STMicroelectronics VNV35NV04 Datasheet

Features

Type R

DS(on)

VNB35NV04

VNV35NV04

10 m

1.

For PowerSO-10 only

Ω (1)

I lim

30 A

V clamp

40 V

■

■

■

■

■

■

■

■

■

Linear current limitation

Thermal shut down

Short circuit protection

Integrated clamp

Low current drawn from input pin

Diagnostic feedback through input pin

ESD protection

Direct access to the gate of the Power

MOSFET (analog driving)

Compatible with standard Power MOSFET

VNB35NV04

VNV35NV04

OMNIFET II

fully autoprotected Power MOSFET

Datasheet

−

production data

1

D

2

PAK

3

10

1

PowerSO-10

Description

The VNB35NV04 and VNV35NV04 are monolithic devices designed in STMicroelectronics

®

VIPower

®

M0-3 Technology, intended for replacement of standard Power MOSFETs from

DC up to 25 kHz applications.

Built in thermal shutdown, linear current limitation and overvoltage clamp protect the chip in harsh environments. Fault feedback can be detected by monitoring the voltage at the input pin.

Obsolete Product(s) - Obsolete Product(s)

Table 1.

Device summary

Order codes

Package

Tube Tape and reel

D

2

PAK VNB35NV04 VNB35NV0413TR

PowerSO-10 VNV35NV04 VNV35NV0413TR

September 2013

This is information on a product in full production.

Doc ID 023692 Rev. 2 1/24 www.st.com

1

1

2

Contents

Contents

3

4

VNB35NV04, VNV35NV04

Block diagram and pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1

Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2

Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3

Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.4

Protection features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5

Electrical characteristics curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Package informantion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.1

ECOPACK

®

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2

PowerSO-10 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3

D2PAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.4

PowerSO-10 packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.5

D

2

PAK packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Obsolete Product(s) - Obsolete Product(s)

2/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04

List of tables

List of tables

Table 1.

Table 2.

Table 3.

Table 4.

Table 5.

Table 6.

Table 7.

Table 8.

Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Thermal data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Switching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Source drain diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Protections (-40°C < Tj < 150°C, unless otherwise specified) . . . . . . . . . . . . . . . . . . . . . . . 8

Table 9.

PowerSO-10 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Table 10.

D2PAK mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 11.

Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 3/24

VNB35NV04, VNV35NV04 List of figures

List of figures

Figure 1.

Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 2.

Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Figure 3.

Current and voltage conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 4.

Switching time test circuit for resistive load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 5.

Test circuit for diode recovery times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Figure 6.

Unclamped inductive load test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 7.

Unclamped inductive waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 8.

Input charge test circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 9.

Source-drain diode forward characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 10.

Static drain source on resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 11.

PowerSO-10 static drain-source on resistance vs. input voltage . . . . . . . . . . . . . . . . . . . . 13

Figure 12.

D

2

PAK static drain-source on resistance vs. input voltage. . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 13.

PowerSO-10 static drain-source on resistance vs. id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 14.

D

2

PAK static drain-source on resistance vs. id . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 15.

Transconductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 16.

Transfer characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 17.

Output characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 18.

Normalized on resistance vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 19.

Turn-on current slope, V

IN

Figure 20.

Turn-on current slope, V

IN

= 5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

= 3.5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 21.

Input voltage vs. input charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 22.

Turn-off drain source voltage slope, V

IN

Figure 23.

Turn-off drain-source voltage slope, V

IN

= 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

= 3.5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 24.

Switching time resistive load (part 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 25.

Switching time resistive load (part 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 26.

Normalized input threshold voltage vs. temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Figure 27.

Current limit vs. junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 28.

Step response current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 29.

Derating curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 30.

PowerSO-10 package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 31.

D2PAK package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 32.

PowerSO-10 suggested pad layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 33.

Tube shipment (no suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 34.

Tape and reel shipment (suffix “13TR”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 35.

D

2

PAK footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 36.

Tube shipment (no suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Figure 37.

Tape and reel shipment (suffix “13TR”) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Obsolete Product(s) - Obsolete Product(s)

4/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04

1

Block diagram and pin connection

Block diagram and pin connection

Figure 1.

Block diagram

DRAIN

2

Overvoltage

Clamp

INPUT

1

Gate

Control

Over

Temperature

Linear

Current

Limiter

3

SOURCE

Figure 2.

