- Home
- Domestic appliances
- Climate control
- Temperature & humidity sensors
- Elis
- FLONET FH30 Series
- User manual
advertisement
Project design, installation and service manual
Electromagnetic flowmeter FLONET FH30xx
Page 7 of 72
ELIS PLZEŇ a. s.
documents and follow manufacturer’s instructions as described therein. Following the above mentioned instructions will prevent the loss of warranty for reasons of incorrect installation and misapplication.
Installation of this flowmeter shall be performed only by a company trained for this purpose by ELIS
PLZEŇ a.s. Such a company, after receiving the training, shall be fully responsible for the correct installation and commissioning. ELIS PLZEŇ a.s. bears no responsibility for defects in the product caused by an incorrect installation, its wrong application or incompetent configuration or programming.
These products, that ELIS PLZEŇ a. s. makes available on the market, are certified according to applicable standards. The accompanying documentation consists of Project design, installation and service manual and Declaration of Conformity . The products have a warranty as stated in the
Confirmation of Purchase Order or in the Purchase Contract .
All product manuals are regularly updated and the current version is delivered together with the product and also available on the Internet under www.elis.cz/en .
ELIS PLZEŇ a. s. shall have the sole right to update technical documentation for its products.
When ordering a flowmeter, the buyer shall provide all required parameters. ELIS PLZEŇ a.s., as the purchaser, s hall confirm the received Purchase Order and send it back together with manufacturer’s
General Terms and Conditions.
Deliveries of flowmeters shall be governed by the Czech Civil Code. The product is delivered pursuant to the confirmed Purchase Order or P urchase Contract. ELIS PLZEŇ a. s. is not responsible for differences in flowmeter parameters that were not confirmed in writing.
The following icons are used in the Project design, installation and service manual :
Warning : incorrect operation or erroneous flowmeter configuration may cause damage to product or injury to persons.
Information about another flowmeter features or types of documents delivered together with the product.
1.5 Product warranty
The flowmeter manufacturer provides product warranty in accordance with their valid commercial conditions.
Additional information regarding warranty is included in Chapter 14 hereof.
1.6 Representations and certificates
Applicable to electromagnetic flowmeters of the FLONET FH30xx type series are representations and certificates referred to in Chapter 17 below, namely:
•
Representation on CE compliance
ELIS PLZE Ň a. s., Luční 425/15, 301 00 Plzeň, Czech Republic, phone.: +420 377 517 711, fax: +420 377 517 722 Es 90678K
advertisement
Related manuals
advertisement
Table of contents
- 5 BASIC INFORMATION
- 5 Application
- 6 Meter properties and functions
- 6 Important user information
- 6 Safety instructions
- 6 Liability
- 7 Product warranty
- 7 Representations and certificates
- 8 METER IDENTIFICATION
- 8 FLONET FH30xx flowmeter type designation
- 8 Scope of delivery
- 8 Compact meter version FLONET FH30x
- 8 Remote meter version FLONET FH30x
- 9 Associated documents
- 9 Flowmeter rating plates
- 9 Main meter plate
- 9 Transmitter plate
- 10 Sensor plate
- 10 METER DESIGN AND MATERIAL VERSIONS
- 10 Compact and remote meter versions
- 12 Operating pressure of the measured fluid
- 14 Sensor dimensions
- 16 Sensor lining
- 16 Electrode materials
- 17 Sensors for flowmeters FLONET FH30xx; review of sensor design and material versions
- 18 INSTALLATION
- 18 Taking over
- 18 Meter handling
- 18 Storage
- 19 Installation conditions
- 19 General principles
- 19 Straight piping sections
- 20 Suppression of the pump effects
- 21 Suppression of the effects of closing valves
- 21 Suppression of vibration effects
- 22 Piping stacks
- 22 Sensor flooding
- 22 Free discharge points
- 23 Tightening torque
- 26 Thermal insulation
- 26 Flowmeter heating
- 50 Cable gland sizes
- 50 Company seals
- 51 Dimensions and weight
- 51 Sensor
- 51 Flanges according to EN
- 52 Flanges according to ASME B
- 53 Wafer sensor
- 54 Transmitter
- 54 Transmitter for compact meter version
- 54 – sensor protection class IP
- 55 Sensor connection box
- 56 FLOWMETER FAULTS
- 56 General rules
- 56 Spare PC boards and components
- 56 Software and simulation devices
- 57 Fault identification
- 58 Meter repair procedures
- 61 MAINTENANCE
- 61 SERVICES
- 61 WARRANTY
- 61 Warranty services
- 62 Post-warranty services
- 63 ORDER NUMBER
- 70 ASSOCIATED DOCUMENTS AND STANDARDS
- 71 ANNEXES
- 71 Representation on meter decontamination