- Home
- Domestic appliances
- Climate control
- Temperature & humidity sensors
- Elis
- FLONET FH30 Series
- User manual
advertisement
Project design, installation and service manual
Electromagnetic flowmeter FLONET FH30xx
Page 50 of 72
ELIS PLZEŇ a. s.
Sensor for compact meter version
In compact meter version, the transmitter is attached to the meter sensor by means of a steel column with a stainless-steel flange. This flange is provided with two threaded holes to facilitate connections for potential equalising conductors.
Sensor for remote meter version
Sensor manufactured in the standard protection class IP 67 includes a terminal box. In the case of the sensor protection class IP 68, the signal cable conductors are permanently connected to the sensor terminals and the terminals inside the connection box are embedded in an insulation compound. The other end of the signal cable is provided with a connector facilitating connection to the meter transmitter.
The flowmeter component parts made of carbon steel are coated with polyurethane paint, the connection box with powder paint. The surface finish of all-stainless-steel sensor housing consists of shot blasting.
Attached to the sensor housings are sensor rating plate and an arrow indicating the positive fluid flow direction.
The connections to the sensor terminal box are described in Chapter 5 (ELECTRICAL CONNECTIONS).
10.3 Cable gland sizes
Compact meter version
•
Transmitter terminal box is provided with 2 glands with threaded plugs
M20x1.5
Remote meter version
•
Transmitter: 2 pcs of glands M20x1.5
•
Sensor terminal box: 1 pc of gland M20x1.5
10.4 Company seals
Electromagnetic flowmeters of the type series FLONET FH30xx are supplied calibrated, verified as to their functions and with parameters set according to the customer’s order specifications. Upon completion of all fabrication and testing procedures, the meters are provided with the manufacturer’s
(company) seals.
Company seal
•
Upon closing the meter transmitter housing, the front lid including a viewing window is secured against opening or removal by a self-adhesive company seal.
•
In the cases of compact meter version, a self-adhesive company seal is applied onto the flanges connecting the meter transmitter and sensor.
If a company seal is broken, the user will forfeit their right to warranty services, i.e. free-ofcharge meter repair during the agreed product warranty period.
Assembly seal
Following electrical connection of the meter and closing the terminal compartment on the meter transmitter, the organisation responsible for the meter installation will secure the lid position by a self-adhesive seal.
ELIS PLZE Ň a. s., Luční 425/15, 301 00 Plzeň, Czech Republic, phone.: +420 377 517 711, fax: +420 377 517 722 Es 90678K
advertisement
Related manuals
advertisement
Table of contents
- 5 BASIC INFORMATION
- 5 Application
- 6 Meter properties and functions
- 6 Important user information
- 6 Safety instructions
- 6 Liability
- 7 Product warranty
- 7 Representations and certificates
- 8 METER IDENTIFICATION
- 8 FLONET FH30xx flowmeter type designation
- 8 Scope of delivery
- 8 Compact meter version FLONET FH30x
- 8 Remote meter version FLONET FH30x
- 9 Associated documents
- 9 Flowmeter rating plates
- 9 Main meter plate
- 9 Transmitter plate
- 10 Sensor plate
- 10 METER DESIGN AND MATERIAL VERSIONS
- 10 Compact and remote meter versions
- 12 Operating pressure of the measured fluid
- 14 Sensor dimensions
- 16 Sensor lining
- 16 Electrode materials
- 17 Sensors for flowmeters FLONET FH30xx; review of sensor design and material versions
- 18 INSTALLATION
- 18 Taking over
- 18 Meter handling
- 18 Storage
- 19 Installation conditions
- 19 General principles
- 19 Straight piping sections
- 20 Suppression of the pump effects
- 21 Suppression of the effects of closing valves
- 21 Suppression of vibration effects
- 22 Piping stacks
- 22 Sensor flooding
- 22 Free discharge points
- 23 Tightening torque
- 26 Thermal insulation
- 26 Flowmeter heating
- 50 Cable gland sizes
- 50 Company seals
- 51 Dimensions and weight
- 51 Sensor
- 51 Flanges according to EN
- 52 Flanges according to ASME B
- 53 Wafer sensor
- 54 Transmitter
- 54 Transmitter for compact meter version
- 54 – sensor protection class IP
- 55 Sensor connection box
- 56 FLOWMETER FAULTS
- 56 General rules
- 56 Spare PC boards and components
- 56 Software and simulation devices
- 57 Fault identification
- 58 Meter repair procedures
- 61 MAINTENANCE
- 61 SERVICES
- 61 WARRANTY
- 61 Warranty services
- 62 Post-warranty services
- 63 ORDER NUMBER
- 70 ASSOCIATED DOCUMENTS AND STANDARDS
- 71 ANNEXES
- 71 Representation on meter decontamination