5.2.2 Quick Sequence View. Vitek VT-TNR3216PF, VT-TNR818PN, VT-TNR818PFN, VT-TNV128E1, VT-TNV6416E1, VT-TNR818P, VT-TNR818PF, VT-TNR6480E1, VT-TNR3216PFN, VT-TNR1646PF
Add to my manuals186 Pages
advertisement
VITEK Industrial Video Products – Transcendent Series NVRs VITEK Industrial Video Products – Transcendent Series NVRs
Ø
Add Display Mode
Method One:
①
Click “Customize Display Modes” in the above interface
②
Click to add a display mode name and then set the screen mode.
③
Add the cameras and adjust the cameras’ display sequence as required.
④
Click under the display mode list.
Method Two:
①
Click Start
à
Settings
à
System
à
Basic
à
Output Settings to go to the interface and then set the screen mode.
②
Double click the camera or camera group in the list to add them to the selected window.
③
Click to save the current display mode (refer to 5.2.4 Scheme View In Sequence for detail configurations). The display mode will be saved and displayed in the display mode list in the live preview interface.
Ø
Edit Display Mode
Click “Customize Display Modes” tab in the live preview interface and then select one display mode in the list. Click to edit the display mode name; click to delete the display mode.
Ø
Corridor Pattern
Some models may not support this function.
Select corridor pattern in display mode. You can change the direction of the video image by using this function. Please refer to User Manual of relevant camera.
37
Ø
Fisheye Mode
Some models may not support this function.
In the live preview, select the view mode according to the installation mode and display mode of the fisheye camera. Please refer to User Manual of relevant camera.
5.2.2 Quick Sequence View
You can start quick sequence view if the scheme has not been created. If the scheme has been created, please refer to 5.2.4 Scheme View in Sequence for details.
38
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 10 INTRODUCTION
- 21 BASIC OPERATION GUIDE
- 21 2.1.1 Startup
- 21 2.1.2 Shutdown
- 26 WIZARD & MAIN INTERFACE
- 32 3.2.1 Main Interface Introduction
- 35 3.2.2 Setup Panel
- 36 3.2.3 Main Functions
- 38 CAMERA MANAGEMENT
- 38 4.1.1 Add Camera
- 41 4.1.2 Edit Camera
- 42 4.2.1 Add Camera Group
- 43 4.2.2 Edit Camera Group
- 43 4.2.3 IP Planning
- 44 LIVE VIEW INTRODUCTION
- 45 5.2.1 Preview By Display Mode
- 47 5.2.2 Quick Sequence View
- 48 5.2.3 Camera Group View In Sequence
- 49 5.2.4 Scheme View In Sequence
- 53 5.4.1 OSD Settings
- 54 5.4.2 Image Settings
- 54 5.4.3 Mask Settings
- 55 5.4.4 Fisheye Settings
- 55 5.4.5 Image Adjustment
- 68 RECORD & DISK MANAGEMENT
- 68 7.1.1 Mode Configuration
- 70 7.1.2 Schedule Settings
- 73 7.1.3 Advanced Configuration
- 74 7.3.1 Manual Recording
- 74 7.3.2 Timing Recording
- 74 7.3.3 Motion Based Recording
- 74 7.3.4 Sensor Based Recording
- 74 7.3.5 AI Event Recording
- 75 7.4.1 Disk Management
- 78 7.4.2 Storage Mode Configuration
- 79 7.4.3 View Disk and S.M.A.R.T. Information
- 80 PLAYBACK & BACKUP
- 85 8.3.1 Smart Playback Settings
- 86 8.3.2 Smart Playback Based on Motion Detection
- 87 8.3.3 Smart Playback by Face Search
- 88 8.3.4 Smart Search by License Plate
- 89 8.4.1 Search, Playback & Backup by Time-sliced Image
- 91 8.4.2 Search, Playback & Backup by Time
- 92 8.4.3 Search, Playback & Backup by Event
- 93 8.4.4 Search & Playback by Tag
- 93 8.4.5 Image Management
- 94 8.4.6 View Backup Status
- 95 AI EVENT MANAGEMENT