advertisement
Add or Remove a Trolling Grid: From the Waypoints submenu (accessed from the Navigation main menu), select Grid and press the RIGHT Cursor key to display a list of waypoints. Select the waypoint to which you want to add the grid. The trolling grid will appear on all of the navigation views, and can be used as a guide when trolling around a waypoint. The grid can be rotated to any desired heading using Grid Rotation from the Navigation Main menu. To remove the trolling grid, choose Remove Grid from the Navigation X-Press™ Menu.
Chart View with Grid
1
2
1
Map Scale Waypoint Trolling Grid
2
NOTE: Only one waypoint can have either a target or a grid at one time. If you apply a target or a grid to a new waypoint, the original waypoint will lose its target or grid.
NOTE: The spacing of the rings on the waypoint target and the spacing of the grid lines on the trolling grid is the same as the length of the scale bar on the left edge of the display. Zooming in or out will decrease or increase the spacing, respectively.
55
Save, Edit or Delete a Route
Save the current route: While you are navigating, the current route can be saved. From the Navigation X-Press™ Menu, select Save Current Route and press the RIGHT Cursor key. Navigation will continue.
Display the Routes submenu: From any view, press the MENU key twice to display the Main Menu System, then use the RIGHT Cursor key to select the
Navigation tab. Select Routes and press the RIGHT Cursor key to display the
Routes submenu.
Create a route: From the Routes submenu, select Create and press the
RIGHT Cursor key. A Route Edit screen will be displayed with an empty route.
You can name the route, add waypoints to the route from the list of all waypoints, and order the waypoints in the route using the Cursor keys.
Edit a saved route: From the Routes submenu, select Edit and press the
RIGHT Cursor key. A Route Edit screen will be displayed. Select the route you wish to edit and press the RIGHT Cursor key. Re-name the route or change, delete or re-order the waypoints used in the route.
Delete a saved route: From the Routes submenu, select Delete and press the RIGHT Cursor key. Select the route you wish to delete and press the
RIGHT Cursor key. You will be asked to confirm your choice by pressing the
RIGHT Cursor key again before the route is deleted.
Travel a saved route: From the Routes submenu, select Travel and press the
RIGHT Cursor key. A list of saved routes will appear. Select the route you wish to travel and press the RIGHT Cursor key to make this route the current route and begin navigation. You may also travel the route in either forward or reverse order.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 How the 900 Series™ Works
- 10 3D Sonar
- 10 2D Sonar
- 11 How GPS and Cartography Work
- 12 Multi-Media Card (MMC)/SD Slot
- 12 Software Updates
- 12 Accessory Bus
- 14 Gimbal Mounting the Control Head
- 19 Connecting the Control Head Power Cable to the Boat
- 20 Transom Transducer Installation
- 25 Inside the Hull Transducer Installation
- 28 Trolling Motor Transducer Installation
- 28 Trolling Motor Transducer Options
- 28 Test and Finish the Transducer Installation
- 30 Stem Mounting with an Existing 1" - 14 Thread Stem
- 31 Access Under Mounting Location
- 31 No Access Under Mounting Location
- 32 Finish Routing the Cable and Check GPS Receiver Operation
- 33 Temperature Probe Accessory Installation
- 35 Powering Up the Control Head
- 36 What’s on the 3D Sonar Display
- 37 What's on the 2D Sonar Display
- 38 Real Time Sonar (RTS®) Window
- 38 Bottom Presentation
- 39 POWER/LIGHT Key
- 40 VIEW Key
- 40 MENU Key
- 41 4-WAY Cursor Control Key
- 41 View Preset Keys
- 41 EXIT Key
- 42 INFO Key
- 42 MARK Key
- 42 GOTO Key
- 43 ZOOM (+/-) Keys
- 43 Views and Readouts
- 44 3D/2D Combo View
- 45 2D Sonar View
- 46 2D Zoom View
- 47 6-Beam Sonar View
- 48 Snapshot and Recording View
- 52 Bird’s Eye View
- 53 Chart/Bird’s Eye Combo View
- 54 Chart/Chart Combo View
- 55 Chart View
- 56 Chart/3D Combo View
- 57 Chart/2D Combo View
- 58 Chart Orientation
- 60 Waypoints, Routes and Tracks
- 61 Save, Edit, or Delete a Waypoint
- 62 Navigate to a Waypoint or Position
- 62 Add a Waypoint Target or Trolling Grid
- 63 Save, Edit or Delete a Route
- 64 Save or Clear a Current Track
- 64 Edit, Delete or Hide Saved Tracks
- 65 Man Overboard (MOB) Navigation
- 68 Normal Operation
- 68 Simulator
- 68 System Status
- 69 Self Test
- 69 Accessory Test
- 70 GPS Diagnostic View
- 71 Active Side
- 72 Split Position
- 72 Sensitivity
- 73 Lower Range
- 74 Chart Speed
- 75 2D/3D Priority
- 76 Active Side
- 76 Split Position
- 77 3D Bottom Zoom
- 77 3D Lower Range
- 78 3D History
- 78 Reset 3D View
- 78 2D/3D Priority
- 80 Active Side
- 80 Split Position
- 81 Save Current Track
- 81 Clear Current Track
- 89 2D Sonar Colors
- 89 3D Bottom Style
- 90 3D Frame Style
- 90 2D Beam Select
- 90 Fish ID
- 91 Fish ID Sensitivity
- 91 Fish ID 3D Reference
- 92 Real Time Sonar (RTS®) Window
- 92 Bottom View
- 93 83 kHz Sensitivity
- 96 Color Bar
- 97 Current Track
- 97 Saved Tracks
- 98 Waypoints
- 98 Routes
- 99 Chart Orientation
- 99 North Reference
- 99 Trolling Grid Rotation
- 100 Trackpoint Interval
- 101 Track Color Range
- 101 Course Projection Line
- 102 Continuous Navigation Mode
- 103 Chart Detail Level
- 103 Map Borders
- 104 Lat/Lon Grid
- 104 Spot Soundings
- 104 Navaids on Bird's Eye View
- 104 Shaded Depth
- 107 Depth Alarm
- 107 Fish ID Alarm
- 107 Low Battery Alarm
- 108 Temp Alarm
- 109 Off Course Alarm
- 109 Arrival Alarm
- 110 Drift Alarm
- 110 Alarm Tone
- 111 Units - Depth
- 113 Restore Defaults