advertisement
Where to Go From Here
Change LED Appearance
If you want to change the appearance of the LEDS, follow these steps:
1.
From the controller, click Configuration > Devices > AP, and then select the AP.
2.
Select one of these settings for the LED Mode setting:
—
—
—
Normal: LEDs are as described below
Node ID: Not supported in release 4.1
Blink: Sets all LEDs flashing; this is useful to locate an AP
—
Dark: Turns off all LEDs
3.
Click OK.
Where to Go From Here
Now that the AP320i is installed, go to the Meru System Director Getting Started Guide for instructions on initializing the hardware. Return to this chapter to check the status of the LEDs once the WLAN is operational.
© 2012 Meru Networks, Inc.
Installing AP320i 53
Where to Go From Here
54 Meru Access Point Installation Guide © 2012 Meru Networks, Inc.
advertisement
Related manuals
advertisement
Table of contents
- 15 Access Points
- 17 AP320i
- 18 AP332e
- 18 AP332i
- 21 Installing AP
- 21 Safety Precautions
- 22 Best Practices for an AP300/AP1000 Network
- 23 Unpack the AP
- 24 Determine Power Requirements
- 24 802.af PoE Usage
- 24 802.3at PoE Usage
- 25 Installation Requirements
- 26 Additional Equipment
- 26 Install the AP
- 26 Select a Location
- 27 Attach the Provided Antennas
- 30 Install the Remote Antenna Mount (optional)
- 35 Install Antennas With One Connector (optional)
- 37 Install the Access Point
- 43 Check AP300 LED Activity
- 45 Where to Go From Here
- 47 Installing AP320i
- 47 Safety Precautions
- 48 Best Practices for an AP320i/AP1000 Network
- 49 Unpack the AP320i
- 49 Determine Power Requirements
- 49 802.af PoE Usage
- 50 802.3at Usage
- 50 Additional Equipment
- 51 Installing AP320i
- 51 Select a Location
- 52 Install the Access Point
- 65 Check AP320i LED Activity
- 67 Where to Go From Here
- 69 Installing AP332e
- 69 Safety Precautions
- 69 Unpack the AP332e
- 70 Installation Requirements
- 70 Additional Equipment
- 71 Install the AP332e
- 71 Select a Location
- 72 Attach the Provided Antennas
- 72 Install the Access Point
- 80 Check AP332e LED Activity
- 82 Where to Go From Here
- 83 Installing AP332i
- 83 Safety Precautions
- 83 Unpack the AP332i
- 84 Additional Equipment
- 84 Installing AP332i
- 84 Select a Location
- 85 Install the Access Point
- 92 Check AP332i LED Activity
- 94 Where to Go From Here
- 95 Cautions and Warnings
- 95 Cautions
- 97 Warnings
- 101 Regulatory Information
- 101 For AP300/320i
- 101 Radio
- 101 Safety
- 102 Underwriters Laboratories
- 103 FCC Radiation Exposure Statement
- 103 Radio Frequency Interference Requirements
- 104 Canada. Industry Canada (IC)
- 106 Europe—EU Declaration of Conformity and Restrictions
- 109 IEEE 802.11a Restrictions
- 109 EEE 802.11b/g Restrictions
- 109 Japan
- 110 Singapore
- 110 Manufacturing Information
- 110 AP300 Plenum Requirements
- 111 Supported PoEs
- 111 Supported Power Over Ethernet Devices for Meru APs
- 113 Optional External Antennas
- 113 ACC-ANT-ABGN
- 114 ACC-ANT-O6ABGN-0606-O
- 115 ACC-ANT-O6ABGN-0607-PT
- 116 ACC-ANT-O1BG-1300-PN
- 118 ACC-ANT-6ABGN