Chapter 2: Hardware Installation. Biostar J1800NP
Add to My manuals35 Pages
Biostar J1800NP is a mini-ITX form factor motherboard that supports IntelĀ® CeleronĀ® J1800 or J1900 processors (J1800NP model supports J1800) and up to 16GB of DDR3L memory. It features 2x SATA 3Gb/s connectors for storage, 6x USB 2.0 ports, 1x USB 3.0 port, 1x PCI x1 slot, and Realtek RTL 8111G 10/ 100/ 1000 Mb/s LAN. The rear panel includes VGA, HDMI, and COM ports, as well as 3x audio jacks. The motherboard also has 2x system fan connectors, 2x USB 2.0 headers, and 1x front panel header.
advertisement
J1800NHP/J1800NP/J1900NHP/J1900NP
CHAPTER 2: HARDWARE INSTALLATION
These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.
SYS_FAN1/2: System Fan Header
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM rate sense
Note: SYS_FAN1/2 support 4-pin and 3-pin head connectors. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.
A. DDR3L SO-DIMM Module (1.35V/1.5V)
Step 1: Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot.
5
Motherboard Manual
Step 2: Insert the DIMM firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.
Note1: The DIMM must be installed to DIMMA1 slot first.
Note2: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
B. Memory Capacity
DIMM Socket Location DDR3L Module
DIMMA1 512MB/1GB/2GB/4GB/8GB
DIMMB1 512MB/1GB/2GB/4GB/8GB
Total Memory Size
Max is 16GB
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DIMMA1 DIMMB1
Disabled O X
Enabled O O
(O means memory installed, X means memory not installed.)
Note: The DRAM bus width of the memory module must be the same (x8 or x16)
6
advertisement
Related manuals
advertisement
Table of contents
- 3 Chapter 1: Introduction
- 3 Before You Start
- 3 Package Checklist
- 4 Motherboard Specifications
- 5 Central Processing Unit (CPU)
- 5 Rear Panel Connectors
- 6 Motherboard Layout
- 7 Chapter 2: Hardware Installation
- 7 Connect Cooling Fans
- 7 Install System Memory
- 9 Expansion Slots
- 10 Jumper Setting
- 11 Headers & Connectors
- 15 Chapter 3: UEFI BIOS & Software
- 15 UEFI BIOS Setup
- 15 BIOS Update
- 19 Software
- 22 Chapter 4: Useful Help
- 24 Driver Installation
- 25 AMI BIOS Beep Code
- 25 Troubleshooting
- 27 Appendix: SPEC In Other Languages
- 27 Arabic
- 28 French
- 29 German
- 30 Italian
- 31 Japanese
- 32 Polish
- 33 Portuguese
- 34 Russian
- 35 Spanish