Thomson ROC2309 Owner's manual

ROC2309
00131872
Operating Instruction
Mode d'emploi
Bedienungsanleitung
UNIVERSAL
21
in
UNIVERSAL REMOTE CONTROL
Manufactured and commercialised
by HAMA under THOMSON
Trademark license
Télécommande universelle
Universal Fernbedienung
1
2
3
4
5
7
Operating Instructions .......................................................... 01
Mode d‘emploi ....................................................................... 04
Bedienungsanleitung ............................................................. 07
Istruzioni per l‘uso ................................................................. 10
Instrucciones de uso ............................................................. 13
Gebruiksaanwijzing ............................................................... 16
Manual de instruções ............................................................ 19
Οδηγίες χρήσης..................................................................... 22
Руководство по эксплуатации ......................................... 25
Instrukcja obsługi................................................................... 28
Návod k použití ...................................................................... 31
Használati útmutató .............................................................. 34
Bruksanvisning ....................................................................... 37
Brukerveiledning .................................................................... 40
Brugsanvisning ....................................................................... 43
Pistokelaturi............................................................................ 46
6
8
9
10
8
9
11
13
12
14
15
17
16
вес = 80 грамм
Ciężar = 80 g
Hmotnost = 80 g
Súly = 80 gramm
Vikt = 80 gram
Vekt = 80 gram
Vægt = 80 gram
Paino = 80 grammaa
Dimensions - Dimensions - Abmessungen - Dimensioni - Dimensiones
- Afmetingen - Dimensões - Διαστάσεις - размеры - Wymiary - Rozměry
- Méret - Mått - Dimensjoner - Mål - Mitat
= 171 x 49 x 20 mm
This universal remote control (2 in 1) is compatible with the majority of television sets, DVD
players and video recorders, amplifiers and Hi-Fi and Home Cinema systems, as well as
digital boxes such as satellite or cable receivers, DVBT receivers (Digital Video Broadcast
Terrestrial), ADSL decoders, and so on.
This remote control was programmed in the factory, so that you can use it to control most
of the sets of the THOMSON group’s make. For this reason, we recommend that prior to
attempting to programme the remote control, you try it out by means of one of the methods
described in this user manual. However, first of all, you must install 2 batteries (AAA) in the
remote control.
Please keep this guide along with the code list (provided separately), so that you can
subsequently programme your remote control for use with other sets.
corresponds to the type of device, for example: 0603
for a Thomson satellite receiver) and then to run the
automatic search procedure. The remote control will
then test all the codes automatically until it finds those
that control the receiver.
Note 2: To control 2 devices of the same type and the
same brand (2 Thomson VCRs, 2 Thomson satellite
receivers, ...) ensure first that these two devices are not
set to react to the same sub code, they will require one
sub code for one and a different sub code for the other
(i.e., codes A and B with Thomson devices). Once you
have checked this, successively program 2 separate
mode keys using method D.
The keys
1
Indicator light: The red indicator light is lit
whenever a key is pressed.
2
G : On/Standby or Standby only, depending on
the equipment being used.
3
Mode keys: Select the device to control (TV, DVD,
…).
4.
B (play): Play a DVD disc or a VCR tape*.
F (FF): Fast forward (DVD, VCR,...)*.
E (RW): Goes backward (DVD, VCR,...)*.
J (pause): Suspends play and stops on an
image*.
I (record): To record, press the RECORD key
twice.
K (stop): Stop the disc (DVD)*.
: Teletext On.
5.
: Teletext Off.
: Teletext Hold (stop page scrolling).
: Displays information of the selected
appliance.
6
Guide: Electronic Program Guide.
7
Setup: Allows you to program your remote
before the first use.
8
P+/P-: Channel Up and Channel Down buttons.
9.
V+/V-: Increases (+) or decreases (-) the volume
of the selected device.
10. OK: Confirms a selection.
11. C/D/A/B: Allow you to navigate the menus
verticaly and horizontaly.
12. Exit: Turn off the menu of the selected product.
13. H (Mute): Switches the selected appliance sound
off.
