Printer Specications

Printer Specications

Specications

Important

•

This information is subject to change as the printer is updated.

•

The following values may vary depending on the operating environment.

Printer

Power supply

Power consumption

Operating noise

Operating environment

Dimensions (W × D

× H)

In operation

Sleep mode

Off

Temperature

Humidity

Printer only

With stand

Printer only

With stand

100-120 V AC (50/60 Hz), 220-240 V AC (50/60 Hz)

100 W max.

100-120 V: 5 W max.

(8 W max. when an IEEE 1394 (FireWire) expansion board is installed.)

220-240 V: 6 W max.

(9 W max. when an IEEE 1394 (FireWire) expansion board is installed.)

1 W max. (*1)

Approx. 49 dB (A) max.

15-30°C (59-86°F)

10-80%, non-condensing

1,177×670×348 mm (46.3 × 26.4 × 13.7 in)

1,177×861×993 mm (46.3 × 33.9× 39.1 in)

-

51 kg (112.4 lb) Weight

(not including the

Printhead and Ink

Tank )

Space required for installation (*2)

Applicable standards

Printer only

With stand

1,477×1,770×648 mm (58.1 × 80.7 × 25.5 in)

1,477×1,770×1,294 mm (58.1 × 80.7 × 50.9 in)

International Energy Star Program, Law on Promoting Green

Purchasing, GPN, RoHS, The Eco Declaration, WEEE, U.S.

presidential directives

*1: The printer uses a trace amount of power even when turned off. To stop all power consumption, turn off the printer and unplug the power cord.

*2: Normally, you will need to ensure an unobstructed space of 800 mm (31.5 in) in front of the printer, 300 mm (11.8 in) behind, 150 mm (5.9 in) on both sides, and 300 mm (11.8 in) above the printer. Only when printing from the Front Paper Feed Slot, leave 1,300 mm (51.2 in) of unobstructed space in front of the printer and 700 mm (27.6 in) behind it.

72 Printer Parts

Downloaded from ManualsPrinter.com Manuals

Printer Specications

Printing performance

Print method

Maximum resolution

Printhead

Number of nozzles

Bubblejet

2400 dpi horizontally (*1) × 1200 dpi vertically

PF-03

2,560 per color

*1: Prints with a minimum 1/2400 inch dot pitch between ink droplets.

Interface

Expansion Board Slots

USB 2.0(*1)

Ethernet (*3)

IEEE 1394 (*2)

Format

Mode

Connector

Format

Specication

Protocols

Format

Specication

1

Internal port

Full-speed (12 Mbps), high-speed (480 Mbps), bulk transfer

Series B (4-pin)

Internal port

IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX

/Auto-Negotiation, and IEEE 802.3x Full Duplex

IPX/SPX (Netware 4.2, 5.1, 6.0), SNMP, HTTP, TCP/IP,

AppleTalk

Optional boards (slot type)

IEEE 1394-1995, conforms to P1394a Specication ver. 2.0, half duplex, Data/Strb differential serial

100/200/400 Mbps

Conforms to IEEE 1394-1995 (6-pin), no power supply

Transfer speed

Connector

*1: Use in USB 2.0 High Speed mode requires the following environment:

•

Computer: USB 2.0 High-Speed-compatible

•

Operating system: Windows

Vista/Windows Server 2003/Windows XP/Windows 2000 or Mac OS X ver. 10.3.3

or later

•

USB 2.0 driver: Microsoft

USB 2.0 driver (available from Windows Update or the Service Pack.)

•

USB cable: Certied

USB 2.0 cable

*2: One IEEE 1394 (FireWire) expansion board can be installed.

*3: In the European Union, use a shielded LAN cable to comply with EN 55022: 1998 +A1: 2000 and

A2: 2003.

Printer Parts 73

Downloaded from ManualsPrinter.com Manuals

Printer Specications

Ink

Ink Tank

Capacity

Y Ink Tank ( Yellow Ink )

PC Ink Tank ( Photo Cyan

Ink )

B Ink Tank ( Blue Ink )

Pigment ink

Pigment ink

PFI-101Y (user-replaceable)

PFI-101PC (user-replaceable)

C Ink Tank ( Cyan Ink ) Pigment ink PFI-101C (user-replaceable)

PGY Ink Tank ( Photo Gray

Ink )

Pigment ink PFI-103PGY (user-replaceable)

GY Ink Tank ( Gray Ink )