Pin connection

INPUT

INPUT

INPUT

INPUT

INPUT

DRAIN

8

9

6

7

10

11

1.

For the pins configuration related to D

2

PAK, see Figure 1

.

2

1

5

4

3

SOURCE

SOURCE

N.C.

SOURCE

SOURCE

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 5/24

Electrical specification VNB35NV04, VNV35NV04

Figure 3.

Current and voltage conventions

I

IN

R

IN

INPUT

DRAIN

SOURCE

I

D

V

IN

V

DS

Stressing the device above the rating listed in

Table 2

may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the operating sections of this specification is not implied.

Exposure to the conditions in table below for extended periods may affect device reliability

Table 2.

Absolute maximum ratings

Value

Symbol Parameter Unit

PowerSO-10 D

2

PAK

V

DS

V

IN

I

IN

R

IN MIN

I

D

Drain-source voltage (V

IN

= 0 V)

Input voltage

Input current

Minimum input series impedance

Drain current

Internally clamped

Internally clamped

+/-20

4.7

Internally limited

Reverse DC output current -30 I

R

V

ESD1

V

ESD2

Electrostatic discharge (R = 1.5 K Ω , C = 100 pF) 4000

Obsolete Product(s) - Obsolete Product(s)

(R = 330 Ω , C = 150 pF)

V

V

A

125 125 W P tot

T j

T c

T stg

Total dissipation at T c

= 25°C

Operating junction temperature

Case operating temperature

Internally limited

Internally limited

°C

Storage temperature -55 to 150

°C

°C

V

V mA

Ω

A

6/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Electrical specification

Table 3.

Thermal data

Value

Symbol Parameter Unit

PowerSO-10 D

2

PAK

R thj-case

Thermal resistance junction-case (max) 1 1 °C/W

R thj-amb

Thermal resistance junction-ambient (max) 50

(1)

50

(1)

°C/W

1.

When mounted on a standard single-sided FR4 board with 50mm

2 to all DRAIN pins.

of Cu (at least 35 mm thick) connected

-40°C < T j

< 150°C, unless otherwise specified.

Table 4.

Symbol

Off

Parameter Test conditions Min Typ Max Unit

V

CLAMP

V

CLTH

Drain-source clamp voltage

Drain-source clamp threshold voltage

V

INTH

V

I

I

ISS

INCL

DSS

V

V

IN

IN

= 0 V; I

= 0 V; I

D

D

= 15 A 40

= 2 mA 36

45 55

Input threshold voltage V

DS

= V

IN

; I

D

= 1 mA 0.5

2.5

Supply current from input pin

V

DS

= 0 V; V

IN

= 5 V 100 150

Input-source clamp voltage

Zero input voltage drain current (V

IN

= 0 V)

I

IN

= 1 mA

I

IN

= -1 mA

V

DS

T j

= 13 V; V

= 25 °C

IN

= 0 V;

6

-1.0

6.8

8

-0.3

30

V

DS

= 25 V; V

IN

= 0 V 75

μ

μ

μ

V

V

V

A

V

V

A

A

T j

= 25°C, unless otherwise specified

Table 5.

Symbol

Dynamic

Parameter Test conditions Min Typ Max Unit

Forward transconductance

V

DD

= 13 V; I

D

= 15 A — 35

C

OSS

Output capacitance V

DS

= 13 V; f = 1 MHz; V

1.

Pulsed: Pulse duration = 300 ms, duty cycle 1.5%

IN

= 0 V — 1300

—

—

S pF

Doc ID 023692 Rev. 2 7/24

Electrical specification VNB35NV04, VNV35NV04

Table 6.

Symbol t d(on) t r t d(off) t f t d(on) t r t d(off) t f

Switching

Parameter

Turn-on delay time

Rise time

Turn-off delay time

Fall time

Turn-on delay time

Rise time

Turn-off delay time

Fall time

(di/dt) on

Turn-on current slope

Q i

Total input charge

V

DD

V gen

R gen

V

V

DD gen

Figure 3

)

Test conditions

= 15 V; I

D

= 5 V;

= R

Figure 3

)

IN MIN

= 15 V; I

= 5 V; R

D

= 15 A;

= 4.7

gen

Ω

= 15 A;

(see

= 2.2 K Ω (see

V

DD

R gen

= 15 V; I

D

= R

IN MIN

= 15 A;V gen

= 4.7

Ω

= 5 V;

I

V

DD gen

= 12 V; I

D

= 15 A; V

IN

= 5 V;

= 2.13 mA (see

Figure 8 )

Min Typ Max Unit

—

—

—

—

—

—

—

—

—

150

840

980

600 1500 ns

4

27

34

31

18

500

2500

3000

12

100

120

110 ns ns ns

μ s

μ s

μ s

μ s

A/ μ s

— 118 nC

Table 7.

