Electric Vehicle AC Charger
Installation Instructions
USER MANUAL
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS ........................................... 2
2. PRODUCT INTRODUCTIONS .............................................................. 6
3. VERIFY CONTENTS ................................................................................ 8
4. GATHER TOOLS..................................................................................... 10
5. PLAN THE MOUNTING ........................................................................ 11
6. MOUNT THE CHARGING STATION ................................................ 13
7. WIRE THE CIRCUIT............................................................................... 15
8. OPERATE YOUR DEVICE ................................................................... 16
9. LIGHT CODES ......................................................................................... 20
10. WARRANTY AND MAINTENANCE .................................................. 21
1
USER MANUAL
II
WARNING & CAUTION
1. Important Safety Instructions
1.1 Overall Warnings & Cautions
WARNING: To avoid fire, injury or death, carefully read and follow the instructions
during installation, operation and maintenance.
-
DO NOT put fingers into the electric vehicle connector.
-
DO NOT use this product if the flexible power cord or EV cable is frayed,
insulation-broken, or any other signs of damage.
-
DO NOT use this product if the enclosure or the EV connector is broken, cracked,
open, or shows any other indication of damage.
-
DO NOT remove cover or attempt to open the enclosure because of risk of electric
shock.
WARNING: This device should be supervised when used around children.
WARNING: This device must be grounded.
WARNING: To avoid a risk of fire or electric shock, do not use this device with an
extension cord.
WARNING: The suitability of the use of flexible cord in accordance with CE code, part
I, rule 4-012, is to be determined by the local inspection authority.
WARNING: To reduce the risk of fire, connect only to a circuit provided branch circuit
over-current protection in accordance with the CSA C22.1–15 Canadian Electrical
Code, Part 1 (Canada) or NOM-001-SEDE Electrical installations (utility) (Mexico) or
ANSI / NFPA 70 National Electrical Code (USA).
Circuit Breaker Options table
Output Amperage (A)
16A
32A
40A
48A
70A
80A
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
2
USER MANUAL
WARNING & CAUTION
1.2 Installation Requirements
WARNING: Disconnect electrical power prior to installing the charging station.
WARNING: Be sure to preview the user manual and ensure local building and
electrical codes are reviewed before installing the AC charger.
WARNING: The AC charger should be installed by a qualified technician according to
the user manual and local safety regulations.
CAUTION: Use appropriate protection when connecting to the main power
distribution cable.
CAUTION: Type B, C or D breaker with the rating current for table should be installed
in the upstream AC distribution box.
CAUTION: The device shall be mounted at height between 2 feet and 4 feet from
ground.
CAUTION: Please keep the charger in a clean area with low humidity. Not
recommended to be installed in coastal environments with high humidity or high dust.
1.3 Daily Maintenance
CAUTION: Avoid moisture or water in the charger. If there is water or moisture
ingress in the charger, it is necessary to immediately power off to avoid immediate
danger, and notify the professionals to carry out maintenance before next use.
CAUTION: Please use the charger properly. Do not hit or press hard on the
enclosure. If it is damaged, please contact a professional technician.
CAUTION: Avoid placing the charger near hot objects and at high temperature
locations and away from dangerous substances such as flammable gases and
corrosive materials.
CAUTION: Do not put heavy objects on the charger to avoid danger.
3
USER MANUAL
WARNING & CAUTION
Consignes De Sécurité Importantes
1.1 Avertissement & Mise En Garde Généraux
AVERTISSEMENT : Pour éviter les risques d’incendie, de blessure ou de mort, il faut
lire et suivre soigneusement les instructions pendant l’installation, l’utilisation et
l’entretien.
Ne mettez pas les doigts dans le connecteur du véhicule électrique.
N'utilisez pas ce produit si le cordon d'alimentation flexible ou le câble EV est
effiloché, isolé ou présentant tout autre signe de dommage.
N'utilisez pas ce produit si le boîtier ou le connecteur EV est cassé, fissuré,
ouvert ou montre toute autre indication de dommage.
Ne retirez pas le couvercle et n'essayez pas d'ouvrir le boîtier en raison du risque de
choc électrique.
AVERTISSEMENT : Cet appareil doit être surveillé lorsqu'il est utilisé à proximité
d'enfants.
AVERTISSEMENT : Cet appareil doit être mis à la terre.
AVERTISSEMENT : Pour éviter tout risque d'incendie ou de choc électrique, n'utilisez
pas cet appareil avec une rallonge électrique.
