HiCommand® Device Manager Error Codes

Hitachi Device Manager Messages

This chapter describes the error messages for the Hitachi Device Manager server, Web Client, Agent, VDS Provider, CLI, and CLIEX.



Device Manager Server Messages



Device Manager Web Client Messages



Device Manager Agent Messages



Device Manager Agent's Provisioning Manager Messages



Device Manager Agent's Replication Manager Messages



Device Manager VDS Provider Messages



Device Manager CLI Messages



Device Manager CLIEX Messages

Hitachi Device Manager Messages

Hitachi Device Manager Error Codes

1-1

Device Manager Server Messages

Hitachi Device Manager displays error messages when errors occur. All error notifications, including Server errors, are displayed at the Hitachi Device

Manager client (e.g., Web Client, CLI, third-party application). The error message includes:



Error code: The error code range indicates the type of error (see Table 1-

1). The error code indicates the specific error condition.



Error level: The error level indicates the severity of the error:

I: Non-error information

W: Warning

E: Error



Description: The error description provides information on the error condition.

Table 1-1 Server Error Code Ranges

Error Code Range

KAIC00000-KAIC00999

Description

Device Manager Server (SRV) errors.

KAIC02000-KAIC02999

Security (SEC) layer errors (user authentication, etc.).

See:

Table 1-2

Table 1-3

Table 1-4

KAIC06000-KAIC06999

KAIC07000-KAIC08999

Storage array errors (SNMP, etc.).

Command (Agent) errors.

Table 1-5

Table 1-6

Table 1-7

Table 1-8

Table 1-9

Table 1-10

Table 1-11

Note: Variable parameters in the error description are represented as

"parameter" or "value". These parameters or values are replaced in the message by the appropriate parameter or value. For example, "name" in the message "Duplicate name error, "name" already exists in the collection

" is replaced with the name that was duplicated.

1-2 Hitachi Device Manager Messages


The tables shown below list Hitachi Device Manager server error messages, and provide recommended actions for resolving those errors. The error messages are listed in numerical order of their error code. For errors whose recommended action is "Contact the Support Center", first collect maintenance information by executing the hcmdsgetlogs command, and then contact the

Hitachi Data Systems Support Center (see

Calling the Hitachi Data Systems

Support Center

for contact information).

Table 1-2 KAIC00000-KAIC00999: Hitachi Device Manager Server Errors

Error Code

KAIC00000-E

KAIC00001-E

KAIC00002-E

KAIC00003-E

KAIC00004-E

KAIC00100-E

KAIC00101-E

KAIC00102-E

KAIC00103-E

KAIC00104-E

KAIC00105-E

KAIC00106-E

KAIC00107-E

Description Recommended Action

An unspecified error was encountered.

An unspecified server error was encountered.

Contact the Support Center.

An error occurred in initializing the Device Manager Server.

See the server "error.log" for additional details.

The servlet instance is invalid. A request referenced a servlet not supported by Device Manager.

The transfer request format is incorrect.

Server initialization error: an invalid HTTP port number

"port-number" has been specified.

Server initialization error: an invalid HTTPS port number

"port-number" has been specified.

Server initialization error: an invalid document root directory

"directory-name" has been specified.

The transfer request format is invalid; correct the format, and then retry.

Check the Device Manager Server manual, confirm the value of "server.properties", and restart the Device Manager Server.

Server initialization error: an invalid bind address "bind-

address" has been specified.

Server initialization error: an unsupported JRE version "JRE-

version" has been specified.

Server initialization error:

Unable to load Servlet v2.2 classes.

Server initialization error:

Unable to load SNMP classes.

Make sure the version is JRE version, and restart Device Manager Server.

Make sure the servlet (JSDK v2.2+) can be loaded.

Server initialization error: An attempt to load Service

Modules has failed.

Make sure the Sun SNMP (JDMK) classes can be loaded and restart the Device Manager

Server.

The direct cause of this error is the immediately preceding error. Carry out the recommended action for that error. If this error continues to occur even after performing the action, or if these actions are inapplicable, contact the Support Center.



1-3

1-4

Error Code

KAIC00108-E

KAIC00110-E

KAIC00112-E

KAIC00113-E

KAIC00114-E

KAIC00115-E

KAIC00116-E

KAIC00120-E

KAIC00121-E

KAIC00123-E

KAIC00124-E

KAIC00125-E

KAIC00126-E

KAIC00150-E

KAIC00180-E

Description

Server initialization error: An error occurred while the entry

"entry-name" was loaded in the Device Manager Server

KeyStore.

An attempt to start Server failed: Serious errors occurred checking or updating the database.

The maximum number of connection threads, "number-

specified-for-maxThreads", was exceeded.

An attempt to construct

ServiceConnection failed.

An attempt to start the HTTP server on port "port-number" failed.

An attempt to start the HTTPS server on port "port-number" failed.

Server initialization error: The

IP address of localhost is unsolvable.

The config file

"server.properties" cannot be read.

Unable to read servlet config file "servlet.properties".

The MIME types file cannot be read.

During an attempt to change the user, group or root directory, and error occurred with the message "error-

message".

An attempt to read the configuration file

"product.properties" has failed.

An attempt to read the configuration file "file-name" has failed. Error detail : "error-

details".

An attempt to find the entry

"entry-name" in the Device

Manager Server KeyStore has failed.

Common Component is not installed.

Recommended Action


Check the Device Manager Server manual, confirm the value of "server.properties", and restart the Device Manager Server.


Check "server.http.port" in

"server.properties".

Check "server.https.port" in

"server.properties".


Check "server.properties", and restart the

Device Manager Server.

Check "servlet.properties", and restart the


Check "mime.properties", and restart the



Check the configuration file

"product.properties", and then restart the


Remove the cause of the error, and then restart the Device Manager Server. If this error continues to occur even after performing the action, contact the Support

Center.

The Device Manager Server KeyStore must be present and contain at least one entry to run the Device Manager Server in secure mode.




Error Code

KAIC00181-E

KAIC00182-E

KAIC00183-E

KAIC00184-E

KAIC00300-E

KAIC00405-E

KAIC00407-E

KAIC00408-E

Description

An attempt to set the installation destination of

Common Component has failed.

An attempt to acquire the

Common Component address has failed. ("method-name")

An error occurred in initializing the Provisioning Manager.

("method-name")

A directory necessary for storage subsystem management does not exist.

The Device Manager environment is invalid.

(directory name = directory-

name)

An attempt to bind the port

"port-number" for receiving the SNMP Trap has failed. This port is being used by other software.

An unexpected error occurred in the email notification functionality.

An email send error occurred.

(unsent email = (recipient email address = "recipient-

email-address"), Alert =

(messageID = "alert-ID", number = "number", type =

"type", source = "source", severity = "severity", component = "component", description = "description", actionToTake = "action-to-

take", data = "data", timeOfAlert = "time-of-alert"))

An attempt to connect to the

SMTP server has failed. (SMTP server = (host = "hostname-

or-IP-address", port = "port-

number"), unsent email =

(recipient email address =

"recipient-email-address"),

Alert = (messageID = "alert-

ID", number = "number", type

= "type", source = "source", severity = "severity", component = "component", description = "description", actionToTake = "action-to-

take", data = "data", timeOfAlert = "time-of-alert"))


Check "server.base.home" in

"server.properties", and contact the Support

Center.


Terminate any other software using this port, or set 'false' for

"server.dispatcher.daemon.receiveTrap" in the "dispatcher.properties" file, and restart



Make sure the following environment related items are correct:





Status and settings of the SMTP server

Status of the network

Make sure the following items related to the environment and the sending of email are correct:







Property settings for sending email

Status and settings of the SMTP server

Status of the network



1-5

1-6

Error Code

KAIC00409-E

KAIC00410-E

KAIC00411-E

KAIC00412-E

KAIC00413-E

KAIC00414-E

Description

A connection to the SMTP server could not be established because authentication failed.

(SMTP server = (host =

"hostname-or-IP-address", port = "port-number"), unsent email = (recipient email address = "recipient-email-

address"), Alert = (messageID

= "alert-ID", number =

"number", type = "type", source = "source", severity =

"severity", component =

"component", description =

"description", actionToTake =

"action-to-take", data =

"data", timeOfAlert = "time-of-

alert"))

The value specified for a property is incorrect. The system will use the default value for the property. (file name = "file-name", property name = "property-name", specified value = "specified-

value", default value =

"default-value")

Authentication information for connecting to the SMTP server has not been set. The email will be sent without SMTP authentication.

The recipient email address is invalid. (user ID = "user-ID", recipient email address =

"recipient-email-address") The email will not be sent to this user ID.

The template file was not found. (template file path name = "template-file-path-

name") The default template file will be used to send the email.

An error occurred while the template file was being loaded.

(template file path name =

"template-file-path-name", detailed information =

"detailed-information") The default template file will be used to send the email.


Change the SMTP server settings so that the relevant user can be authenticated. Also, use the command for setting the SMTP authentication user information to set the

SMTP authentication user information (user

ID and password).

If the default value does not cause any problems, no further action is required. If you specify a value different from the default value, make sure that the property settings are correct, and then restart the Device

Manager server.

Set the SMTP authentication user information

(user ID and password) by using the hdvmmodmailuser command. If SMTP authentication is not required for the email, no further action is required.

Specify a valid address by using the user management functionality's Edit Profile dialog box.

Check whether the template file indicated in the message exists. If you use the default template file, no further action is required.

Remove the cause of the error according to the detailed information. If you use the default template file, no further action is required.



