LED Funstrip DMX

 O
LED Funstrip DMX
User Manual
24-004-3444-00
Rev1.1
GENERAL INSTRUCTIONS
Thanks for your purchasing LED Funstrip DMX lighting equipment, which is available in Warm White(WW)
version. The LED Funstrip DMX is compatible of both DMX & RDM and with 10 channel LED intensity
adjustable. Programs can be updated via RDM interface. It is available in master and slave control connection.
It is easy for users to install and operate.
For the optimum operation and best performance, please read the instruction in this manual carefully and
thoroughly.
WARNINGS
e To protect against high electric shock and injury to person, DO NOT open or dismantle the unit.
* After use, the front panel is extreme hot. Please wait at least 15 min for absolute cool before touching it.
Otherwise, it causes the result of burning.
e NEVER try to repair the unit yourself. Repair by unqualified people could cause damage or mis-operation.
e This device is not suitable for direct mounting on normally flammable surfaces. To keep a minimum 0.2m
safety distance to any flammable materials.
e DO NOT make any inflammable liquids, water or metal objects enter the unit.
* This unit contains no user serviceable parts inside. This unit contains dangerous voltages, always remove
the power plug from the wall socket before any service operation and when not in use for a long time.
e Earth connection is so essential.
е Stop using the unit immediately in the event of serious operation problems and either contact your local
dealer for a check or contact us directly.
PHYSICAL DIMENSIONS
615
128.5
54
130
> 0 woman © ol > TY
Ч IE +< OIEA EEE | « ТГ a | hs
\ 4MI0 E 2 ‘ в
81 78.2
1000
_ 1042 _
a . . . D
RC || uf обед o. О т
GENERAL INSTRUCTIONS
Accessories(Included):
1. The unit power cable (1pcs)
2. Wing screw(2pcs) + Grommet(2pcs) + Washer(2pcs)
3. Mounting Assemble(2pcs)
MAIN FEATURES
* 01,02, 05,10 DMX Channels selection
e Standard DMX 3-pin In/Out
16 built-in programs except for Auto & Full subject to Speed and Dimmer
e 0-100% dimming level
* Standard DMX-512 protocol
® 001 Thru 100 Chase Speed adjustment
* Power failure memory
* LED display window-4 digits Segment Display shows current activity and function state
* On/Off switch
® Fuse protection
INSTALLATION
Before use, make sure whether four screws are secured firmly, if not, please secure them with the screwdriver,
loose 4 screws for lamp replacement.
The unit has also been designed to hold up as user's desire. So you can fix the unit on the holder by the wing
screw. They are placed in the accessory bag, included.
The following installation diagrams are for user reference.
Method 1 Method 2
Г
Note :
Once this unit is for hanging application, it is required to use a safety rope (sold separately, which can hold
at least 10 times the weight of the fixture ) to ensure the mounting safety of the fixture by attached through
the holder.
MAIN FEATURES
Power:
Before plugging your unit in, be sure the resource voltage in your area matches the unit required voltage.
The unit is available in a 230V version only. Because the line voltage may vary from venue to venue, you
should be sure to plug the socket into a matching wall outlet before attempting to operate your unit.
Fuses:
The LED Funstrip DMX electric system is protected by T3.15A 250V 5*20mm. Please see the printing on
the case and these fuses prevent you from overloading damaging your unit. To replace the protective fuse,
use a flat head screwdriver to unscrew the fuse holder. Pull out the old fuse and replace it with a new one.
Insert the fuse back into the slot and tighten. Always replace with exact same type fuse removed unless
otherwise specified by an authorized service technician,
SYSTEM CONNECTION
Maximum amount of this units that may be connected is 16pcs(AC100-120V) or 32pcs(220-240V).
One universe DMX can drive up to 32 pcs of LED Funstrip DMX, please add DMX booster if LED
Funstrip DMX are connected together in line over 32 pcs or data cable over 100M. The connections
may be illuminated as following.
