advertisement
Thank for purchasing our products. We will provide professional guidance and suggestion to you.
Five year warranty is offered from the date of purchase. If there are any quality problems occur during the use of the product, please contact our customer service, and we will provide you with the best after-sales service.
If this product is purchased from second-hand stores or other channels
(non-original channels), our company bears no responsibility to the warranty. For part needs, please contact us to buy.
TIPS: Cleaning & Maintenance Do not use acid detergent, insoluble & grain-like detergent or soap
CUSTOMER SERVICE CONTACT INFORMATION BELOW ：
Wayfair: [email protected]
Overstock: [email protected]
Lowes: [email protected]
Homedepot:[email protected]
8. THE PROCEDURE OF SEALING THE WALL
1. Use a parallel ruler to make sure the wall and valve being parallel.
2. Use a knife to cut the rest of plastic edge.
3"
2.2"
Tile surface
9. INSTALLATION OF CONTROL VALVE
1. Take off the protective panel and cover.
2. The decorative panel and the handle are connected to the control valve as shown below sequence.
Using Allen key to tight the screw
Wall Plastic edge above the tiles
8
According to the figure below, please correctly adjust the direction of water separator handle.
Top shower outlet water
Handle shower outlet water
9
10. SHOWER SETS INSTALLATION
FOR WALL MOUNTED
SHOWER ARM
Option
1
Use the cloth or kraft paper to cover one part of the spout, and then use wrench to clip on the cloth or kraft paper to turn and fix the spout or shower arm into the wall
Option
2
Turn clockwish use a circular arc to form a force point ,and fix the water outtle into the wall
10
12. ADJUSTMENT OF CHECK VALVES
The outlet water adjusting device of the left and right sides, it can adjust the water flow rate and close outlet water function when you need to repair/change cartridge.
Please don' t take out the cloth or kraft paper to use wrench to clip on the spout directly
11. HANDLE SHOWER INSTALLATION
11
It can close water when you screw clockwisely slotted screwdriver on both sides.
Note: If only close one side that it will cause faucet abnormal outlet water, for normal outlet water please make sure the adjusting position on both sides is open (counterclockwise to open).
13. PRODUCT REPARATION
If the cartridge is worn out which cause leakage, please turn off the water source. Remove the handle, panel, and decorative cover in sequence, remove the gland with a wrench, then take out the cartridge and copper sleeve.
Repair or replace the new cartridge, then install it again in sequence.
14. CLEARANCE AND MAINTENANCE
In order to keep the faucet appearance smooth and good performance, please follow the below steps to clean and maintain the faucet.
1. Clean with water and dry with a soft cotton cloth;
2. Use mild liquid and colorless glass cleaner to remove surface dirt and scale, also you can use the cleaner without grinding function.
3. Do not use detergents, polishing tools, abrasive cloth, paper towels or scrapers to clean the faucet
4. Do not use acid cleaners, insoluble granular detergents, soaps, etc to clean the faucet.
12
808006-A08056-20210719
1. INSTALLATION PRECAUTIONS
1. When you open the product packaging, please check the product and accessories at first. If there is any discrepancy, please contact the company or our distributor immediately.
2. The hot and cold water supply pipe of the faucet must be properly connected.
When facing the front of the faucet, the hot water supply is on the left and cold water supply is on the right. Incorrect connection will cause permanent damage to the cartridge.
3. If the accessories to be changed without affecting the use, we will not make a prior notice.
4. The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5. The water pressure of the faucet is 0.05MPa-1.0MPa
(including cold water and hot water pressure).
Applicable water temperature range: 39 ℉ - 194 ℉
3. TWO FUNCTION CONCEALED FAUCET
ACCESSORIES LIST
11
10
12
13
14
2. PREPARATION BEFORE INSTALLATION
1. Please read the installation manual carefully before installation.
2. Installation work must be performed by a professional installer.
3. Installation tool ：
1
1
2
3
5
4
Number
1
2
3
4
9
10
7
8
5
6
11
12
13
14
Description
In-wall box
Control valve
Cover board on/off handle
Diverter handle
Shower hose
Shower hook
Handle shower
Shower head
Shower arm
Cover arm
Screw set
Reducer
Ptfe tape
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
9
8
7
6
4. TECHNICAL DRAWING OF PRODUCT
9.8"x9.8"
5.9"
3
2.2" L 3"
4-1/2-14NPT
4
14"
5. TECHNICAL DRAWING OF DRILLING SIZE
1. The size of the embedded box that needs to be drilled is 5.2"*6.3".
5.2"
6. PIPE CONNECTION
1. Please drill the holes on the wall for the main body embedded part, hot and cold water inlet pipes as well as shower arm connection pipes according to the basic product dimension drawing as below.
2. Please make hot and cold water inlet pipe, the mixed water outlet pipe connect with control valve,and tighten with the wrench.
Be sure to discharge the sewage in the pipe before connecting the water supply pipe, avoid clogging and damage the valve cartridge caused by impurities.
7. WATER TESTING AND SEALING TESTING
1. After the pipe connection is completed, open the protective panel and cover, and then open the cartridge, flush the pipeline; then close the cartridge to check the pressure resistance and sealing performance of the pipeline, make sure there are no leakage.
2. Block each outlet pipe with a stopper then open the cartridge to check if the pipe joint is well-sealed and the pipe condition under pressure to ensure no leakage.
Testing Purpose: Flush the impurities and sludge in the pipeline to avoid clogging and affect the effluent functions.
2. The depth of the embedded box is 2.2"~3".
It's better to drill the depth of 2.2"for blank wall.
3"
2.2"
Tile surface wall
Top shower outlet water
Hot water Cold water
5
Handle shower outlet water
6
Hot water
Top shower outlet water
Cold water
7
Handle shower outlet water
advertisement
Related manuals
advertisement