advertisement
Using the On-Screen Menus
You can use the menus on the TV screen to control the receiver.
To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page
10), and set the TV’s input mode to the proper position to which the receiver is connected.
Selecting the Source to Play
(Also see page 14)
1. Press any button of ON SCREEN CONTROL
% / fi / @ / # once.
The MAIN MENU appears on the TV.
MAIN MENU
SOURCE :ch 1 FM 87.50MHz
VISUAL :VCR1
MODE :OFF
**
**
:OPERATE
VOLUME : 20
MAIN MENU
Shows the buttons you can use on the current menu.
In this case, use
%
/ fi
to move up and down, and
@
/
#
to select, adjust or set the item.
2. Press ON SCREEN CONTROL
% / fi to move
to “SOURCE.”
3. Press ON SCREEN CONTROL
@ / # to select the source.
4. When you finish, press EXIT.
The menu disappears from the TV.
Notes
• The on-screen display will disappear if no operation is done for about one minute.
• If your TV is not of the PAL color system, the TV screen will be distorted.
Selecting the Different Sources for Picture and Sound
You can view the pictures played back on a video component while listening to any source.
1. Press any button of ON SCREEN CONTROL
% / fi / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL
% / fi to move
to “VISUAL.”
3. Press ON SCREEN CONTROL
@ / # to select a different video source.
• When you select “OSD,” see page 56.
4. When you finish, press EXIT.
The menu disappears from the TV.
MAIN MENU
MAIN MENU
SOURCE :PHONO
VISUAL :VCR1
MODE :OFF
**
**
VOLUME : 20
**
**
:OPERATE
Using the DSP Modes
(Also see pages 35, 38, 40, and 43)
1. Press any button of ON SCREEN CONTROL
% / fi / @ / # once.
The MAIN MENU appears on the TV.
2. Press ON SCREEN CONTROL
% / fi to move
to “MODE.”
3. Press ON SCREEN CONTROL
@ / # to select the DSP mode you want to use.
4. When you finish, press EXIT.
The menu disappears from the TV.
MAIN MENU
MAIN MENU
SOURCE :VCR1
VISUAL :VCR1
MODE :PRO LOGIC
**
**
:OPERATE
VOLUME : 20
47
Downloaded from www.Manualslib.com
manuals search engine
EN47_62.RX-884R[E]/1.PM5
47 98.3.26, 1:02 PM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 8 Parts Identification
- 9 Getting Started
- 9 Before Installation
- 9 Checking the Supplied Accessories
- 10 Connecting the FM and AM (MW/LW) Antennas
- 11 Connecting the Speakers
- 14 Connecting Audio/Video Components
- 18 Connecting the Power Cord
- 18 Putting Batteries in the Remote Control
- 19 Basic Operations
- 19 Turning the Power On and Off (Standby)
- 19 Selecting the Source to Play
- 20 Adjusting the Volume
- 21 Selecting the Front Speakers
- 21 Muting the Sound
- 21 Recording a Source
- 22 Attenuating the Input Signal
- 22 Adjusting the Subwoofer Output Level
- 23 Basic Settings
- 23 Changing the Source Name
- 23 Selecting the Input Mode
- 24 Adjusting the Front Speaker Output Balance
- 24 Setting the Subwoofer Information
- 24 Listening at Low Volume (Loudness)
- 25 Digital Input (DIGITAL IN) Terminal Setting
- 25 Setting the Speakers for the DSP Modes
- 28 One Touch Operation
- 28 About the One Touch Operation
- 28 Using the One Touch Operation
- 29 Receiving Radio Broadcasts
- 29 Tuning in Stations Manually
- 29 Using Preset Tuning
- 30 Selecting the FM Reception Mode
- 31 Assigning Names to Preset Stations
- 32 Using the RDS (Radio Data System) to Receive FM Stations
- 32 What Information Can RDS Signals Provide?
- 33 Searching for a Program by PTY Codes
- 35 Switching to a Broadcast Program of Your Choice Temporarily
- 37 Using the SEA Modes
- 37 Selecting Your Favorite SEA Mode
- 38 Creating Your Own SEA Mode
- 39 Using the DSP Modes
- 40 Using the 3D-PHONIC Modes
- 43 Using the DAP Modes
- 45 Using the Dolby Digital and Dolby Pro Logic Modes
- 48 Using the Theater Surround Mode
- 52 Using the On-Screen Menus
- 52 Selecting the Source to Play
- 52 Selecting the Different Sources for Picture and Sound
- 52 Using the DSP Modes
- 53 Adjusting the Front Speaker Output Balance
- 53 Listening at Low Volume (Loudness)
- 53 Attenuating the Input Signal
- 54 Adjusting the Subwoofer Output Level
- 54 Adjusting the DSP Modes
- 55 Selecting Your Favorite SEA Mode
- 56 Creating Your Own SEA Mode
- 56 Basic Settings
- 57 Operating the Tuner
- 57 Storing the Preset Stations
- 58 Assigning Names to the Preset Stations
- 59 Checking the RDS Information
- 60 COMPU LINK Remote Control System
- 61 TEXT COMPU LINK Remote Control System
- 62 Showing the Disc Information on the TV Screen
- 63 Searching a Disc (Only for the CD Player)
- 65 Using the User File (Only for the CD Player with the User File Function)
- 66 Entering the Disc Information
- 68 Operating JVC’s Audio/Video Components
- 72 Operating Other Manufactures’ Components
- 79 Troubleshooting
- 80 Specifications