BK Ink Tank ( Black Ink )

Pigment ink PFI-103GY (user-replaceable)

Pigment ink PFI-103BK (user-replaceable)

PM Ink Tank ( Photo

Magenta Ink )

Pigment ink PFI-101PM (user-replaceable)

M Ink Tank ( Magenta Ink ) Pigment ink PFI-101M (user-replaceable)

MBK Ink Tank ( Matte Black

Ink , or black ink for matte paper)

Pigment ink PFI-103MBK (user-replaceable)

R Ink Tank ( Red Ink )

G Ink Tank ( Green Ink )

Pigment ink

Pigment ink

PFI-101R (user-replaceable)

PFI-101G (user-replaceable)

Pigment ink PFI-101B (user-replaceable)

130 ml per color (*1)

*1: Printable pages when using the provided Starter Ink Tanks (90 ml per tank)

74 Printer Parts

Downloaded from ManualsPrinter.com Manuals

Printer Specications

Paper (*1)

Paper width

Maximum length per page

Thickness

Paper size

Print area

Sheets

Rolls

Sheets

Tray (top)

Tray (front)

Tray (top)

Tray (front)

Rolls

Sheets Supported sizes

Rolls

Normal size

Tray (top)

Tray (front)

Borderless printing (*2)

Oversized (*2), (*3)

Supported width for borderless printing

250-610 mm (9.8-24 in)

1,600 mm (63.0 in)

914 mm (36.0 in)

18 m (19.7 yd.)

0.08-0.8 mm (0.003-0.031 in)

0.8-1.5 mm (0.031-0.060 in)

0.08-0.8 mm (0.003-0.031 in)

ISO A1, ISO A2, ISO A2+, ISO A3, ISO A3+, ISO A4, ISO B2,

ISO B3, ISO B4, JIS B2, JIS B3, JIS B4, 22"x34" (ANSI D),

17"x22" (ANSI C), 11"x17" (Ledger), 13"x19" (SuperB), Letter

(8.5"x11"), Legal (8.5"x14"), 24"x36" (ARCH D), 18"x24"

(ARCH C), 12"x18" (ARCH B), 9"x12" (ARCH A), DIN C2,

DIN C3, DIN C4, 20"x24", 18"x22", 14"x17", 12"x16", 10"x12",

10"x15", 8"x10", US Photo 16"x20", Poster 20"x30", 13"x22",

Poster 300x900 mm

•

Width: 203-610 mm (8-24 in)

•

Length: 279-1,600 mm (11-63 in)

•

Width: 250-610 mm (8-24 in)

•

Length: 350-914 mm (14-36 in)

8 inches (203 mm), 10 inches (254 mm), JIS B4 (257 mm),

ISO A3/A4 (297 mm), Banner (300 mm), A3+ (329 mm), 14 inches (356 mm), 16 inches (407 mm), ISO A2/A3 (420 mm),

17 inches (432 mm), JIS B2/B3 (515 mm), ISO A1/A2 (594 mm), 24 inches (610 mm)

Printable area

•

Sheets ( Top Paper Feed Slot )

Top: 3 mm (0.12 in); bottom: 3 or 23 mm (0.9 in); left and right sides: 3 mm. (The bottom value varies depending on the type of paper.)

•

Sheets ( Front Paper Feed Slot )

3 mm (0.12 in) on top, 23 mm (0.9 in) on bottom, and 3 mm (0.12 in) on both sides

•

Rolls

3 mm (0.12 in) from each side

For information on the recommended print area, see “Print

Area”. (→P.78)

Printable area (rolls)

Entire surface

Printable area

Entire surface

10 inches (254 mm), JIS B4 (257 mm), A3+ (329 mm), 14 inches (356 mm), 16 inches (407 mm), ISO A2/A3 (420 mm)

(*4), 17 inches (432 mm), JIS B2/B3 (515 mm), ISO A1/A2

(594 mm) (*4), 24 inches (610 mm)

Printer Parts 75

Downloaded from ManualsPrinter.com Manuals

Printer Specications

*1: For information on the types of paper the printer supports, refer to the Paper Reference Guide.

(→P.108)

*2: Printing may not be possible in some cases, depending on the type and size of paper.

*3: Load paper at least 6 mm (0.24 in) wider and 6 mm higher than the size selected in Page Size for roll paper. Or, load paper at least 6 mm wider and 26 mm (1.0 in) higher for the tray.

*4: Borderless printing requires the Spacer for Borderless Printing.

