GIVING TREE XLHDDOTU0108 Single-Handle 2-Spray Round High Pressure Shower Faucet installation Guide
Add to My manuals2 Pages
GIVING TREE XLHDDOTU0108 will help you showcase your bathroom with a clean and modern design, while providing reliable performance. The concealed faucet is a functional work of art that will enhance your bathing experience. The well-crafted construction and simple operation will provide convenience and reliability for years to come.
advertisement
Installation Manual
7ZRIXQFWLRQSUHVVXUHEDODQFHFRQFHDOHGIDXFHW
Unit: inch
6"
4 、
Technical drawing of product
13.8"
1/2-14NPT
1/2-14NPT
1.8"~2.4"
2-1/2-14NPT
2-1/2-14NPT
1.
When you open the product packaging, please check the product and accessories at first. If there is any discrepancy, please contact us.
2.
c connected.
When facing the front of the faucet, the hot water supply is on the left and cold water supply is on the right. Incorrect connection will cause permanent damage to the cartridge.
3.
If the accessories to be changed without affecting the use, we will not make a prior notice.
4.
The impurities in the water supply pipe must be cleared before installation to avoid blockage.
5.
The water pressure of the faucet is 0.05MPa-1.0MPa (including cold water and hot water pressure).
Applicable water temperature range: 39 ℉ - 194 ℉
2 、
Preparation before installation
1 .
Please read the installation manual carefully before installation.
2 .
Installation work must be performed by a professional installer.
3 .
Installation tool :
5 、
Technical drawing of drilling size
1 、 The size of the embedded box that needs to be drilled
is 5.3"*6.7".
5.3"
1
3 、
Two function concealed faucet accessories list
10
13
12
11 9
1 2
3
Number
1
2
3
4
5
6
7
8
9
10
11
12
13
Description control valve
Protective cover cover board diverter handle on/off handle
Shower hose
Elbow with hook
Handle shower
Shower head
Shower arm
Cover board
Screw set
Allen key
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
7
8
6
2
6 、
Pipe connection
1 、 Please drill the holes on the wall for the main body embedded part, hot and cold water inlet pipes as well as shower arm connection pipes according to the basic product dimension drawing as below.
2 、 Please make hot and cold water inlet pipe, the mixed water outlet
pipe connect with control valve,and tighten with the wrench
3
Top shower outlet water
Hot water
2 、 The depth of the embedded box is 1.8"-2.2".
It's better to drill the depth of 1.8"for blank wall.
2.2"
Handle shower outlet water wall cold water
Tile surface
4 5
7 、
Water testing and sealing testing
1 、 After the pipe connection is completed, open the protective panel
and cover, and then open the cartridge, flush the pipeline;
then close the cartridge to check the pressure resistance and sealing
performance of the pipeline, make sure there are no leakage.
2 、 Block each outlet pipe with a stopper then open the cartridge to
check if the pipe joint is well-sealed and the pipe condition under
pressure to ensure no leakage.
Testing Purpose: Flush the impurities and sludge in the pipeline
to avoid clogging and affect the effluent functions.
8 、
The procedure of sealing the wall
Use a parallel ruler to measure the flatness of the embedded box
casing and the vertical wall surface. If the wall surface is not flat,
it should be patched to ensure the embedded box casing and vertical
wall angle meets at nearly ideal angle of 90, then lay the tile decoration.
10
、
Shower sets installation
6
9
9 、
Installation of control valve
1 、
Take off the protective panel and cover
2 、 The decorative panel and the handle are connected to
the control valve as shown below sequence.
wall
11
、
Handle
Tile surface
Protective cover is roughly even with tile
shower installation
According to the figure below, please correctly adjust the direction of water separator handle
Top shower outlet water
Handle shower outlet water
7 8
1 2 、
Product reparation
If the cartridge is worn out which cause leakage, please turn
off the water source. Remove the handle, panel, and decorative
cover in sequence, remove the gland with a wrench, then take
out the cartridge and copper sleeve.
Repair or replace the new cartridge, then install it again in sequence.
1 3 、
Clearance and Maintenance
In order to keep the faucet appearance smooth and good
performance, please follow the below steps to clean and
maintain the faucet.
1 、 Clean with water and dry with a soft cotton cloth ;
2 、 Use a mild liquid and a colorless glass cleaner to remove surface
dirt and scale, also you can use the cleaner without grinding function.
3 、 Do not use detergents, polishing tools, abrasive cloth, paper towels
or scrapers to clean the faucet.
4 、 Do not use acid cleaners, insoluble granular detergents, soaps, etc
to clean the faucet.
1 1
advertisement