Error Code

KAIC00415-E

KAIC00416-E

KAIC00417-E

KAIC00418-E

KAIC00419-E

KAIC00420-E


The size of the template file is too large. (template file name

= "template-file-name", template file size (bytes) =

"template-file-size-in-bytes", maximum file size (bytes) =

"maximum-file-size-in-bytes")

The default template file will be used to send the email.

An invalid header exists.

(template file name =

"template-file-name", line number = "line-number", header name = "header-


A header has not been specified. (template file name

= "template-file-name", header name = "header-


The same header name is duplicated. (template file name

= "template-file-name", line number = "line-number", header name = "header-


The header section in the template file contains an invalid line. The name and contents of a header must be separated with a colon (:).


"template-file-name", line number = "line-number") The default template file will be used to send the email.

In the template file, the size of a line is too large. (template file name = "template-file-

name", line number = "line-

number", detected line size

(bytes) = "detected-line-size-

in-bytes", maximum line size

(bytes) = "maximum-line-size-

in-bytes") The default template file will be used to send the email.

Revise the contents of the template file, and reduce the file size. If you use the default template file, no further action is required.

Revise the characters used in the header name specified in the template file. If you use the default template file, no further action is required.

Revise the headers specified in the template file. If you use the default template file, no further action is required.

Revise the contents of the template file to reduce the line size. If the default template file is used, no action is required.



1-7

1-8

Error Code

KAIC00422-E

KAIC00423-E

KAIC00424-E

KAIC00425-E

KAIC00426-E

KAIC00427-E

KAIC00428-E

KAIC00500-E

KAIC00501-E

KAIC00504-E

KAIC00505-E

KAIC00506-E

Description

The user ID entered for SMTP authentication is invalid.

The password entered for

SMTP authentication is invalid.


Enter a valid user ID for SMTP authentication, using from 1 to 64 characters. Specifiable characters for an SMTP authentication user ID are as follows:

A to Z, a to z, 0 to 9, and the following characters:

- _ . , @ ! # $ % & ' * + = ? ^ |

When specifying a password for SMTP authentication, enter a valid password using from 0 to 64 characters. Specifiable characters for the SMTP authentication password are as follows:

A to Z, a to z, 0 to 9, and the following characters:

- _ . , @ ! # $ % & ' * + = ? ^ |

The password can be omitted.

Specify the correct user ID and password. The user ID or password of

Device Manager is invalid.

The entered Device Manager user does not have permission to execute the command.

An internal error occurred.

The command syntax is invalid.

In the template file, there is no blank line to indicate the end of the header section.


"template-file-name")

The request contained improperly formatted data.

The device is not supported by


Explanation = "subsystem".

"specified-name" is a reserved name and cannot be used as a top-level logical group name.

The Device Manager server does not support the specified array family.

Simultaneous LUN Scans of the subsystem are not allowed.

When executing the command, make sure the

Device Manager user has the Admin permission.


Revise the command syntax.

Add a blank line at the end of the header section. If the default template file is used, no action is required.

Correct the request, and then retry.

Confirm that the IP Address in the request is correct. It is also possible that a configuration error exists in the subsystem.

The CLI or another client has tried to use a reserved group name (e.g., Unallocated). You cannot use the names "Unallocated" or "LUN

Scan" for a top-level logical group.

Check the array family.

Only one LUN Scan can be performed on a storage array at a time. Make sure that only one Device Manager Server is actively managing the subsystem.



Error Code

KAIC00507-E

KAIC00508-E

KAIC00509-E

KAIC00510-E

KAIC00511-E

KAIC00513-E

KAIC00514-E

KAIC00515-E

KAIC00530-E

KAIC00600-E

KAIC00601-E

KAIC00604-E

KAIC00700-E

KAIC00800-E

KAIC00801-E

KAIC00802-E

KAIC00805-E

KAIC00806-E

KAIC00807-E


The command "command-

name" is not supported under this API version.

The command "command" is not supported for the array family "family-name" under this API version.

This Device Manager Server does not support the API version "version".

The family of the target storage is not "storage-family".

The definition of storage name

"storage-name" is invalid.

The servlet name "xml-servlet-

name" in the request does not match the specified servlet name "specified-servlet-

name".

The command "specified API

name" is not supported by the


The executed command

"command-name" does not support the specified array family in this API version.

Device Manager Server does not support the operation by

API version "version" for this subsystem.

An internal server error occurred.

Check the Device Manager Server XML API manual and make sure that the running API version supports the command.

Make sure that the specification is valid.

Make sure the storage name relations in the config files are valid.

Make sure that the servlet name in the request is same as the specified servlet name.

Check the Device Manager Server XML API manual and make sure that the running API supports the command.

Find out which API versions support this command.


If this problem persists, contact the Support

Center.

Make sure that the objects are valid. An invalid parameter of a managed object was detected.

An attempt to initialize the

Common Component Logger has failed.




An internal error occurred while Dynamic Link Manager was starting.

An internal error occurred while NAS Manager was starting.

Make sure that the Common Component is installed.


An attempt to start NAS

Manager has failed.


Center.

An attempt to start has failed. Contact the Support Center.



1-9

1-10

Error Code

KAIC00809-E

KAIC00810-E

KAIC00811-E

KAIC00812-E

KAIC00813-E

KAIC00814-E

KAIC00816-E

KAIC00817-E

KAIC00818-E

KAIC00819-E

KAIC00820-E

KAIC00821-E

KAIC00822-E

KAIC00823-E

Description

The specified program cannot start because of a communication failure with the host agent.

The parameter "parameter-

name", which is required to start the specified program, is missing.

An error occurred in Common

Component. Device Manager cannot be started.

A file access error occurred.

Device Manager cannot be started.

An attempt to connect the device at IP Address "IP-

address" has failed. NAS

Manager cannot be started.

The correct IP address for the device is not found. NAS


An I/O error occurred. Device


Startup cannot be performed because an I/O error occurred.

An I/O error occurred. NAS


The startup method for

"Function the user tried to

execute" is invalid.

Settings for linking with program-name(Disk Array

Management Program or

Storage Navigator Modular) are invalid.

An internal error occurred while Disk Array Management

Program was starting.

An attempt to start Disk Array

Management Program has failed. The Disk Array

Management Program service might not be running correctly, or a setting in the launchapp.properties file might be incorrect, or a setting related to the Disk Array

Management Program network might be incorrect.

Disk Array Management

Program could not be started because an I/O error occurred.



Center.


Check the state of the network and the device.


Check the operating environment. If this problem persists, contact the Support Center.

Use Device Manager Web Client to start

"Function the user tried to execute".

Revise the settings for linking with programname(Disk Array Management Program or

Storage Navigator Modular) by referring to the Device Manager Server manual. If this problem persists, contact the Support Center.


Make sure the Disk Array Management

Program service is running correctly, the settings in the launchapp.properties file are correct, and the settings related to the Disk

Array Management Program network are correct. Also, if the Storage Navigator

Modular service is running, stop it. If the error continues to occur after you perform these actions, or if the actions do not apply, contact the Support Center.

Check the operating environment. If this problem persists, contact the Support Center.



Error Code

KAIC00824-E

KAIC00825-E

KAIC00826-E

KAIC00827-E

KAIC00828-E

Description

An attempt to delete registered unit information from Disk

Array Management Program has failed.

The launch parameter is invalid.

A Disk Array Management

Program server error occurred.

(error code = "Error Code from

DAMP Server", error message

= "Error Message of DAMP

server error code")

A setting for using "Disk Array

Management Program" has not been made or is invalid. The corresponding storage subsystem is not registered or is incorrectly registered with

Disk Array Management

Program. To use "Disk Array

Management Program", a setting for linking with Disk

Array Management Program is necessary. Confirm that the corresponding storage subsystem is correctly registered in Disk Array

Management Program.

Startup cannot be performed because a refresh has not been executed for the storage subsystem.



Reference the Device Manager Server manual and revise the settings for linking with related products. If this problem persists, contact the

Support Center.

Refresh the storage subsystem.



1-11

Error Code

KAIC00829-E

KAIC00830-E

KAIC00831-E

KAIC00832-E

KAIC00833-E

Description

An internal error occurred while Storage Navigator

Modular was starting.

An unexpected error occurred while Storage Navigator

Modular was starting.

An error occurred in the

Storage Navigator Modular.

(error code = "error code from

Storage Navigator Modular

Server", error message =

"error message for Storage

Navigator Modular error code")

A setting for using "function

name(Physical View or Storage

Navigator Modular)" has not been made or is invalid. The corresponding storage subsystem is not registered or is incorrectly registered with

Storage Navigator Modular. To use "function name(Physical

View or Storage Navigator

Modular)", a setting for linking with Storage Navigator

Modular is necessary. Confirm that the corresponding storage subsystem is correctly registered in Storage Navigator

Modular.

An attempt to start Storage

Navigator Modular has failed.

The Storage Navigator Modular service might not be running correctly, or a setting in the launchapp.properties file might be incorrect, or a setting related to the Storage

Navigator Modular network might be incorrect.




Support Center.

Make sure the Storage Navigator Modular service is running correctly, the settings in the launchapp.properties file are correct, and the settings related to the Storage Navigator

Modular network are correct. Also, if the Disk

Array Management Program service is running, stop it. If the error continues to occur after you perform these actions, or if the actions do not apply, contact the Support

Center.



Error Code

KAIC00834-E

KAIC00835-E

KAIC00836-E

KAIC00837-E

KAIC00838-E

KAIC00839-E

KAIC00840-E

Description

A setting for using "function

name(Physical View or Storage

Navigator Modular)" has not been made or is invalid.

