advertisement
ST2516 Series Operation Manual
Anti-corrosion alloy Nickel: 2.5 to 4.0
Silicon: 0.5 to 1.0
Soft aluminum
Hard-drawn
Aluminum>99.5
Aluminum>99.5 aluminum
Aluminum alloy Silicon: 0.4 to 0.6
Magnesium: 0.4 to
0.5
Aluminum: 99.2 to
98.9
---
2.7
2.7
---
0.25 to 0.45
0.63 to 0.64
0.60 to 0.62
0.50 to 0.55
980 to 1770
42
40
36
NOTE: Calculating the conductivity and the temperature coefficient of the copper wire:
Diameter [mm]
0.01 to 0.26
0.26 to 0.50
0.50 to 2.00
2.00 to 8.00
(Conductivity)
0.98
0.993
1.00
1.00 copper (conductivity)
0.93
0.94
0.96
0.97
Hard-drawn copper
(Conductivity)
---
0.96
0.96
0.97
(
Temperature coefficient ( α t
) varies with environment temperature and material conductivity. It is supposed that the temperature coefficient of a material at 20 , its temperature coefficient
α
α ct ct
) at t
=
1
α 20
1 x c
+ ( t−20 )
℃ will be as the following expression:
3.6.3
Types of Temperature Sensor
There are two temperature input types: Pt and Analog Input.
PT500
Touch the T.SENS
soft key to select the temperature input type. Select PT and the input type of the temperature is platinum resistor temperature sensor. At this time, standard configuration of
“PT500 temperature sensor” should be inserted in the temperature measurement input terminal.
Analog Input
Touch the T.SENS
soft key to select the temperature input type. AnLG_In is analog input(the input voltage is 0-2V) and the corresponding forma is :
T2−T1
V2−V1
*(Input Voltage) +
T1V2 – T2V1
V2−V1
-----------------------------------------------------------------------------------------------------------------------------
21
advertisement
Related manuals
advertisement
Table of contents
- 7 Introduction to Instrument, Unpacking and Installing
- 7 Introduction to Instrument
- 7 Unpacking
- 7 Power Connection
- 8 Environment
- 8 Use of Test Fixture
- 9 Warm-up
- 9 Other Features
- 10 Introduction to Front and Rear Panels
- 10 Introduction to Front Panel
- 11 Introduction to Rear Panel
- 12 Display Zone
- 13 Introduction to Buttons on Front Panel
- 13 [MEAS]
- 13 [SYSTEM]
- 14 Simple Operation
- 14 Starting Up
- 15 Basic Operation
-
15
- 15 Measurement Functions
- 16 Measurement Range
- 17 Measurement Speed
- 17 File Manage
- 17 Tools
-
18
- 19 File Manage
- 19 Tools
- 19 COMP (ON/OFF)
- 19 Compare Mode and SETTINGS of ABS & Percent Error
-
20
- 21 STATIS DISP
- 22 Edge Mode and Settings of Its Relevant Values
- 22 Status ON/OFF
- 22 Parameters of Statistic Analysis
- 23 TOOLS
-
24
- 25 ST2516)
- 25 Temperature Correction (TC)
- 27 Types of Temperature Sensor
- 28 Parameter Setting
-
28
- 30 System Setup and File Manage
- 30 System Setup
- 30 TouchTone
- 30 Language
- 31 Password
- 31 Bus Mode
- 32 Baud Rate
- 32 AC Freq
- 32 Handler VCC
- 32 LCD Style
- 32 Setting Time and Date
-
33
- 33 Introduction to Save/Recall
- 33 Structure of File Folder/File in a U Disk
- 37 Performance Index
- 37 Measurement Function
- 37 Measurement Parameters and Notations
- 37 Measurement Groups
- 37 Range
- 37 Trigger
- 37 Mode of Test Terminal
- 38 Resistance Measurement Time
- 38 Average
- 38 Test Signal
- 38 Current range
- 38 Output Voltage of Open Circuit
- 38 Maximum Display Range
- 39 Measurement Accuracy
- 39 Basic Accuracy for Resistance Measurement
- 40 Accuracy for Resistance Tested at Low Current Mode
- 40 Accuracy for Temperature Measurement (Pt500)
- 40 Accuracy for Temperature Measurement (Analog Input)
- 41 Remote Control
- 41 RS232C Connection
- 42 USBTMC Remote Control System
- 42 System Configuration
- 42 Install the Driver
- 43 USBCDC Virtual Serial Port
- 43 System Configuration
- 43 Installing Driver
- 44 SCIP Command Reference
- 44 ST2516 Subsystem Commands
- 44 DISPlay Subsystem Commands
- 45 FUNCtion Subsystem Commands
- 49 APERture Subsystem Commands
- 49 TRIGger Subsystem Commands
- 51 FETCH? Subsystem Commands
- 52 TEMPerature Subsystem Commands(ST2516)
- 55 COMParator Subsystem Commands
- 58 BIN Subsystem Commands
- 62 STATistics Subsystem Commands
- 67 SYSTem Subsystem Commands
- 70 Handler Interface
- 72 Package Contents and Warranty
- 72 Package Contents
- 72 Marks
- 72 Package
- 73 Shipping
- 73 Storage
- 73 Warranty