advertisement
SECURITY menu
z z z
See “Navigating through the menu”
See “MAIN MENU” and “SUB MENU”
When you apply to the [SECURITY] menu before you change the password to your original, perform to input the following factory default password operation.
Press ▲►▼◄▲►▼◄ and <ENTER> button. z
Attention
When you apply to the SECURITY menu after you change the password to your original in the [SECURITY
PASSWORD CHANGE] menu, input the original password operation.
z
Note
Only asterisks * will appear on the screen to represent the actual characters of the password when the password is entered.
SECURITY PASSWORD
The [SECURITY PASSWORD] screen can be displayed when the power has been turned on. If the correct password is not entered, operations other than using <STANDBY ( )> button and <SHUTTER> button and adjusting the lens will not be possible.
1 )
2 )
Press ▲▼ to select [SECURITY
PASSWORD].
Press ◄► to switch [SECURITY
PASSWORD].
z
The setting will change as follows each time
◄► is pressed.
OFF ON
OFF
ON
Deactive
Active z z z
Note
[PASSWORD] is set to [OFF] by default and when initialized.
Change the SECURITY PASSWORD regularly and make it uneasy to guess.
The security password becomes valid when setting of the security password is turned [ON] and then the MAIN
POWER switch is turned off.
SECURITY PASSWORD
CHANGE
The password can be changed.
1 )
2 )
Press ▲▼ to select [SECURITY
PASSWORD CHANGE].
Press <ENTER> button.
z
The [SECURITY PASSWORD CHANGE] screen will be displayed.
3 ) Press ▲▼◄► and numeral keys to set the password.
z
Up to 8 buttons can be set as the password.
4 )
5 )
6 )
Press <ENTER> button.
For the purposes of confirmation, enter the password again.
Press <ENTER> button.
z z z
Note
Only asterisks * will appear on the screen to represent the actual characters of the password when the password is entered.
If the password input second does not match with the password input first, an error message is displayed. In this case, input the correct password again.
When numerals are used in the SECURITY PASSWORD, initialization of the security password will be necessary if the remote control is lost. For the method of initialization, consult your dealer.
ENGLISH -
91
SECURITY menu
DISPLAY SETTING
You can set your original text, such as company name or URL information, to display regularly on the projected image while projecting.
1 )
2 )
Press ▲▼ to select [DISPLAY
SETTING].
Press ◄► to switch [DISPLAY
SETTING].
z
The setting will change as follows each time
◄► is pressed.
OFF TEXT LOGO1
OFF
TEXT
LOGO1
The text display is disabled.
The text display is enabled.
The picture registered by the user will be projected.
z
Note
Separate software [Logo Transfer Software] is required in order to create the pictures to use for [LOGO1]. Consult your dealer.
TEXT CHANGE
You can enter your original text to be displayed when
[DISPLAY SETTING] is turned [TEXT].
1 )
2 )
Press ▲▼ to select [TEXT CHANGE].
Press <ENTER> button.
z
The [TEXT CHANGE] screen will be displayed.
3 )
4 )
Press ▲▼◄► to select characters and press <ENTER> button to input them.
Press ▲▼◄► to select [OK], and press <ENTER> button.
z
The text is now changed.
MENU LOCK
You can lock <MENU> button function and the password will be asked to display the menu every time.
1 )
2 )
Press ▲▼ to select [MENU LOCK].
Press ◄► to switch [MENU LOCK].
z
The setting will change as follows each time
◄► is pressed.
OFF ON
OFF
ON
Deactivate the [MENU LOCK] system.
Activate the [MENU LOCK] system.
z z z
Note
Once [MENU LOCK] is set to [ON], you cannot use
<MENU> button unless you input the correct password.
The [MENU LOCK] is set to [OFF] by default and when initialized.
The unlock state is maintained until the projector is set to the standby mode.
MENU LOCK PASSWORD
You can change the password for [MENU LOCK] system to your original.
1 )
2 )
Press ▲▼ to select [MENU LOCK
PASSWORD].
Press <ENTER> button.
z
The [MENU LOCK PASSWORD] screen will be displayed.
3 )
4 )
Press ▲▼◄► to select characters and press <ENTER> button to input them.
Press ▲▼◄► to select [OK], and press <ENTER> button.
z
To stop, select [CANCEL].
z z z
Attention
The factory default password is “AAAA”.
When the projector is initialized, the password will be changed to the factory default setting, “AAAA”.
Change the MENU LOCK PASSWORD regularly and make it uneasy to guess.
92
- ENGLISH
CONTROL DEVICE SETUP
Control from the remote control and main unit controls can be restricted.
1 )
2 )
Press ▲▼ to select [CONTROL
DEVICE SETUP].
Press <ENTER> button.
z
The [CONTROL DEVICE SETUP] screen will be displayed.
3 )
4 )
Press ▲▼ to select [CONTROL
PANEL] or [REMOTE CONTROLLER].
Press <ENTER> button.
z
[ CONTROL PANEL] screen or [REMOTE
CONTROLLER] screen will be displayed.
J
CONTROL PANEL
z
Restriction of control from the main unit controls can be set.
ENABLE
DISABLE
Enables control from the main unit controls.
Disables control from the main unit controls.
J
REMOTE CONTROLLER
z
Restriction of control from the remote control can be set.
ENABLE
DISABLE
Enables control from the remote control.
Disables control from the remote control.
5 ) Press ▲▼ to select [ENABLE] or
[DISABLE], and press <ENTER> button.
z
The confirmation screen will be displayed.
6 ) Press ◄► to select [OK], and press
<ENTER> button.
z z z z
Note
If an attempt is made to control the projector from the remote control or main unit controls when [DISABLE] is set, the [SECURITY PASSWORD] screen appears.
To change a setting, enter the security password and change the operation setting.
The [SECURITY PASSWORD] screen disappears if
<MENU> button is pressed or no operation is performed for 10 seconds.
If you [DISABLE] both of the [CONTROL PANEL] and
[REMOTE CONTROLLER] buttons, you cannot return to the standby mode. Use this function with utmost care.
If a setting is reflected, the on-screen menu disappears.
To continue operation, press <MENU> button to display the main menu.
SECURITY menu
ENGLISH -
93
advertisement
Related manuals
advertisement