LAN Emulation (LAN Interface only). TallyGenicom T6218LJ, T6212LJ, T6212, T6200 Series, T6215N
Add to My manuals92 Pages
advertisement
![LAN Emulation (LAN Interface only). TallyGenicom T6218LJ, T6212LJ, T6212, T6200 Series, T6215N | Manualzz LAN Emulation (LAN Interface only). TallyGenicom T6218LJ, T6212LJ, T6212, T6200 Series, T6215N | Manualzz](http://s2.manualzz.com/store/data/063412866_1-7d83cab9051b5730cad71c5b113b6aca-360x466.png)
Chapter 3: Printer Menus and Configuring Your Printer
LAN Emulation (LAN Interface only)
Used to select the emulation attached to the Ethernet port when using the
LANPlex interface. The possible selection are the same as the Ser/Par Emul option.
Twinax Emul (Twinax/Coax only)
Used to select the Twinax emulation when using the FourPlex interface. The possible settings are IBM 4234, IBM 4210, and IBM 5225. The default is IBM
4234. The Coax emulation will always be IBM 4234.
Dump Mode
Dump Mode is used to troubleshoot problems that may arise when processing data. It places the printer into a Hex Dump Mode. You can select three styles of printouts for use as debugging tools. The standard selections are:
OFF: Dump Mode is disabled. (Default selection)
Style1: Two column output. Text, spaces, and control codes are printed in hexadecimal code format in one column and ASCII equivalents in another column.
Style2: Only control codes are printed in hexadecimal format. ASCII characters are printed as is and escape sequences force a new line.
Style3: Control codes and spaces are printed in hexadecimal format. ASCII characters are printed as is and escape sequences force a new line.
Twinax Interface
There is only one style for Twinax. It is similar to the Serial/Parallel Style 1, except the Hex codes are EBCDIC instead of ACSII.
Coax Interface
There is only one style for Coax. It is a unique dump mode that prints the contents of the PCIA buffer associated with each data buffer.
IPDS Option
If the IPDS option is installed, the dump from the IPDS data stream will be uniquely formatted regardless of the Dump Mode selection.
IO Hold Time
This parameter allows you to set the amount of time the printer remains locked onto the I/O on which it is receiving data after data transmission stops. You can set this to be 5—600 seconds (Default selection = 30 seconds)
3–17
advertisement
Related manuals
advertisement
Table of contents
- 13 Chapter
- 13 Site Preparation
- 14 Unpacking your printer
- 14 Repacking
- 14 Reversible Doors
- 14 Figure 1-1. Reversible Doors
- 14 Removing the Shipping Hardware
- 15 Figure 1–2. Shipping Screw Locations
- 15 Setting Up Paper Stacking Chains
- 15 Figure 1-3. Paper Stacking Chains
- 16 Interface Connections and Powering Up
- 16 Interface Connectors
- 16 Maximum Interface Cable Length
- 16 Serial/Parallel only
- 16 Twinax
- 16 View)
- 17 Connecting the I/O
- 17 Serial/Parallel
- 17 Twinax Connector
- 17 Figure 1-5. Connecting the Host Connector Smart T
- 18 Coax Connector
- 18 Figure 1-6. Connecting with the BNC adapter
- 19 Powering Up
- 19 Figure 1–7. Printer (Rear View)
- 20 Paper System
- 20 Paper System Components
- 20 Figure 1–8. Paper System Components
- 37 Chapter
- 37 Introduction
- 37 Control Panel Menus
- 37 Figure 3-1 Control Panel Navigation
- 38 Categories, Parameters and Selections
- 38 Using Menus
- 40 How to Print a Control Panel Selections Report
- 41 Operator Menu
- 41 Font Category