Source drain diode

Symbol

V

SD

(1) t rr

I

Q rr

RRM

Parameter Test Conditions

Forward on voltage

Reverse recovery time

I

SD

= 15 A; V

IN

= 0 V

Reverse recovery charge

Reverse recovery current

I

SD

V

DD

= 15 A; dI/dt = 100 A/ μ s;

= 30 V; L = 200 μ H (see

Figure 4

)

1.

Pulsed: Pulse duration = 300 ms, duty cycle 1.5%

Min Typ Max Unit

—

—

0.8

400

—

—

V ns

— 1.4

— μ C

— 7 — A

Table 8.

Symbol

Protections (-40°C < T j

< 150°C, unless otherwise specified)

Parameter Test Conditions Min Typ Max Unit

I lim t dlim

45

50

60 Drain current limit V

IN

= 6 V; V

DS

= 13 V 30

Step response current limit

V

IN

= 6 V; V

DS

= 13 V

T jsh

T

Overtemperature shutdown

150 175

135

200 Obsolete Product(s) - Obsolete Product(s) °C

°C jrs reset

I gf

Fault Sink Current 10 15 20 mA V

IN

= 5 V; V

DS

= 13 V; T j

= T jsh

E as

Single pulse avalanche energy

Starting T j

V

IN

= 5 V;

= 25°C; V

DD

= 24 V;

R gen

= R

IN MIN

= 4.7

Ω;

L = 24 mH (see Figure 6 and

Figure 7

)

1.7

J

A

μ s

8/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Electrical specification

During normal operation, the INPUT pin is electrically connected to the gate of the internal power MOSFET through a low impedance path.

The device then behaves like a standard power MOSFET and can be used as a switch from

DC up to 25 KHz. The only difference from the user’s standpoint is that a small DC current

I

ISS

(typ. 100 µA) flows into the INPUT pin in order to supply the internal circuitry.

The device integrates:

● Overvoltage clamp protection:

●

● internally set at 45 V, along with the rugged avalanche characteristics of the Power

MOSFET stage give this device unrivalled ruggedness and energy handling capability.

This feature is mainly important when driving inductive loads.

Linear current limiter circuit: limits the drain current I

D

to I lim

whatever the INPUT pin voltages is. When the current limiter is active, the device operates in the linear region, so power dissipation may exceed the capability of the heatsink. Both case and junction temperatures increase, and if this phase lasts long enough, junction temperature may reach the overtemperature threshold T jsh

.

Overtemperature and short circuit protection:

● these are based on sensing the chip temperature and are not dependent on the input voltage. The location of the sensing element on the chip in the power stage area ensures fast, accurate detection of the junction temperature. Overtemperature cutout occurs in the range 150°C to 190°C, a typical value being 170°C. The device is automatically restarted when the chip temperature falls of about 15°C below shutdown temperature.

Status feedback: in the case of an overtemperature fault condition (T j

> T jsh

), the device tries to sink a diagnostic current I gf

through the INPUT pin in order to indicate fault condition. If driven from a low impedance source, this current may be used in order to warn the control circuit of a device shutdown. If the drive impedance is high enough so that the INPUT pin driver is not able to supply the current I gf

, the INPUT pin falls to 0 V. This does not however affect the device operation: no requirement is put on the current capability of the INPUT pin driver except to be able to supply the normal operation drive current I

ISS

.

Additional features of this device are ESD protection according to the Human Body model and the ability to be driven from a TTL Logic circuit.

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 9/24

Electrical specification

Figure 4.

Switching time test circuit for resistive load

VNB35NV04, VNV35NV04

9

JHQ

9

'

5

JHQ

,

'

9

JHQ

W

GRQ

W

U

W

GRII

W

I

W

Figure 5.

