advertisement
«
CAUTION
!
Because the pump adapter is in use, it is impossible to measure in these conditions!
If the status » Enable « is active, pumped mode is activated whenever the adapter for pumped mode is fitted.
7.2.18
Clr Exposition
This function is used to reset peak values, short-term values and shift-average values.
Select the menu items » Settings
OK
\ Instrument \ Clr Exposition
« key after each selection.
«
Confirm the deletion of the peak values, short-term values and shift-average values using the »
OK
« key.
7.2.19
Clear Min/Max
If the peak values need to be reset.
Select the menu items » Settings in this order, pressing the »
OK
\ Instrument \ Clear Min/Max
« key after each selection.
Confirm the deletion of the peak values using the »
OK
« key.
«
7.2.21
Display contrast
This function is used to adjust the contrast of the display.
Select the menu items » Settings in this order, pressing the »
OK
\ Instrument \ Display contrast
« key after each selection.
Use the »
The
« and »
M
« keys to adjust the contrast. adjustments are immediately visible on the display.
Adjustable range: 0 to 63
«
7.2.22
Restart System
Restart of the whole system. Warm-up of all sensors.
7.2.23
Language
This function is used to select the language for the instrument and all displays.
Select the menu items » Settings order, pressing the »
OK
\ Instrument \ Language
« key after each selection.
« in this
Select the desired language from the list and press the »
OK
« key to activate it.
i i
NOTICE
It is possible to switch to a language with some potentially incomprehensible characters. This will make further use of the menus very difficult or even impossible.
7.2.20
Key beep
This function is used to activate the key beep.
Select the menu items » Settings order, pressing the »
OK
\ Instrument \ Key beep
« key after each selection.
Select the desired status » Enable the »
OK
« key to activate it.
« or » Disable
« in this
« and press
If the status » Enable « is active, each press of a key on the instrument is confirmed with a short audible tone (beep).
64 Dräger X-am 7000
advertisement
Related manuals
advertisement
Table of contents
- 5 Zu Ihrer Sicherheit
- 5 Allgemeine Sicherheitshinweise
- 5 Bedeutung der Warnzeichen
- 6 Menüfunktionen
- 6 Menüstruktur
- 6 (Werkseinstellung)
- 7 Übersicht
- 7 Bedienungsgrundlagen
- 7 In den Menübetrieb wechseln
- 7 Kennwort eingeben
- 8 Navigation im Menü
- 8 Aktivierbare Funktionen
- 10 Übersicht
- 10 Hinweise anzeigen
- 10 Fehler anzeigen
- 10 Batterie Info
- 11 Versions Info
- 11 Letzte Kalibrierung
- 11 Nächste Kalibrierung
- 12 Kurzzeitwert
- 12 Schichtmittelwert
- 12 Maximaler Wert
- 12 Minimaler Wert
- 13 Übersicht
- 13 Frischluft-Kalibrierung
- 14 Mischgas-Kalibrierung
- 15 Mischgas-Kalibrierung konfigurieren
- 15 Begasungstest konfigurieren
- 15 Sensor kalibrieren/justieren
- 17 Übersicht
- 18 Lecksuche Modus
- 18 Tracking Modus
- 18 Datum und Zeit
- 18 Datumsformat / Zeitformat
- 19 Funktionstaste
- 19 Stiller Alarm
- 19 Betriebssignal
- 20 Grundinitialisierung Gerät
- 20 Mess-Stelle
- 20 Benutzer Kennziffer
- 20 Einstellung Quickmenü
- 20 Kennwort Info
- 21 Kennwort Kalibrierung
- 21 Kennwort Einstellung
- 21 Ausschalt-Sperre
- 21 Telemetrie
- 21 Pumpe