- 41 Ser/Par Language
- 41 Tx/Cx Language (displays on Twinax/Coax printers only)
- 42 IPDS Language (displays only if IPDS is installed)
- 42 Ser/Par Character Set
- 43 Matrix
- 43 OCRA Density
- 43 Ser/Par Style
- 44 Tx/Cx Style
- 44 IPDS Style
- 44 Panel Language
- 44 OCR Standards
- 44 Slashed Zero
- 44 Compressed
- 45 Forms Category
- 45 Length (lines)
- 45 Length (inches)
- 45 Top Margin
- 45 Bottom Margin
- 45 Left Margin
- 46 Right Margin
- 46 Horz Adjust
- 46 Vert Adjust
- 46 Print to End Of Form (EOF)
- 47 Quick Access
- 47 Eject Distance
- 48 Impact
- 48 Paper Weight
- 49 Fast Slew
- 49 Double Strike
- 49 Quality (T6218 only)
- 49 RibbonMonitor
- 49 RibnMon Thresh
- 50 Ribbon Monitor Operation
- 51 Vertical Format Units (VFU) Category
- 51 VFU Enabled
- 51 Vertical Tab (VT) Channel
- 51 Skip When
- 52 Configuration Menu
- 52 Printer Category
- 52 Powerup
- 52 Ser/Par Emul
- 53 LAN Emulation (LAN Interface only)
- 53 Twinax Emul (Twinax/Coax only)
- 53 Dump Mode
- 53 Twinax Interface
- 53 Coax Interface
- 53 IPDS Option
- 53 IO Hold Time
- 54 Report
- 54 Current Config
- 54 All Configs
- 54 Configs
- 54 Calibrations
- 54 Ribbon Count
- 54 Last Fault
- 54 Fault Log
- 54 Version
- 54 Intellifilter
- 54 Beeper Mode
- 55 Codes Category
- 55 Auto LF (Line Feed)
- 55 Auto CR (Carriage Return)
- 55 Line Wrap
- 55 Wrap Line Feed
- 56 Print on CR
- 56 Form Feed at TOF
- 56 Alt ESC (Alternate Escape)
- 56 Upper Only
- 57 Code 7F
- 57 Print 80 to 9F Hex
- 57 Ignore Char
- 57 Sub Char From
- 57 Sub Char To
- 57 PTX SFCC
- 57 PTX ALS
- 58 TOF Control
- 58 DC3 Operation
- 58 SISO OverszBar
- 58 Barcod Top Pos
- 58 Oversz Top Pos
- 59 Graphics Category
- 59 Code V Command Character (CVCC)
- 59 Smooth Size
- 59 PY Then
- 59 PN Then
- 59 Dark Bar
- 60 Table 3–1. Bar Code Dot Density
- 60 Modplot
- 60 Figure 3–2. Modplot Example
- 60 Version
- 60 Descender
- 61 Vertical Scale
- 61 Special Function Command Character (SFCC)
- 61 Code V Language
- 61 Free Format
- 62 Automatic PY
- 62 MTPL Bar
- 62 Secured
- 62 IGP Terminator
- 62 BlkMax H
- 62 BlkMax V
- 62 BlkMin H
- 62 BlkMin V
- 62 Postnet Density
- 62 PGL Terminator
- 63 Ignore Term
- 63 Configurations Category
- 63 How to Save Configurations
- 64 Powerup Config
- 64 Config n Label - (where n = 1 to 10)
- 64 How to label a configuration slot
- 65 Serial I/O Category
- 65 Data Bits
- 65 Stop Bits
- 65 Parity
- 65 8th Bit
- 65 Protocol
- 66 Status Enquiry
- 67 DTR Function
- 67 DTR Polarity
- 67 Busy Polarity
- 67 RTS Function
- 67 Robust Xon
- 68 Parallel I/O Category
- 68 POPC (Print On Paper Command)
- 68 8th Bit
- 68 Bi-Directional
- 69 Intellifilter Category
- 69 Serial
- 69 Parallel
- 69 Twinax/Coax
- 70 Twinax/Coax Category
- 70 Send PA (Coax Only)
- 70 Address (Twinax Only)
- 70 SPD (Coax Only)
- 70 SCD (Twinax Only)
- 71 Host (Font) Style (Twinax Only)
- 71 Screen Size (Screen) (Coax Only)
- 71 Case (Coax Only)
- 71 Compatibility Switches (Coax Only)
- 72 IR Delay (Coax Only)
- 72 Hex Passthrough
- 73 GrAVM (Graphics AVM)
- 74 IPDS Category (IPDS Only)
- 74 Address (Twinax Only)
- 74 Density
- 74 Dark Bar
- 74 Smooth Size
- 74 Host Override
- 75 TCP/IP Menu - LAN Interface Only
- 75 IP Address
- 75 Gateway
- 75 Subnet
- 76 Test Menu
- 76 Pattern Category
- 76 Print
- 76 Fault Override Category
- 76 Paper Motion
- 77 Diag Category
- 77 Cal-Paper (Calibrate Paper Out)
- 77 Help Menu