- No category
advertisement
Enable Auto Bypass
The Auto-Bypass feature allows the system to automatically bypass an open zone when the system is armed, rather than setting off the alarm. In some applications, it may be preferable to allow arming only if all zones are secure (READY).
With Auto-Bypass set to “No”, all zones to be armed must be secure when the system is armed. Otherwise, the console will beep three times and display "ZONE NOT RDY". If the system is armed and a zone is open when the Exit Delay expires, the alarm will sound.
The default for Enable Auto Bypass is No.
All On For Alarm
This option will instruct Omni IIe to execute an X-10 All On command in the event that any type of alarm occurs.
Beep On Trouble
If the Omni IIe detects any troubles with itself or one of the zones connected to it, it will display a message on the screen and beep the console twice per second, continuously (i.e. beep beep...beep beep...). You can silence this sound by pressing the ' * ' key.
However, if the trouble occurs again, the beeper will start beeping again.
If you do not wish to hear the beeping sound when a trouble occurs, set Beep On Trouble to No.
The default setting for Beep On Trouble is Yes.
Set up Miscellaneous
To configure Miscellaneous items in the system, from the Set Up menu, press the 6 (MISC) key.
High Security Mode
In High Security Mode, the Master or Manager code is always required to do the following functions:
•
Any Control functions
•
Any Temperature Control
•
View the Event Log
•
Access the system from a local phone
With High Security Mode Off, no code is required to access a local telephone.
If your system is set up with High Security Mode On, the display will request the Master or Manager code whenever you select one of these functions, even if the security system is Off. Simply enter your Master or Manager code.
Your system was shipped from the factory with High Security Mode Off, which allows you to view the event log and access the local phones without having to enter a code. In most residential applications, this is appropriate. If you have a commercial installation, or would like added protection from unauthorized access to the system, you may wish to turn on High Security Mode.
Announce Alarms
If the HAI Two-Way Audio Module is being used in a system, this item enables the system to speak the type of alarm and zone over a speaker on premises. When an alarm first occurs, the siren is activated. After a few seconds, the siren is turned off and the type of alarm is announced. The siren is then reactivated.
The default for Announce Alarms is No.
Page 73
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 9 Underwriter's Laboratories (UL) Listing
- 10 Console Operation
- 11 Normal Top-Level Display
- 11 Display Menus
- 12 Main Menu
- 12 Error Beeps
- 12 Trouble Beeps
- 13 Confirmation Beep
- 13 Cancel
- 13 Time Out
- 13 Areas
- 13 Omni IIe Maintenance
- 14 Disarming the Security System and Silencing Alarms
- 14 Arming the Security System
- 15 Using Shortcut Keys
- 15 Quick Arm
- 16 What Happens When You Arm the Security System
- 16 Exit Error
- 17 Bypassing Zones
- 17 Auto-Bypass
- 17 Restoring Zones
- 18 What To Do When You Come Home
- 18 What Happens When the Alarm is Activated
- 18 Burglar Alarm Activated
- 19 Fire Alarm Activated
- 19 Gas Alarm Activated
- 19 Emergency Keys
- 20 Police Emergency
- 20 Fire Emergency
- 20 Auxiliary Emergency
- 20 Duress Code Entered or Duress Alarm Activated
- 20 Alarm Reset
- 20 Alarm Cancel
- 21 Trouble Indications
- 21 Codes
- 21 Master Code
- 22 Manager Code
- 22 User Code
- 22 Duress Code
- 22 Panic Switches
- 22 Area Arming
- 23 GOTO Area
- 24 Testing Your System
- 25 Control Commands
- 25 About UPB
- 26 HAI Lighting Control (HLC) Format
- 26 About Rooms
- 26 About Room Controllers
- 26 Room Controller LED Indicators
- 27 About House Controllers
- 27 About CentraLite
- 27 About Lutron RadioRA
- 28 About ALC
- 28 ALC Module Types
- 28 About X
- 28 House Codes
- 29 Unit Numbers
- 29 Scrolling Through Names
- 29 Controlling Units
- 29 Controlling a Room of HLC Lighting
- 30 Configuring Lighting Scenes in an HLC Room