14. Menu: Turns on the menu of the selected product.
15. Numeric keys 0-9: These keys have the same
functions as those of your original remote and
are also used to enter the code.
16. :--/-: In connection with the numeric keys, this
button allows you, with some equipment, to select
directly channels with 2 digits.
17. AV: For selecting an external source (SCART,
HDMI, ...)..
Note: depending on the actual devices, manufacturers
and year of manufacture, the functions available
will vary.
* The coloured buttons can be used to select categories
when teletext is activated, and specific functions
depending on the make.
Programming
the remote control
Method A – Fast programming
with 1-digit subcode
Before you start programming, you must find the
subcode of the set to be controlled. Entering a subcode
lets the remote control test a predefined list of codes.
Refer to the list provided with these instructions, page I
of the subcodes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time to
proceed with the following steps. The indicator lamp
flashes to signal that this time is almost up, and then
goes off). Release the SETUP key.
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, Video
recorder, SAT: satellite receiver, cable, DVBT, ADSL
4. While the indicator is lit, type in the subcode
(example: 1 for THOMSON).
5. Direct the remote control towards the set and try to
switch it off by pressing the key G.
6. If the set you want to control switches off, press OK
to memorise the code.
7. Should the set not switch off, press key G repeatedly,
until the set switches off. Between pressing the keys,
be sure to leave enough time for the indicator light to
go out and then relight (about 1 second). Proceeding
this way will enable you to see whether the set
responds or not.
8. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
Testing the remote control before
you programme it
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
1. Switch on the set you want to control.
2. Press the key that corresponds to the type of
equipment you want to control:
TV: Television Set,
DVD: DVD Player, Video Recorder,
SAT: Satellite Receiver, Cable Receiver, ADSL Box,
DVBT Receiver, ...
3. Direct the remote control towards the TV set and
try to switch it off by simply pressing the key G. If
the device does not turn off, you must program the
remote control using one of the methods A, B, C or
D described hereafter.
Method B – 4-digit codes
programming
Before you start programming, you must find the code
of the set to be controlled.
Refer to the list provided with these instructions, page
II of the codes.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time to
proceed with the following steps. The indicator lamp
flashes to signal that this time is almost up, and then
goes off). Release the SETUP key.
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, Video
Note 1: Except for the TV key, the DVD, SAT mode
keys can be programmed to control a device other
than that indicated on the key. It is therefore possible,
for example, to allocate SAT mode to the DVD key. You
must enter the code corresponding to the manufacturer
and the device by using one of the methods indicated
in this manual.
However, method D (automatic search for a code)
will greatly simplify the task for you. In this case it
is only necessary to enter a code from the list that
1
GB
ROC2309
00131872
Method E – Programming for control of a
COMBO (combined TV-VCR, TV/DVD, VCR/
DVD, … set)
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Depending on the COMBO group (TV/VCR, VCR/
DVD, etc.) and the make, you will be required to
enter a single code for both devices in the COMBO,
or to enter two codes, one code per device. Consult
the separate list to discover this. Before you start
programming, you must find the subcode or code
of the subset to be controlled (television or video
recorder...). Refer to the list supplied with this user
manual (see page subcodes or codes).
1. Switch on the COMBO you want to control.
2. Hold the SETUP key down until the red indicator
lamp blinks and then remains lit. Release the
SETUP key.
3. Press the key of the first device to control, and then
follow one of the programming methods A, B, C or
D previously described.
4. If a second code programming is required, then
repeat steps 2 and 3 above.
Method C – Programming by means
of code retrieval
Should none of the codes work, you still have the
possibility of retrieving the appropriate code without
having to perform any input.
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off). Release the SETUP key.
3. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, Video
recorder, SAT: satellite receiver, cable, DVBT,
ADSL
4. Direct the remote control towards the set and try to
switch it off by pressing the key G.
5. If the set you want to control switches off, press
OK to memorise the code.
