advertisement
Y
Parts Included:
New Aeron
®
Pivot Only Arm Casting Replacement
Adjustable Arm Casting
Tools Required:
Bushing Adjustable Arm
Attachment Hardware Assembly
Steel Strip
Lever Assembly
Ratchet Wrench
Steps:
M5 Hex Bit Torque Wrench
T27,T25 Torx Driver T27Torx Bit
1. Remove the back bolts using 5mm Hex bit.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
2. Remove four bolts.
Part no. 1BH0L3 rev B.
1
3. Detach the back from the chair.
4. Remove the screw to detach the arm pad for adjustable arm. Use T25 Torx bit to remove the screw.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
5. Lift the pad on the front and slide backwards as shown above to disengage it from the arm support.
Part no. 1BH0L3 rev B.
2
6. Detach the arm pad.
7. Remove the screw to detach the hardware assembly.
8. Use T27 Torx bit to remove the screws.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BH0L3 rev B.
3
9. Detach the pivot plate.
10. Detach the bottom support.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BH0L3 rev B.
4
11. Detach the arm pad support.
12. Detach the friction pad.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
13. Detaching adjustable arm casting form the swing arm.
Part no. 1BH0L3 rev B.
5
14. Remove the bolt from the swing arm using T27 torx driver.
15. Detach the arm and hardware attachment assembly. Note: Right hand shown has RH threads and a yellow bolt. The left hand arm has LH threads and a black bolt.
16. Remove the steel strip.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
17. Detach the arm casting.
Part no. 1BH0L3 rev B.
6
Re-Assembly Steps:
18. Place the lever assembly into the socket.
19. Attention: Lever should be in fully locked position during installation.
20. Attach the clip in the arm slot as shown.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BH0L3 rev B.
7
21. Place the steel strip in place.
22. Install the arm assembly into the swing arm.
Attention: Keep the arm in vertically centre with the swing arm.
23. Install the hardware assembly as received.
Attention: Do not open the assembly. Follow the above orientation if sub-assembly is disoriented.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
24. Install the bolt with 35 inlbs torque using T27 torxbit.
Attention: Right hand arm shown has RH threads and a yellow bolt.
Part no. 1BH0L3 rev B.
8
25. Follow previous steps to install left hand arm.
Attention: Left hand arm has
LH threads and a black bolt.
26. Replace the arm pad support
27. Replace the bottom support.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
28. Replace the pivot plate in place.
Part no. 1BH0L3 rev B.
9
29. Tighten the screws using the T27 torx wrench. Torque each screw to 110 in-lbs.
30. Slide the rear of the arm pad pocket over tab on arm support. Rotate front of arm down into position.
31. Align the filler plate hole with the slider bar. Use T25 torx bit to install the screw.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
32. Install back assembly.
Part no. 1BH0L3 rev B.
10
33. Install four back bolts using a torque wrench and a 5 mm hex bit. Torque each bolt to 150 in-lbs.
Z
© 2016 Herman Miller, Inc. Zeeland, Michigan. Printed in the U.S.A.
® Y , Z , Aeron are among the registered trademarks of Herman Miller, Inc.
TM Sense, Setu, and Tu are among the trademarks of Herman Miller, Inc.
Illustrations and specifications are based on the latest product information available at the time of publication.
The right is reserved to make changes in design and specifications at any time, without notice, and also to discontinue products.
Part no. 1BH0L3 rev B.
11
advertisement
Related manuals
advertisement