- Home
- Domestic appliances
- Climate control
- Split-system air conditioners
- Samsung
- AR24HVSDKWK
- User manual
advertisement
Final check and trial operation
To complete the installation, perform the following checks and tests to ensure that the air conditioner operates correctly.
Check the followings:
• Strength of the installation site
• Tightness of pipe connection to detect gas leak
• Electric wiring connection
• Heat-resistant insulation of the pipe
• Drainage
• Grounding conductor connection
• Correct operation (follow the steps below)
1. Press the Power button and check the following:
The indicator on the indoor unit lights up.
The airflow blade opens and the fan gears up for operation.
2. Press the Mode button to select Cool or Heat
(ARHS) mode.
In Cool mode, use Temp hr. + or – button and set the temperature at 16 °C.
In Heat mode, use Temp hr. + or – button and set the temperature at 30 °C
(ARHS)
.
• Approximately 3~5 minutes later, outdoor unit will start to operate and the
Cool or Warm
(ARHS)
air will blow out.
• After 12 minutes of stationary condition check the indoor unit air treatment.
Cooling mode (indoor unit check) Inlet air temp. - Outlet air temp:
From 10 °C to 12 °C (indicative delta T)
Heating mode (indoor unit check)
(ARHS) Outlet air temp. - Inlet air temp:
From 11 °C to 14 °C (indicative delta T)
In heating mode, the indoor fan motor can remain off to avoid cold air blown into conditioned space
(ARHS)
.
3. Press the Air swing button and check the following:
The airflow blades work properly.
4. Press the Power button to stop the operation.
• When you complete the installation successfully, hand over this manual to the user for storage in a handy and safe place.
Pump down procedure (when removing the product)
1. Press the Power button on the indoor unit for 5 seconds. Beep will sound immediately to let you know that the product is ready for pump down procedure. Please let the compressor run for more than 5 minutes.
2 . Release the valve caps on High and Low pressure side.
3 . Use L wrench to close the valve on the high pressure side.
4 . After approximately 2 minutes, close the valve on the low pressure side.
5 . Stop operation of the air conditioner by pressing the power button on the indoor unit or remote controller.
6 . Disconnect the pipes.
English-53
�� A3050 CH&XL_IB&IM_DB68-04219A_HP&CO_EN.indd 53 2014/7/10 16:50:53
advertisement
Related manuals
advertisement
Table of contents
- 4 Safety precautions
- 10 Checking before use
- 12 Checking the name of the parts
- 13 Checking the remote controller
- 15 Basic function
- 17 Adjusting the air flow direction
- 18 Using the Fast function
- 18 Using the Comfort function
- 19 mode
- 20 Setting the On/Off timer
- 21 Using the Auto Clean function
- 22 Using the Single User function
- 22 Using the Virus Doctor function
- 23 Using the Quiet function
- 23 Using the Smart A/C application
- 23 Using the Filter reset
- 24 Cleaning the air conditioner
- 27 Maintaining the air conditioner
- 28 Troubleshooting
- 30 Safety precautions
- 31 Choosing the installation location
- 34 Accessories
- 36 Fixing the installation plate
- 37 Disassembling/Assembling the Cover panel for indoor unit installation
- 39 Connecting the assembly cable
- 41 Installing and connecting the assembly pipe of the indoor unit
- 42 Evacuating the indoor unit
- 42 Cutting or extending the pipe
- 44 Installing and connecting the drain hose of the indoor unit
- 45 Changing direction of the drain hose
- 46 Installing and connecting the drain hose of the outdoor unit
- 46 Evacuating the connected pipes
- 49 Performing the gas leak tests
- 50 Fixing the indoor unit in place
- 50 Fixing the outdoor unit in place
- 51 Smart Install mode
- 53 Final check and trial operation
- 53 Pump down procedure (when removing the product)
- 54 How to connect your extended power cables