advertisement
Chapter 3: Printer Menus and Configuring Your Printer
Code 7F
This parameter allows you to dictate how the printer will react when it receives a Hexadecimal code 7F. The default value depends on the emulation. (See the Emulation Parameter, presented earlier in this chapter.)
Ignore: The code is ignored.
Delete Char: The previous character is deleted.
Delete Buffer: The previous characters on the current print line are
Space:
Fill: deleted.
A Space character is substituted.
A Fill character is substituted.
Print 80 to 9F Hex
This parameter defines whether locations 80 through 9F Hex are to be treated as control characters or printable characters. The function of the control characters in this area depends on the emulation. The selections are ON
(printable characters) or OFF (control characters). The default value is ON.
Ignore Char
This parameter allows you to select a character that will be ignored in the incoming data stream. This parameter functions in all emulations and nondownloadable print modes. It does not function in plot mode, font download, or VFU download. Selections are 0-255, referring to the decimal value of any
8-bit character, or OFF. Default is OFF.
Sub Char From
This parameter allows you to select a character that will be replaced by the character designated by the Sub Char To parameter. This parameter functions in all emulations and non-downloadable print modes. It does not function in plot mode, font download, or VFU download. Default is OFF.
Sub Char To
This parameter allows you to select the character that will replace the character designated by the Sub Char From Parameter. This parameter functions in all emulations and non-downloadable print modes. It does not function in plot mode, font download, or VFU download. Default is OFF.
PTX SFCC
Defines the Special Function Control Character used by the Printronix P5000 emulation. The decimal value of the ASCII character code is entered. The default value is 1 (SOH).
PTX ALS
Defines the single line Alternate Line Spacing used by the ACK (Hex 06) command in the Printronix P5000 emulation. The possible selections are 8 or 10.3
which define the line density. The default value is 8.
The PTX SFCC and PTX ALS options will only appear if the Printronix
P5000 emulation is selected with the Ser/Par Emul control panel option.
3–21
advertisement
Related manuals
advertisement
Table of contents
- 13 Chapter
- 13 Site Preparation
- 14 Unpacking your printer
- 14 Repacking
- 14 Reversible Doors
- 14 Figure 1-1. Reversible Doors
- 14 Removing the Shipping Hardware
- 15 Figure 1–2. Shipping Screw Locations
- 15 Setting Up Paper Stacking Chains
- 15 Figure 1-3. Paper Stacking Chains
- 16 Interface Connections and Powering Up
- 16 Interface Connectors
- 16 Maximum Interface Cable Length
- 16 Serial/Parallel only
- 16 Twinax
- 16 View)
- 17 Connecting the I/O
- 17 Serial/Parallel
- 17 Twinax Connector
- 17 Figure 1-5. Connecting the Host Connector Smart T
- 18 Coax Connector
- 18 Figure 1-6. Connecting with the BNC adapter
- 19 Powering Up
- 19 Figure 1–7. Printer (Rear View)
- 20 Paper System
- 20 Paper System Components
- 20 Figure 1–8. Paper System Components
- 37 Chapter
- 37 Introduction
- 37 Control Panel Menus
- 37 Figure 3-1 Control Panel Navigation
- 38 Categories, Parameters and Selections
- 38 Using Menus
- 40 How to Print a Control Panel Selections Report
- 41 Operator Menu
