advertisement
ST2516 Series Operation Manual
9.4
Shipping
In the shipment, the instrument should be handled with care and some precautions must be taken to resist moisture and water.
9.5
Storage
The instrument should be stored in an airy room where the environment temperature ranges from 5 ℃ to 40 ℃ , relative humidity is not greater than 85% and the air contains no detrimental impurities that might corrode the instrument.
9.6
Warranty
This instrument is warranted against defects in material and workmanship for a period of one years from the date of shipment. You should supply us with the warranty card before you enjoy the free maintenance service. This warranty does not apply in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs. We will, without charge, repair or replace, at its option, defective product or component parts.
The maintenance for this instrument should be performed by professional maintenance personnel. Do not substitute the internal components unauthorized when maintaining. In order to ensure the measurement accuracy, the instrument must be measured and corrected after maintenance. You should bear the maintenance expense for damages caused by unauthorized repairing or substituting components.
67
www.sourcetronic.com
SOURCETRONIC GMBH
Fahrenheitstrasse 1
28359 Bremen
Germany
T +49 421 2 77 99 99
F +49 421 2 77 99 98 [email protected]
www.sourcetronic.com
skype: sourcetronic
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 9 Warm-up
- 9 Other Features
- 10 Introduction to Front and Rear Panels
- 10 Introduction to Front Panel
- 11 Introduction to Rear Panel
- 12 Display Zone
- 13 Introduction to Buttons on Front Panel
- 13 [MEAS]
- 13 [SYSTEM]
- 14 Simple Operation
- 14 Starting Up
- 15 Basic Operation
-
15
- 15 Measurement Functions
- 16 Measurement Range
- 17 Measurement Speed
- 17 File Manage
- 17 Tools
-
18
- 19 File Manage
- 19 Tools
- 19 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
20
- 21 STATIS DISP
- 22 Edge Mode and Settings of Its Relevant Values
- 22 Status ON/OFF
- 22 Parameters of Statistic Analysis
- 23 TOOLS
-
24
- 25 ST2516)
- 25 Temperature Correction (TC)
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 30 System Setup and File Manage
- 30 System Setup
- 30 TouchTone
- 30 Language
- 31 Password
- 31 Bus Mode
- 32 Baud Rate
- 32 AC Freq
- 32 Handler VCC
- 32 LCD Style
- 32 Setting Time and Date
-
33
- 33 Introduction to Save/Recall
- 33 Structure of File Folder/File in a U Disk
- 37 Performance Index
- 37 Measurement Function
- 37 Measurement Parameters and Notations
- 37 Measurement Groups
- 37 Range
- 37 Trigger
- 37 Mode of Test Terminal
- 38 Resistance Measurement Time
- 38 Average
- 38 Test Signal
- 38 Current range
- 38 Output Voltage of Open Circuit
- 38 Maximum Display Range
- 39 Measurement Accuracy
- 39 Basic Accuracy for Resistance Measurement
- 40 Accuracy for Resistance Tested at Low Current Mode
- 40 Accuracy for Temperature Measurement (Pt500)
- 40 Accuracy for Temperature Measurement (Analog Input)
- 41 Remote Control
- 41 RS232C Connection
- 42 USBTMC Remote Control System
- 42 System Configuration
- 42 Install the Driver
- 43 USBCDC Virtual Serial Port
- 43 System Configuration
- 43 Installing Driver
- 44 SCIP Command Reference
- 44 ST2516 Subsystem Commands
- 44 DISPlay Subsystem Commands
- 45 FUNCtion Subsystem Commands
- 49 APERture Subsystem Commands
- 49 TRIGger Subsystem Commands
- 51 FETCH? Subsystem Commands
- 52 TEMPerature Subsystem Commands(ST2516)
- 55 COMParator Subsystem Commands
- 58 BIN Subsystem Commands
- 62 STATistics Subsystem Commands
- 67 SYSTem Subsystem Commands
- 70 Handler Interface
- 72 Package Contents and Warranty
- 72 Package Contents
- 72 Marks
- 72 Package
- 73 Shipping
- 73 Storage
- 73 Warranty