- No category
advertisement
CBX ELECTRICAL CONNECTIONS
4
4 CBX ELECTRICAL CONNECTIONS
All DS4800 models are equipped with a cable terminated by a 25-pin male D-sub connector for connection to the power supply and input/output signals.
We recommend making system connections through one of the CBX connection boxes since they offer the advantages of easy connection, easy device replacement and filtered reference signals.
NOTE
If you require direct wiring to the scanner the details of the connector pins
and relative connections are indicated in Chaper 5.
The table below gives the pinout of the CBX100/500 terminal block connectors. Use this pinout when the DS4800 reader is connected by means of the CBX100/500:
CBX100/500 Terminal Block Connectors
Vdc
GND
Earth
+V
-V
O1+
O1-
O2+
O2-
+V
I1A
I1B
-V
+V
I2A
I2B
-V
TX
RX
SGND
Input Power
Power Supply Input Voltage +
Power Supply Input Voltage -
Protection Earth Ground
Inputs
Power Source – External Trigger
External Trigger A (polarity insensitive)
External Trigger B (polarity insensitive)
Power Reference – External Trigger
Power Source – Inputs
Input 2 A (polarity insensitive)
Input 2 B (polarity insensitive)
Power Reference – Inputs
Outputs
Power Source - Outputs
Power Reference - Outputs
Output 1 +
Output 1 -
Output 2 +
Output 2 -
Auxiliary Interface
Auxiliary Interface TX
Auxiliary Interface RX
Auxiliary Interface Reference
ID-NET™
ID+
ID-
Shield
ID-NET™ network +
ID-NET™ network -
Network Cable Shield
Main Interface
RS232
TX
RX
RTS
CTS
SGND
RS485
Full-Duplex
RS485
Half-Duplex
TX+ RTX+
*RX+
TX-
*RX-
RTX-
SGND SGND
* Do not leave floating, see par. 4.2.2 for connection details.
41
advertisement
Related manuals
advertisement
Table of contents
- 13 RAPID CONFIGURATION
- 13 Step 1 – Connect the System
- 16 Step 2 – Mount and Position the Scanner
- 17 Step 3 – Focus the Scanner
- 18 Step 4 – X-PRESS™ Configuration
- 22 Step 5 – Install Genius™ Configuration Program
- 27 Step 6 – Test Mode
- 28 Advanced Scanner Configuration
- 30 INTRODUCTION
- 30 Product Description
- 31 Indicators
- 31 ID-NET
- 33 How To Setup/Configure the Scanner Network
- 34 X-PRESS™ Human Machine Interface
- 34 Diagnostic Indication
- 35 X-PRESS™ Functions
- 37 Display
- 38 Display Messages
- 41 Oscillating Mirror Models
- 42 Subzero Temperature Models
- 43 Model Description
- 43 Accessories
- 44 INSTALLATION
- 44 Package Contents
- 45 Mechanical Installation
- 48 Mounting DS
- 51 Positioning
- 53 CBX ELECTRICAL CONNECTIONS
- 54 Power Supply
- 54 Main Serial Interface
- 55 RS232 Interface
- 56 RS485 Full-Duplex Interface
- 57 RS485 Half-Duplex Interface
- 59 ID-NET™ Interface
- 59 ID-NET™ Cables
- 60 ID-NET™ Response Time
- 64 ID-NET™ Network Termination
- 64 Auxiliary RS232 Interface
- 65 Inputs
- 68 Code Verifier
- 68 Outputs
- 70 User Interface - Host
- 71 25-PIN CABLE ELECTRICAL CONNECTIONS
- 72 Power Supply
- 72 Main Serial Interface
- 73 RS232 Interface
- 74 RS485 Full-Duplex Interface
- 75 RS485 Half-Duplex Interface
- 77 ID-NET™ Interface
- 77 ID-NET™ Cables
- 78 ID-NET™ Response Time
- 82 ID-NET™ Network Termination
- 82 Auxiliary RS232 Interface
- 83 Inputs
- 86 Code Verifier
- 86 Outputs
- 87 User Interface - Host
- 88 TYPICAL LAYOUTS
- 88 Point-to-Point
- 90 Pass-Through
- 92 ID-NET
- 95 RS232 Master/Slave
- 96 Multiplexer Layout
- 97 READING FEATURES
- 97 Advanced Code Reconstruction (ACR™ 4)
- 98 Tilt Angle for Advanced Code Reconstruction
- 99 Advanced Code Reconstruction Reading Conditions
- 101 Linear Code Reading
- 101 Step-Ladder Mode
- 102 Picket-Fence Mode
- 103 Performance
- 104 Reading Diagrams
- 104 X0XX Standard Models
- 107 X1XX Oscillating Mirror Models
- 110 XXX5 Subzero Models
- 113 MAINTENANCE
- 113 Cleaning
- 114 TROUBLESHOOTING
- 114 General Guidelines
- 117 TECHNICAL FEATURES
- 119 GLOSSARY
- 122 INDEX