Test circuit for diode recovery times

$

:

'

,

201,)(7

6

%

)$67

',2'(

$

%

5

JHQ

,

201,)(7

'

/ X+

9

''

9

JHQ

6

W

("1($'5

("1($'5

10/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04

Figure 6.

Unclamped inductive load test circuits

Electrical specification

9

,1

3

:

5

*(1

Figure 7.

Unclamped inductive waveforms

("1($'5

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 11/24

Electrical specification

Figure 8.

Input charge test circuit

V

IN

GEN

VNB35NV04, VNV35NV04

ND8003

Obsolete Product(s) - Obsolete Product(s)

12/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Electrical specification

Figure 9.

Source-drain diode forward characteristics

Vsd (mV)

950

Figure 10.

Static drain source on resistance

900

850

Vin=0V

Rds(on) (mOhm)

50

Vin=2.5V

40

Tj=-40ºC

800

Tj=25ºC

Tj=150ºC

30

750

20

700

650

0 5 10 15

Id (A)

20 25 30 35

Figure 11.

PowerSO-10 static drainsource on resistance vs. input voltage

Rds(on) (mOhm)

27.5

25

Id=15A

Id=7.5A

22.5

20

17.5

15

12.5

10

7.5

5

2

Id=15A

Id=7.5A

Id=15A

Id=7.5A

2.5

3 3.5

Tj=25°C

Tj=150°C

4 4.5

Vin (V)

Tj=-40°C

5 5.5

6 6.5

Figure 13.

PowerSO-10 static drainsource on resistance vs. id

Rds(on) (mOhm)

30

25

15

10

5

0

0

Vin=5V

Tj=150ºC

Tj=25ºC

Tj=-40ºC

5 10 15

Id (A)

20 25 30 35

10

0 1 2 3

Id (A)

4 5 6

Figure 12.

D

2

PAK static drain-source on resistance vs. input voltage

Rds(on) (mOhm)

30

25

20

15

10

5

0

2.5

3 3.5

Tj=150ºC

Tj=25ºC

Tj=-40ºC

4 4.5

Vin (V)

5 5.5

Id=15A

Id=7.5A

Id=15A

Id=7.5A

Id=15A

Id=7.5A

6

12

9

6

3

0

0

Rds(on) (mOhm)

24

21

18

15

4

Vin=5V

8

Tj=150ºC

Tj=25ºC

Tj=-40ºC

12 16

Id (A)

20 24 28 32

6.5

Figure 14.

D

2

PAK static drain-source on resistance vs. id

Doc ID 023692 Rev. 2 13/24

Electrical specification VNB35NV04, VNV35NV04

Figure 15.

Transconductance

Gfs (S)

54

48

42

36

30

24

18

12

6

0

0 4

Vds=13V

8 12 16

Id (A)

20 24

Tj=-40ºC

Tj=25ºC

Tj=150ºC

28 32

Figure 17.

Output characteristics

Figure 16.

Transfer characteristics

Idon (A)

50

45

40

35

30

25

20

Vds=13.5V

15

Tj=150ºC

10

5

0

1 1.5

2 2.5

Tj=25ºC

3 3.5

4

Vin (V)

4.5

5

Tj=-40ºC

5.5

6 6.5

Figure 18.

Normalized on resistance vs. temperature

25

20

15

10

5

0

0

45

40

35

30

Id (A)

55

50

Vin=4.5V

Vin=4V

Vin=3.5V

0.25

0.5

0.75

Vin=3V

1 1.25

Vds (V)

1.5

1.75

Vin=2.5V

2 2.25

2.5

Rds(on) (mOhm)

4

3.5

3

2.5

Vin=5V

Id=15A

2

1.5

1

0.5

0

-50 -25 0 25 50 75

Tc (ºC)

100 125 150 175

Figure 19.

Turn-on current slope,

V

IN

= 5 V

Figure 20.

Turn-on current slope,

V

IN

= 3.5 V di/dt (A/us)

20

17.5

15

12.5

Vin=5V

Vdd=15V

Id=15A di/dt (A/us)

10

9

8

7

6

Vin=3.5V

Vdd=15V

Id=15A

5

10

4

7.5

Obsolete Product(s) - Obsolete Product(s)

5

3

2

2.5

1

0

0

0

0 150 300 450 600

Rg (Ohm)

750 900 1050

125 250 375 500 625

Rg (Ohm)

750 875 1000 1125

14/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Electrical specification

Figure 21.

