advertisement
Using external equipment
Setting the recording mode (i.LINK)
• The function for automatically adjusting the recording mode of connected D-VHS decks can be turned on or off.
• Since most of the currently available D-VHS decks automatically recognize the transfer rates of the pictures and sound being recorded and control the recording mode accordingly, you should always set
this Mode to “Pass thru” in normal circumstances.
• Depending on the D-VHS deck used and the type of broadcast being recorded, this TV may not adjust the recording mode properly. In this case, please set the “Recording Mode” to “Pass thru”.
Setting the Standby Mode (i.LINK)
• Power consumption during standby mode can be minimized by changing the setting of the “Standby
Mode” in “i.LINK Setup”.
• When i.LINK is not in use, select “Inactive” in
“Standby Mode”.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Digital Setup”.
1
Press MENU and the MENU screen displays.
3
Press a/b to select “i.LINK Setup”, and then press ENTER.
2
Press c/d to select “Digital Setup”.
4
Press a/b to select “Standby Mode”, and then press ENTER.
3
Press a/b to select “i.LINK Setup”, and then press ENTER.
4
5
Press a/b to select “Recording Mode”, and then press ENTER.
Press c/d to select “Auto” or “Pass thru”, and then press ENTER.
• Normally, this should be set to “Pass thru”.
5
Press c/d to select “Active” or “Inactive”, and then press ENTER.
“Active”: Power continues to pass through the i.LINK
circuit so data can be relayed.
“Inactive”: Power consumption is minimized during stand-by mode. Data cannot be relayed at this setting.
NOTE
• When the main power of the TV is in standby mode
(POWER indicator lights off), i.LINK control commands cannot be received from a D-VHS deck. This does not change even if the “Standby Mode” is set to “Active”. To control the TV from a D-VHS deck, turn the TV power on
(POWER indicator lights up in blue).
• Data cannot be relayed between i.LINK devices when all the following conditions are met: 1) More than one i.LINK
device is connected to the TV with i.LINK cables, 2)
“Standby Mode” is set to “Inactive”, and 3) The power of the TV is in standby mode (POWER indicator lights off).
When the TV is connected between two i.LINK devices in series, select “Active” in “Standby Mode” or connect the
TV at an end of the series as shown in the diagram.
57
advertisement
Related manuals
advertisement
Table of contents
- 2 IMPORTANT INFORMATION
- 4 DEAR SHARP CUSTOMER
- 4 IMPORTANT SAFETY INSTRUCTIONS
- 7 Contents
- 8 Trademarks
- 8 Patent Notice
- 9 Supplied accessories
- 10 Preparation
- 10 Where to place the TV
- 12 Removing speakers
- 13 Removing the stand
- 13 Setting the Display on the wall
- 14 Inserting the batteries
- 14 Using the remote control unit
- 15 Part names
- 17 Remote control unit
- 18 Cable TV/VCR connection
- 20 Outdoor antenna connection
- 21 Turning on the power
- 21 Turning off the power
- 22 Initial setup
- 23 Changing channels Analog-TV
- 24 Changing volume/sound
- 25 Setting MTS/SAP stereo mode
- 26 Connecting Digital Cable Module
- 27 Basic adjustment settings
- 27 AV input mode menu items
- 28 PC input mode menu items
- 28 EZ setup
- 29 Channel setup
- 31 Antenna Setup-DIGITAL
- 32 Favorite channel setting
- 32 Language setting
- 33 Picture adjustments
- 34 OPC setting
- 35 Color temperature
- 35 3D-Y/C
- 36 Monochrome
- 37 Sound adjustment
- 37 Dolby virtual
- 38 Power control
- 38 Power control for AV source
- 38 Power control for PC source
- 39 Digital Setup
- 39 Video Setup
- 41 Using memory card
- 45 Displaying slide show
- 46 My Program
- 46 Audio Select
- 47 Deleting a still image file
- 47 Deleting all still image files
- 48 Recording a motion picture
- 48 Rec. Mode
- 49 Pre Record
- 49 Repeat Play
- 50 Deleting a motion picture file
- 50 Deleting all motion picture files
- 50 Format
- 51 Using external equipment
- 52 Connecting a DVD player
- 53 or camcorder
- 54 Connecting a Digital TV STB
- 55 Connecting HDMI equipment
- 55 equipment
- 56 Connecting a PC
- 57 i.LINK connection
- 58 Setting the recording mode
- 59 Selecting a D-VHS deck (i.LINK)
- 59 a D-VHS deck (i.LINK)
- 60 Controlling an i.LINK device
- 62 with a D-VHS deck (i.LINK)
- 63 Useful adjustment settings
- 63 Moving the picture on the screen
- 64 Connecting external speakers
- 65 Audio Quality Control
- 68 Input label
- 68 Picture Flip
- 69 AV MODE
- 69 View mode for 4:3 Programs
- 70 View mode (for PC input mode)
- 71 Digital Noise Reduction
- 71 Audio only
- 72 Output Select
- 72 Sleep timer
- 73 Title Display Type
- 74 Closed caption
- 75 Font Style
- 76 Foreground Color
- 76 Foreground Opacity
- 76 Background Color
- 77 Background Opacity
- 77 Character Edge
- 78 (AV input mode only)
- 80 Parental control (setting V-CHIP level)
- 84 V-CHIP BLOCK
- 85 Center Channel Input
- 86 Other viewing options
- 86 Viewing information of the program
- 87 Twin picture functions
- 87 Presetting remote control function
- 93 Troubleshooting
- 94 PC compatibility chart
- 95 RS-232C port specifications
- 97 Optional accessory
- 98 Dimensional drawings