advertisement
1
1,2 3
TIMER
-MODE
–TIME
WAKE
WAKE
2
TIMER
-MODE
–TIME
WAKE
TUNED STEREO
WAKE
A
SPEAKERS
3
SLEEP
MHz
Timer function
There are two timer functions: the sleep timer and the wake timer.
¡
Sleep timer:
The unit turns off after a set time.
It can be set for 30, 60, or 90 minutes.
¡
Wake timer:
The unit can be set to turn on a certain number of hours after it is turned off.
It can be set for 5, 7, or 9 hours.
Setting the timers
1
Press [TIMER, -MODE, –TIME] to select the desired timer mode.
Each time you press the button, the timer mode changes.
2
[Within 5 seconds]
Press [TIMER, -MODE, –TIME] and release when the time you require is displayed.
The display changes as follows:
¡
In sleep timer mode
30 60 90 (minutes)
¡
In wake timer mode
5H 7H 9H (hours)
The display is restored 5 seconds after the setting is completed.
3
Wake timer mode only
Press [ /l] to turn off the unit.
The “WAKE” indicator lights up.
Checking the remaining time on the sleep timer and the time set for the wake timer
Press [TIMER, -MODE, –TIME] once.
Note
Do not press [TIMER, -MODE, –TIME] again before the remaining time indication goes out.
The setting may change if you do this.
Changing a setting
Repeat steps 1 and 2.
To cancel the timer
Press [TIMER, -MODE, –TIME] until “OFF” is displayed.
“SLEEP” or “WAKE” will go out.
Note
¡
The timers cannot be used together.
¡
The sleep timer turns off the receiver, and the wake timer turns on the receiver, but they do not turn off/on any externally connected components.
49
RQT5518
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Front Page
- 2 Table of contents
- 3 Caution for AC Mains Lead
- 4 Safety precautions
- 5 To enjoy surround sound
- 6 Front panel controls
- 8 Remote control
- 9 Concerning the remote control
- 10 Connections
- 10 Connecting a DVD player
- 11 Connecting video equipment
- 12 Connecting audio equipment
- 12 Antenna connections
- 13 Connecting the AC mains lead and other information
- 14 Speaker connections
- 14 Placement of speakers
- 14 Connecting speakers
- 17 Preparatory steps
- 17 Speaker settings
- 19 Adjusting speaker output level
- 20 DSP sound modes
- 22 Enjoying the sounds
- 24 To enjoy bi-amp sound
- 25 To adjust the tone quality
- 25 To adjust the sound balance
- 25 When using the VCR 3 terminals
- 26 Switching DVD analogue input
- 27 VGCA mode
- 28 The radio
- 28 Sequential tuning
- 29 Direct tuning
- 30 Preset tuning
- 32 RDS broadcasts Only for the United Kingdom
- 36 Other functions
- 36 To listen through headphones
- 36 Dynamic range compression
- 37 To mute the sound level
- 37 When using the unit in a darkened room
- 38 The remote control
- 39 To operate the receiver
- 41 To operate a CD player or MD deck
- 41 To operate a cassette deck
- 43 To watch TV broadcasts
- 43 To watch video tapes
- 45 To operate a DVD player
- 46 To change the remote control code
- 48 Making a recording
- 48 Recording on a tape deck or VCR
- 49 Timer function
- 49 Setting the timers
- 50 Troubleshooting guide
- 51 The RESET function
- 51 Maintenance
- 52 Specifications