AVERTISSEMENT : L'adéquation de l'utilisation du cordon flexible conformément au
code ce, partie i, règle 4-012, doit être déterminée par l'autorité d'inspection locale
compétente.
AVERTISSEMENT : Pour réduire les risques d'incendie, ne connecter qu'à un circuit
protection contre les surintensités des circuits de dérivation conformément à la norme
canadienne CSA C22.1-15 Code électrique, partie 1 (Canada) ou NOM-001-SEDE
Installations électriques (Mexique) ou ANSI / NFPA 70 National Electrical Code
(États-Unis).
Circuit Breaker Options table
Output Amperage (A)
16A
32A
40A
48A
70A
80A
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
4
USER MANUAL
WARNING & CAUTION
1.2 Exigence Avant L’installation
AVERTISSEMENT : Assurez-vous de consulter le manuel d'utilisation et assurez-vous
que les codes locaux du bâtiment et de l'électricité sont passés en revue avant
d'installer le chargeur.
AVERTISSEMENT : Débranchez l'alimentation électrique avant d'installer la station de
charge.
AVERTISSEMENT : Le chargeur CA doit être installé par un technicien qualifié
conformément au manuel d'utilisation et aux réglementations de sécurité locales.
MISE EN GARDE : Utilisez une protection appropriée lors de la connexion au câble de
distribution d'alimentation principal.
MISE EN GARDE : Un disjoncteur de type B, C ou D avec le courant nominal indiqué
dans le tableau doit être installé dans le boîtier de distribution CA en amont.
MISE EN GARDE : Cet appareil doit être monté à une hauteur entre 2 feet and 4 feet
du sol.
MISE EN GARDE : Veuillez conserver le chargeur dans un endroit propre et peu
humide. Il n’est pas recommandé de l'installer dans des environnements côtiers à forte
humidité ou à forte poussière
1.3 Entretien Quotidien
MISE EN GARDE : Évitez l'humidité ou l'eau dans le chargeur. En cas d'infiltration
d'eau ou d'humidité dans le chargeur, il est nécessaire de l'éteindre immédiatement
pour éviter tout danger immédiat et d'avertir le personnel professionnel d'effectuer
l'entretien avant la prochaine utilisation.
MISE EN GARDE : Veuillez utiliser le chargeur correctement. Ne frappez pas ou
n'appuyez pas trop fort sur le boîtier. Si le boîtier est endommagé, veuillez contacter
un technicien professionnel.
MISE EN GARDE : Évitez de placer le chargeur à proximité d'objets chauds et à des
endroits à haute température et loin de substances dangereuses telles que des gaz
inflammables et des matériaux corrosifs.
MISE EN GARDE : Ne placez pas d'objets lourds sur le chargeur pour éviter tout
danger.
5
USER MANUAL
2. Product Introductions
CAUTION: Avoid placing the charger near hot objects and at high
temperature locations and away from dangerous substances such as
flammable gases and corrosive materials.
2.1 Basic Interface
4.3” LCD Screen
2.2 Basic Dimension
Enclosure
LED Light Indication
RFID Card
SAE J1772 AC Charging
Connector
Rear Notch
Charging Cable Inlet
Wall-Mounted Bracket
LAN Cable Inlet
AC Power Inlet
6
USER MANUAL
2.3 Specifications
Model Number
JNT-EVC Version
Rated Input Voltage
208/240VAC
Rated Output Current
16/32/40/48/70/80A
AC Power Frequency
50-60 Hz
Input Protection
UVP, OVP, RCD, SPD, Ground Fault Protection
Output Protection
OCP, OTP, Control Pilot Fault Protection
Output Interface
SAE J1772AC Charging Connector
Storage Temperature
-40°F to 158°F
Operation Temperature
-22°F to 122°F
Relative Operation Humidity
95% RH Maximum
Relative Storage Humidity
95% RH Maximum
Network Connection
LAN Version /Wi-Fi Version/4G version
Internet Function
10M / 100M Base-T
Wi-Fi Function
802.11 b/g/n
3G/4G Function
GSM/4G
Cable Length
18ft (25ft optional)
Protection Level
Type 3
Installation Type
Wall-Mounted
Altitude
Status Indication
7
≤ 6561ft
Red, Green, Blue LED
USER MANUAL
3. Verify Contents
Check the box to ensure you have this installation guide and these parts:
1
2
4
5
7
3
6
8
8
USER MANUAL
No.
