- No category
advertisement
To turn the energy saver Off, select 0 (OFF). To turn the energy saver On, select 1 (ON). To turn the energy saver On or Off for a specific duration, select 9 (TIME) prior to selecting On or Off. Enter the time as described under Control - Unit Commands.
Downstairs
0=OFF 1=ON 2=HEAT
↓
Downstairs
3=COOL 9=TIME #=STAT
↑
TIME
MINUTES (1-99) #=H/M/S
Downstairs FOR 15M
0=OFF 1=ON
↓
The current status of a temperature zone may be displayed by selecting ' # ' (STAT) key from the main temperature menu. The status display differs depending on the temperature zone type.
When you are finished, press the ' * ' key twice to return to the top-level display.
IMPORTANT NOTES:
¾ There is a 3-minute minimum on and off time for PESMs designed to prevent short cycling your HVAC compressor. If the PESM has just turned the HVAC system on or off, it will wait 3 minutes before changing it, even though the display does change.
¾ If you change the Heat or Cool setback temperature on the PESM, the system will insure that there is always at least four degrees Fahrenheit difference between the Heat and Cool temperatures by altering the other setback temperature as necessary.
¾ PESMs are NOT affected by All On or All Off commands.
Freeze Alarms
Thermostats and PESMs can also be used to report potential freeze conditions before damage to pipes and appliances can occur.
An alarm is activated when any Thermostat or PESM detects a temperature below 40 degrees. The alarm will not clear until the temperature exceeds 45 degrees.
When the alarm is initiated, the console beeper will be turned on and an alarm dial-out sequence will be initiated after the normal dial-out delay. Both voice and digital communicator dial-outs may be used. The voice dial-out will follow the Dial Order as specified in Set Up Dial. The digital communicator will report the Freeze Alarm Code to the Central Station.
The sounder is not activated for freeze alarms (this feature must be activated by your installer).
Indoor and Outdoor Temperature
The Model 31A00-1 Temperature Sensor is used for sensing temperatures from 0º F - 120º F and 31A00-7 Extended Range
Temperature Sensor is used for sensing temperatures from -40º F - 120º F. It features a new, high accuracy temperature sensor that doesn’t need calibration.
The temperature can be used to activate programs for controlling temperatures indoors and in attics, garages, greenhouses, basements, wine cellars, coolers, and freezers. The temperature can be displayed on the console or spoken over the telephone. It can also report, log, alert, or generate an alarm if the temperature reaches freeze conditions or if the temperature goes above the high setpoint or drops below the low setpoint programmed in the system.
Outdoor temperature zones have a High and Low temperature associated with them that can be used for control purposes. An example of this is to program the system to turn on the bathroom heat if the outdoor temp goes below 45 degrees. High and Low temperatures are changed the same way as a PESM.
Page 34
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Underwriter's Laboratories (UL) Listing
- 10 Console Operation
- 11 Normal Top-Level Display
- 11 Display Menus
- 12 Main Menu
- 12 Error Beeps
- 12 Trouble Beeps
- 13 Confirmation Beep
- 13 Cancel
- 13 Time Out
- 13 Areas
- 13 Omni IIe Maintenance
- 14 Disarming the Security System and Silencing Alarms
- 14 Arming the Security System
- 15 Using Shortcut Keys
- 15 Quick Arm
- 16 What Happens When You Arm the Security System
- 16 Exit Error
- 17 Bypassing Zones
- 17 Auto-Bypass
- 17 Restoring Zones
- 18 What To Do When You Come Home
- 18 What Happens When the Alarm is Activated
- 18 Burglar Alarm Activated
- 19 Fire Alarm Activated
- 19 Gas Alarm Activated
- 19 Emergency Keys
- 20 Police Emergency
- 20 Fire Emergency
- 20 Auxiliary Emergency
- 20 Duress Code Entered or Duress Alarm Activated
- 20 Alarm Reset
- 20 Alarm Cancel
- 21 Trouble Indications
- 21 Codes
- 21 Master Code
- 22 Manager Code
- 22 User Code
- 22 Duress Code
- 22 Panic Switches
- 22 Area Arming
- 23 GOTO Area
- 24 Testing Your System
- 25 Control Commands
- 25 About UPB
- 26 HAI Lighting Control (HLC) Format
- 26 About Rooms
- 26 About Room Controllers
- 26 Room Controller LED Indicators
- 27 About House Controllers
- 27 About CentraLite
- 27 About Lutron RadioRA
- 28 About ALC