Storage Navigator Modular cannot be accessed

(URL="access URL"). To use

"function name(Physical View

or Storage Navigator

Modular)", a setting for linking with Storage Navigator

Modular is necessary. Revise the access URL and alias settings. Specify the Storage

Navigator Modular URL for the launchapp.damp.url property in the launchapp.properties file. To set alias information, execute the alias information setting command (HWSAlias).

To apply the settings, restart

Common Component and


The target storage subsystem does not support launching.

(microcode version =

"microcode version")

The registration for the linking functions failed

(cause="cause"). Check again after some time.



Support Center.

Check the version of the storage subsystem microcode.

Access to the storage subsystem may be in conflict. Please wait and then retry the operation. If this error continues to occur, the value set for server.http.host

in the server.properties

file might be invalid.

Refer to the Device Manager Server manual and, if necessary, revise the value set for server.http.host

. If you change the setting, restart the Device Manager server. If this problem still occurs after these actions, contact the Support Center.

Delete unnecessary users from storage subsystem, and then retry the operation.

The launch has failed. No more launch users can be registered because the maximum number of launch users has already been registered in the specified storage subsystem.

The launch has failed. A user

ID that is the same as the launch user ID is already registered in the storage subsystem.

An internal error occurred while Storage Navigator was starting.

The launch has failed. The configuration of purchasable optional features on the storage subsystem might have changed.

Delete the already registered user ID from the storage subsystem, and then retry the operation.


Refresh the storage subsystem, and then try again.



1-13

1-14

Error Code

KAIC00841-E

KAIC00843-E

KAIC00850-E

KAIC00851-E

KAIC00852-E

KAIC00853-E

KAIC00854-E

KAIC00855-E

KAIC00856-E

KAIC00857-E

KAIC00858-E

Description

The launch has failed. Storage

Navigator Modular (for Web) set for linking does not support the specified subsystem.

The launch has failed. Based on the current Device Manager server settings, the specified subsystem cannot be launched.

An attempt to read a file has failed. The file does not exist or you do not have read permission for it. (file path =

"file path")

An attempt to create a temporary file has failed. You do not have write permission or disk space is insufficient.

(file path = "file path")

Configuration of the remote connection settings for the

DBMS has failed. Disk space is insufficient.


DBMS has failed. An internal error occurred.


DBMS has failed. Execution of an internal command failed.

(executed command =

"executed command")

An error occurred while a value was being entered from standard input.

An internal error occurred while executing the Tuning

Manager connection setup tool.

An internal error occurred while processing to set up database users for other suite products.


DBMS has failed. Execution of an internal command failed.

(executed command =

"executed command", exit code = "exit code", command message = "command

message")


Check the version of Storage Navigator

Modular (for Web).

If the specified storage subsystem is managed using an IPv6 IP address, specify the IPv6 IP address or host name for the

"server.http.host" property in the

"server.properties" file.

Make sure that the file exists and that you have read permission for it, and then execute the setup tool again.

Make sure that you have write permission and that disk space is sufficient, and then execute the setup tool again.

Make sure disk space is sufficient, and then execute the setup tool again.


Execute the setup tool again.




Error Code

KAIC00859-E

KAIC00860-E

Description


DBMS has failed. The Common

Component service is running.

The storage array was not found in the Device Manager database.


Stop the Common Component service, and then execute the setup tool again.

Check the coding of storage array.

Table 1-3 KAIC01000-KAIC01999: Translation Errors (HTTP, XML format)

Error Code

KAIC01000-E

KAIC01001-E

KAIC01003-E

KAIC01011-E

KAIC01012-E

KAIC01013-E

KAIC01014-E

KAIC01015-E

KAIC01016-E

KAIC01017-E

KAIC01018-E

Error Message

An unspecified XML translation error was encountered.

XML translation error: An error occurred parsing the XML: "XML-

parser-error-message".

XML translation error: Posted entity is not XML.

"attribute-value" is not a valid value for parameter "attribute-

name". Enter a parameter of the

"attribute-data-type" type.

XML translation error: An internal error occurred.

An invalid element "element-

name" was specified in the XML request.

An invalid parameter

"parameter-name" was specified in the XML request element

"element-name".

An invalid value was specified for the parameter "parameter-

name" in the XML request element "element-name".

An invalid child element "child-

element-name" was specified in the XML request element

"parent-element-name".

An attempt to execute a request has failed. Under the current license, the user who made the request does not have permission to execute commands.

An attempt to execute a request has failed. Under the current license, the specified command cannot be executed.



Check the request code.

Correct the value of "attribute-data-type", and then retry.


Check the request code.

Execute this command as a user who has

Core License permissions.

This command can only be executed when using the Full License.



1-15

1-16

Error Code

KAIC01019-E

KAIC01021-E

KAIC01022-E

Error Message Recommended Action

The license is invalid.

The format of command option 2 is incorrect.

The name "option-name" is specified twice for command option 2.

Specify either the Full License or Core

License.

Revise the request, and then retry the operation.

Table 1-4 KAIC02000-KAIC02999: Security Layer Errors: User

Authentication, Etc

Error Code

KAIC02001-E

KAIC02002-E

KAIC02004-E

KAIC02006-E

KAIC02007-E

KAIC02009-E

KAIC02010-E

KAIC02011-E

KAIC02012-E

KAIC02013-E

KAIC02014-E

KAIC02015-E

KAIC02016-E

KAIC02017-E

KAIC02018-E


Duplicate user group names are not allowed.

The user group was not found in the Device Manager database.

The rule was not found in the

Device Manager database.

The user ID or the password is incorrect.

Duplicate user IDs are not allowed.

The record was not found in the Device Manager database.

Duplicate records are not allowed.

The user "user-ID" has an active request, and cannot be deleted.

The specified user group cannot be added under this API version.

The specified user cannot be added under this API version.

Access permission error.

An internal error occurred during user authority checking.

The specified logical group is already being used by another user group.

The specified user group is already associated with another logical group.

A user is already registered in the specified user group.

Make sure that the user group name is not a duplicate, and then retry.

Make sure that the user group name exists in the Device Manager database, and then retry.

Check the ACL ruleID.

Make sure that the user ID and the password exist.

A duplicate user ID cannot be registered into the Device Manager ACL database. Change the user ID.

This is an informational message only. No additional action is required.

Try to delete the user once the operation completes.

Check the Device Manager Server XML API manual and make sure the running API version supports the command.

Check the access permission of the user.


Specify another logical group, and then retry.

Remove the old association, and then retry.

Remove all users from this user group, and then retry.



Error Code

KAIC02019-E

KAIC02020-E

KAIC02021-E

KAIC02022-E

KAIC02023-E

KAIC02024-E

KAIC02025-E

KAIC02026-E

KAIC02027-E

KAIC02028-E

KAIC02030-E

KAIC02032-E

KAIC02033-E

KAIC02034-E

KAIC02035-E

KAIC02036-E

KAIC02037-E

Description

A user group is registered under the specified logical group.

A user group is registered in the specified logical group.

The specified object ID

"ObjectID" was not permitted for the login user.

The logged-in user does not have permissions for the specified host "host-name".

The login user cannot remove a LUSE that includes an unpermitted LDEV.

The login user cannot add a path to an unpermitted LDEV.

The login user cannot remove a path that set an unpermitted

LDEV.

The local user does not have permission to add a new subsystem.

The local user does not have permission to remove a subsystem.

An object for which the loggedin user does not have permissions was specified.

The user "userID" does not have permission to run this

API.

The login user cannot modify own user group and user role.

The login user cannot operate a replication using an unpermitted LDEV.

The user group name is invalid. Use name less than 25 bytes.

The specified ACL rule already exists in the Device Manager database.

A path related to the LDEV to be deleted is registered in the logical group "logical-group-

name".

This operation cannot be performed because the specified user ID is reserved within Device Manager.


Remove all user groups under the specified logical group, and then retry.

Create a new logical group, and then add a path in the logical group.

Check the ACL rule, and then retry.

Check the ACL rule for the logged-in user.


Ask Global-Admin or Global-Storage_Admin to add the new subsystem.

Check the ACL rule for the logged-in user.


Check the login user authorization, and then retry.


The user group name is invalid. Use name less than 25 bytes.

Revise the rule, and then retry.

From the logical group, remove the path related to the LDEV to be deleted.

Change the user ID, and then retry.



1-17

1-18

Error Code

KAIC02038-E

KAIC02040-E

KAIC02041-E

KAIC02042-E

KAIC02043-E

KAIC02044-E

KAIC02045-E

KAIC02046-E

KAIC02047-E

KAIC02048-E

KAIC02100-E

KAIC02101-E

KAIC02150-E

KAIC02250-E

KAIC02251-E

KAIC02252-E

Description

The storage port "Host Name" cannot set access permissions.

Built-in user groups cannot be deleted.

The own user group cannot be deleted.

Built-in user groups cannot be modified.

The own user group cannot be modified.

The login user cannot delete own account.

A user being used by other products (using shared user information) cannot be deleted.

The requested operation cannot be executed to the specified user.

The specified ACL rule ID is invalid. It cannot be deleted.

The specified user group name cannot be used because it is reserved.

The logged-in user does not have the permissions for using

Device Manager functions.

The logged-in user cannot use

Device Manager functions because that user does not belong to a user group.

There are no permissions to use the journal group.


Check and, if necessary, revise the target host specification.

Revise the user group specifications.

Revise the user specifications.

Revise the ACL rule specifications.


Try again as a user who can use Device

Manager functions.

