- No category
advertisement
25-PIN CABLE ELECTRICAL CONNECTIONS
5
5.5 INPUTS
There are two optocoupled polarity insensitive inputs available on the scanner: Input 1
(External Trigger) and Input 2, a generic input:
The electrical features of both inputs are:
Maximum voltage: 30 Vdc
Maximum current: 12 mA
An anti-disturbance filter is implemented in software on both inputs so that the minimum pulse duration is
5 milliseconds. This value can be increased through the software parameter Debounce Filter, see the "2K/4K Family Software Configuration Parameter Guide”
Help file".
25-pin
9
Name
Vdc
Function
Power Source - External Trigger
18
19
I1A
I1B
External Trigger A (polarity insensitive)
External Trigger B (polarity insensitive)
7 GND Power Reference - External Trigger
The External Trigger input is used in the On-Line operating Mode and tells the scanner to scan for a code. The active state of this input is selected in software. Refer to the Genius™
Help On Line.
The yellow Trigger LED (
, 3) is on when the active state of the External Trigger corresponds to ON.
This input is optocoupled and can be driven by both an NPN and PNP type command. The connections are indicated in the following diagrams:
EXTERNAL TRIGGER INPUT PNP PH-1
DS4800
PNP PH-1 wires
9
Vdc
(brown) +10-30 Vdc
18
I1A
(black) NO
V
CC
+
~
~
-
19
I1B
7
GND
(blue) 0 V
Figure 58 - PH-1 Photocell (PNP) External Trigger Using DS4800 Power
71
DS4800 REFERENCE MANUAL
5
EXTERNAL TRIGGER INPUT CONNECTIONS USING DS4800 POWER
DS4800
9
Vdc
I1A
EXTERNAL TRIGGER
V
Signal
18
V
CC
+
~
~
-
19
I1B
7
GND
Ground
Figure 59 - PNP External Trigger Using DS4800 Power
DS4800 EXTERNAL TRIGGER
9
Vdc
V
18
I1A
V
CC
+
~
~
-
19
I1B
GND
Signal
7
Ground
Figure 60 - NPN External Trigger using DS4800 power
EXTERNAL TRIGGER INPUT CONNECTIONS USING EXTERNAL POWER
DS4800
V
CC
~
+
-
~
18
19
Vext 30 Vdc max.
EXTERNAL TRIGGER
V
I1A
Signal
I1B
Figure 61 - PNP External Trigger Using External Power
DS4800
Vext 30 Vdc max.
EXTERNAL TRIGGER
18
I1A
V
CC
I1B
V
~
+ -
~
19
Signal
Figure 62 - NPN External Trigger Using External Power
72
25-PIN CABLE ELECTRICAL CONNECTIONS
25-pin
9
6
10
7
Name
Vdc
I2A
I2B
GND
Function
Power Source Inputs
Input 2 A (polarity insensitive)
Input 2 B (polarity insensitive)
Power Reference - Inputs
INPUT 2 CONNECTIONS USING DS4800 POWER
DS4800
V
CC
+
~
~
-
9
6
10
7
GND
Vdc
I2A
I2B
INPUT DEVICE
V
Signal
Ground
Figure 63 - PNP Input 2 Using DS4800 Power
DS4800
V
CC
+
~
~
-
9
6
Vdc
I2A
10
7
I2B
GND
INPUT DEVICE
V
Ground
Signal
Figure 64 - NPN Input 2 Using DS4800 Power
INPUT 2 CONNECTIONS USING EXTERNAL POWER
DS4800
V
CC
~
+
-
~
6
10
Vext 30 Vdc max.
EXTERNAL TRIGGER
V
I2A
Signal
I2B
Figure 65 - PNP Input 2 Using External Power
DS4800
V
CC
~
+
-
~
6
10
Vext 30 Vdc max.
EXTERNAL TRIGGER
I2A
I2B
V
Signal
Figure 66 - NPN Input 2 Using External Power
5
73
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 13 RAPID CONFIGURATION
- 13 Step 1 – Connect the System
- 16 Step 2 – Mount and Position the Scanner
- 17 Step 3 – Focus the Scanner
- 18 Step 4 – X-PRESS™ Configuration
- 22 Step 5 – Install Genius™ Configuration Program
- 27 Step 6 – Test Mode
- 28 Advanced Scanner Configuration
- 30 INTRODUCTION
- 30 Product Description
- 31 Indicators
- 31 ID-NET
- 33 How To Setup/Configure the Scanner Network
- 34 X-PRESS™ Human Machine Interface
- 34 Diagnostic Indication
- 35 X-PRESS™ Functions
- 37 Display
- 38 Display Messages
- 41 Oscillating Mirror Models
- 42 Subzero Temperature Models
- 43 Model Description
- 43 Accessories
- 44 INSTALLATION
- 44 Package Contents
- 45 Mechanical Installation
- 48 Mounting DS
- 51 Positioning
- 53 CBX ELECTRICAL CONNECTIONS
- 54 Power Supply
- 54 Main Serial Interface
- 55 RS232 Interface
- 56 RS485 Full-Duplex Interface
- 57 RS485 Half-Duplex Interface
- 59 ID-NET™ Interface
- 59 ID-NET™ Cables
- 60 ID-NET™ Response Time
- 64 ID-NET™ Network Termination
- 64 Auxiliary RS232 Interface
- 65 Inputs
- 68 Code Verifier
- 68 Outputs
- 70 User Interface - Host
- 71 25-PIN CABLE ELECTRICAL CONNECTIONS
- 72 Power Supply
- 72 Main Serial Interface
- 73 RS232 Interface
- 74 RS485 Full-Duplex Interface
- 75 RS485 Half-Duplex Interface
- 77 ID-NET™ Interface
- 77 ID-NET™ Cables
- 78 ID-NET™ Response Time
- 82 ID-NET™ Network Termination
- 82 Auxiliary RS232 Interface
- 83 Inputs
- 86 Code Verifier
- 86 Outputs
- 87 User Interface - Host
- 88 TYPICAL LAYOUTS
- 88 Point-to-Point
- 90 Pass-Through
- 92 ID-NET
- 95 RS232 Master/Slave
- 96 Multiplexer Layout
- 97 READING FEATURES
- 97 Advanced Code Reconstruction (ACR™ 4)
- 98 Tilt Angle for Advanced Code Reconstruction
- 99 Advanced Code Reconstruction Reading Conditions
- 101 Linear Code Reading
- 101 Step-Ladder Mode
- 102 Picket-Fence Mode
- 103 Performance
- 104 Reading Diagrams
- 104 X0XX Standard Models
- 107 X1XX Oscillating Mirror Models
- 110 XXX5 Subzero Models
- 113 MAINTENANCE
- 113 Cleaning
- 114 TROUBLESHOOTING
- 114 General Guidelines
- 117 TECHNICAL FEATURES
- 119 GLOSSARY
- 122 INDEX