- No category
advertisement
▼
Scroll to page 2
of
108
A.5 I/O Address Assignments
Table A-5 lists the external I/O addresses for the display and keypad I/O.
Table A-5. Display and Keypad Output Addresses
External
Address
E000–E007
E008
E00A
E00B
Name
LCD
EN
KPEN
LED
Function
LCD control
Output enable for LEDs
Read keypad and IN12
LED0–LED6 and LCD backlight
PE7 serves as a system-enable control and LCD/keypad strobe. When PE7 is high or in a high-impedance status, all OP6800 outputs are disabled (digital outputs and display outputs are disabled, and RS-485 is at listen status).
User’s Manual 55
56 MiniCom (OP6800)
advertisement
Related manuals
advertisement
Table of contents
- 5 1.1 Description
- 5 1.2 Features
- 6 1.3 Development and Evaluation Tools
- 6 1.3.1 Tool Kit
- 7 1.3.2 Software
- 8 1.4 CE Compliance
- 9 1.4.1 Design Guidelines
- 9 1.4.2 Interfacing the OP6800 to Other Devices
- 11 2.1 Connections
- 14 2.2 Demonstration Program on Power-Up
- 14 2.3 Display Contrast Adjustment
- 15 2.4 Programming Cable Connections
- 16 2.5 Installing Dynamic C
- 16 2.6 Starting Dynamic C
- 17 2.7 PONG.C
- 17 2.8 Where Do I Go From Here?
- 20 3.1 Pinouts
- 21 3.2 Digital I/O
- 21 3.2.1 Digital Inputs
- 22 3.2.2 Digital Outputs
- 23 3.3 Serial Communication
- 23 3.3.1 RS
- 23 3.3.2 RS
- 25 3.3.3 Programming Port
- 26 3.3.4 Ethernet Port (OP6800 models only)
- 27 3.4 Memory
- 27 3.4.1 SRAM
- 27 3.4.2 Flash Memory
- 28 3.5 Keypad Labeling
- 32 4.1 Programming Cable
- 32 4.1.1 Switching Between Program Mode and Run Mode
- 32 4.1.2 Detailed Instructions: Changing from Program Mode to Run Mode
- 32 4.1.3 Detailed Instructions: Changing from Run Mode to Program Mode
- 33 4.2 OP6800 Libraries
- 34 4.3 Sample Programs
- 34 4.3.1 Board ID
- 34 4.3.2 Demonstration Board
- 35 4.3.3 Digital I/O
- 35 4.3.4 Serial Communication
- 35 4.3.5 LCD/Keypad Module Sample Programs
- 36 4.3.6 TCP/IP Sample Programs
- 37 4.4 Font and Bitmap Converter
- 39 5.1 TCP/IP Connections
- 41 5.2 TCP/IP Sample Programs
- 41 5.2.1 How to Set IP Addresses in the Sample Programs
- 42 5.2.2 How to Set Up your Computer’s IP Address for a Direct Connection
- 43 5.2.3 Run the PINGME.C Demo
- 43 5.2.4 Running More Demo Programs With a Direct Connection
- 44 5.2.5 LCD/Keypad Sample Programs Showing TCP/IP Features
- 45 5.3 Where Do I Go From Here?
- 47 6.1 Installation Guidelines
- 48 6.2 Mounting Instructions
- 48 6.2.1 Bezel-Mount Installation
- 52 A.1 Electrical and Mechanical Specifications
- 55 A.2 Conformal Coating
- 56 A.3 Jumper Configurations
- 57 A.4 Use of Rabbit 2000 Parallel Ports
- 59 A.5 I/O Address Assignments
- 61 B.1 Power Supplies
- 62 B.2 Batteries and External Battery Connections
- 62 B.2.1 Battery-Backup Circuit
- 63 B.2.2 Power to VRAM Switch
- 63 B.2.3 Reset Generator
- 64 B.3 Chip Select Circuit
- 66 C.1 Mechanical Dimensions and Layout
- 67 C.2 Power Supply
- 69 C.3 Using the Demonstration Board
- 74 D.1 Board Initialization (OP68xx.LIB)
- 75 D.2 Digital I/O (OP68xx.LIB)
- 76 D.3 Serial Communication (OP68xx.LIB)
- 78 D.4 LEDs (OP68xx.LIB)
- 79 D.5 LCD Display
- 96 D.6 Keypad