SA-10-LED Te Za
„8 80500050041000000000.044000005555R} ES i 0000000558
1 æ ter eres 2 я к
SA-10-LED 7 CRE
eee Peo eee} {806500606 EE {5660606606003 ans yoessesssse
1 Heese bps ити 2 ; | =
eT en |
SA-10-LED RN E
ooo cocoa ooo ae eee ceca pm men meme yoo ese
1 > Tu su 2 ; 3
2 3 32
SYSTEM CONNECTION 3
Layout Overview
Front Panel Overview
1. Lamp: Totally 10 LEDs* Warm White, 7W
Rear Panel Overview
La a LE)
E A [PE RE
—
: Canon "oca
= re EC =
&- TN bai e Ege
— ba DURE Tg a RT ETRY
Lo]
1. LCD Display
This multi-function display will detail all DMX Address, Chase , Program, Speed activity that pertains to the
current operation mode of the unit.
2. Mode button
This button will call up the unit operation mode between DMX and Chase mode.
3. Menu button
This button will active the different functions in Receive and Chase modes.
Note: In the Chase mode, Menu key is used to only activate Chase Dimmer, Chase Program, Chase Speed,
Fade Time and Lamp Mode. While in the " Receive " mode, only used to only select DMX Address, Channel.
4. UP Key
This button will increase the displayed value in the LED display.
5. Down Key
This button will decrease the displayed value in the LED display.
6. DMX Out
This connector sends your DMX signal through to the next unit.
7. DMX In
This connector accepts your DMX input signal.
8. Power Input:
AC100-240V~50/60Hz, Max15A. The supply power is input into your unit via this connector. Be sure to
always connect to proper voltage.
9. Power Thru:
AC100-240V~50/60Hz, Max15A. This connector sends the supply power to the next unit.
10. Fuse:
F3.15A 250V 5*20mm. These fuses prevent you from overloading damaging your unit. Be sure to always
replace with the exact same type fuse.
11. Power Switch:
Turn on/off the power supply.
Layout Overview
OPERATION MODES
The "LED Funstrip DMX” has two different operation modes. It can be used as a 01, 02, 05,10 channel DMX
dimmer. Tap “Mode” button to switch the operation mode between “Receive Mode” and “Chase Mode”. Please
follow illustrations below to operate the unit in your desired mode.
Mode Parameter Parameter Value Function
Address 001-512 To set the initial DMX receiving address
Channel 01/02/05/10 To set the ID of the fixture
DMX No DMX OFF/Hold/Program To set the status of the fixture when DMX signal is input
Glide OFF/ON To set the output of the DMX Data
Program Full/01--16/AUTO To select a built-in program
Speed 01-100 To set the speed level of the built-in Program
Program | Master 00-100 To set the intensity
Lamp Mode Tungsten/LED To set the mode of Lamp
Fade Time 00-100 To set the speed of the Fadetime
DMX Mode
Use this operation mode only when you are about to use the unit as a DMX dimmer. This function can allow
you set your unit dimmer function as a 01, 02, 05 or 10 channel DMX dimmer and DMX address.
DMX Channel Functions Details
DMX Channel
10 Channel Mode
S Channel Mode
2 Channel Mode
1 Channel Mode
LEDI1 Dimmer
LEDI-LED2 Dimmer
LEDI1-LEDS Dimmer
LEDI-LEDI0 Dimmer
|
2 LED2 Dimmer LED3-LED4 Dimmer | LED6-LED10 Dimmer Program
3 LED3 Dimmer LEDS-LED6 Dimmer Program Speed
4 LED4 Dimmer LED7-LED8 Dimmer Speed Fade Time
5 LEDS Dimmer LED9-LED10 Dimmer Fade Time Lamp Mode
7 LED6 Dimmer | Program Lamp Mode Play Mode
7 LED7 Dimmer | Speed Play Mode Master
1. Selecting DMX Address
Press "MENU" button and select DMX channel address menu after having
activated the Receive Mode. The DMX Address Mode is indicated by
“Address” followed by three digits 001~ 512. You can tap the “UP” and
"DOWN?" buttons to change the DMX Address Value.