- 22 Lösche Expo
- 22 Lösche Min/Max
- 22 Tastenton
- 22 Anzeige-Kontrast
- 22 Restart System
- 22 Sprache
- 23 Übersicht
- 23 Aktiv-Status
- 23 Einstellung der Sensoren
- 23 Gaskonfiguration
- 25 Einstellbares Kalibrierintervall
- 25 Mittelwertdauer
- 26 Kurzzeitwert
- 26 Kurzzeitwertdauer
- 26 Gesamte Exposition
- 26 Aktiver Datensatz
- 27 Auswahl Datensatz
- 27 Grundinitialisierung Kanal
- 27 Übersicht
- 27 Konfiguration des Datenspeichers
- 28 – Datenspeicher An/Aus
- 28 – Spitzen/Mittel
- 28 – Speicherinterval
- 28 – Überschreiben
- 28 Lösche Expositionswerte
- 29 Schichtlänge
- 29 Expositions-Status
- 29 Applikations Mode
- 31 Störungen, Ursache und Abhilfe
- 36 Pflege
- 36 Instandhaltung
- 36 Instandhaltungsintervalle
- 37 Gerät kalibrieren / justieren
- 37 Justieren mit Prüfgas
- 38 Justieren mit Prüfgasampullen
- 38 Justieren für Lösemittel mit Kalibrierkammer
- 39 Begasungstest
- 39 Begasungstest starten
- 41 Sensoren wechseln
- 43 Pumpe wechseln
- 43 Sensor-Membrane in der Dichtplatte wechseln
- 44 Betrieb ohne Sensor-Membrane
- 44 Versorgungseinheit wechseln
- 44 Ersatz-NiMH-Versorgungseinheit
- 47 For your safety
- 47 General safety notes
- 47 Definitions of Alert Icons
- 48 Menu functions
- 48 Menu structure
- 48 « menu
- 48 Default passwords (factory setting)
- 49 Overview
- 49 Basic operating procedures
- 49 Switching to menu mode
- 49 Entering the password
- 50 Menu navigation
- 50 Functions which can be activated
- 52 Overview
- 52 Show Notice
- 52 Show Fault
- 52 Show Battery
- 53 Show Version
- 53 Last calibration
- 53 Next calibration date
- 54 Show STEV
- 54 Show TWA
- 54 Show maximum value
- 54 Show minimum value
- 55 Overview
- 55 Fresh air calibration
- 56 Mixed-gas calibration
- 57 Mixed-gas configuration
- 57 Bumptest configuration
- 57 Calibrating and adjusting sensors
- 59 Overview
- 60 Leakage mode
- 60 Tracking mode
- 60 Date and time
- 60 Date format / Time format
- 61 Function key
- 61 Silent Alarm
- 61 Life Signal
- 62 Initialise device
- 62 Session ID
- 62 Personal ID
- 62 Quick menu settings
- 62 Password Info
- 63 Password for calibration menu
- 63 Password for settings menu
- 63 Switch off lock
- 63 Telemetry
- 64 Clr Exposition
- 64 Clear Min/Max
- 64 Key beep
- 64 Display contrast
- 64 Restart System
- 64 Language
- 65 Overview
- 65 Sensor status
- 65 Sensor settings
- 65 Gas configuration
- 67 Adjustable calibration interval
- 67 Mean value period
- 68 Short time period
- 68 Total exposure
- 68 Active selection
- 69 Select status
- 69 Initialise channel
- 69 Overview
- 69 Configuration of the data logger
- 70 – Data logger on/off
- 70 – Peak/Average
- 70 – Sample time
- 70 – Roll
- 70 Clear exposure values
- 71 Shift Duration
- 71 Exposure status
- 71 Application mode
- 73 Fault – Cause – Remedy
- 78 Maintenance
- 78 Maintenance intervals
- 79 Calibrating and adjusting the instrument
- 79 Adjustment with test gas
- 80 Calibration with test-gas ampoules
- 80 Calibration for solvents with a calibration chamber
- 81 Bump test
- 81 Start bump test function
- 83 Replacing the Sensors
- 85 Changing pump
- 85 Replacing the sensor membrane on sealing plate
- 86 Operation without the sensor membrane
- 86 Changing the power pack
- 86 Replacement of the NiMH power pack