advertisement
Preparation before Use
Network Setup (LAN Cable Connection)
The machine is equipped with network interface, which is compatible with network protocols such as TCP/IP
(IPv4), TCP/IP (IPv6), IPX/SPX, NetBEUI, IPSec, and AppleTalk. It enables network printing on the Windows,
Macintosh, UNIX, NetWare and other platforms.
This section explains the
TCP/IP (IPv4) Setup
and
AppleTalk Setup
procedures. For other network settings, refer to the
NOTE:
If user login administration is enabled, you can only change the settings by logging in with administrator privileges. If user login administration is disabled, the user authentication screen appears.
Enter a login user name and password, and press [Login]. The login user name and login password are both set to "2500" in the factory default state.
TCP/IP (IPv4) Setup (by Entering IP Addresses)
Set up TCP/IP (IPv4) to connect to the Windows network. Set the IP addresses, subnet masks, and gateway addresses. The default settings are "TCP/IP Protocol:
On
, DHCP:
On
, Bonjour:
Off
, Auto-IP:
On
".
NOTE:
Before configuring TCP/IP (IPv4) settings, ask your network administrator for permission to obtain an IP address.
Use the procedure below.
System - IPv4
Set TCP/IP (IPv4).
* The setting will be changed after restarting the device or network.
IP Address
Subnet Mask
On
Default
Gateway
0.0.0.0
0.0.0.0
0.0.0.0
Status
Off
DHCP
Off
Bonjour
Cancel
On
Auto-IP
OK
12/12/2011 10:10
1
Press the
System Menu
key.
2
Press [System], [Next] of
Network
and then [Next] of
TCP/IP Setting
.
3
Press [Change] of
TCP/IP
.
4
Press [On] and then press [OK].
5
Press [Change] of
IPv4
.
6
Press [DHCP].
7
Press [Off] of
DHCP
and then press [OK].
8
Press [Bonjour].
9
Press [Off] of
Bonjour
and then press [OK].
10
Press [IP Address] and enter the address using the numeric keys.
11
Press [Subnet Mask] and enter the address using the numeric keys.
12
Press [Default Gateway] and enter the address using the numeric keys.
2
2-13
Preparation before Use
13
Check if all the address entries are correct and press [OK].
14
After changing the setting, restart the network from the system menu, or turn the machine OFF and then ON.
For detailed information on restarting the network, refer to
DHCP Settings
Select whether or not to use the DHCP server. The default setting is
On
.
Use the procedure below.
1
Press the
System Menu
key.
2
Press [System], [Next] of
Network
and then [Next] of
TCP/IP Setting
.
3
Press [Change] of
TCP/IP
.
4
Press [On] and then press [OK].
5
Press [Change] of
IPv4
.
6
Press [DHCP].
7
Press [On] or [Off] of
DHCP
and then press [OK].
8
After changing the setting, restart the network from the system menu, or turn the machine OFF and then ON.
For detailed information on restarting the network, refer to
Bonjour Settings
Select whether or not to use Bonjour. The default setting is
Off
.
2-14
Preparation before Use
Auto-IP Settings
Select whether or not to use Auto-IP. The default setting is
On
.
Use the procedure below.
1
Press the
System Menu
key.
2
Press [System], [Next] of
Network
and then [Next] of
TCP/IP Setting
.
3
Press [Change] of
TCP/IP
.
4
Press [On] and then press [OK].
5
Press [Change] of
IPv4
.
6
Press [Auto-IP].
7
Press [On] or [Off] of Auto-IP and then press [OK].
8
After changing the setting, restart the network from the system menu, or turn the machine OFF and then ON.
For detailed information on restarting the network, refer to
2
AppleTalk Setup
Select the Apple Talk network connection. The default setting is
On
.
2-15
advertisement
Key Features
- 4-in-1 functionality: Copy, print, scan, and fax
- A3 paper size support
- High-speed printing and copying
- Exceptional print quality with 2,400 x 600 dpi resolution
- Automatic document feeder for hassle-free scanning
- Intuitive operation with a user-friendly control panel
- Network connectivity for easy sharing and printing
- Support for various paper types and sizes
- Energy-efficient operation with low power consumption
- Compact and space-saving design