A PP Name (VolumeMigration) migration plan related to an

LDEV for which the logged-on user does not have the necessary permissions cannot be specified.

An LDEV that does not have the necessary permissions cannot be specified as a source volume.

An LDEV that does not have the necessary permissions cannot be specified as a target volume.

Revise the request, and then retry. To use a journal group, the user must have permissions for all the volumes that make up the journal group.

Check the ACL rule for the logged-on user.



Error Code

KAIC02253-E

KAIC02500-E

KAIC02501-E

KAIC02502-E

KAIC02503-E

KAIC02504-E

KAIC02505-E

KAIC02506-E

KAIC02507-E

KAIC02508-E

Description

For an LDEV that does not have the necessary permissions, no PP Name

(VolumeMigration) reserved volume set or release operation can be performed.

An unspecified error occurred while performing an operation on the common user information.

An exception occurred in the common user management function.

Part of the user group information is inconsistent with part of the common user information.

The specified user is not registered in the common user information.

The specified user has already been registered in the common user information.

The specified user group is not registered in the common user information.

The specified user group has already been registered in the common user information.

The common user management function is unavailable.

This operation cannot be processed since it is invalid.



The common user information might not contain the latest information. Restart the

Device Manager server.

Revise the user specifications.


Check whether the Common Component service is running.

Revise the operation.



1-19

1-20

Error Code

KAIC02509-E

Description

A communication error occurred during an attempt to authenticate a user on an external authentication server.


Perform one of the following procedures:

For LDAP:

1. By using the host, port, and protocol set in exauth.properties, check whether the authentication server can be accessed, the settings of the external authentication server, and the status of the network.

2. By using the hcmdsldapuser command, check that the information for the server names specified in the auth.server.name attribute in exauth.properties is registered.

3. If StartTLS is used, check the SSL settings.

4. If you cannot resolve the problem, collect maintenance information, and then contact the Support Center.

For RADIUS:


2. By using the hcmdsradiussecret command, check that the information for the server names specified in the auth.server.name attribute in exauth.properties is registered.

3. If you cannot resolve the problem, collect maintenance information, and then contact the Support Center.

Table 1-5 KAIC03000-KAIC03999: Database Errors

Error Code

KAIC03000-E

KAIC03001-E

KAIC03002-E

KAIC03003-E

KAIC03004-E

KAIC03005-E

KAIC03006-E

Description

An unspecified database error was encountered.

The specified object was not found in the Device Manager database.

The ManagedObject does not support name updates.

The device cannot read/write to


The database manager handle is not valid.

An error was encountered during database query.

An error was encountered during database insert.



Make sure that the specified object exists in the Device Manager database, and then retry.

If the name has to be changed, the object will have to be deleted and re-added.

An internal server error was encountered. If this problem persists, contact the Support

Center.


Center.



Error Code

KAIC03007-E

KAIC03008-E

KAIC03009-E

KAIC03010-E

KAIC03011-E

KAIC03012-E

KAIC03013-E

KAIC03014-E

KAIC03015-E

KAIC03016-E

KAIC03017-E

KAIC03018-E

KAIC03019-E

KAIC03020-E

KAIC03021-E

KAIC03022-E

Description

An error was encountered during database update.

An error was encountered during database delete.

The database column "column-

name" was not found in the result set.

An error was encountered during the formatting of the database results for the column

"column-name".

An attempt to acquire a database connection from the pool failed. Check communications to the Device

Manager database.

A failure was encountered during the closing of a database connection.

A failure was encountered during the committing of a database transaction.

A failure was encountered during the rolling back of a database transaction.

Database transaction commit/rollback failed. No transaction is in progress.

The entered value exceeds the maximum number of allowable digits. Enter a valid value.

Due to competing database locks, all or a part of the requested update has failed.

An attempt to migrate the

Device Manager database has failed. (return code="return

code")

An attempt to convert a character code has failed.

An attempt to execute the command for releasing index free pages has failed.

An attempt to add the command for updating the database has failed.

Device Manager access to DB is blocked. Problem is detected in

Common Component. Call server administrator.


Enter a valid value.


Center.

If this problem occurs repeatedly, contact the

Support Center.

If this problem occurs repeatedly, contact the

Support Center.


Center.

Call server administrator.



1-21

1-22

Error Code

KAIC03023-E

KAIC03050-E

KAIC03051-E

KAIC03052-E

KAIC03100-E

KAIC03141-E

KAIC03143-E

KAIC03144-E

KAIC03145-E

KAIC03146-E

KAIC03147-E

KAIC03148-E

KAIC03149-E

KAIC03402-E

Description


Device Manager database. Call server administrator.

The ID of table "Table" has exceeded the maximum.

Mapping of the "type-name" type for database access cannot be resolved.

Initialization of table "Table

name" ("Key") has been duplicated.

An error occurred during the connecting to the Device

Manager database.

An internal server error was encountered. An attempt to acquire the URL of the host agent failed.

An internal server error was encountered. An attempt to acquire the replication information failed.

An internal server error was encountered. An attempt to acquire license key information from the database has failed.

(Cause:"cause")

An internal error occurred. The record relating to the subsystem could not be deleted from the database. (cause =

"cause")

An internal error occurred. The

SMI-S Enabled subsystem information could not be acquired from the database.

(table name = "table name")


Acquisition of information used for managing the status of table

"table name" has failed.


Acquisition of information to set for table "table name" has failed.

An internal error occurred. An attempt to acquire the virtualization server information from the database failed. (table name: table name)

A connection error occurred when logging into the Common

Component.





Center.





Check Common Component, and then retry.



Error Code

KAIC03403-E

KAIC03404-E

KAIC03405-E

KAIC03406-E

KAIC03410-E

KAIC03411-E

KAIC03412-E

KAIC03414-E

KAIC03415-E

KAIC03416-E

KAIC03420-E


An attempt to log into the

Common Component failed.

Application "ApplicationName" is not permitted to log in.

Authentication was refused when logging into the Common

Component. "userID"

A Common Component error occurred.

An error occurred while connecting to the Common

Component database.

An error occurred during operation of the Common

Component database. (CIM error: "error-code")


Data in the Device Manager database might not match data in the Common Component database. Specify "true" for the property

"server.base.initialsynchro" in the

"server.properties" file, restart Device

Manager Server, and then retry the operation. If this problem still occurs after these actions, Contact the Support Center.

Contact the Support Center. An attempt to acquire Device

Manager information for synchronizing with Common

Component has failed.

An internal error occurred while updating the Common

Component database.

An exception occurred in the

Common Component linkage of

Provisioning Manager.

Specify "true" for the property


"server.properties" file, and then restart

Device Manager Server. If this problem persists, contact the Support Center.

Specify "true" for the property server.base.initialsynchro in the server.properties file, and then restart Device

Manager Server.

An error occurred while updating the Common

Component database.

Mismatching data existed in the

Device Manager database and the Common Component database.

The rollback of the Device

Manager database was performed after updating the

Common Component database.Therefore, mismatching occurred in the

Device Manager database and

Common Component database.

An attempt to register the initial data into the Common

Component database has failed.

Specify "true" for the property


"server.properties" file, and restart Device

Manager Server.

Check whether the Common Component service is running.



1-23

Error Code

KAIC03421-E

KAIC03422-E

KAIC03423-E

KAIC03440-E

KAIC03441-E

KAIC03500-E

KAIC03999-E

Description

An attempt to synchronize with

Common Component has failed.

An attempt to determine synchronization with Common

Component has failed.

"StartingState"

An attempt to synchronize with the information for the displayed list has failed.

An attempt to acquire the accessing user ID and password for the database has failed.



Database migration has failed.

A database error occurred during an attempt to add a storage subsystem or refresh the database. Try again.

An error occurred during the initialization of the Device

Manager database functionality.

Make sure that the Common Component service has started, and then restart Device

Manager Server. If this problem occurs repeatedly, contact the Support Center.



Center.

Make sure that the Device Manager service is started, and that the Device Manager database exists. If this problem persists, contact the Support Center.

Table 1-6 KAIC04000-KAIC04999: Network Errors

Error Code

KAIC04001-E

KAIC04002-E

Description

An attempt to resolve the specified IP address "IP-

address" has failed.

The specified IP address "IP

address" is not a correctly formatted protocol address.


Specify the correct IP address.

Revise the specification.



Error Code

KAIC04100-E

KAIC04211-E

KAIC04212-E

KAIC04213-E

Description

An internal error occurred. An incorrect format for the IP address "IP-address" was detected.

An exception occurred when

Storage Navigator Modular was invoked. (exception="stack-

trace")

An exception occurred while

Storage Navigator Modular event history information was being acquired.

(exception="stack-trace")


Storage Navigator Modular.

(error code = "error code from

Storage Navigator Modular

Server", error message =

"error message for Storage

Navigator Modular error code")



Table 1-7 KAIC05000-KAIC05999: Transport Errors

Error Code

KAIC05000-E

KAIC05001-E

KAIC05002-E

KAIC05003-E

KAIC05004-E

KAIC05005-E

Description

An unspecified transport error was encountered.

Device Manager does not support the operation

"operation" for the storage array type.

An internal server error occurred. The transport connection is not valid for the storage array.

The storage subsystem is currently locked by "user-

name".



Device Manager Server does not support requests on the specified storage device.


An attempt to acquire the lock for the subsystem has failed.

An attempt to release the SNMP lock has failed after "number-

of-trials" attempts.

The storage array is locked by another management application. Check whether anyone is accessing the storage array from another management application on the network. If this problem persists, contact the

Support Center.

