How to access the FIPIO Agent parameters via PCMCIA cards. Schneider Electric PL7 Micro/Junior/Pro, Communication applications, Volume 2

PDF

Dokument

Reklama

Fipio Agent

How to access the FIPIO Agent parameters via PCMCIA cards

Introduction

How to access the link

The creation of an application setting up FIPIO Agents requires the configuration of the communication channel of the PLC registered as an FIPIO Agent.

This operation describes how to access the configuration parameters of the FIPIO

Agent link via the PCMCIA TSX FPP card for Micro/Premium PLCs.

The following table shows the procedure for accessing the FIPIO link:

Step

Action

Access the communication channel configuration screen.

From the dropdown menu, select the communication channel CHANNEL 1

Example

CHANNEL 1

(No PCMCIA submodule)

MAST

3 Select one of the following PCMCIA cards from the dropdown menu: z TSX FPP 10 PCMCIA CARD FIPIO

Example

CHANNEL 1

CHANNEL 1 (No PCMCIA submodule)

(Link not configured) MAST

TSX SCP 114 PCMCIA CARD RS485 MP

TSX FPP 20 PCMCIA FIPWAY CARD

TSX FPP 200 PCMCIA FIPWAY CARD

TSX FPP 10 PCMCIA FIPIO CARD

TSX MBP 100 PCMCIA MODBUS+ CARD

TSX MDM 10 PCMCIA MODEM CARD

35013154.02 07/2208

367

Fipio Agent

FIPIO Agent configuration screen

Introduction

Illustration

This screen, split into two areas, is used to register the communication channel and to configure the necessary parameters for a FIPIO Agent link.

The screen dedicated to communication looks like this:

TSX 3722 [POSITION 00.0..1]

Configuration

Designation: PROCESSOR 37222

CHANNEL 1

FIPIO AGENT

TSX FPP 10 PCMCIA FIPIO CARD

MAST

Connection Point Address

Table Start Address %MW 0

Elements and functions

This table describes the different areas that make up the configuration screen:

Address Zone

1 common

2 specific

Function

See (See : PL7 Micro/Junior/Pro ; Communication applications

; Volume 1).

is used to select and complete the following parameters: z z connection point address the beginning address of the table.

the beginning address of the table.

This parameter indicates the address of the table to be reserved for the periodic data exchanges between the bus manager and the FIPIO Agent.

The table has 64 words: z z

32 words for the inputs (%IW\p.2.c\m.i.r),

32 words for the outputs (%QW\p.2.c\m.i.r).

368

35013154.02 07/2208

Fipio Agent

25.3 Debugging Fipio Agents

FIPIO Agent debugging screen

Introduction

Illustration

This screen, split into two areas, is used to debug a FIPIO Agent.

The screen dedicated to debugging looks like this:

TSX 3722 [POSITION 00.0..1]

Debugging

Designation: PROCESSOR 37222 Version: 3.4

CHANNEL 1

FIPIO

TSX FPP 10 PCMCIAFIPIO CARD

MAST

FIPIO function status

State of output %MW

Active

Table addresses:

OUTPUT from: %MW300 to %MW331

INPUT from: %MW322 to %MW363

Access values via animation tables

DIAG...

Elements and functions

This table describes the different areas that make up the configuration screen:

Address Zone

1 common

2 specific

Function

See (See : PL7 Micro/Junior/Pro ; Communication applications

; Volume 1).

is used to access the debugging parameters of a FIPIO Agent.

No data can be accessed from this screen.

35013154.02 07/2208

369

Fipio Agent

25.4 Language objects associated with the Fipio

Agents

Introduction

Aim of this

Section

What's in this

Section?

This Section introduces the language objects associated with Fipio Agents.