6. Should the set not switch off, press key G as many
times as required (up to 200 times), until the set
switches off. Between pressing the keys, be sure
to leave enough time for the indicator light to go
out and then relight (about 1 second). Proceeding
this way will enable you to see whether the set
responds or not.
7. Immediately upon the switching-off of the set to be
controlled, press OK to store the code.
How to retrieve
a programmed code
It may be useful to retrieve the code programmed in
the remote control.
1. Hold down the SETUP key until the red indicator
light blinks and then remains lit. Release the SETUP
key.
2. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, Video
recorder, SAT: satellite receiver, cable, DVBT,
ADSL.
3. Press the SETUP key again briefly, the indicator
light blinks once.
4. Press the number keys (0 to 9) until you notice that
the indicator lamp blinks once.
5. The number which made the indicator lamp blink
is the first of the four figures comprising your code,
write it down.
6. Repeat step 3 to find out the 3 other numbers of
the code.
7. When the fourth figure is found, the indicator lamp
goes out.
Check of the programming:
In principle, your set is ready for receiving the remote
control commands.
Check your remote control for proper functioning by
performing the test described on page 2.
Try out other remote control keys to find out the range
of functions you can control. If you think that not all
of the keys are active, repeat the procedure of this
programming method to find out the code supporting a
wider range of features.
Check of
the programming
Method D – Automatic
code search
-
With this method, the remote control scrolls through
the full code list by sending an IR signal to the set to be
controlled remotely. Proceed as follows:
1. Switch on the set you want to control.
2. Hold down the SETUP key until the red indicator
light blinks and then remains lit (the indicator light
remains on for a few seconds to give you the time
to proceed with the following steps. The indicator
lamp flashes to signal that this time is almost up,
and then goes off).
3. Release the SETUP key.
4. Press the key that corresponds to the type of
equipment you want to control:
TV: television set, DVD: DVD player, Video
recorder, SAT: satellite receiver, cable, DVBT,
ADSL
5. Press the P+ or standby G or B (DVD/VCR only)
key. After a few seconds, the remote control begins
to scroll through the whole code list included in the
library (at a rate of roughly 1 code per second).
Press the P+ , G or B key once again to slow
down the test speed (1 code every 3 seconds). As
soon as the set changes channels (or turn off, or
start to play the disk), you must press OK to save
-
For a television or a satellite receiver: switch on
and, for example, press 2 to change channels,
etc...
Video recorder: load a tape and then press B.
DVD player: load a DVD and then press B.
Other functions
Replacing the batteries
Placing all devices on standby
Press the G key twice in less than one second, keeping
it held down the second time. All the devices go on
standby one after the other (the devices which were
already on Standby may turn on).
Use 2 AAA 1.5 Volt batteries
1. Open the cover on the back of the remote control.
2. Check the +/– polarity on the batteries and inside
the compartment.
3. Insert the batteries.
4. Press the battery cover back into place.
When exchanging the batteries, it may be necessary to
reprogram the unit. Hence it is advisable to record the
codes needed for your devices.
Adjustment of ALL volume controls under a
specific mode
In its delivered state, the ROC6309 is programmed
such that all modes will use their own Volume and
Mute functions if present.
You can allocate the volume control to one of the
modes of the remote control on condition that the
volume control exists on the corresponding device
(e.g. control of TV sound in TV mode, DVD mode, VCR
Mode, etc.).
1. Hold the SETUP key down until the red indicator
lamp blinks and then remains lit.
2. Release the SETUP key
3. Press the H key until the red indicator lamp blinks
once.
4. Press once on the mode key (TV, DVD, …)
corresponding to the device whose volume will
always be controlled by the VOL and H keys.
5. Press the H key once. The red indicator lamp goes
off.
6. All other mode will now punch-through to your
chosen mode for Volume and Mute control.
Adjustment of the volume controls for EACH
mode.
You can decide that the volume control is functional
for each mode selected on condition that the volume
control exists on the corresponding device (e.g. control
of the television set sound in TV mode, the control of
the sound of the SAT receiver in SAT mode, …).
1. Hold the SETUP key down until the red indicator
lamp blinks and then remains lit.
