short-circuited to ground by internal switches. This allows a quick discharge of the C b
and C in
capacitors.
Due to its fully differential structure, the pop performance of the TS4994 is close to perfect.
However, due to mismatching between internal resistors R in
, R feed
, and external input capacitors C in
, some noise might remain at startup. To eliminate the effect of mismatched components, the TS4994 includes pop reduction circuitry. With this circuitry, the TS4994 is close to zero pop for all possible common applications.
In addition, when the TS4994 is in standby mode, due to the high impedance output stage in this configuration, no pop is heard.
4.12 Single-ended input configuration
It is possible to use the TS4994 in a single-ended input configuration. However, input
coupling capacitors are needed in this configuration. The schematic in Figure 98
shows an example of this configuration.
Figure 98.
Single-ended input typical application
VCC
+
Cs
1u
Rfeed1
20k
3 Vin-
2
VCC
-
GND
Ve
GND
Cin1
Rin1
220nF
Cin2
20k
Rin2
220nF
20k
+
Cb
1u
GND
1 Vin+
8 Bypass
Mode
9
Stdby
4
+
Bias
Standby
GND
6
GND
Rfeed2
20k
Vo+ 5
Vo-
7
TS4994IJ
8 Ohms
GND VCC GND VCC
The component calculations remain the same, except for the gain. In single-ended input configuration, the formula is:
Av
SE
=
V
O +
−
Ve
V
O −
=
R feed
R in
31/35
Package information TS4994FC
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK
®
packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com
.
Flip-chip package (9 bumps)
Dimensions in millimeters unless otherwise indicated.
Figure 99.
Pinout (top view)
* Balls are underneath
Figure 100. Marking (top view)
32/35
TS4994FC
Figure 101. Dimensions
Package information
●
●
●
●
●
●
●
●
●
Die size: 1.63mm x 1.63mm ± 30µm
Die height (including bumps): 600µm
Bumps diameter: 315µm ±50µm
Bump diameter before reflow: 300µm
±10µm
Bump height: 250µm ±40µm
Back coating height: 40µm ±10µm
Die height: 350µm ±20µm
Pitch: 500µm ±50µm
Coplanarity: 60µm max
Figure 102. Tape & reel dimensions
33/35
Revision history
Table 6.
Date
17-Mar-2005
12-Dec-2006
Document revision history
Revision
1
2
Initial release.
Template update.
Changes
TS4994FC
34/35
TS4994FC
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
35/35
Λήψη
Δημόσιος σύνδεσμος ενημερώθηκε
Ο δημόσιος σύνδεσμος για τη συνομιλία σας ενημερώθηκε. You may view and manage your chat links after registration here.
Δημόσιος σύνδεσμος εγγράφου
Διαφήμιση