Check whether anyone is accessing the storage array from another management application on the network. If this problem persists, contact the Support Center.



1-25

1-26

Error Code

KAIC05008-E

KAIC05009-E

KAIC05011-E

KAIC05012-E

KAIC05013-E

KAIC05014-E

KAIC05015-E

KAIC05016-E

KAIC05018-E

KAIC05019-E

KAIC05020-E

KAIC05022-E

KAIC05023-E

KAIC05024-E

KAIC05026-E

KAIC05027-E

Description

An SNMP error occurred during an internal refresh of the subsystem.

An attempt to retrieve info via

SNMP has failed.


DeviceIdentificationService was not found.

No default service is registered for identification of the array family "array-family".

An error occurred during acquisition of configuration information from the device at

IP Address "IP-address".

Device Manager does not support the specified operation

"operation" on the subsystem.

The minimum microcode version is "version".

The specified array group

"array-group" is out of range.


"array-group" already exists.

The specified PDEV "PDEV-ID" is already in use.

The specified LDEV "device-

number" is out of range.


number" already exists.

The specified host mode is invalid for the storage subsystem. The setting for the storage subsystem type does not match the actual value.

The specified host mode is unsupported on the subsystem.

The function "Function-name" on the subsystem does not exist.

Device Manager does not support the specified subsystem, or a configuration error might exist in the subsystem.

The number of devNums required to create the specified

LU in the current configuration do not exist.


Center.



This is an internal server error indicating an invalid configuration in the transport layer.


An error was encountered during polling for device configuration information. Check the storage array for possible problems. If this problem persists, contact the Support

Center.

To perform this operation, the microcode version must be updated.

Perform a refresh on the storage subsystem.

Specifying the correct model, add the storage subsystem again. If there is a serious impact on your system, contact the

Support Center.

Check that the subsystem supports this host mode.

Check the subsystem functionality.

Revise the subsystem specifications. If there is no problem in the specifications, contact the Support Center.

Delete any unnecessary LUs, and then retry.



Error Code

KAIC05028-E

KAIC05030-E

KAIC05031-E

KAIC05032-E

KAIC05034-E

KAIC05035-E

KAIC05036-E

KAIC05040-E

KAIC05041-E

KAIC05042-E

KAIC05043-E

KAIC05044-E

KAIC05045-E

Description

The PP Name(Dynamic

Provisioning) ArrayGroup has been specified. A PP

Name(Dynamic Provisioning) volume cannot be created in

Device Manager.

Cannot create the LDEV with the specified emulation type under present storage configuration.

The specified emulation type is invalid for the array group.

An LDEV cannot be created for an array group of the emulation type "emulation-type".

The subsystem type is invalid.

An LDEV that has the emulation type "emulation-type" cannot be created for the specified device number

(devNum="device-number").

The specified device number

(devNum="device-number") cannot be used.

Operations for command device security are not supported on the microcode version of this subsystem.

The specified SMI-S Enabled subsystem was not found.

An SMI-S Enabled subsystem was not found. The specified

SMI-S provider does not manage any SMI-S Enabled subsystems supported by

Device Manager.

The specified virtualizationserver management program or virtualization server was not found.

No virtualization servers were found. The specified virtualization-server management program is not managing any virtualization servers supported by Device

Manager.

The information acquired from the specified virtualization server does not match the information in the database.


Revise the ArrayGroup specification.

Delete any unnecessary LUs, and then retry.

Correct the specified emulation type and/or array group, and then retry.

Check the specified emulation type.

Revise the specified subsystem type.

Revise the specified devNum or emulation type.

Revise the specified devNum.

To perform command device security operations, you will need to upgrade.


Revise the specification of the SMI-S Enabled subsystem.

Revise the SMI-S provider specification.

Revise the specification for the virtualizationserver management program or virtualization server.

Revise the specification for the virtualizationserver management program.

Delete the virtualization server from the

Device Manager server, and then re-register the virtualization server information.



1-27

1-28

Error Code

KAIC05054-E

KAIC05056-E

KAIC05057-E

KAIC05060-E

KAIC05090-E

KAIC05100-E

KAIC05101-E


The parameter (IP address or communication protocol) used to connect to the storage subsystem has been changed in

Storage Navigator Modular 2.

Make sure the IP address and communication protocol are correct, and then refresh the storage subsystem.

An attempt to connect to the storage subsystem failed. Check the specified storage subsystem type, IP address, microcode version, and network port settings, as well as the network status.

An attempt to connect to the storage subsystem failed. Check the specified storage subsystem type, IP address, communication protocol, microcode version, and network port settings, as well as the network status.

The IP address and communication protocol used to connect to the storage subsystem must be the same as those set in Storage

Navigator Modular 2. Check the network environment and the IP address and communication protocol used to connect to the storage subsystem. If necessary, specify the correct IP address or communication protocol, and then refresh the storage subsystem to obtain the most up-to-date configuration information.

Check the following items related to the storage subsystem:







Type

IP Address

Microprogram version



The ports that will be used. (Check from both Device Manager and the storage subsystem.)

The network status



If there is no problem with any of the above items, there is a hardware problem with the network or the storage subsystem.

Check the following items related to the storage subsystem:





Type

IP Address







Communication protocol

Microprogram version

The ports that will be used. (Check from both Device Manager and the storage subsystem.)



The network status

If there is no problem with any of the above items, there is a hardware problem with the network or the storage subsystem.

Revise the host specification. The host agent does not support the operation

"operation".

The specified operation is not supported by the microcode version of this storage subsystem.

An internal server error occurred. An attempt to execute the transport service failed due to a missing parameter

"parameter".

An internal server error occurred. An attempt to initialize the transport connection has failed.

To perform the specified operation, you will need to upgrade the microcode version.





Error Code

KAIC05102-E

KAIC05103-E

KAIC05200-E

KAIC05251-E

KAIC05252-E

KAIC05254-E

KAIC05255-E

KAIC05300-E

KAIC05302-E

KAIC05303-E

KAIC05304-E

KAIC05305-E

KAIC05306-E

Description

The subsystem or SMI-S provider is currently performing other processing. Wait a while, and then try again.

The virtualization-server management program or the virtualization server is currently processing. Wait a while, and then try again.

Initialization of the SNMP connection at IP-address "IP-

address" has failed.


Center.



Center.

The specified volume is already being used by another PP Name

(VolumeMigration) migration plan.

The specified PP Name

(VolumeMigration) migration plan was not found in the storage subsystem.


(VolumeMigration) migration plan cannot be deleted because migration has not finished.

The specified PP name

(VolumeMigration) migration plan cannot be canceled because it is not running.


An attempt to load a storage array connection library has failed.

An attempt to log in to the storage array has failed. Check the validity of the user ID and password. Moreover, please confirm whether the account registered in the storage subsystem is effective.

Permissions necessary to manage the subsystem are not allocated.

Another management application on the network is changing the subsystem configuration.

Specified PDEV are not continuous.

An error occurred during the initialization of the SNMP for the specified IP Address. This indicates a network connection or SNMP configuration error on the device.

Revise the volume specification.

Check and, if necessary, revise the specification.


Make sure the user ID and password are valid, and then retry the operation. If

Advanced Security mode is changed in the

Hitachi AMS or SMS series, all accounts registered in the storage subsystem are initialized. If this happens, create an account in Hitachi Storage Navigator Modular 2, and then retry the operation.

Make sure that the permissions to manage the subsystem are allocated. If this problem continues to occur, contact the Support

Center.

Make sure that the subsystem configuration is not being changed by another management application. If this problem continues to occur, contact the Support

Center.

Specify continuous PDEV. If the problem persists, contact the Support Center.



1-29

1-30

Error Code

KAIC05307-E

KAIC05308-E

KAIC05310-E

KAIC05311-E

KAIC05312-E

KAIC05313-E

KAIC05314-E

KAIC05315-E

KAIC05350-E

KAIC05381-E

KAIC05390-E

KAIC05391-E

KAIC05392-E

KAIC05393-E

Description

The number of PDEVs

("number-of-PDEVs") does not match the type "RAID-type".

You cannot delete the LU. You can only delete the last logical unit created. The last LU created was "device-number".

An attempt to connect to the storage array has failed. Check the validity of the storage type, and IP address, and DAMP connection port number, and network connectivity.

No more spare drives can be added on the subsystem.

No more command devices can be added to the specified subsystem.

An API function that was executed by the storage subsystem microcode is not supported.

The specified RAID type is invalid.

The Device Manager server does not support the specified subsystem.

The name of the virtualization server (host-name) detected for the specified IP address (IP-

address) is the same as a host name already registered in

Device Manager.

This Device Manager does not support the LUN Management option.

The port "port-name" was not found on the storage array.

The controller "controller-ID" was not found on the storage array.

HostStorageDomain "host-

storage-domain-ID" was not found on the storage array.

The specified Port Option "port-

option-name" is not supported on the microcode version of this subsystem.


A valid PDEV number needs to be assigned.

You can only delete the last logical unit created. The last LU created was "device-

number".

Confirm the storage subsystem type and IP address and subsystem connection port number are correct. If these are correct, there is a network or storage subsystem problem.

Remove other spare drives, and then retry.

Up to 2 LUs of command devices can be specified. Delete unnecessary command devices, and then retry.

Check the version of the storage subsystem microcode.

Check the request.

Make sure that the specified subsystem is supported by the Device Manager.

Revise the host name, and then try again.

Check this subsystem's option list.

Make sure that the port name is correct, and then retry. If this problem persists, contact the Support Center.