2. Release the SETUP key
3. Press the H key until the red indicator lamp blinks
once.
4. Press once on the mode key (TV, DVD, …)
corresponding to the device whose volume will
always be controlled by the VOL and H keys.
5. Press the VOL- key once.
6. Press the H key once. The red indicator lamp goes
off.
7. The chosen mode key will now use its own Volume
and Mute functions
Restoring the universal Volume/Mute
functions
If you have changed the universal volume and mute
functions, as described in the previous two sections,
you can reset the functions back to the factory settings:
1. Hold the SETUP key down until the red indicator
lamp blinks and then remains lit.
2. Release the SETUP key
3. Press the H key until the red indicator lamp blinks
once.
4. Press and release the H key. The red indicator
lamp will go off completely. The volume and mute
functions are now restored to their factory defaults.
Try other remote control keys to find out the range of
functions you can control. If you think that not all of the
keys are active, try the programming Method B or C.
When you have retrieved the code of
your set, jot it down so that you can use it
whenever needed.
After battery replacement, you may have to
programme the remote control again.
TV CODE
2
DVD/SAT CODE
3
GB
GB
the code and stop the remote control scrolling
through the list. If you do not react quickly enough,
you can go back to the previous code by pressing
P- or E (DVD/VCR only) as many times as
necessary (you can go forward by pressing G ,
P+ or B (DVD/VCR only) if you have gone back
too far). As soon as the set responds again, press
OK to save the code.
recorder, SAT: satellite receiver, cable, DVBT, ADSL
and AMP: audio equipment.
4. While the indicator is lit, enter the first digit of the
4-digit code proposed for the set to be controlled
(example: 0036 for Thomson).
5. Direct the remote control towards the set and try to
switch it off by pressing the key G.
6. Should the set not switch off, repeat step 2. Then
type in the next 4-digit code. Try to switch off the set
by pressing key G once. Repeat this procedure by
trying out each of the 4-digit codes.
4
5
F
F
F
-
CODE TV
CODE DVD/SAT
Die Tasten
1
6
7
D
TV-CODE
DVD/SAT-CODE
8
9
D
D
I
I tasti
1
10
11
I
-
I
CODICE TV
CODICE DVD/SAT
12
13
E
14
CÓDIGO TV
CÓDIGO DVD/SAT
15
E
E
NL
16
Methode C - Programmering
via opsporing van de code
17
NL
-
NL
TV-CODE
DVD/SAT-CODE
18
19
P
20
Substituir as pilhas
CÓDIGO TV
CÓDIGO DVD/SAT
21
P
P
GR
22
23
GR
GR
Кнопки
1
24
25
RU
RU
26
Koд TV
RU
27
PL
28
29
PL
-
KOD TV
PL
Tlačítka
1
30
31
CZ
CZ
32
KÓD TV
Jak získat
naprogramovaný kód
CZ
33
5.
6
7
8
9.
10.
11.
12.
13.
14.
15.
16.
17.
H
34
35
H
-
TV KÓD
Knapparna
1
2
3
4.
Elemcsere
H
5.
6
7
8
9.
10.
11.
12.
13.
14.
15.
16.
17.
36
37
S
S
38
KOD TV
S
39
Tastene
1
2
3
4.
5.
6
7
8
9.
10.
11.
12.
13.
14.
15.
16.
17.
N
Metode B - Programmering
av koder med 4 sifre
40
41
N
-
TV-KODE
N
Tasterne
1
42
DK
-
43
Metode E – Programmering for at
betjene en COMBO (kombineret
TV/VCR,TV/DVD,VCR/DVD, osv.)
DK
44
Afprøv de andre taster på fjernbetjeningen for
at kende de funktioner, som Deres fjernbetjening
kan styre. Såfremt De mener, at visse taster ikke er
aktiveret, prøv da en anden programmeringsmetode,
metode B eller C.
TV-KODE
DK
45
5.
6
7
8
9.
10.
11.
12.
13.
14.
15.
16.
17.
SF
46
47
TV-KOODI
SF
SF
48
49