Printing Using PictBridge
6
By connecting the camera to a printer that supports PictBridge using the
USB cable (I-USB7) provided, you can print images directly from the camera without using a PC. Connect the camera to the printer and select the images you want to print and the number of copies on the camera.
• You are recommended to use the AC adapter kit K-AC78 when the camera is connected to the printer. The printer may not work properly or the image data may be lost if the battery runs out of power while the camera is connected to the printer.
• Do not disconnect the USB cable during data transfer.
• Depending on the model of printer, not all the settings made on the camera (such as print settings and DPOF settings) may be valid.
• A printing error may occur if the selected number of copies exceeds 500.
• Printing the index of the images (printing multiple images on a single sheet) cannot be performed directly from the camera. Make the settings on a printer supporting index printing function or use a PC.
Connecting the Camera to the Printer
1
Select [PictBridge] for the [USB Connection] mode on the [ W Setting] menu.
Refer to “Changing the USB Connection Mode” (p.171).
2
Turn off the camera.
3
Connect the camera to the printer using the USB cable provided.
4
Turn the printer on.
5
When the printer is ready to print, turn the camera on.
The printing mode selection screen appears.
A l l I m a g e s
S i n g l e I m a g e
DPOF AUTOPRINT
OK
152
Printing Single Images
1
In the printing mode selection screen, use the four-way controller ( 23 ) to select [Single
Image].
2
Press the 4 button.
The setting screen appears.
3
Use the four-way controller ( 45 ) to choose an image to print.
4
Use the four-way controller ( 23 ) to choose the number of copies.
You can print up to 99 copies.
5
Use the Green button to choose whether to insert the date or not.
O (On) : The date will be imprinted.
P (Off) : The date will not be imprinted.
6
Press the 4 button.
A confirmation dialog appears.
To print the pictures according to the print settings on the printer, press the 4 button.
To change the print settings, go to Step 7.
7
Press the Green button.
The screen for changing the print settings appears.
8
Select [Paper Size] and press the four-way controller ( 5 ).
The Paper Size screen appears.
MENU
A l l I m a g e s
S i n g l e I m a g e
DPOF AUTOPRINT
OK
C o p i e s 0 1 D a t e
P a p e r S i z e
P a p e r Ty p e
Q u a l i t y
B o r d e r S t a t u s
MENU
P i c t B r i d g e
P a p e r S i z e
P a p e r Ty p e
Q u a l i t y
B o r d e r S t a t u s
MENU
OK
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
OK
Setting
Setting
Setting
Setting
6
153
6
9
Use the four-way controller
( 2345 ) to choose the paper size.
You can only choose a size that is supported by your printer.
10
Press the 4 button.
P a p e r S i z e
S e t t i n g
C a r d
L
1 0 0 × 1 5 0
P o s t c a r d
4 ” × 6 ”
MENU
2 L
8 ” × 1 0 ”
A 4
L e t t e r
1 1 ” × 1 7 ”
A 3
OK
The Paper Size setting is saved, and the screen returns to the print settings screen.
11
Use the four-way controller ( 23 ) to select [Paper Type] and press the four-way controller ( 5 ).
A pull-down menu appears.
12
Use the four-way controller ( 23 ) to select the paper type and press the 4 button.
The Paper Type setting is saved, and the screen returns to the print settings screen. Set [Quality] and [Border Status] in the same way as in Steps 11 and 12.
If you select [ _ Setting] for each print setting, images are printed according to the settings made on the printer.
Paper Type with more E supports higher quality paper.
Quality with more E indicates higher print quality.
A confirmation dialog appears after each item has been set.
13
Press the 3 button.
The screen returns to the confirmation dialog.
14
Press the 4 button.
The image is printed according to the settings.
Press the 3 button to cancel printing.
• The self-timer lamp lights while the camera is communicating with the printer, and blinks while the card is being accessed and during printing. Do not disconnect the USB cable while the self-timer lamp is blinking.
• The [Paper Size], [Paper Type], [Quality] and [Border Status] settings are reset to the defaults when the camera is turned off.
• If the picture already has the date imprinted on it (p.105), do not
set Date O (On) in DPOF settings. Otherwise, the date could be imprinted twice on your printed picture.
Disconnecting the Cable from the Printer
1
p.156
154
Printing All Images
1
In the printing mode selection screen, use the four-way controller ( 23 ) to select [All
Images].
A l l I m a g e s
S i n g l e I m a g e
DPOF AUTOPRINT
OK
2
Press the 4 button.
The setting screen appears.
3
Choose the number of copies and whether to insert the date or not.
C o p i e s
T o t a l
The number of copies and date setting that you choose apply to all the images.
Refer to Steps 4 and 5 in “Printing Single
MENU
Images” (p.153) for details of how to make the settings.
4
Press the 4 button.
0 1
2 8
D a t e
OK
A confirmation dialog appears.
Refer to Steps 7 to 11 of “Printing Single Images” (p.153 and p.154) for
details of changing print settings.
5
Press the 4 button on the print settings confirmation screen.
All the images are printed according to the settings.
Press the 3 button to cancel printing.
6
If the pictures already have the date imprinted on them (p.105), do
not set Date O (On) in DPOF settings. Otherwise, the date could be imprinted twice on your printed pictures.
155
6
Printing Using the DPOF Settings
1
In the printing mode selection screen, use the four-way controller ( 23 ) to select [DPOF AUTOPRINT].
2
Press the 4 button.
The DPOF settings you have made appear.
Use the four-way controller ( 45 ) to check the number of copies for each picture, whether to insert the date or not, and the
total number of copies. Refer to p.149 for
instructions on how to make the DPOF settings.
3
Press the 4 button.
MENU
C o p i e s
T o t a l
0 1
1 0
D a t e
OK
A confirmation dialog appears.
Refer to Steps 7 to 11 of “Printing Single Images” (p.153 and p.154) for
details of changing print settings.
4
Press the 4 button.
The images are printed according to the settings.
Press the 3 button to cancel printing.
If the picture already has the date imprinted on it (p.105), do not set
Date O (On) in DPOF settings. Otherwise, the date could be imprinted twice on your printed picture.
Disconnecting the Cable from the Printer
Disconnect the USB cable from the camera and printer when you have finished printing.
1
Turn off the camera.
2
Disconnect the USB cable from the camera and printer.
156