Make sure that the controller number is correct, and then retry. If this problem persists, contact the Support Center.

Make sure that the HostStorageDomain is correct, and then retry. If this problem persists, contact the Support Center.

A microcode upgrade is required to use the specified port option. Contact the Support

Center.



Error Code

KAIC05394-E

KAIC05395-E

KAIC05396-E

KAIC05400-E

KAIC05401-E

KAIC05402-E

KAIC05409-E

KAIC05420-E

KAIC05421-E

KAIC05422-E

KAIC05423-E

KAIC05424-E


An attempt to log in to the storage subsystem failed because another user is already logged in. Wait a while, and then retry the operation. If

Physical View, Storage

Navigator Modular or Storage

Navigator Modular 2 is open, close the window, and then retry the operation.

An attempt to register a user failed because the maximum number of users is already registered.

An attempt to register a user failed because the specified user ID is already registered.

An attempt to connect to the storage array at IP Address "IP-

address" has failed. Check the validity of the user ID and password, storage type, and IP address, as well as any network connections.

An attempt to retrieve data for the storage array has failed.

Check the validity of the user ID and password, as well as any network connections.

An attempt to execute the operation on the storage array has failed.

Wait a while, and then retry the operation. If

Physical View, Storage Navigator Modular or

Storage Navigator Modular 2 is open, close the window, and then retry the operation.

Delete unnecessary users from storage subsystem, and then retry the operation.

Revise the user ID or password specifications, and then retry the operation.

The HTTP connection command has failed.

Check the validity of the user ID, password, storage type, IP address, and network connections.

The HTTP GET command has failed to retrieve the desired data. Check the network connection and the user ID and password used to access the device. The Device

Manager Server may need to be refreshed to obtain the latest configuration information.

The HTTP POST command failed. Check the network connection and the user ID and password used to access the device. The

Device Manager Server may need to be refreshed to obtain the latest configuration information.

Perform a refresh on the storage subsystem, and then retry.

The chassis referenced in the request is not valid for the storage array.


There is no external array groups that Device Manager can assign.

An attempt to create the external array group "External

Array Group" has failed.

There is no path groups that

Device Manager can assign.

The specified LU cannot be created because the total capacity of that LU exceeds the capacity of the external volume.


Delete any unnecessary external array groups, and then try again.

Revise the external array group specification.

Delete any unnecessary path groups, and then retry the operation.

Revise the LU specification.



1-31

1-32

Error Code

KAIC05425-E

KAIC05500-E

KAIC05520-E

KAIC05521-E

KAIC05522-E

KAIC05523-E

KAIC05600-E

KAIC05601-E

KAIC05607-E

KAIC05609-E

KAIC05700-E

KAIC05701-E

KAIC05702-E

KAIC05703-E


An internal server error occurred. Execution of the transport service failed due to an invalid parameter value.

There is no response from the device at IP address "IP-

address".

The specified ISCSIName

"ISCSIName" does not exist.


"ISCSIName" already exists.

An attempt to execute a request has failed. Only some of the configuration changes may have been applied to the storage subsystem.

The request was not completed within the time limit. Only some of the configuration changes may have been applied to the storage subsystem.


An RMI connection could not be established using the IP address

IP-address. Check the specified type and IP address, as well as the network status.

The storage array at "IP-

address" is currently locked by another user, or is undergoing reconfiguration.

A RMI Session problem occurred at "IP-address".

Not enough free space exists.

An internal server error occurred. The

HostStorageDomainID is invalid.

The specified port already has the maximum number of LUNs.

The HostStorageDomain specified already has the maximum number of LUNs.


If the IP address of the storage subsystem is correct, there is a network connection error, or an SNMP configuration error in the device.


Refresh the storage subsystem, and make sure the request is correct.

Refresh the subsystem, check the parameter for the specified iSCSI port, and then retry the operation. If this problem persists, contact the Support Center.

Refresh the subsystem, and then check the changed settings. Specify the parameters for settings that have not yet changed, and then retry the operation. If this problem persists, contact the Support Center.


Make sure that the correct storage subsystem type and IP address have been specified. Also, check the settings for the

Device Manager and storage subsystem communication ports. Restart Device

Manager server if you have not done so since changing the storage subsystem microcode version. If there is no problem with the specifications or settings and restarting

Device Manager server does not solve the problem, there is a hardware problem with the network or the storage subsystem.

The storage array is locked by another management application. Wait a while, and then retry. If this problem persists, contact the Support Center.

This indicates a network or storage problem.

Specify the size within the scope of free space available.


No more LUNs can be specified on this port, so select a different port to which to add

LUNs.

No more LUNs can be specified on this

HostStorageDomain. Select a different

HostStorageDomain to which to add LUNs.



Error Code

KAIC05704-E

KAIC05705-E

KAIC05706-E

KAIC05707-E

KAIC05708-E

KAIC05709-E

KAIC05710-E

KAIC05711-E

KAIC05712-E

KAIC05713-E

KAIC05714-E

KAIC05715-E

KAIC05716-E

KAIC05717-E

KAIC05718-E


The LDEV of is a PP Name

(VolumeMigration) reserved volume; it cannot be used in a

LUSE.

The LU is an OnDemand device and cannot be used for an LUN.

The specified LDEV does not exist.

The specified WWN does not exist.

Perform a refresh on the storage subsystem and check the request.

Perform a refresh on the storage subsystem and check the request.

Perform a refresh on the storage subsystem to obtain the latest configuration information.

Perform a refresh on the storage subsystem to obtain the latest configuration information.

Check the request.

The specified port already has the maximum number of

WWNs.

The specified

HostStorageDomain already has the maximum number of

WWNs.

The specified WWN already exists.

The control unit for devNum cannot be used.

Perform a refresh on the storage subsystem to obtain the latest configuration information, and check the specified WWN.

An attempt to add a logical unit has failed.

The cu number is not valid. Perform a refresh on the storage subsystem to obtain the latest configuration information.

LDEV cannot be created because the SSID is not set.

You need to set an appropriate SSID from

SVP. Contact the subsystem administrator, or call maintenance personnel.

The specified capacity is invalid. Specify a valid capacity, and then retry.

The setting value of the security option of Storage array has changed. A refresh of the storage subsystem is recommended. Contact your system administrator if you are a local user.

This API version does not support the LUN Management option.

The Device Manager Server may not contain the most current storage device information.


Check this subsystem's option list.

Alternatively, check the Device Manager

Server XML API manual and make sure the running API version supports the command.

Specify a Fibre Channel port, and then retry. The request cannot be processed because the specified port is not a Fibre Channel port.

The request cannot be processed because the security switch of the specified port is turned off.

Turn on the security switch of the port, and then retry.

The request cannot be processed because the port that the specified

HostStorageDomain belongs to is not a Fibre Channel port.

Specify a HostStorageDomain that belongs to a Fibre Channel port, and then retry.



1-33

1-34

Error Code

KAIC05719-E

KAIC05720-E

KAIC05721-E

KAIC05722-E

KAIC05723-E

KAIC05724-E

KAIC05725-E

KAIC05726-E

KAIC05727-E

KAIC05728-E

KAIC05729-E

KAIC05730-E


The request cannot be processed because the security switch of the port that the specified HostStorageDomain belongs to is turned off.

The specified

HostStorageDomain "HSD-

identifier" already exists on the port "port-identifier".

An inconsistency was detected for the storage array. A refresh of the storage subsystem is recommended. Contact your system administrator if you are a local user.

This operation to the subsystem has failed. Some of the operation may have been applied to the storage subsystem. A refresh of the storage subsystem is recommended. Contact your system administrator if you are a local user.

The LUN "LUN-of-a-path" was not found on the storage array.

The SCSI ID "SCSI-ID-of-a-

path" was not found on the storage array.

The LUN "LUN-of-a-path" is already used on the storage array.

The port "port-identifier" was not found on the storage array.

The HostStorageDomain "HSD-

identifier" does not exist on the port "port-identifier".

PDEV #"PDEV-ID" is not a spare drive.

The specification of nickname

"nickname" is invalid. The maximum length of the nickname is "maximum-length-

of-nickname" bytes.

An attempt to log in to the subsystem has failed. Password authentication is required.

Specify the user ID and password, and then try again.

Turn on the security switch of the port that the specified HostStorageDomain belongs to, and then retry.

Check the combination of the specified

HostStorageDomain and port ID.

The Device Manager Server may not contain the most current storage device information.




Center.

Check the LUN.

Check the SCSI ID.

Check the LUN.

Check the Port.

Check the HostStorageDomain.

Check the PDEV.

Check the specified nickname. Make sure that the nickname is correct, and then retry.

Specify the user ID and password, then retry. If this problem continues to occur, contact the Support Center.



Error Code

KAIC05731-E

KAIC05732-E

KAIC05735-E

KAIC05736-E

KAIC05737-E

KAIC05750-E

KAIC05751-E

KAIC05752-E

KAIC05760-E

KAIC05761-E

KAIC05762-E

KAIC05763-E

KAIC05764-E

KAIC05765-E


A LUSE Volume configuration is not supported when the devNum is specified with emulation type "emulation-

type" and a capacity of

"capacityKB". Specify the creation capacity within the range from "min-ldev-sizeKB" to "max-ldev-sizeKB".

An attempt to change portRole has failed.

An inconsistency was detected in the "type of information" information. Refreshing the storage subsystem is recommended. If you are a local user, contact your system administrator.

An LU cannot be created. The number of LUs that can be created using the specified parameter is "maximum

number of LUs".

An error occurred while deleting an LU. (successfully deleted device(s) : "device number

list")

The devNum cannot be used.

