advertisement
One Touch Operation
This receiver can memorize the optimum sound settings for each playing source.
About the One Touch Operation
JVC’s One Touch Operation function is used to assign and store different sound settings for each different playing source. By using this function, you do not have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled.
The following can be stored for each source:
• Volume level (see page 15)
• Input attenuator mode (see page 17)
• Subwoofer output level (see page 17)
• Input mode (see page 18)
• Balance (see page 19)
• Loudness (see page 19)
• SEA modes (see page 32)
• DSP modes
– 3D-PHONIC mode settings (see page 35)
– DAP mode settings (see page 38)
– Surround mode settings (see page 40 and 43)
Using the One Touch Operation
On the front panel only:
To store the sound settings
1. Press ONE TOUCH OPERATION.
The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled.
2. Adjust the sound using the functions listed above.
The newly adjusted settings are memorized.
ONE TOUCH OPERATION
To recall the sound settings
With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source is recalled when the source is selected.
To cancel the One Touch Operation function
Press ONE TOUCH OPERATION so that the lamp goes off.
(Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)
ONE TOUCH OPERATION
Note:
If the source is FM or AM (MW/
LW), you can assign a different setting for each band.
23
Downloaded from www.Manualslib.com
manuals search engine
EN14_23.RX-884R[E]/1.PM5
23 98.3.26, 0:04 PM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 Parts Identification
- 9 Getting Started
- 9 Before Installation
- 9 Checking the Supplied Accessories
- 10 Connecting the FM and AM (MW/LW) Antennas
- 11 Connecting the Speakers
- 14 Connecting Audio/Video Components
- 18 Connecting the Power Cord
- 18 Putting Batteries in the Remote Control
- 19 Basic Operations
- 19 Turning the Power On and Off (Standby)
- 19 Selecting the Source to Play
- 20 Adjusting the Volume
- 21 Selecting the Front Speakers
- 21 Muting the Sound
- 21 Recording a Source
- 22 Attenuating the Input Signal
- 22 Adjusting the Subwoofer Output Level
- 23 Basic Settings
- 23 Changing the Source Name
- 23 Selecting the Input Mode
- 24 Adjusting the Front Speaker Output Balance
- 24 Setting the Subwoofer Information
- 24 Listening at Low Volume (Loudness)
- 25 Digital Input (DIGITAL IN) Terminal Setting
- 25 Setting the Speakers for the DSP Modes
- 28 One Touch Operation
- 28 About the One Touch Operation
- 28 Using the One Touch Operation
- 29 Receiving Radio Broadcasts
- 29 Tuning in Stations Manually
- 29 Using Preset Tuning
- 30 Selecting the FM Reception Mode
- 31 Assigning Names to Preset Stations
- 32 Using the RDS (Radio Data System) to Receive FM Stations
- 32 What Information Can RDS Signals Provide?
- 33 Searching for a Program by PTY Codes
- 35 Switching to a Broadcast Program of Your Choice Temporarily
- 37 Using the SEA Modes
- 37 Selecting Your Favorite SEA Mode
- 38 Creating Your Own SEA Mode
- 39 Using the DSP Modes
- 40 Using the 3D-PHONIC Modes
- 43 Using the DAP Modes
- 45 Using the Dolby Digital and Dolby Pro Logic Modes
- 48 Using the Theater Surround Mode
- 52 Using the On-Screen Menus
- 52 Selecting the Source to Play
- 52 Selecting the Different Sources for Picture and Sound
- 52 Using the DSP Modes
- 53 Adjusting the Front Speaker Output Balance
- 53 Listening at Low Volume (Loudness)
- 53 Attenuating the Input Signal
- 54 Adjusting the Subwoofer Output Level
- 54 Adjusting the DSP Modes
- 55 Selecting Your Favorite SEA Mode
- 56 Creating Your Own SEA Mode
- 56 Basic Settings
- 57 Operating the Tuner
- 57 Storing the Preset Stations
- 58 Assigning Names to the Preset Stations
- 59 Checking the RDS Information
- 60 COMPU LINK Remote Control System
- 61 TEXT COMPU LINK Remote Control System
- 62 Showing the Disc Information on the TV Screen
- 63 Searching a Disc (Only for the CD Player)
- 65 Using the User File (Only for the CD Player with the User File Function)
- 66 Entering the Disc Information
- 68 Operating JVC’s Audio/Video Components
- 72 Operating Other Manufactures’ Components
- 79 Troubleshooting
- 80 Specifications