- Home
- Domestic appliances
- Climate control
- Split-system air conditioners
- Samsung
- AR24HVSDKWK
- User manual
Disassembling/Assembling the Cover panel for indoor unit installation. Samsung AR24HVSDKWK
Add to My manuals57 Pages
advertisement
• Search for other spots if there are less than two studs, or the distance between the studs are different from the plate hanger.
• Fix the installation plate without inclining to one side.
• Make sure that a wall can withstand the weight of the product. If you install the product in a place where it is not strong enough to withstand the product weight, the unit could fall and cause injury.
Assembling the hanger screw
Use 2 screws to fix the indoor unit with hanger plate as shown in the picture.
Screw
Disassembling/Assembling the Cover panel for indoor unit installation
Please scan this QR code for detail video of indoor unit installation .
In order to install the indoor unit, you must disassemble the cover panel first . Please proceed following instructions to disassemble and assemble the cover panel . Hooks (on the cover panel) may get damaged if you apply excessive force as you disassemble and assemble the cover panel . Please follow the following instructions .
Removing the screws
Cover panel is assembled on the bottom part of the indoor unit (as shown in the illustration) and it is fastened with screws . Remove the Cap screw first and unfasten the screws so that you can disassemble the cover panel .
Cap Screw
<Remove the Cap screw>
Cover Panel
<Unfasten the screw>
�� A3050 CH&XL_IB&IM_DB68-04219A_HP&CO_EN.indd 37
English-37
2014/7/10 16:50:44
Disassembling/Assembling the Cover panel for indoor unit installation
Removing the Cover panel (Before mounting the indoor unit)
The bottom panel fits the main body using the side, center, and bottom hooks as shown . Unlock the side hooks first, and then unlock the center and bottom hooks .
Check the location of the hooks before removing the cover panel .
Location of the hooks on the central part
Number and location of the hooks
Side hooks
Center hook Bottom hook
Bottom hooks
Removing the hooks on the side
For specific Hook location and quantity, please refer to cover panel with indicating arrows based on physical goods .
Removing the hooks on the central part
② ①
Caution (fragile)
- Gently press the both side of the cover panel inwards (①) and release the hooks on both sides(②) .
Caution (fragile)
- Use both hands
- Release each hook by pushing it up at an angle .
Assembling the Cover panel (After mounting the indoor unit)
To assemble the Cover panel, proceed in reverse order of disassembling .
Use both hands for assembling and be extra careful not to damage the pipes and drain hose .
Lock the side, center, and bottom hooks in this sequence . Tighten the bottom panel with the screws, and close the screw holes with their cap .
<Lock the side hook> <Lock the bottom hook>
�� A3050 CH&XL_IB&IM_DB68-04219A_HP&CO_EN.indd 38
<Fasten the screw>
English-38
<Assemble the Cap screw>
2014/7/10 16:50:47
advertisement
Related manuals
advertisement
Table of contents
- 4 Safety precautions
- 10 Checking before use
- 12 Checking the name of the parts
- 13 Checking the remote controller
- 15 Basic function
- 17 Adjusting the air flow direction
- 18 Using the Fast function
- 18 Using the Comfort function
- 19 mode
- 20 Setting the On/Off timer
- 21 Using the Auto Clean function
- 22 Using the Single User function
- 22 Using the Virus Doctor function
- 23 Using the Quiet function
- 23 Using the Smart A/C application
- 23 Using the Filter reset
- 24 Cleaning the air conditioner
- 27 Maintaining the air conditioner
- 28 Troubleshooting
- 30 Safety precautions
- 31 Choosing the installation location
- 34 Accessories
- 36 Fixing the installation plate
- 37 Disassembling/Assembling the Cover panel for indoor unit installation
- 39 Connecting the assembly cable
- 41 Installing and connecting the assembly pipe of the indoor unit
- 42 Evacuating the indoor unit
- 42 Cutting or extending the pipe
- 44 Installing and connecting the drain hose of the indoor unit
- 45 Changing direction of the drain hose
- 46 Installing and connecting the drain hose of the outdoor unit
- 46 Evacuating the connected pipes
- 49 Performing the gas leak tests
- 50 Fixing the indoor unit in place
- 50 Fixing the outdoor unit in place
- 51 Smart Install mode
- 53 Final check and trial operation
- 53 Pump down procedure (when removing the product)
- 54 How to connect your extended power cables