- 30 Controlling Individual Lighting Loads in an HLC Room or UPB Units
- 31 Controlling CentraLite Units
- 31 Controlling RadioRA Units
- 31 Controlling ALC or X-10 Units
- 32 Ramp Command (ALC)
- 32 Controlling Compose Units
- 33 Scene Command (Compose)
- 33 Timed Commands
- 33 Status of a Unit
- 33 Internal Flags
- 34 Controlling Outputs
- 34 All On / Off
- 35 All Lights On
- 35 All Off
- 35 Leviton Scene Control
- 35 Scene
- 36 Scene Commands
- 36 Scene Set Command
- 36 Scene On Command
- 36 Scene Off Command
- 36 UPB Links
- 37 Activating and Deactivating Links
- 37 Setting a Link (Lighting Scenes)
- 37 Executing Phantom Buttons
- 37 Executing CentraLite Scenes
- 38 Buttons
- 38 Temperature Control
- 39 HAI RC-Series Thermostats
- 40 Programmable Energy Saver Modules (PESMs)
- 42 Freeze Alarms
- 42 Indoor and Outdoor Temperature
- 43 Temperature Control of Appliances
- 43 Temperature Alarms
- 43 Humidity
- 44 Status
- 44 Configuring HLC Devices
- 44 Configuring HLC Devices using an Omni Console
- 45 Configuring HLC Devices using an OmniTouch Touchscreen
- 45 Setup Mode for HLC Devices
- 47 Event Log
- 48 Show Events
- 48 Messages
- 48 Show Message
- 49 Log Message
- 49 Clear Message
- 49 Say Message
- 49 Phone Message
- 49 Send Message (Pro-Link)
- 51 Telephone Interface
- 51 In-House Phones
- 51 Remote Phones
- 52 Phone Access Denied - Remote Lockout
- 52 Alternate Method
- 52 Main Menu
- 53 1 - Control
- 53 2 - Security
- 53 GOTO Area
- 53 3 - Button
- 53 4 - All
- 53 5 - Temperature
- 54 6 - Status
- 54 7 - Events
- 55 8 - Phone
- 55 9 - Good-Bye
- 55 Panic Button over the Phone (# # # # # #)
- 56 Emergency Dial-Out
- 56 Digital Dialer
- 56 Voice Dialer
- 56 How the Omni IIe Voice Dialer Works
- 56 What the Omni IIe Voice Dialer Does
- 57 What You Hear - If Your Omni IIe Calls You
- 57 Entering the Code
- 58 Built-In Ethernet Port
- 58 Controller IP Address, Port Number, and Encryption Key
- 58 Omni IIe Ethernet Connections
- 58 Connecting to Network via PC Access
- 59 Dynamic DNS
- 61 Configuration and Advanced Control Programming (ACP)
- 61 Set Up Codes
- 61 Authority Level
- 61 AUTHORITY
- 61 1 = Master
- 61 2 = Manager
- 61 3 = User
- 62 Access Areas
- 62 Duress Code
- 62 Set Up Time
- 63 Advanced Control Programming (ACP)
- 64 1 = Add Programs
- 64 2 = Show Programs
- 65 3 = Delete All Programs
- 65 Edit Programs
- 66 Edit Programs When
- 66 Times Programs
- 67 Button and Event Programs
- 67 Control Unit / Switch Press Event Buttons
- 68 Security Mode Event Buttons
- 69 Zone Event Buttons
- 69 All On/Off Event Buttons
- 70 UPB Link Event Buttons
- 70 Alarm Event Buttons
- 70 X-10 Event Buttons
- 71 Miscellaneous Event Buttons
- 71 Message Event Buttons (Pro-Link)
- 72 Switch Press Event Buttons (CentraLite)
- 72 Edit Program Command
- 72 Program Control Commands
- 73 Unit Toggle Command
- 73 Program Security Commands
- 74 Program Button Commands
- 74 Program All On / All Off Commands
- 74 Program Video Commands
- 74 Program Temperature Commands
- 74 Program Energy Cost
- 75 Program Message Commands
- 75 Edit Program Condition
- 75 Program Control Conditions
- 76 Program Security Mode Conditions
- 76 Program Zone Conditions
- 76 Program Time Clock Conditions
- 76 Program Other Conditions
- 77 Set Up Dial
- 77 Telephone Access
- 77 Answer Outside Call
- 78 Remote Commands
- 78 Rings Before Answer
- 78 Dial Type
- 78 My Phone Number
- 78 Dial Out Number
- 79 Dial Out Numbers
- 79 Dial Order
- 79 Set Up Arming
- 79 Entry Delay
- 80 Exit Delay
- 80 Exit Time Restart
- 80 Unvacated Premises
- 80 Entry/Exit Chime
- 80 Perimeter Chime
- 80 Enable Quick Arm
- 81 Enable Auto Bypass
- 81 All On For Alarm
- 81 Beep On Trouble
- 81 Set up Miscellaneous
- 81 High Security Mode
- 81 Announce Alarms
- 82 Enable Freeze Alarm
- 82 Flash For Alarm
- 82 Console 1-8 Audible Exit Delay
- 82 House Codes 1-4 Format
- 82 House Codes 1-4 All Off
- 83 Time Clocks
- 84 Latitude, Longitude, and Time Zone
- 85 Daylight Savings
- 85 Controller IP Address
- 86 Controller Port Number
- 86 Encryption Key
- 87 Set Up Names
- 87 Set Up Voice
- 88 Set Up Address
- 89 FIRE ESCAPE PLANNING
- 93 INSTRUCTIONS TO CALLED PARTY