This section contains the following topics:

Topic

Language objects in implicit exchange

Language object for explicit exchange

Explicit exchange management and reports

Language objects associated with configuration

Page

370

35013154.02 07/2208

Fipio Agent

Language objects in implicit exchange

Introduction

Bit objects

This page describes all the language objects for implicit exchange associated with the FIPIO communication agents that can be displayed or modified by the agent’s application program. (PL7 Micro/Junior/Pro ; Communication applications ;

Volume 1)

The table below shows the different bit objects for implicit exchange.

Object (1) Function

%Ixy.MOD.ERR Module error bit

%Ixy.i.ERR

Channel error bit

Meaning

This bit set to 1, indicates a module error (at least one of the channels is faulty,…)

This bit set to 1, indicates a line fault.

Key

(1) z z xy.i Address z x: corresponds to the rack number (-) y: corresponds to the module number (0/1) i: corresponds to the channel number (1)

Word objects The table below shows the different word objects for implicit exchange.

Object (1)

%IWxy.i.0

Function Meaning

Agent function status Byte 0: z = 16#01: IDLE function z z

= 16#02: RUN function

= 16 #03: STOP function

Strategy to be applied to outputs

Byte 1: z z z

= 16#01: safety

= 16#02: %MW value valid

= 16 #03: fallback

Key

(1) z z xy.i Address z x: corresponds to the rack number (-) y: corresponds to the module number (0/1) i: corresponds to the channel number (1)

35013154.02 07/2208

371

Fipio Agent

Language object for explicit exchange

Introduction

Word objects

This page describes all the language objects for explicit exchange associated with the FIPIO communication agents that can be displayed or modified by the application program. (See : PL7 Micro/Junior/Pro ; Communication applications ;

Volume 1)

The table below shows the different word objects for explicit exchange.

Object (1) Function

%MWxy.MOD.2

Module status

%MWxy.i.2

Standard channel status

Meaning z z z z z z z z x0 = 1: defective module x1 = 1: functional error (error between the processor and the module, adjustment or configuration error, …) x2 = 1: terminal block fault (not connected) x3 = 1: self-tests running x4 = 1: reserved x5 = 1: error in hardware or software configuration (the module present is not that declared in the configuration, the sub-modules are not compatible) x6 = 1: missing module x7 = 1: error in one of the sub-modules z z

Byte 0: z x0 = 1: input words are disabled when the manager is in RUN z x1 = 1: output words are disabled when the agent is in RUN z x4 = 1: internal error of TSX FPP 10 card or card z not yet started by the manager x5 = 1: configuration error (the configured data module is different from that present) x6 = 1: communication error on FIPIO x7 = 1: application error (%MW table overrun)

Byte 1: reserved

Key

(1) xy.i Address z z z x: corresponds to the rack number (-) y: corresponds to the module number (0/1) i: corresponds to the channel number (1)

372

35013154.02 07/2208

Fipio Agent

Explicit exchange management and reports

Introduction

Word objects

This page describes all the language objects that manage explicit exchanges. (See

: PL7 Micro/Junior/Pro ; Communication applications ; Volume 1)

The table below shows the different word objects for the management of explicit exchanges.

Object (1)

%MWxy.MOD.0

%MWxy.MOD.1

%MWxy.i.0

Function

Module exchanges in progress

Module report

Meaning z z z x0 = 1: reading status in progress x1 = 1: sending of command parameters to the communication module x2 = 1: sending of adjustment parameters to the communication module z z x1 = 0: command parameters received and accepted by the module x2 = 0: adjustment parameters received and accepted by the module

Channel exchanges in progress z z z x0 = 1: reading status in progress x1 = 1: sending of command parameters to the communication channel x2 = 1: sending of adjustment parameters to the communication channel

%MWxy.i.1

Channel report z z x1 = 0: command parameters received and accepted by the communication channel x2 = 0: adjustment parameters received and accepted by the communication channel

Key

(1) z z z xy.i address x: corresponds to the rack number (-) y: corresponds to the module number (0/1) i: corresponds to the channel number (1)

35013154.02 07/2208

373

Fipio Agent