Address
mm.
Note: There is no DMX input in the master unit of the connection.
Selecting the DMX Channel
Press "MENU" button and select Channel Mode. The Channel Mode is
indicated by "Channel" followed by two digits 01,02, 05, 10. you can tap
the "UP" and "DOWN" buttons to change the setting from 01, 02, 05 or
10 which you wish to run. This function
NOTE:
: Channel
UI
MODE MENU UP DOWN
Um
1. When CH:01 is displayed, overall channels will be controlled by one DMX channel.
2. When CH:02 is displayed, channel 1 and 2 will be controlled by one DMX channel, channel3 and 4 will
be controlled by one DMX channel, and so forth, channel 9 and 10 will be controlled by another .
3. When CH:05 is displayed, channel1~5 will be controlled by one DMX channel and channel 6~10 will
be controlled by another.
4. When CH:10 is displayed, each channel will be controlled by one DMX channel. This is the factory
default setting.
OPERATION MODES 5
Program Mode:
Use the operation mode only when you are about to use your unit as a channel chaser among of the 01, 02,
05, 10 channel chasers. The unit has 16 built-in programs except for Auto and Full. Of course, you can select
any of these programs to chase for a more dramatic lighting show, and you can also control the speed at
which the set programs will be chased.
1. Setting your desired Chase Program:
Once you have activated the Chase Mode, you can tap the “MENU”
button to select and activate “Chase Program” menu. The chase pattern
is displayed in the LCD by "Program " followed by two digits 01~16 or
only "AUTO"& "FULL" appears. You can tap “UP” and “DOWN” button
to select any of them to run at a single time.
Selecting any program of Program01-16 will activate the selected
program; while selecting “Auto” will automatically play the built-in 16
chase programs. When select “Full” menu, all the LEDs will keep
lighting.
. Chase Speed Menu:
Press "MENU" button to select and activate “Chase Speed”
menu. In this menu, you can adjust the program chase speed.
Use the "UP " and "DOWN" buttons to adjust the chase speed
from 001 thru 100. A set value of 100 will give you the fastest
chase speed(approx.1/10th of a second) . While a set value of
001 will give you the slowest chase speed (once every 30 second.).
. Master (Intensity) Menu:
To adjust the output intensity, you must activate the
Chase Dimmer Menu as the previous step. Press “MENU”
button and select “Chase Dimmer” menu, the LCD will display
“Dimmer” followed by three digits.
Use the "UP" and "DOWN " buttons to adjust the light output
intensity between 000 ~ 100. A set value of 000 will give you
the weakest output intensity and a set value of 100 will give
you the full intensity.
. Lamp Mode Menu:
Press “MENU” button and select “Lamp Mode” menu, the LCD will
display “LampMode Tungdten”, user can press “UP” or “DOWN” button
to switch to “LampMode LED” menu.
. Fade Time Menu:
Press “MENU” button and select “Fade Time” menu, the LCD will
display "FadeTime” followed by three digits, user can press “UP”
or “DOWN” button set the desired Fade time value from 000 to 100.
OPERATION MODES
- Program
MODE MENU UP DOWN
55375
MENU UP
: Speed
1000
Dimmer :
001.
MENU ue
~ Dimmer |
100;
MENU UP
q E pora:
LampMode
LED
MENU UP DOWN
Fe 23 Fr
‘FadeTime |
000
LED Funstrip DMX RDM Parameter IDs
Table 1: LED Funstrip DMX RDM Parameter IDs
The following tables outline and describe all the RDM parameters IDs associated with LED Funstrip DMX.
LED Funstrip DMX
UID
MSB of ESTA LSB of ESTA MSB of LSB of MSB of LSB of
50H 41H O1H 01H Unique Seg. Unique Seg.