- 28 ALC Module Types
- 28 About X
- 28 House Codes
- 29 Unit Numbers
- 29 Scrolling Through Names
- 29 Controlling Units
- 29 Controlling a Room of HLC Lighting
- 30 Configuring Lighting Scenes in an HLC Room
- 30 Controlling Individual Lighting Loads in an HLC Room or UPB Units
- 31 Controlling CentraLite Units
- 31 Controlling RadioRA Units
- 31 Controlling ALC or X-10 Units
- 32 Ramp Command (ALC)
- 32 Controlling Compose Units
- 33 Scene Command (Compose)
- 33 Timed Commands
- 33 Status of a Unit
- 33 Internal Flags
- 34 Controlling Outputs
- 34 All On / Off
- 35 All Lights On
- 35 All Off
- 35 Leviton Scene Control
- 35 Scene
- 36 Scene Commands
- 36 Scene Set Command
- 36 Scene On Command
- 36 Scene Off Command
- 36 UPB Links
- 37 Activating and Deactivating Links
- 37 Setting a Link (Lighting Scenes)
- 37 Executing Phantom Buttons
- 37 Executing CentraLite Scenes
- 38 Buttons
- 38 Temperature Control
- 39 HAI RC-Series Thermostats
- 40 Programmable Energy Saver Modules (PESMs)
- 42 Freeze Alarms
- 42 Indoor and Outdoor Temperature
- 43 Temperature Control of Appliances
- 43 Temperature Alarms
- 43 Humidity
- 44 Status
- 44 Configuring HLC Devices
- 44 Configuring HLC Devices using an Omni Console
- 45 Configuring HLC Devices using an OmniTouch Touchscreen
- 45 Setup Mode for HLC Devices
- 47 Event Log
- 48 Show Events
- 48 Messages
- 48 Show Message
- 49 Log Message
- 49 Clear Message
- 49 Say Message
- 49 Phone Message
- 49 Send Message (Pro-Link)
- 51 Telephone Interface
- 51 In-House Phones
- 51 Remote Phones
- 52 Phone Access Denied - Remote Lockout
- 52 Alternate Method
- 52 Main Menu
- 53 1 - Control
- 53 2 - Security
- 53 GOTO Area
- 53 3 - Button
- 53 4 - All
- 53 5 - Temperature
- 54 6 - Status
- 54 7 - Events
- 55 8 - Phone
- 55 9 - Good-Bye
- 55 Panic Button over the Phone (# # # # # #)
- 56 Emergency Dial-Out
- 56 Digital Dialer
- 56 Voice Dialer
- 56 How the Omni IIe Voice Dialer Works
- 56 What the Omni IIe Voice Dialer Does
- 57 What You Hear - If Your Omni IIe Calls You
- 57 Entering the Code
- 58 Built-In Ethernet Port
- 58 Controller IP Address, Port Number, and Encryption Key
- 58 Omni IIe Ethernet Connections
- 58 Connecting to Network via PC Access
- 59 Dynamic DNS
- 61 Configuration and Advanced Control Programming (ACP)
- 61 Set Up Codes
- 61 Authority Level
- 61 AUTHORITY
- 61 1 = Master
- 61 2 = Manager
- 61 3 = User
- 62 Access Areas
- 62 Duress Code
- 62 Set Up Time
- 63 Advanced Control Programming (ACP)
- 64 1 = Add Programs
- 64 2 = Show Programs
- 65 3 = Delete All Programs
- 65 Edit Programs
- 66 Edit Programs When
- 66 Times Programs
- 67 Button and Event Programs
- 67 Control Unit / Switch Press Event Buttons
- 68 Security Mode Event Buttons
- 69 Zone Event Buttons
- 69 All On/Off Event Buttons
- 70 UPB Link Event Buttons
- 70 Alarm Event Buttons
- 70 X-10 Event Buttons
- 71 Miscellaneous Event Buttons
- 71 Message Event Buttons (Pro-Link)
- 72 Switch Press Event Buttons (CentraLite)
- 72 Edit Program Command
- 72 Program Control Commands
- 73 Unit Toggle Command
- 73 Program Security Commands
- 74 Program Button Commands
- 74 Program All On / All Off Commands
- 74 Program Video Commands
- 74 Program Temperature Commands
- 74 Program Energy Cost
- 75 Program Message Commands
- 75 Edit Program Condition
- 75 Program Control Conditions
- 76 Program Security Mode Conditions
- 76 Program Zone Conditions
- 76 Program Time Clock Conditions
- 76 Program Other Conditions
- 77 Set Up Dial
- 77 Telephone Access
- 77 Answer Outside Call
- 78 Remote Commands
- 78 Rings Before Answer
- 78 Dial Type
- 78 My Phone Number
- 78 Dial Out Number
- 79 Dial Out Numbers
- 79 Dial Order
- 79 Set Up Arming
- 79 Entry Delay
- 80 Exit Delay
- 80 Exit Time Restart
- 80 Unvacated Premises
- 80 Entry/Exit Chime
- 80 Perimeter Chime
- 80 Enable Quick Arm
- 81 Enable Auto Bypass
- 81 All On For Alarm
- 81 Beep On Trouble
- 81 Set up Miscellaneous
- 81 High Security Mode
- 81 Announce Alarms
- 82 Enable Freeze Alarm
- 82 Flash For Alarm
- 82 Console 1-8 Audible Exit Delay
- 82 House Codes 1-4 Format
- 82 House Codes 1-4 All Off
- 83 Time Clocks
- 84 Latitude, Longitude, and Time Zone
- 85 Daylight Savings
- 85 Controller IP Address
- 86 Controller Port Number
- 86 Encryption Key
- 87 Set Up Names
- 87 Set Up Voice
- 88 Set Up Address
- 89 FIRE ESCAPE PLANNING
- 93 INSTRUCTIONS TO CALLED PARTY