- No category
advertisement
READING FEATURES
7.4.2 X1XX Oscillating Mirror Models
DS4800-X1XX
Focus Distance 30 cm (Near)
0 15
0 10 20 30 40 50 60 70 80
20
50
35 40
(in)
90 100
15
40
10
30
20
5
10
0 0
0.50 mm
(20 mils)
10
5
20
10
30
15
40
0.20 mm
(8 mils)
0.30 mm
(12 mils)
0.38 mm
(15 mils)
20
50
(in)
(cm)
NOTE: (0,0) is the center of the laser beam output window.
CONDITIONS
Code =
"Pitch" angle
"Skew" angle
"Tilt" angle
= 0
= 15
= 0
to 30
= 800 scans/sec. *Scan Speed
*Reading Condition
* Reading Mode
= Standard
= Linear
Parameter selectable in Genius™
For Tilt angles of 45°, the reading performance is reduced by approximately the following values:
Minimum reading distance: +20%
Maximum reading distance: -30%
Maximum reading width: -15%
7
95
DS4800 REFERENCE MANUAL
7
20
50
0
0
DS4800-X1XX
Focus Distance 40 cm (Medium)
10 20 30
15
40 50 60 70
15
40
10
30
20
5
10
0 0
10
5
20
10
30
15
40
0.30 mm
(12 mils)
0.50 mm
(20 mils)
0.38 mm
(15 mils)
20
50
(in)
(cm)
NOTE: (0,0) is the center of the laser beam output window.
CONDITIONS
80
35 40
(in)
90 100
"Pitch" angle
"Skew" angle
"Tilt" angle
*Scan Speed
*Reading Condition
= 0
= 15
= 0 to 30
= 800 scans/sec.
= Standard
* Reading Mode = Linear
* Parameter selectable in Genius™
For Tilt angles of 45°, the reading performance is reduced by approximately the following values:
Minimum reading distance: +20%
Maximum reading distance: -25%
Maximum reading width: -15%
96
READING FEATURES
DS4800-X1XX
Focus Distance 60 cm (Far)
60
20
50
0 15 35 40 45
(in)
0 10 20 30 40 50 60 70 80 90 100 110 120
15
40
30
10
20
5
10
0 0
5
10
20
10
30
15
40
0.38 mm
(15 mils)
0.50 mm
(20 mils)
20
50
(in)
60
(cm)
NOTE: (0,0) is the center of the laser beam output window.
CONDITIONS
"Pitch" angle
0.90
= 0
"Skew" angle
"Tilt" angle
= 15
= 0 to 30
*Scan Speed
*Reading Condition
= 800 scans/sec.
= Standard
* Reading Mode = Linear
* Parameter selectable in Genius™
For Tilt angles of 45°, the reading performance is reduced by approximately the following values:
Minimum reading distance: +20%
Maximum reading distance: -15%
Maximum reading width: -15%
7
97
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 13 RAPID CONFIGURATION
- 13 Step 1 – Connect the System
- 16 Step 2 – Mount and Position the Scanner
- 17 Step 3 – Focus the Scanner
- 18 Step 4 – X-PRESS™ Configuration
- 22 Step 5 – Install Genius™ Configuration Program
- 27 Step 6 – Test Mode
- 28 Advanced Scanner Configuration
- 30 INTRODUCTION
- 30 Product Description
- 31 Indicators
- 31 ID-NET
- 33 How To Setup/Configure the Scanner Network
- 34 X-PRESS™ Human Machine Interface
- 34 Diagnostic Indication
- 35 X-PRESS™ Functions
- 37 Display
- 38 Display Messages
- 41 Oscillating Mirror Models
- 42 Subzero Temperature Models
- 43 Model Description
- 43 Accessories
- 44 INSTALLATION
- 44 Package Contents
- 45 Mechanical Installation
- 48 Mounting DS
- 51 Positioning
- 53 CBX ELECTRICAL CONNECTIONS
- 54 Power Supply
- 54 Main Serial Interface
- 55 RS232 Interface
- 56 RS485 Full-Duplex Interface
- 57 RS485 Half-Duplex Interface
- 59 ID-NET™ Interface
- 59 ID-NET™ Cables
- 60 ID-NET™ Response Time
- 64 ID-NET™ Network Termination
- 64 Auxiliary RS232 Interface
- 65 Inputs
- 68 Code Verifier
- 68 Outputs
- 70 User Interface - Host
- 71 25-PIN CABLE ELECTRICAL CONNECTIONS
- 72 Power Supply
- 72 Main Serial Interface
- 73 RS232 Interface
- 74 RS485 Full-Duplex Interface
- 75 RS485 Half-Duplex Interface
- 77 ID-NET™ Interface
- 77 ID-NET™ Cables
- 78 ID-NET™ Response Time
- 82 ID-NET™ Network Termination
- 82 Auxiliary RS232 Interface
- 83 Inputs
- 86 Code Verifier
- 86 Outputs
- 87 User Interface - Host
- 88 TYPICAL LAYOUTS
- 88 Point-to-Point
- 90 Pass-Through
- 92 ID-NET
- 95 RS232 Master/Slave
- 96 Multiplexer Layout
- 97 READING FEATURES
- 97 Advanced Code Reconstruction (ACR™ 4)
- 98 Tilt Angle for Advanced Code Reconstruction
- 99 Advanced Code Reconstruction Reading Conditions
- 101 Linear Code Reading
- 101 Step-Ladder Mode
- 102 Picket-Fence Mode
- 103 Performance
- 104 Reading Diagrams
- 104 X0XX Standard Models
- 107 X1XX Oscillating Mirror Models
- 110 XXX5 Subzero Models
- 113 MAINTENANCE
- 113 Cleaning
- 114 TROUBLESHOOTING
- 114 General Guidelines
- 117 TECHNICAL FEATURES
- 119 GLOSSARY
- 122 INDEX