There are no SSIDs that Device

Manager can assign for the LU to be created.

The LUs cannot be created because their total capacity exceeds the free space in the array group.

The subsystem managed by the partitioned storage administrator cannot execute the request.

Make sure that the capacity falls within the valid range for the emulation type.

Confirm the state of the port, and then try again.

The Device Manager Server might not contain the most current storage device information. Refresh the storage subsystem, and then try again.

Make sure that there is sufficient free space at the target, or revise the LU capacity and count. For details, see the manual that corresponds to your storage subsystem.

Revise the devNum (device number) value, and then try again.

The specified operation cannot be executed because the PDEV of the specified disk capacity

"disk-capacity" is not supported.

Revise the specification for devNum of the

LogicalUnit elements and then try again.

Check and, if necessary, specify a different disk capacity, and then retry the operation.

The specified drive type "drive-

type" is invalid.

The specified CLPR "CLPR-

number" does not exist in the storage subsystem.

Check and, if necessary, specify a different drive type, and then retry the operation.

Revise the CLPR specification.

The specified capacity is invalid. Revise the LU or LDEV capacity specification.


"device-number" is not available.

Revise the device number specification.

Revise the "server.properties" value, and then restart the services.

Reduce the total capacity of the LUs to be created, and then retry the operation.

Revise the subsystem settings.



1-35

1-36

Error Code

KAIC05766-E

KAIC05767-E

KAIC05768-E

KAIC05769-E

KAIC05770-E

KAIC05771-E

KAIC05772-E

KAIC05773-E

KAIC05774-E

KAIC05779-E

KAIC05780-E

Description

There is no PP Name (Dynamic

Provisioning) volume group which Device Manager can assign.

There is no CU which Device

Manager can assign.

The pool threshold cannot be modified to the specified value

"threshold" because it is less than or equal to the pool's usage rate "pool's usage rate".

Status in pool (function="PP

Name (Dynamic Provisioning)" pool ID="poolID") is not

"Normal", and threshold of pool cannot be modified.

This API cannot be executed because it has supported it since the microcode version 7.

The retention term of the specified LDEV has not expired.

The protection attributes of the specified LDEV cannot be changed.

Usage rate of pool

(function="PP Name (Dynamic

Provisioning)" pool

ID="poolID") is more than

95%, and threshold of pool cannot be modified.

The pool cannot be created because the maximum number of pools for "PP Name (Quick

Shadow)" or "PP Name

(Dynamic Provisioning)" have been created in the storage subsystem.

Array groups cannot be added because the number of array groups for "PP Name (Dynamic

Provisioning)", "PP Name (Quick

Shadow)" and "PP Name

(Universal Volume Manager)" will exceed the maximum number of array groups in storage subsystem.

An attempt to execute the request failed. The array groups of the source and target volumes do not match in the

Device Manager database and the storage array.

The specified subsystem does not support the host mode

"name-of-host-mode".


Reduce the LUs to be added, and then retry the operation.

Create the volume to the existing CU.

Specify a value that is more than the pool's usage rate, and then retry the operation.

Check the status of specified pool, and then retry the operation.

Check the microcode version of the subsystem.

Check the specification of the LDEV.

Check the usage rate of pool.

Delete any unnecessary pool, and then retry the operation.

Delete any unnecessary array groups for "PP

Name (Dynamic Provisioning)", "PP Name

(Quick Shadow)" or "PP Name (Universal

Volume Manager)", and then retry the operation.

Refresh the storage subsystem, and make sure the request is correct.

Revise the subsystem specifications.



Error Code

KAIC05781-E

KAIC05782-E

KAIC05783-E

KAIC05784-E

KAIC05785-E

KAIC05786-E

KAIC05787-E

KAIC05788-E

KAIC05789-E

KAIC05790-E

KAIC05791-E

KAIC05792-E


The specified host mode "name-

of-host-mode" cannot be specified for the microcode version of this subsystem.

The specified port does not support the channel speed

"channel-speed".

The specified subsystem does not support the host mode 2

"name-of-host-mode-2".

The specified host mode 2

"name-of-host-mode-2" cannot be specified for the microcode version of this subsystem.

The specified subsystem does not support the option "name-

of-port-option".

The specified port option

"name-of-port-option" is not supported on the microcode version of this subsystem.

Storage subsystem information different from that of the actual machine is registered in Storage

Navigator Modular 2. Use

Storage Navigator Modular 2 to delete the following storage subsystem information, and then retry the operation. (array name = "array-name-

registered-in-Storage-

Navigator-Modular-2")

PP-Name functionality must be enabled on the subsystem.

The specified operation cannot be executed because the usage rate of the pool

(poolID="poolID", usage=

"pool-usage-rate") is the pool threshold (attribute-

name="attribute-value") or more.






Use Storage Navigator Modular 2 to delete the storage subsystem information, and then retry the operation.

Enable PP-Name functionality on the subsystem.

Revise the configuration so that the pool usage rate is less than the value of attribute-

name, and then retry the operation.

A pool/journal group cannot be created because the maximum number of PP Name (Universal

Replicator) pools/journal groups has been created in the storage subsystem.

A journal group cannot be shrunk because its status is not

"Initial" or "Stop".

A journal group cannot be expanded because its status is not "Initial", "Active", or "Stop".

Delete any unnecessary pools/journal groups, and then try again.

Change the status of the pairs that use the journal group, and then retry the operation.




1-37

1-38

Error Code

KAIC05793-E

KAIC05794-E

KAIC05795-E

KAIC05796-E

KAIC05798-E

KAIC05799-E

KAIC05800-E

KAIC05850-E

KAIC05851-E

KAIC05852-E

KAIC05853-E

KAIC05854-E


The specified pool cannot be deleted because its used capacity is not 0GB.

The Status of all pairs that use the specified pool must be

"Simplex".

SnapShot or TrueCopy

Extended Distance functionality must be enabled on the subsystem.

The LU "device number" cannot be used for a pool volume/journal volume because it is set for VMA.

The specified journal group cannot be deleted because its status is not the initial status.

An internal server error occurred. An attempt to execute the transport service failed because the parameter

"parameter" or "parameter" is missing.

An internal error occurred during execution of the CIM function.

On the port "port-name", security is not set for the host storage domain "host-storage-

domain-name" or the iSCSI initiator "iscsi-initiator-name".

On the port "port-name", security has already been set for the host storage domain

"host-storage-domain-name" and the iSCSI initiator "iscsi-

initiator-name".

For the specified port "port-

name", the maximum number of iSCSI names "maximum-

number-of-iscsi-initiators" has already been set or might be exceeded when the processing is executed.

The specified nickname

"nickname" is already being used for another iSCSI name on the same port "port-name".

The specified iSCSI name "iscsi-

name" is already being used by another host storage domain on the same port "port-name".

Delete all pairs which use the specified pool.

Change status of pairs which use the pool into "Simlex", and then retry.

Check and, if necessary, revise the subsystem functionality.

Revise the LU specification, and then try again.

Change the status of the journal group to the initial status, and then retry the operation.





Specify a nickname that is not being used by another iSCSI name on the same port, and then retry the operation.

Specify an iSCSI name that is not being used by another host storage domain on the same port, and then retry the operation.



Error Code

KAIC05855-E

KAIC05856-E

KAIC05857-E

KAIC05858-E

KAIC05859-E

KAIC05860-E

KAIC05861-E



"nickname" is already being used by another host storage domain on the same port "portname".

The maximum number of host storage domains "maximum-

number-of-iscsi-targets" for the port "port-name" cannot be exceeded.

The specified iSCSI name

"nickname" is invalid. The maximum length of the iSCSI name is "maximum-length-of-

nickname bytes".

The specified iSCSI name "iscsi-

name" is invalid. Specify the iSCSI name by using the iqn format or the eui format.

Different nickname "iscsi-

nickname1" and "iscsi-

nickname2" are specified for iSCSI name "iscsi-name" on same port "port-name".

An error occurred during access to an SMI-S Enabled subsystem. A specified parameter or the status of the

SMI-S provider or the SMI-S

Enabled subsystem might be invalid. (WBEM error code =

"WBEM-error- code", WBEM method name = "WBEM-

method-name", CIM class name

= "target-CIM-class-name", detailed information =

"detailed-information")

An attempt to access the SMI-S

Enabled provider has failed.

Make sure the following parameters are correct: SMI-S provider IP address, port number, user ID and password.

(WBEM error code = "WBEM-

error- code", WBEM method name = "WBEM-method-name",

CIM class name = "target-CIM-

class-name", detailed information = "detailed-

information")

Specify a nickname that is not being used by another host storage domain on the same port, and then retry the operation.

Revise the specification so the maximum number of host storage domains is not exceeded.

Revise the specified iSCSI name, and then retry the operation.



Check, and if necessary, revise the specified parameters. In addition, make sure the status of the SMI-S provider and the SMI-S

Enabled subsystem are correct. If this problem persists, contact the SMI-S provider administrator.

Make sure the following parameters are correct, and the try again: SMI-S provider IP address, port number, user ID and password.



1-39

1-40

Error Code

KAIC05862-E

KAIC05863-E

KAIC05864-E

KAIC05865-E

KAIC05866-E

KAIC05867-E

KAIC05868-E


The environment for the SMI-S

Enabled subsystem is invalid.





information")

An internal error occurred during access to an SMI-S

Enabled subsystem. (WBEM error code = "WBEM-error-

code", WBEM method name =

"WBEM-method-name", CIM class name = "target-CIM-


information")

An unexpected error occurred during access to an SMI-S





information")


Enabled subsystem. (CIM method name = "CIM-method-

name", return value = "value-

returned-from-the-CIM-

method")


Enabled subsystem. (CIM method name = "CIM-method-



method")

Communication between the

SMI-S provider and SMI-S

Enabled subsystem timed out.

