advertisement
▼
Scroll to page 2
of
74
ST2516 Series Operation Manual connected. If not, the deducted data will be wrong, and further it will cause result errors. The correct connection is shown as the following figure.
3.2
<COMP DISP>
Touch <MEAS DISP> or press [MEAS] to select the COMP DISP soft key to enter into the <COMP
DISP> page shown as figure 3-2.
<COMP DISP>
COMP
OFF
COMP MODE
ABS
FILE
HIGH
225.000
R: 499.76
COMP: HI
Ω
TOT:0
HI :0
IN :0
LO :0
TOOLS
LOW
63.0000
MEAS
DISP
COMP
DISP
BIN
DISP
STATICS
DISP
MORE 1/2
11:36:54
Figure 3-2
The following parameters can be set on this page:
FILE
TOOLS
COMP ON/OFF
COMP MODE
NOM (nominal value)
Low limit (%)
12
advertisement
Related manuals
Download
PDF
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 9 Warm-up
- 9 Other Features
- 10 Introduction to Front and Rear Panels
- 10 Introduction to Front Panel
- 11 Introduction to Rear Panel
- 12 Display Zone
- 13 Introduction to Buttons on Front Panel
- 13 [MEAS]
- 13 [SYSTEM]
- 14 Simple Operation
- 14 Starting Up
- 15 Basic Operation
-
15
- 15 Measurement Functions
- 16 Measurement Range
- 17 Measurement Speed
- 17 File Manage
- 17 Tools
-
18
- 19 File Manage
- 19 Tools
- 19 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
20
- 21 STATIS DISP
- 22 Edge Mode and Settings of Its Relevant Values
- 22 Status ON/OFF
- 22 Parameters of Statistic Analysis
- 23 TOOLS
-
24
- 25 ST2516)
- 25 Temperature Correction (TC)
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 30 System Setup and File Manage
- 30 System Setup
- 30 TouchTone
- 30 Language
- 31 Password
- 31 Bus Mode
- 32 Baud Rate
- 32 AC Freq
- 32 Handler VCC
- 32 LCD Style
- 32 Setting Time and Date
-
33
- 33 Introduction to Save/Recall
- 33 Structure of File Folder/File in a U Disk
- 37 Performance Index
- 37 Measurement Function
- 37 Measurement Parameters and Notations
- 37 Measurement Groups
- 37 Range
- 37 Trigger
- 37 Mode of Test Terminal
- 38 Resistance Measurement Time
- 38 Average
- 38 Test Signal
- 38 Current range
- 38 Output Voltage of Open Circuit
- 38 Maximum Display Range
- 39 Measurement Accuracy
- 39 Basic Accuracy for Resistance Measurement
- 40 Accuracy for Resistance Tested at Low Current Mode
- 40 Accuracy for Temperature Measurement (Pt500)
- 40 Accuracy for Temperature Measurement (Analog Input)
- 41 Remote Control
- 41 RS232C Connection
- 42 USBTMC Remote Control System
- 42 System Configuration
- 42 Install the Driver
- 43 USBCDC Virtual Serial Port
- 43 System Configuration
- 43 Installing Driver
- 44 SCIP Command Reference
- 44 ST2516 Subsystem Commands
- 44 DISPlay Subsystem Commands
- 45 FUNCtion Subsystem Commands
- 49 APERture Subsystem Commands
- 49 TRIGger Subsystem Commands
- 51 FETCH? Subsystem Commands
- 52 TEMPerature Subsystem Commands(ST2516)
- 55 COMParator Subsystem Commands
- 58 BIN Subsystem Commands
- 62 STATistics Subsystem Commands
- 67 SYSTem Subsystem Commands
- 70 Handler Interface
- 72 Package Contents and Warranty
- 72 Package Contents
- 72 Marks
- 72 Package
- 73 Shipping
- 73 Storage
- 73 Warranty