- 41 Font Category
- 41 Ser/Par Language
- 41 Tx/Cx Language (displays on Twinax/Coax printers only)
- 42 IPDS Language (displays only if IPDS is installed)
- 42 Ser/Par Character Set
- 43 Matrix
- 43 OCRA Density
- 43 Ser/Par Style
- 44 Tx/Cx Style
- 44 IPDS Style
- 44 Panel Language
- 44 OCR Standards
- 44 Slashed Zero
- 44 Compressed
- 45 Forms Category
- 45 Length (lines)
- 45 Length (inches)
- 45 Top Margin
- 45 Bottom Margin
- 45 Left Margin
- 46 Right Margin
- 46 Horz Adjust
- 46 Vert Adjust
- 46 Print to End Of Form (EOF)
- 47 Quick Access
- 47 Eject Distance
- 48 Impact
- 48 Paper Weight
- 49 Fast Slew
- 49 Double Strike
- 49 Quality (T6218 only)
- 49 RibbonMonitor
- 49 RibnMon Thresh
- 50 Ribbon Monitor Operation
- 51 Vertical Format Units (VFU) Category
- 51 VFU Enabled
- 51 Vertical Tab (VT) Channel
- 51 Skip When
- 52 Configuration Menu
- 52 Printer Category
- 52 Powerup
- 52 Ser/Par Emul
- 53 LAN Emulation (LAN Interface only)
- 53 Twinax Emul (Twinax/Coax only)
- 53 Dump Mode
- 53 Twinax Interface
- 53 Coax Interface
- 53 IPDS Option
- 53 IO Hold Time
- 54 Report
- 54 Current Config
- 54 All Configs
- 54 Configs
- 54 Calibrations
- 54 Ribbon Count
- 54 Last Fault
- 54 Fault Log
- 54 Version
- 54 Intellifilter
- 54 Beeper Mode
- 55 Codes Category
- 55 Auto LF (Line Feed)
- 55 Auto CR (Carriage Return)
- 55 Line Wrap
- 55 Wrap Line Feed
- 56 Print on CR
- 56 Form Feed at TOF
- 56 Alt ESC (Alternate Escape)
- 56 Upper Only
- 57 Code 7F
- 57 Print 80 to 9F Hex
- 57 Ignore Char
- 57 Sub Char From
- 57 Sub Char To
- 57 PTX SFCC
- 57 PTX ALS
- 58 TOF Control
- 58 DC3 Operation
- 58 SISO OverszBar
- 58 Barcod Top Pos
- 58 Oversz Top Pos
- 59 Graphics Category
- 59 Code V Command Character (CVCC)
- 59 Smooth Size
- 59 PY Then
- 59 PN Then
- 59 Dark Bar
- 60 Table 3–1. Bar Code Dot Density
- 60 Modplot
- 60 Figure 3–2. Modplot Example
- 60 Version
- 60 Descender
- 61 Vertical Scale
- 61 Special Function Command Character (SFCC)
- 61 Code V Language
- 61 Free Format
- 62 Automatic PY
- 62 MTPL Bar
- 62 Secured
- 62 IGP Terminator
- 62 BlkMax H
- 62 BlkMax V
- 62 BlkMin H
- 62 BlkMin V
- 62 Postnet Density
- 62 PGL Terminator
- 63 Ignore Term
- 63 Configurations Category
- 63 How to Save Configurations
- 64 Powerup Config
- 64 Config n Label - (where n = 1 to 10)
- 64 How to label a configuration slot
- 65 Serial I/O Category
- 65 Data Bits
- 65 Stop Bits
- 65 Parity
- 65 8th Bit
- 65 Protocol
- 66 Status Enquiry
- 67 DTR Function
- 67 DTR Polarity
- 67 Busy Polarity
- 67 RTS Function
- 67 Robust Xon
- 68 Parallel I/O Category
- 68 POPC (Print On Paper Command)
- 68 8th Bit
- 68 Bi-Directional
- 69 Intellifilter Category
- 69 Serial
- 69 Parallel
- 69 Twinax/Coax
- 70 Twinax/Coax Category
- 70 Send PA (Coax Only)
- 70 Address (Twinax Only)
- 70 SPD (Coax Only)
- 70 SCD (Twinax Only)
- 71 Host (Font) Style (Twinax Only)
- 71 Screen Size (Screen) (Coax Only)
- 71 Case (Coax Only)
- 71 Compatibility Switches (Coax Only)
- 72 IR Delay (Coax Only)
- 72 Hex Passthrough
- 73 GrAVM (Graphics AVM)
- 74 IPDS Category (IPDS Only)
- 74 Address (Twinax Only)
- 74 Density
- 74 Dark Bar
- 74 Smooth Size
- 74 Host Override
- 75 TCP/IP Menu - LAN Interface Only
- 75 IP Address
- 75 Gateway
- 75 Subnet
- 76 Test Menu
- 76 Pattern Category
- 76 Print
- 76 Fault Override Category
- 76 Paper Motion
- 77 Diag Category
- 77 Cal-Paper (Calibrate Paper Out)
- 77 Help Menu