advertisement
3.3. CLADDING ASSEMBLY
PELLET STOVES
INSTALLATION AND USE MANUAL
3.3.1. KAIKA STOVE
Position the steel top “A” and secure it using the four screws supplied
“D” and “E” (two on the right and two on the left) from bottom upwards.
Remove the back profile “C” already secured to the stove with three screws “F”, “G” and “H”.
Take side “B” and insert it, corresponding to the holes, into plugs “M” and “N” prearranged on the front part of the stove.
Secure side “B” using the uppers screws “L”.
At this point remount profile “C” securing it with three screws “F”, “G” and “H” to the structure and to side “B” in steel.
A
F
E
C
G
L
D
B
Chapter 3
page
21
Installation and assembly
H
Figure 4 – Assembling the sides Kaika stove
Technical service - Rights reserved MCZ GROUP S.p.A. - Reproduction prohibited
PELLET STOVES
INSTALLATION AND USE MANUAL
Chapter 3
page
22
M
D
E
N
Figure 5 – Details of Kaika stove - side and top assembly
Installation and assembly Technical service - Rights reserved MCZ GROUP S.p.A. - Reproduction prohibited
advertisement
Related manuals
advertisement
Table of contents
- 5 INTRODUCTION
- 6 1. WARNINGS AND GUARANTEE CONDITIONS
- 6 SAFETY INSTRUCTIONS
- 7 OPERATING WARNINGS
- 8 GUARANTEE CONDITIONS
- 8 Limitations
- 9 Exclusions
- 10 2. THEORETICAL NOTIONS FOR INSTALLATION
- 10 PELLETS
- 11 PRECAUTIONS FOR INSTALLATION
- 12 OPERATING AREA
- 12 CONNECTION TO THE EXTERNAL AIR INTAKE
- 13 CONNECTION OF SMOKE DISCHARGE PIPE
- 14 CONNECTION TO THE FLUE PIPE
- 14 CONNECTION TO AN EXTERNAL FLUE WITH INSULATED OR DOUBLE-WALL PIPE
- 14 CONNECTION TO THE FLUE PIPE
- 15 OPERATING PROBLEMS CAUSED BY DRAUGHT DEFECTS IN THE FLUE
- 16 3. INSTALLATION AND ASSEMBLY
- 16 DRAWINGS AND TECHNICAL CHARACTERISTICS
- 16 FACE Air
- 16 KAIKA Air
- 17 Technical characteristics
- 18 PREPARATION AND UNPACK ING
- 21 CLADDING ASSEMBLY
- 21 KAIKA STOVE
- 23 FACE STOVE
- 24 MAKING THE ELECTRICAL CONNECTIONS
- 25 4. OPERATION
- 25 PRE-LIGHTING WARNINGS
- 26 PRE-LIGHTING CHECK
- 26 LOADING THE PELLETS
- 27 CONTROL PANEL/REMOTE CONTROL DISPLAY (accessory)
- 27 Control panel logic
- 29 SETTINGS TO CARRY OUT BEFORE FIRST LIGHTING
- 29 FIRST LIGHTING
- 29 ON/OFF from the control panel or remote control (if purchased)
- 29 Note on first ignition
- 30 Power supply (panel display: ON)
- 30 OPERATING MODE
- 30 Manual mode
- 31 Automatic mode
- 31 AUTOMATIC MODE SETTING
- 31 Changing from manual to automatic mode
- 31 Cleaning the grate
- 32 HOT AIR VENTILATION
- 32 Room sensor
- 33 5. MENU STRUCTURE
- 33 The menu allows you to set/change a series of information
- 33 MAIN MENU
- 33 Setting current day and time
- 35 TIMER
- 35 TIMER activation and selection of a programme
- 36 DETAILS OF TIMER OPERATION
- 36 TIMER de-activation
- 37 SLEEP FUNCTION
- 37 Menù IMPOSTAZIONI
- 37 Setting the language
- 38 Automatic mode with AUTO-ECO (panel display: ON-AUTO ECO)
- 39 Mode AUTO-ECO
- 39 Tones (Panel display: ON-OFF)
- 39 Pellet recipe - modifying the load
- 40 Changing the smoke exhaust fan speed – Var.% smoke rpm
- 41 Connection to a room thermostat
- 42 Operating mode with external thermostat
- 43 Operating mode with external thermostat and Eco-Stop
- 44 Remote control (accessory)
- 45 General characteristics of the LCD remote control
- 45 Type of batteries and replacement
- 45 Hopper load (ON-OFF - only displayed with stove off)
- 46 Technical menu
- 46 INFO menu
- 47 6. SAFETY DEVICES
- 47 ALARM SIGNALLING
- 48 Exiting alarm condition
- 48 Normal shutdown (panel display: shutdown)
- 50 7. MAINTENANCE AND CLEANING
- 50 DAILY AND WEEKLY CLEANING BY THE USER
- 50 Before each lighting
- 50 Check every 2/3 days
- 50 Cleaning the glass
- 51 PERIODIC CLEANING BY A SPECIALISED TECHNICIAN
- 51 Cleaning of the heat exchanger
- 52 Shutting the stove down (end of season)
- 52 Check of internal components
- 53 8. PROBLEMS / CAUSES / SOLUTIONS
- 56 9. ELECTRICAL DIAGRAMS