advertisement
WAGO-I/O-SYSTEM 750
750-316/300-000 Fieldbus Coupler MODBUS RTU
Mounting 61
5.5 Mounting Sequence
Fieldbus couplers/controllers and I/O modules of the WAGO-I/O-SYSTEM 750 are snapped directly on a carrier rail in accordance with the European standard EN
50022 (DIN 35).
The reliable positioning and connection is made using a tongue and groove system. Due to the automatic locking, the individual devices are securely seated on the rail after installation.
Starting with the fieldbus coupler/controller, the I/O modules are mounted adjacent to each other according to the project design. Errors in the design of the node in terms of the potential groups (connection via the power contacts) are recognized, as the I/O modules with power contacts (blade contacts) cannot be linked to I/O modules with fewer power contacts.
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent injury.
Insert I/O modules only from the proper direction!
All I/O modules feature grooves for power jumper contacts on the right side. For some I/O modules, the grooves are closed on the top. Therefore, I/O modules featuring a power jumper contact on the left side cannot be snapped from the top.
This mechanical coding helps to avoid configuration errors, which may destroy the I/O modules. Therefore, insert I/O modules only from the right and from the top.
Don't forget the bus end module!
Always plug a bus end module 750-600 onto the end of the fieldbus node! You must always use a bus end module at all fieldbus nodes with WAGO-I/O-
SYSTEM 750 fieldbus couplers/controllers to guarantee proper data transfer.
Manual
Version 1.0.0
advertisement
Related manuals
advertisement
Table of contents
- 6 Notes about this Documentation
- 6 Validity of this Documentation
- 6 Copyright
- 7 Symbols
- 9 Number Notation
- 9 Font Conventions
- 10 Important Notes
- 10 Legal Bases
- 10 Subject to Changes
- 10 Personnel Qualifications
- 10 Provisions
- 11 Technical Condition of Specified Devices
- 12 Safety Advice (Precautions)
- 14 System Description
- 15 Manufacturing Number
- 16 Component Update
- 16 Storage, Assembly and Transport
- 17 Assembly Guidelines/Standards
- 18 Power Supply
- 18 Isolation
- 19 System Supply
- 19 Connection
- 20 Dimensioning
- 23 Field Supply
- 23 Connection
- 25 Fusing
- 28 Supplementary Power Supply Regulations
- 29 Supply Example
- 31 Power Supply Unit
- 32 Grounding
- 32 Grounding the DIN Rail
- 32 Framework Assembly
- 32 Insulated Assembly
- 33 Grounding Function
- 34 Shielding
- 34 General
- 34 Bus Cables
- 35 Signal Lines
- 35 WAGO Shield Connecting System
- 36 Device Description
- 39 Connectors
- 39 Device Supply
- 40 Fieldbus Connection
- 41 Display Elements
- 42 Operating Elements
- 42 Service Interface
- 43 Mode Selector Switch
- 49 Manual Configuration
- 52 Technical Data
- 52 Device Data
- 52 System Data
- 52 Connection Type
- 53 Climatic Environmental Conditions
- 53 Mechanical Strength acc. to IEC
- 54 Approvals
- 56 Standards and Guidelines
- 57 Mounting
- 57 Installation Position
- 57 Overall Configuration
- 59 Mounting onto Carrier Rail
- 59 Carrier Rail Properties
- 60 WAGO DIN Rail
- 60 Spacing
- 61 Mounting Sequence
- 62 Inserting and Removing Devices
- 63 Inserting the Fieldbus Coupler/Controller
- 63 Removing the Fieldbus Coupler/Controller
- 64 Inserting the I/O Module
- 65 Removing the I/O Module
- 66 Connect Devices
- 66 Data Contacts/Internal Bus
- 67 Power Contacts/Field Supply
- 69 Function Description
- 69 Startup of the Fieldbus Coupler
- 71 Process Data Architecture
- 71 Basic Setup
- 72 Example of an Input Process Image
- 73 Example of an Output Process Image
- 74 Process Data MODBUS RTU
- 75 Data Exchange
- 75 Memory Space
- 76 Addressing
- 76 Adressing the I/O Modules
- 79 Commissioning
- 80 Diagnostics
- 80 LED Signaling
- 81 Evaluating Fieldbus Status
- 82 Evaluating Node Status – I/O LED (Blink Code Table)
- 163 Figure 1: Fieldbus Node (Example)
- 164 Figure 2: Labeling on the Side of a Component (Example)
- 164 Figure 3: Example of a Manufacturing Number
- 167 Figure 4: Isolation for Fieldbus Couplers/Controllers (Example)
- 168 System Supply Module (right)
- 169 Couplers
- 174 Figure 8: Supply Module with Fuse Carrier (Example 750-610)