Input voltage vs. input charge Figure 22.

Turn-off drain source voltage slope, V

IN

= 5 V

Vin (V)

8

7

6

5

4

3

2

1

0

0 25

Vds=12V

Id=15A

50 75 100

Qg (nC)

125 150 175 dV/dt (V/us)

160

140

120

100

80

60

40

20

0

0 150

Vin=5V

Vdd=15V

Id=15A

300 450 600

Rg (Ohm)

750 900 1050

Figure 23.

Turn-off drain-source voltage slope, V

IN

= 3.5 V

Figure 24.

Switching time resistive load

(part 1) dV/dt (V/us)

160

140

120

100

80

60

40

20

0

0 150

Vin=3.5V

Vdd=15V

Id=15A

300 450 600

Rg (Ohm)

750 900 1050

T (us)

40

35

30

25

20

15

10

5

0

0

Vdd=15V

Id=15A

Rg=4.7ohm

td(off) tf tr td(on)

300 600 900 1200

Rg (Ohm)

1500 1800 2100 2400

Figure 25.

Switching time resistive load

(part 2)

Figure 26.

Normalized input threshold voltage vs. temperature

T (ns)

1750

Vinth (V)

2 tr

1.75

1500

Vdd=15V

Id=15A

Rg=4.7ohm

Vds=Vin

Id=1mA td(off) 1.5

1250

1000

1.25

Obsolete Product(s) - Obsolete Product(s)

750

1 tf 0.75

500

0.5

250 td(on)

0.25

0

3 3.5

4 4.5

5

Vin (V)

5.5

6 6.5

7

0

-50 -25 0 25 50 75

Tc (ºC)

100 125 150 175

Doc ID 023692 Rev. 2 15/24

Electrical specification

Figure 27.

Current limit vs. junction temperature

Ilim (A)

100

90

80

70

60

50

40

30

20

10

0

-50 -25

Vin=6V

Vds=13V

0 25 50 75

Tc (ºC)

100 125 150 175

Figure 29.

Derating curve

VNB35NV04, VNV35NV04

Figure 28.

Step response current limit

Tdlim (us)

180

160

140

120

100

80

60

40

0 5

Vin=6V

10 15

Vdd (V)

20 25 30 35

Obsolete Product(s) - Obsolete Product(s)

16/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Package informantion

3.1 ECOPACK

®

In order to meet environmental requirements, ST offers these devices in different grades of

ECOPACK

®

packages, depending on their level of environmental compliance. ECOPACK

® specifications, grade definitions and product status are available at: www.st.com

.

ECOPACK

®

is an ST trademark.

Table 9.

PowerSO-10 mechanical data mm.

Dim.

Min.

Typ.

Max.

A

A1

A2

A3 b c

D

D1

(1)

E

E1

(1)

E2

E3 e

7.40

13.80

9.30

7.20

5.90

0.00

3.40

1.25

0.40

0.35

9.40

1.27

L

<

0.95

0°

1.65

8°

1.

Resin protrusion not included (max value: 0.20 mm per side)

Obsolete Product(s) - Obsolete Product(s)

3.70

0.10

3.60

1.35

0.53

0.55

9.60

7.60

14.40

9.50

7.60

6.10

Doc ID 023692 Rev. 2 17/24

Package informantion

Figure 30.

PowerSO-10 package dimensions

VNB35NV04, VNV35NV04

'!0'#&4

Obsolete Product(s) - Obsolete Product(s)

18/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04

3.3 D

2

PAK mechanical data

Table 10.

D

2

PAK mechanical data

Dim.

e e1

H

J1

L

L1

L2

R

V2 c c2

D

D1

E

E1

A

A1 b b2

4.88

15

2.49

2.29

1.27

1.30

Min.

0.45

1.23

8.95

7.50

10

8.50

4.40

0.03

0.70

1.14

0° mm.

Typ

2.54

0.4

Package informantion

Max.

4.60

0.23

0.93

1.70

0.60

1.36

9.35

10.40

5.28

15.85

2.69

2.79

1.40

1.75

8°

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 19/24

Package informantion

Figure 31.

D

2

PAK package dimensions

VNB35NV04, VNV35NV04

("1($'5

Obsolete Product(s) - Obsolete Product(s)

20/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Package informantion

Figure 32.

PowerSO-10 suggested pad layout

Figure 33.