Model 1D 0x7000 Product Category 0x0509
Manufacturer oxo
Model Description LED Funstrip DMX LED Light
Supported PIDs
Get SET RDM Parameter ID’s Value Comment Implemented
Allowed | Allowed
Category — Network Management
DISC_UNIQUE_BRANCH 0x0001 У
DISC_MUTE 0x0002 У
DISC_UN_MUTE 0x0003 У
v PROXIED_ DEVICES 0x0010
У PROXIED DEVICE COUNT 0x0011
Y У COMMS_STATUS 0x0015
Category - Status Collection
у QUEUED_MESSAGE 0x0020 /
У STATUS MESSAGES 0x0030 v
Y STATUS _ID DESCRIPTION 0x0031 Y
У CLEAR STATUS ID 0x0032 У
У v SUB_DEVICE STATUS REPORT _THR | 0x0033
ESHOLD
Category - RDM Information
У SUPPORTED PARAMETERS Ox0050 | * Support required only if У
supporting Parameters
beyond the minimum
required set.
У PARAMETER DESCRIPTION 0x0051 | - Support required for У
Manufacturer-Specific PIDs
exposed in SUPPORTED _
PARAMETERS message.
Category — Product Information
У DEVICE_INFO 0x0060 4
У PRODUCT_DETAIL_ID_LIST 0x0070
У DEVICE_MODEL_DESCRIPTION 0x0080 У
У MANUFACTURER LABEL 0x0081 Y
“ v DEVICE_LABEL 0x0082 У
У У FACTORY DEFAULTS 0x0090
У LANGUAGE CAPABILITIES 0x00A0
Y У LANGUAGE 0x00BO
4 SOFTWARE_VERSION LABEL 0x00CO0 У
У BOOT_SOFTWARE_VERSION_ID 0x00C1
У BOOT_SOFTWARE_VERSION LABEL | 0x00C2
RDM PARAMETER IDS 7
Table 1: LED Funstrip DMX
RDM Parameter IDs
Get SET RDM Parameter ID’s Value Comment Implemented
Allowed | Allowed
Category - DMX512 Setup
У Y DMX_PERSONALITY ОхООЕО Y
У DMX_PERSONALITY_DESCRIPTION Ox00E1 У
У У DMX_START ADDRESS 0x00F0 * Required if device uses a У
DMX Slot
SLOT_INFO 0x0120 У
v SLOT_DESCRIPTION 0x0121 Y
Y DEFAULT_SLOT_ VALUE 0x0122
Category — Sensors 0x02xx
У SENSOR_DEFINITION 0x0200
Y У SENSOR_VALUE 0x0201
Y RECORD_SENSORS 0x0202
Category — Dimmer Settings 0x03xx Future
Category — Power/Lamp Settings 0x04xx
У v DEVICE HOURS 0x0400
У У LAMP HOURS 0x0401
У Y LAMP_STRIKES 0x0402
У У LAMP _ STATE 0x0403
v Y LAMP_ON MODE 0x0404
У У DEVICE POWER CYCLES 0x0405
Category - Display Settings OxO5xx
Y У DISPLAY INVERT 0x0500
Y Y DISPLAY LEVEL 0x0501
Category — Configuration 0x06xx
У У PAN_INVERT 0x0600
v У TILT INVERT 0x0601
У 4 PAN TILT SWAP 0x0602
У У REAL _TIME_CLOCK 0x0603
Category — Control 0x10xx
У У IDENTIFY DEVICE 0x1000 У
У RESET DEVICE 0x1001
У v POWER STATE 0x1010
Y У PERFORM_SELFTEST 0x1020
У SELF_TEST DESCRIPTION 0x1021
Y CAPTURE PRESET 0x1030
У У PRESET PLAYBACK 0x1031
RDM PARAMETER IDS
Table 2: LED Funstrip DMX Manufacturer Status IDs
Manufacturer Defined Status IDs
Manufacturer Specific messages are in the range of 0x8000 —0xFFDF. Each Manufacturer-specific
Status ID shall have a unique meaning, which shall be consistent across all products having a given
Manufacturer ID. See Table B-2, ANSI E1.20-2010
Status Message ID | value | DataValue1| Data Value 2 Status ID Description
8100H 00H 00H ALL OK
Table 3: LED Funstrip DMX Manufacturer Specific PIDs
Manufacturer Specific PIDs
Manufacturer Defind PIDs range is 0x8000-0xffdf. See Table A-3, ANSI E1.20-2010