76 Printer Parts

Downloaded from ManualsPrinter.com Manuals

Printer Specications

Basic Environmental Performance

Printer

Power consumption

Resource efciency

Product safety

Sleep mode

Operating noise

100-120 V: 5 W max.

(8 W max. when an IEEE 1394 (FireWire) expansion board is installed.)

220-240 V: 6 W max.

(9 W max. when an IEEE 1394 (FireWire) expansion board is installed.)

1 W max.

Printer only: 51 kg (112.4 lb)

Off

Weight

Dimensions (W × D ×

H)

Printer only: 1,177×670×348 mm (46.3 × 26.4 × 13.7 in)

Recycling Recyclable plastic used for printer body

Toxic substances Structural components: No prohibited brominated ame retardants used (PBB or PBDE)

Body plastic: No heavy metals (Pb, Hg, Cr[Vl], or Cd) or halogenated ame retardants used

Approx. 49 dB (A) max.

Packaging materials

Heavy metal content (Pb, Hg, Cr[Vl], and Cd) None (none in packaging)

Downloaded from ManualsPrinter.com Manuals

Printer Parts 77

Printer Specications

Print Area

A margin required by the printer is added with respect to the size of paper loaded in the printer. Except in borderless printing, the actual printing area corresponds to the paper size minus the space for this margin.

Sheets

Top Paper

Feed Slot

Top Edge

3 mm (0.12

in)

Printable Area

Bottom

Edge

3/23 mm

(0.12/0.91

in)

Sides

3 mm (0.12

in)

Recommended Print Area

Top Edge

Bottom

Edge

Sides

20 mm (0.79

in)

27 mm (1.06

in)

5 mm (0.20

in)

Front Paper

Feed Slot

3 mm (0.12

in)

23 mm (0.91

in)

3 mm (0.12

in)

Rolls

0/3 mm

(0/0.12 in)

0/3 mm

(0/0.12 in)

0/3 mm

(0/0.12 in)

20 mm (0.79

in)

5 mm (0.20

in)

5 mm (0.20

in)

Sheets

•

Printable Area:

Printing from the Top Paper Feed Slot requires a margin of 3 mm (0.12 in) on all sides. (A bottom margin of 23 mm [0.9 in] may sometimes be required.) The bottom margin is 23 mm for some types of paper.

For more information, see the Paper Reference Guide. (→P.108)

When printing from the Front Paper Feed Slot, a margin of 23 mm (0.9 in) on all sides is required.

•

Recommended print area:

A margin of 20 mm (0.79 in) on top, 27 mm (1.06 in) on bottom, and 5 mm (0.20 in) on left and right sides is required.

Note

•

Printable area: The area that can be printed.

•

Guaranteed Print Area: We recommend printing within this area.

•

To print so that your original matches the print area exactly, use an oversized paper size that includes the required margin. (→P.277)

•

You can choose a bottom margin of 3 mm or 23 mm when printing from the Top Paper Feed Slot.

In the printer driver, choosing Manual in Media Source sets the bottom margin at 23 mm. On the other hand, choosing Manual (3mm margins) in Media Source sets the bottom margin at 3 mm, which provides a larger area for printing.

However, the option Manual (3mm margins) is not available with the following paper.

•

Fine Art Photo Paper

•

Fine Art Heavyweight Photo Paper

•

Fine Art Textured Paper

•

The types of paper listed above may be updated, in some cases.

For details on paper types, see the Paper Reference Guide. (→P.108)

•

If you set the bottom margin at 3 mm, images in the bottom margin may be distorted.

In this case, choose Manual in Media Source to set the bottom margin at 23 mm.

78 Printer Parts

Downloaded from ManualsPrinter.com Manuals

Printer Specications

Rolls

•

Printable Area:

A margin of 3 mm (0.12 in) on all sides is required. During borderless printing, the margin on all sides is 0 mm. For information on paper compatible with borderless printing, see the Paper Reference

Guide. (→P.108)

•

Recommended print area:

A margin of 20 mm (0.79 in) on top, 5 mm (0.20 in) on bottom, and 5 mm (0.20 in) on left and right sides is required.

Note

•

Printable area: The area that can be printed.

•

Guaranteed Print Area: We recommend printing within this area.

•

To print so that your original matches the print area exactly, use an oversized paper size that includes the required margin. (→P.277)

Downloaded from ManualsPrinter.com Manuals

Printer Parts 79