advertisement
RADIO CLONING
CLONING RADIO SETTINGS
You can copy the CLP Series radio settings from one radio (the source) to a second radio using the
CLP Series Single Unit Charger (SUC) Kit P/N
HKPN4008 and CLP Series Cloning Cable Kit
P/N HKKN4026 (optional accessory) or CLP
Series Multi-Unit Charger (MUC) Kit
P/N HKPN4007 (optional accessory).
A multi-channel radio can be cloned to a singlechannel radio BUT only the first channel is cloned.
The Multi-Unit Charger (MUC) does not have to be plugged in for cloning, but both radios require charged batteries .
CLONING INSTRUCTIONS
Cloning Radios using the CLP Series
Cloning Cable Kit P/N HKKN4026 (optional accessory)
Cloning the Radio through a Single
Unit Charger
Source Radio: Radio to be cloned
Target Radio: Radio to which the configuration of the “Source Radio” will be copied.
Before beginning the cloning process, make sure you have:
• A fully charged battery on each one of the radios
• Two CLP Series Single Unit Charger (SUC) Kits
• Both radios are turned OFF
1.
Unplug any cables (power supply or USB cables) from the Single Unit Chargers.
English
24
2.
Plug one side of the cloning cable microconnector to one Single Unit Charger.
Plug the other end to the second Single Unit
Charger.
Note: During the cloning process no power is being applied to the Single Unit Charger. The batteries will not be charged. A data communication is being established between the two radios.
3.
Turn ON the “Target Radio” and place it into one of the Single Unit Chargers.
4.
On the “Source Radio”, power the radio following the sequence below: Press and hold the Push-to-Talk (PTT) and the “-”
Button simultaneously while turning the radio ON until you hear the Cloning Tone and Double Blinking Yellow on the Smart
Status Glow.
5.
Place the “Source Radio” in its Single Unit
Charger with an Audio accessory, then press and release Menu Button to start the cloning process.
6.
After cloning is completed, the “Source
Radio” will sound either a “pass” tone
(cloning was successful) or a “fail” tone
(cloning process has failed). The pass tone sounds like a good key “chirp” whereas the
“fail” tone sounds similar to a “bonk” tone.
(A tone will be heard in no more than 5 seconds).
7.
Once you have completed the cloning process, you should turn the radios “OFF” and “ON” to bring them to normal user mode (exit “clone” mode).
25
English
What to do if cloning fails
The radio will emit an audible “bonk” indicating that the cloning process has failed. In the event that cloning fails, try performing each of the following before trying to start the cloning process again.
1.
Make sure that the radio batteries on both radios are fully charged.
2.
Verify the cloning cable connection on both
Single Unit Chargers.
3.
Make sure that the battery is engaged properly on to the radio.
4.
Make sure that there is no debris in the charging tray or on the radio contacts.
5.
Verify that the source radio is in cloning mode.
6.
Make sure that the radio to be cloned is turned ON.
7.
Make sure that radios are both from the same type (same frequency band, same region and same transmission power).
Note: This cloning cable is designed to operate only with compatible Motorola Drop-in Tray Single Unit
Charger. When ordering the cloning cable, please refer to CLP Series Cloning Cable Kit P/N
HKKN4026. For details about accessories, refer to
"Accessories" Section on page 42.
English
26
Cloning Radios using the CLP Series Multi-
Unit Charger (MUC) Kit P/N HKPN4007
(optional accessory)
Cloning the Radio through a Multi-Unit
Charger
1.
To put the source radio into clone mode, press and hold PTT and the “-” button while turning the radio ON until you hear the
Cloning Tone and Double Blinking Yellow on the Smart Status Glow.
2.
Place the source radio into one of the charging pockets that has the “CLONE” label.
3.
Turn the target radio ON and place it in the pairing charging pocket that has the
“CLONE” label and start the cloning process.
4.
Press the “Menu” button on the source radio to start the cloning process. The source radio generates the start clone tone.
5.
Once the cloning is completed, turn the target radio OFF and back ON again in order to activate the radio.
6.
7.
To clone another radio, repeat steps 3, 4 and
5.
To exit clone mode on the source radio, turn the radio OFF.
27
English
advertisement