Tube shipment (no suffix)

&$6$%/$1&$

"

&

08$5

$ &

$

%

$OOGLPHQVLRQVDUHLQPP

&DVDEODQFD

0XDU

%DVH4W\ %XON4W\ 7XEHOHQJWK “ $ % &“

*$3*&)7

("1($'5

Figure 34.

Tape and reel shipment (suffix “13TR”)

5((/',0(16,216

%DVH4W\

%XON4W\

$PD[

%PLQ

&“

)

*

1PLQ

7PD[

$OOGLPHQVLRQVDUHLQPP

7$3(',0(16,216

$FFRUGLQJWR(OHFWURQLF,QGXVWULHV$VVRFLDWLRQ

(,$6WDQGDUGUHY$)HE

7DSHZLGWK

7DSH+ROH6SDFLQJ

&RPSRQHQW6SDFLQJ

+ROH'LDPHWHU

+ROH'LDPHWHU

+ROH3RVLWLRQ

&RPSDUWPHQW'HSWK

+ROH6SDFLQJ

:

3“

3

'“

'PLQ

)“

.PD[

3“

(QG

7RS

FRYHU

WDSH

1RFRPSRQHQWV

PPPLQ

&RPSRQHQWV 1RFRPSRQHQWV

(PSW\FRPSRQHQWVSRFNHWV

VDOHGZLWKFRYHUWDSH

PPPLQ

8VHUGLUHFWLRQRIIHHG

6WDUW

("1($'5

Doc ID 023692 Rev. 2 21/24

Package informantion VNB35NV04, VNV35NV04

3.5 D

2

PAK packing information

Figure 35.

D

2

PAK footprint Figure 36.

Tube shipment (no suffix)

A

16.90

12.20

9.75

1.60

5.08

3.50

All dimensions are in millimeters

B

C

Base Q.ty

Bulk Q.ty

Tube length (± 0.5)

A

B

C (± 0.1)

All dimensions are in mm.

50

500

532

6

21.3

0.6

Figure 37.

Tape and reel shipment (suffix “13TR”)

REEL DIMENSIONS

Base Q.ty

Bulk Q.ty

A (max)

B (min)

C (± 0.2)

F

G (+ 2 / -0)

N (min)

T (max)

1000

1000

330

1.5

13

20.2

24.4

60

30.4

All dimensions are in mm.

TAPE DIMENSIONS

According to Electronic Industries Association

(EIA) Standard 481 rev. A, Feb 1986

Tape width

Tape Hole Spacing

Component Spacing

Hole Diameter

Hole Diameter

Hole Position

Compartment Depth

Hole Spacing

W

P0 (± 0.1)

P

D1 (min)

K (max)

P1 (± 0.1)

24

4

16

D (± 0.1/-0) 1.5

1.5

F (± 0.05) 11.5

6.5

2

All dimensions are in mm.

Obsolete Product(s) - Obsolete Product(s)

Top cover tape

No components

500mm min

Components No components

Empty components pockets saled with cover tape.

500mm min

User direction of feed

Start

22/24 Doc ID 023692 Rev. 2

VNB35NV04, VNV35NV04 Revision history

Table 11.

Document revision history

Date Revision

19-Sep-2012

17-Sep-2013

1

2

Changes

Initial release.

VNB35NV04 and VNV35NV04 were previously in document

CD00002200 (Doc ID 7374) revision 5.

Added

Section 3.1: ECOPACK

®

Updated Section 3.2: PowerSO-10 mechanical data

and

Section 3.3: D2PAK mechanical data

Updated disclaimer.

Obsolete Product(s) - Obsolete Product(s)

Doc ID 023692 Rev. 2 23/24

VNB35NV04, VNV35NV04

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice.

All ST products are sold pursuant to ST’s terms and conditions of sale.

Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED

WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS

OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.

ST PRODUCTS ARE NOT DESIGNED OR AUTHORIZED FOR USE IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE

SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B)

AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS

OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT

PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN WRITING OF SUCH USAGE, UNLESS A PRODUCT IS

EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE, AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY

DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS. PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE

DEEMED SUITABLE FOR USE IN AEROSPACE BY THE CORRESPONDING GOVERNMENTAL AGENCY.

Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.

ST and the ST logo are trademarks or registered trademarks of ST in various countries.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -

Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com

24/24 Doc ID 023692 Rev. 2