1
Product Name
AC Charger
Quantity
Description
1
With attached input power cable
and output charging cable
2
User Manual
1
Please read carefully before use
3
Wall-Mounted Bracket
1
For mounting the charging station to
the wall/structure
4
M5 Anti-Theft Round
2
Head Screws
5
M6 Hexagonal Expansion
the Mounting Bracket
4
Screws
For installing the Mounting Bracket
to the wall/structure
6
Allen Wrench
1
For tightening M5 Screws
7
Corrugated Mounting
1
For easy drilling of 4 screws holes
Template
8
9
For securing the charging station to
RFID Card (Optional)
for wall-mounted bracket.
2
Control the charger start/stop
USER MANUAL
4. Gather Tools
Tools required before installing the Wall-Mounted charger, gather the following tools:
1. Wire stripper
2. Adjustable Wrench
3. Voltmeter or digital multi-meter (for measuring AC voltage at the installation site)
4. Level
5. Pencil or marker
6. Drill
7. Phillips screwdriver
1
4
2
5
3
6
7
Note: The above tools are very important, please gather them all.
10
USER MANUAL
5. Plan The Mounting
WARNING: In areas with frequent thunderstorms, add surge
protection at the service panel for all circuits. Ensure all power and
ground connections, especially those at the breaker and bus bar, are
clean and tight.
CAUTION: Not recommended to be installed in coastal environments
with high humidity or high dust.
STEP 1 (Only for 4G Version)
Use screwdriver to loosen the 13 fixed screws on the rear
of charger, then remove the front cover (for 4G Version).
STEP 2 (Only for 4G Version)
Insert the SIM card according to the picture's
instruction (for 4G Version).
11
USER MANUAL
STEP 3 (Only for 4G Version)
Tighten 13 screws on the front cover after the front
cover is put back, the
recommended screw torque is 1.0 N.m (9.6 lbf.in) (for 4G
Version).
STEP 4
Select the appropriate mounting location with electrical
capacity:
I.
Ensure the owner has chosen a mounting location
that allows the charging cable to reach the car’s
charging port while still providing slack.
II. The device must be anchored into mounting such
as 3.14’’ x 5.11’’ stud or a solid wall.
III. The device shall be mounted at height between 2 feet and 4 feet from ground.
STEP 5
Drill 4 Screw Holes with a diameter of
0.32’’and a depth of 2.04’’ by using our
mounting template. Please drill screw holes in
the direction of the template arrow.
12
USER MANUAL
6. Mount the Charging Station
STEP 1
Use 4 sets Hexagonal Expansion Screws to secure the wallmounted bracket on the wall. Then level the brackets.
STEP 2
STEP3
Align the rear notch of charger with the
Tighten two M5 anti-theft screws to
wall-mounted bracket and fit the screw
complete the installation.
holes of the right and left side.
13
USER MANUAL
STEP 4
Overall outlook picture after installation.
Wall-mounted cable winding
Optional cable hanging (optional
accessory)
14
USER MANUAL
7. Wire The Circuit
WARNING: This device must be grounded. Disconnect electrical
power prior to installing the charging station.
WARNING: Improper connection of the equipment-grounding
conductor would result in a risk of electric shock. Check with a
qualified electrician or serviceman if you are not sure whether
the product is properly grounded. Do not modify the plug
provided with the product – if it doesn’t fit the outlet, have a
proper outlet installed by a qualified electrician.
CAUTION: Use appropriate protection when connecting to the
main power distribution cable.
For safe use of electricity, please set circuit
breaker protection in the input part of EV Charger
The wiring is not complicated, just need to follow
the instructions below:
Connect the L1 lead to the grid L1, connect the L2
lead to the grid L2, connect the PE lead to the grid PE.
Circuit Breaker Options table
15
Output Amperage (A)
16A
32A
40A
48A
70A
80A
Circuit Breaker Options (A)
20A
40A
50A
60A
90A
100A
USER MANUAL
8. Operate Your Device
WARNING: This device should be supervised when used
around children.
CAUTION: Please use the charger properly. Do not hit or press
hard on the enclosure. If the case is damaged, please contact a
professional technician.
CAUTION: Do not put heavy objects on the charger to avoid
danger.
8.1 Operating Steps with Plug and Charge
STEP 1
Standby Mode: After being powered on,
the lights will be all on, blue light (READY),
green light (CHARGE) and red light (FAULT).
Then the blue light (READY) is constantly on in
standby mode.
16
USER MANUAL
STEP 2
Plug the Charging Connector:
Please plug the charging connector into the
vehicle charging inlet.
STEP 3
Charging: The green light (CHARGE) turns
to flash automatically, charging is in process.
If the red light (FAULT) is on, plug the vehicle
connector again.
If red light is still on, please refer to "Error
and Warning Messages".