ed Fi RDM Parameter TYPE LENGTH | UNIT |PREFIX | MIN | MAX | DEFAULT | DESCRIPTION
у” У” ВАО8Н us 1 NONE| NONE | 0 | 18 1 chase program
у у” 8AO9H US 1 NONE| NONE | 1 99 1 chase speed
У” У” 8A01H US 4 NONE! NONE | 0 4 1 chase dimmer
У” У” 8A42H us 1 NONE| NONE | 4 2 1 lamp mode
и у” 8AOBH US 1 NONE| NONE | 9 100 0 fade time percent
MANUFACTURER STATUS IDS
PROGRAM UPDATE
Programs of this device can be updated via the RDM interface with proper tool named SC-NODE
and RDM Program Tool. Connect the LED Funstrip DMX to the output terminal of the SC-NODE then
connect the SC-NODE to the PC, run the TCP/IP setting, see the following figures for details.
You can get IF settings assigned autcmatically it your network supports ; ue
this capahility Mherwise you need to ask your network administrator for UE
the appropriate IP settings. a
¢_+ Obtain an IP address automatically
5 és Use the folowing IP address: Fe pan ao Eli = ea
IP address nr.
Default gateway.
Eras ót Meves:
37 Use the fotowinag DNS server acdresses: 0 ee
Fieferred DNS server. : :
ect Os: 10 ice CIE}
Alternate DNS server:
Arena En
fr i i “Hos Kane, sheguigs A146 Небо a
| Advanced... | 3 ` i =
| ox J] Coed]
After the TCP/IP is set, run the RDM_Program_Tool.exe software, the tool will search RDM devices
automatically for the first time, user may also search devices via ArtTod Control command.
When the software searched a RDM device, the RDM UID will be listed in the “RDM UID Lists”. Select the
listing RDM UID, then press “Update Selected Device” command to upload the desired updating program,
press “open”command to start updating. After finishing updating, the software will start to search device once
again, and showing “update successfull”, means program updating completed.
he i ; Rn AER AR A AS HAE EE eR AR
ei Or ently
Fly van VARIE FF eras 25
Flan gone inch Eten = Lar E a 2 bors Miter cringe Eta Hair 2430
Ч НУР К - = 3 X Le A о
CET Epes SRA. E ; daa cll
10 PROGRAM UPDATE
TECHNICAL SPECIFICATIONS
AC100~240V,50/60Hz
Power Thru/lnput
IP Rating IP20
Power Consumption 90W
Weight 6.3Kg
Fuse T3.15A 250V 5*20mm
Dimension 1040(L)*130(W)*140(H)mm.
Please note: Specifications and improvements in the design of this product and this manual are subject to
change without any prior notice.
Explanation For The Label
Indicating that the ambient temperature should not be above 35 degrees.
Minimum safety distance to lighted object: 1m.
SPECIAL NOTE
This fixture can be easily mounted with the provided mount assemble, meanwhile a safety rope(sold separately)
is always required to ensure the mounting safety of the fixture by attached and fastened through safety chain
/cord attachment point. This safety rope can hold at least 10 times the weight of the fixture and with a screw
SafetAchain/cord
attachment point
Mount Assemble
on it.
Mount Assemble
TECHNICAL SPECIFICATIONS 11