Arctic Spas Spa Quick Reference Guide

PDF
Dokument
Arctic Spas Spa Quick Reference Guide | Manualzz

Werbung

Werbung

How to Connect Your Spa To Your Home Network With WIFI Extender
Quick Reference Guide
#17486
If your Spa Was ordered with a WIFI Extender the WIFI Extender will be

Connected to the Motherboard & Processor Card in the Spa Pack of your Spa

and your Spas Low Level Programming (LLP) settings will be factory set to

Dynamic. Set up to have a Dynamic Internet Protocol (IP) address.

Watch the Video that demonstrates How to Connect Your Tenda Wireless Range

Extender to Your Home Network(WIFI Extender ordered with your Spa)

Following the directions in the Video, connect the WIFI Extender to your

home network

Using your smart phone or tablet go to Settings/WIFI.

Connect to Tenda _XXXXX (Open)

Do you see the WIFI Extender?

Illuminated?

Try another

WIFI Extender

Are all lights illuminated?

Remove the Spas PAK cover, locate the WIFI Extender

check and confirm WIFI Extender power light is

illuminated.If not illuminated ensure the power cable is

correctly installed.

Check home router firewall settings for restrictions. The

router may be set to Block devices “scanning” the network.

Contact your Dealer for assistance.

Connect to the Spa using the LAN button on the App.

Note: It can take up to 6-8 times for the App to find The

Spa on your home network, if need be keep pressing the

reconnect button.

Scroll through the Spas Low Level Programming

(LLP) check to ensure the Spas Internet Protocol

(IP) address.

Access the Spas Low Level Programming (LLP)

through the Topside Controller by holding the

FILTER button down until LLP is displayed.

• Scroll through the LLP settings by pressing the

FILTER button, each time you press the filter button

you move to the next LLP setting, scroll through until

IP is displayed.

•St or dy will be displayed, if St is displayed press the

Up Arrow button to change to dy Dynamic.

• Press the FILTER button again to display the Spas IP

address (Last Octec should appear).

• Continue to press the FILTER button until you have

exited the LLP settings. At this time the Pack will save

the settings.

Doyou have an IP address?

Blocked?

Connected?

Try connecting to

the Spa with another

device.

Unblock router

settings.

Remove the Spas PAK cover, locate the WIFI Extender

check and confirm:

• Power light on WIFI extender is illuminated.

• Ethernet cable is plugged into the RJ45 plug on the

WIFI Extender and light is illuminated.

• Ethernet cable is plugged into the RJ45 plug on the

Processor Card and light directly under the RJ45

plug is illuminated.

If WIFI light is Orange home WIFI signal may

be weak, try the following:

• Relocate WIFI Extender.

• Relocate home router.

Note: If the above does not correct

the problem, contact your Dealer for

assistance.

Try the following one at a time in the bellow

order:

• Different Ethernet cable.

• Reset the WIFI Extender by holding down

the factory reset button for 10 seconds

with a pen.

• New WIFI Extender.

• New Processor Card.

Note: If the above does not correct

the problem, contact your Dealer for

assistance.

YES

YES
NO
YES
NO
YES
NO
NO

YES

NO

YES

YES

Connected?

Connect to the Spa Usingthe LAN

bbutton on the App.

Note: It can take up to 6-8 times

for the App to find the Spa on your

home network, if need be keep

pressing the reconnect button.

Go to the myarcticspas.com webpage to create an

account for your spa and to register you Spa. Refer

Flowchart How to Connect Your Spa to the Myarctic Spas

Server.

Open the Arctic Spas App on your device such as your

Smart Phone or tablet.

Your Spa is now connected to your home network and

you can control your Spa through the App.

NO

NO

The following Supportive Video Link may

also assist you with this process:

http://www.arcticspas.com/support/how-to-videos/

how-to-connect-with-a-tenda-wifi-extender/
How to Connect Your Spa to the My Arctic Spas Server
Quick Reference Guide
New Users must first create a New User Account on the myarcticspa.com Home Page.
To access the My Arctic Spa Home page enter the following web address into your
browser www.myarcticspa.com
To create a New User Account Complete the details in the Register box located on the right
hand side of the Home Page.
Note: Ensure the Password you set is at least seven characters long.
Once completed, press the Click Here to Register button at the bottom of the Register box to
take you to the New User Account screen.
On the New User Account screen, complete all the Required Information fi elds accordingly.
Once completed, press the Register button at the bottom of the New User Account screen.
A pop up message will be displayed advising you that you will receive an
Account Confi rmation Email in a few minutes to complete the registration process.
Open the Email received from [email protected].
Complete the registration process by clicking on the Confi rm my MyArcticSpa.com account:
link in the Email received.
You will be directed to the Account Activation screen on the myarcticspa.com web page and
the confi rmation message will be displayed.
Click the Login link in the Confi rmation Message on the Account Activation screen and
you will be directed to a Login screen.
Enter your user name and password in the fi elds provided in the Login Box.Once entered, press
the Login button directly under the Username and Password fi elds.You will be directed
to the Profi le and Preferences Page, where you can click on the link to register your spa
details.
Click the Register an Arctic Spa link in the Profi le and Preferences box to commence the
spa registration process.
You will automatically be directed to the Register A Spa Page, where
you will need to register your spa details.
Click the Search button to fi nd your spa.
The Spa Registration Confi rmation pop up box will be displayed advising you to press a
button on your Spas Topside Controller to confirm the spa registration.
Note: You have 3 minutes to press a button on your Spas Topside Controller otherwise you will
need to press the search button again.
You must go to your Spa to press any button on the Topside Controller.
“rEG” will be displayed on the Topside Controller. When you press any button on your Spas
Topside Controller “ConF” will be displayed, refl ecting that your spa is being confi rmed for
registration.
On the Register a Spa page you will now be able to see your spa.Press the Register button.
Then enter a nickname for your Spa and the Serial Number of your spa in the Nickname and
Spa Number fi elds on the Register a Spa Page. Press the Register button to complete the
registration process.
Through myarcticspa.com you now have direct access to all
your Spas Functions and Settings from anywhere in the world
where internet access is available through your smart phone,
tablet or computer.#17486
The Spas Serial No. can be located on the Metal Compliance
Plate mounted to your spa just above the Bottom Rail and be-
tween two doors.You only need and register the number portion
of the complete Serial No.Eg Spa Serial No. AX16KX178910,
17890 is the portion of the Serial No. required to be recorded.
NOTE: You will receive a prompt to refl ect that your spa must
be connected to the Internet (Your Home Network). You must
have first connected your spa to your home network
using the App on your device such as a Smart Phone or tablet.
This will have been achieved with a WIFI connection using either
EoP, WIFI Extender or LAN connection.
NOTE: Once you have logged in for the fi rst time and
registered your spa details within myarcticspa.com, logging into
myarcticspa.com is achieved from accessing the My Arctic Spa
home page.
Login by entering your user name and password in the fi elds on
the upper right hand side of the home page.
Once entered press the Login button directly under the
Username and Password fi elds. Once logged in, My Arctic Spa
will automatically open your personal My Arctic Spa page.
You can now login for the First Time
Do the following to Login.
Your Spa is now connected to The My Arctic Spas Server.
The following Supportive Video Link may
also assist you with this process:
http://www.arcticspas.com/support/how-to-videos/
how-to-connect-arctic-spas-to-the-my-arctic-server/
/

Werbung

Dokument wird für den Druck vorbereitet…
0%