STEP 4
Charging finished: When the charging is
finished, the green light (CHARGE) is
constantly on, pull out the charging connector.
17
USER MANUAL
8.2 Operating Steps with RFID (Optional)
CAUTION: Please keep your RFID card properly to avoid
unnecessary loss.
STEP 1
Standby Mode: After power-on, blue light
(READY), green light (CHARGE) and red
light (FAULT) all on. The blue light (READY)
is constantly on when in standby mode.
STEP 2
Ready to charge:
Please plug the charging connector into the
vehicle charging inlet. When the green light
(CHARGE) is constantly on, the user can swipe the
RFID Card
18
USER MANUAL
STEP 3
Swipe the RFID Card:
Swipe the RFID card first and plug in the charging
connector within 120 seconds, otherwise you need
to swipe the RFID card again.
STEP 4
Charging: The green light (CHARGE) turns
to flash automatically, charging is in process.
If the red light (FAULT) is on, plug in the
charging
connector again.
If red light is still on, please refer to "Error
and Warning Messages".
STEP 5
Charging finished:
When the charging is finished or swipe your
RFID card, the green light (CHARGE) is
constantly on. Please press the button on
connector and pull out the charging connector
19
USER MANUAL
9. Light Codes
9.1 After Start UP
Standby,
waiting to plug
in
Waiting to
charge,
communicating
with vehicle
Charging in
progress
Finished
charging
Fault
Solid Blue
Solid Green
Green Blinking
Solid Green
Solid Red
9.2 Error and Warning Messages
Status
Red
Remark
Input OVP
1 flash followed by 3 sec pause
Auto Recover
Input UVP
2 flashes followed by 3 sec pause
Auto Recover
Output OCP
3 flashes followed by 3 sec pause
Auto Recover
OTP
4 flashes followed by 3 sec pause
Auto Recover
RCD Abnormal
5 flashes followed by 3 sec pause
Auto Recover
Ground Fault
6 flashes followed by 3 sec pause
Auto Recover
Control Pilot Fault
Flicker
Auto Recover
Emergency Fault
Constantly Bright
Rotate to Reset Emergency Button
MCU Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Self-Test Fail
Constantly Bright
Contact Customer Service
Relay Self-Test Fail
Constantly Bright
Contact Customer Service
RCD Abnormal Stop Charging
Constantly Bright
Contact Customer Service
Output OCP Stop Charging
Constantly Bright
Contact Customer Service
OTP Stop Charging
Constantly Bright
Contact Customer Service
20
USER MANUAL
10. Warranty and Maintenance
• The warranty period for this charger is three years.
• During the warranty period for any malfunction under normal use according to the
User Manual (to be determined by certified maintenance technicians of sellers), the
product shall be repaired free of charge. Except for the following situations, the charger
shall be subject to the above warranty terms:
1. The warranty certificate cannot be provided or the contents of the warranty
certificate are modified or inconsistent with the label indication of the repaired
product.
2. Those who are unable to provide valid proof of purchase.
3. Those who exceed the manufacturer's specified warranty period.
4. Those who damage the product due to not following the product service instruction
for use, maintenance and storage.
5. Damage or malfunction caused by external object entering.
6. Unauthorized repair, disassembly or modification.
7. Damage caused by force majeure (such as lightning, excessive voltage,
earthquake, fire, flood, etc.).
8. Malfunction and damage caused by other unavoidable external factors. Malfunction
and damage caused by improper use of equipment, such as water or other solutions
entering into the equipment.
9. Malfunction and damage caused by the grid power supply and voltage which is not
specified for use with the charger equipment.
The above guarantees shall be made solely, and no other express or implied warranties
shall be made (including the implied warranties of merchant ability, particular and
applicable reason- ableness and adaptability, etc.) whether in the contract, civil
negligence, or other aspects, the Company shall not be responsible for any special,
incidental or consequential damages.
21
USER MANUAL
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference
received, including interference that may cause undesired operation.
Caution: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at
his own expense.
LTE module：Contians FCC ID:XMR201909EC25AFX
WIFI module：Contians FCC ID:2AC7Z-ESPWROOM32D
To satisfy FCC RF exposure requirements, a separation distance of 20cm or more should be
maintained between the antenna of this device and persons during device operation. To ensure
compliance, operations at closer than this distance is not recommended.
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’
Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitat ion est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage;
2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compr omettre le fonctionnement.
This equipment complies with IC RSS‐102 radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and
your
body.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR‐102 établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale
de 20cm
entre le radiateur et votre corps.
22
">