(CIM method name = "CIM-

method-name", return value =

"value-returned-from-the-CIM-

method")

Execution of the access method of the SMI-S Enabled subsystem failed. (CIM method name = "CIM-method-name", return value = "value-returned-

from-the-CIM-method")




Contact the SMI-S provider administrator.






Error Code

KAIC05869-E

KAIC05870-E

KAIC05871-E

KAIC05872-E

KAIC05873-E

KAIC05874-E

KAIC05875-E

KAIC05876-E

KAIC05877-E

KAIC05878-E

KAIC05879-E


A parameter required for accessing an SMI-S Enabled subsystem is invalid. (CIM method name = "CIM-method

name")

An invalid value was returned from an SMI-S provider. (CIM method name = "CIM-method-



method")

The specified volume size is invalid. (CIM method name =

"CIM-method-name")

The specified LU ID (LUN) is invalid. (CIM method name =


The specified initiator port ID

(WWN) is invalid. (CIM method name = "CIM-method-name")

The specified target port ID

(WWN) is invalid. (CIM method name = "CIM-method-name")

The specified permission is invalid. (CIM method name =


The specified initiator port and target port combination is already exists. (CIM method name = "CIM-method-name")

The specified LUN is already in use. (CIM method name =


An internal error occurred in an

SMI-S Enabled subsystem. (CIM method name = "CIM-method-



method")




"WBEM-error-code", WBEM method name = "WBEM-

method-name", detailed information = "detailed-

information")

Revise the parameter specification, and then try again.


Revise the volume size specification, and then try again.

Revise the LU ID (LUN) specification, and then try again.

Revise the initiator port ID (WWN) specification, and then try again.

Revise the target port ID (WWN) specification, and then try again.

Revise the permission specification, and then try again.

Revise the initiator port and target port combination, and then try again.

Revise the LUN specification, and then try again.






1-41

1-42

Error Code

KAIC05880-E

KAIC05881-E

KAIC05882-E

KAIC05883-E

KAIC05884-E

KAIC05885-E

KAIC05886-E


An attempt to access an SMI-S provider has failed. Check the following parameters: SMI-S provider IP address, port number, user ID, and password.

(WBEM error code="WBEM-

error-code", WBEM method name="WBEM-method-name", detailed information =




(WBEM error code="WBEM-

error-code", WBEM method name="WBEM-method-name", detailed information =



Enabled subsystem. (WBEM error code="WBEM-error-code",

WBEM method name="WBEM-


information")


Enabled subsystem. (WBEM error code="WBEM-error-code",

WBEM method name="WBEM-


information")

A job for an SMI-S Enabled subsystem has failed. (job status = "job-status", detailed code = "detailed-code", detailed information = "detailed-

information")



Enabled subsystem might be invalid. (WBEM method name =


class-name")

The SMI-S Enabled subsystem being managed by the specified

SMI-S provider is already managed by another SMI-S provider.

Check the following parameters, and the try the operation again: SMI-S provider IP address, port number, user ID, and password.







Specify settings such that multiple SMI-S providers do not manage the same SMI-S

Enabled subsystem.



Error Code

KAIC05887-E

KAIC05888-E

KAIC05889-E

KAIC05890-E





"WBEM-error- code", WBEM method name = "WBEM-

method-name", CIM class name

= "target-CIM-class-name", detailed information =

"detailed-information", subsystem name = "subsystem-

name")

An attempt to access the SMI-S

Enabled provider has failed.

Make sure the following parameters are correct: SMI-S provider IP address, port number, user ID and password.





information", subsystem name

= "subsystem-name")


















Make sure the following parameters are correct, and the try again: SMI-S provider IP address, port number, user ID and password.





1-43

1-44

Error Code

KAIC05891-E

KAIC05900-E

KAIC05902-E

KAIC05903-E

KAIC05904-E

KAIC05905-E

KAIC05906-E

KAIC05907-E

KAIC05908-E

KAIC05909-E









The option of the specified journal group cannot be modified.

"Inflow Control" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Inflow Control" cannot be modified because the specified journal group is a restore journal group.

A pool volume cannot be added because the status of the pool whose function is "PP Name

(QuickShadow)" and whose pool

ID is "pool ID" is blocked unless the usage rate is 100%.

"Data Overflow Watch" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Data Overflow Watch" cannot be modified because the specified journal group is a restore journal group and has a mirror whose status is "status".

"Path Watch Time" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Path Watch Time" cannot be modified because the specified journal group is a restore journal group and has a mirror whose status is "status".

"Path Watch Time" cannot be modified because the specified journal group is a restore journal group.


Check and, if necessary, revise the journal group type.

Check and, if necessary, revise the journal group type and the mirror status.


Recover from the pool blocked status, and then retry the operation.





Error Code

KAIC05910-E

KAIC05911-E

KAIC05912-E

KAIC05913-E

KAIC05914-E

KAIC05915-E

KAIC05916-E

KAIC05917-E

KAIC05918-E

KAIC05919-E

KAIC05990-E

Description

"Forward Path Watch Time" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Forward Path Watch Time" cannot be modified because the specified journal group is a restore journal group.

"Use of Cache" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Use of Cache" cannot be modified because the specified journal group is a restore journal group and has a mirror whose status is "status".

"Speed of Line" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Speed of Line" cannot be modified because the specified journal group is a restore journal group and has a mirror whose status is "status".

"Delta resync Failure" cannot be modified because the specified journal group is a master journal group and has a mirror whose status is "status".

"Delta resync Failure" cannot be modified because the specified journal group is a restore journal group.

A pool volume cannot be added because the status of the pool whose function is "PP Name

(Dynamic Provisioning)" and whose pool ID is "poolID" is blocked.

Virtual volumes for "PP Name

(Quick Shadow)" virtual volumes cannot be created because the number of virtual volumes for "PP Name (Quick

Shadow)" has already reached the maximum allowed.


(detailed information =











Recover from the pool blocked status, and then retry the operation.

Revise the settings.




1-45

1-46

Error Code

KAIC05991-E

KAIC05992-E

KAIC05993-E

KAIC05994-E

KAIC05995-E

KAIC05996-E

KAIC05997-E

KAIC05998-E

KAIC05999-E

Description

An attempt to create a volume has failed. Check whether a required license for the SMI-S

Enabled subsystem is missing or whether a hardware error has occurred.

The request was not completed within the time limit. Only part of the changes made to the configuration might have been applied to the SMI-S Enabled subsystem.

There is no response from the connection destination (IP-

address).

An error occurred while accessing the virtualizationserver management program or virtualization server. This might be because a specified parameter is invalid, or the virtualization-server management program or virtualization server is not in a normal status.

An attempt to access the virtualization-server management program or virtualization server failed.

Confirm that the IP address, user ID, and password of the connection destination are correct.

The virtualization server environment is invalid.

An internal error occurred while accessing the virtualizationserver management program or virtualization server.

An unexpected error occurred while accessing the virtualization-server management program or virtualization server.

The virtualization servers managed by the specified connection destination are already managed by another virtualization-server management program. The virtualization-server management configuration might have been changed.


If this problem occurs again, contact the

SMI-S provider administrator.

Refresh the SMI-S Enabled subsystem, and then check the changed settings. If this problem occurs again, contact the SMI-S provider administrator.

Make sure that the IP address and connection protocol are correct, and then try again.

Revise the parameters settings, check the status of the virtualization-server management program and virtualization server, and then try again. If this problem persists, contact the Support Center.

Make sure that the IP address, user ID, and password of the connection destination are correct, and then try again.




Revise the virtualization-server management configuration.



Table 1-8 KAIC06000-KAIC06999: Storage Array Errors: SNMP, Etc.

Error Code

KAIC06000-E

KAIC06002-E

KAIC06003-E

KAIC06004-E

KAIC06005-E

KAIC06006-E

KAIC06007-E

KAIC06008-E

KAIC06009-E

KAIC06010-E

KAIC06011-E

KAIC06012-E

KAIC06013-E


An unspecified storage array error was encountered.

An unspecified error occurred while executing SNMP command.

An attempt to create the SNMP session on the device at IP

Address "IP-address or host-

name" has failed.

Error retrieving oid "oid" due to a null oid table.

An attempt to retrieve the object ID "oid" has failed.


An internal server error was encountered due to a failure in the SNMP library. Contact the

Support Center.

An internal server error was encountered due to a failure in the SNMP library. Contact the

Support Center.

An error occurred while accessing the device via SNMP. This indicates a network connection or SNMP configuration error on the device.

A null value for object ID "oid" was retrieved via SNMP.

An SNMP error of status

"status" occurred while waiting for the command "command" to complete.

Communication timed out waiting for a response from the array. Check the network connection.

The SNMP set request has failed to execute the command

"command". Error status =

"error-status", index = "index".

An invalid command status trap was detected.

SNMP authentication has failed for the device at IP Address

"IP-address".

The storage array cannot be accessed. An operation is in progress at the SVP.

The device at IP Address "IP-

address" was not identified as a family storage array. Check the IP address and SNMP agent configuration.

An internal server error was encountered in the command trap specification. Contact the

Support Center.

The Device Manager Server must have read/write permission to perform management functions on the storage device.

Check the SNMP community string and make sure that the read/write permissions are correct.

An attempt to access the storage device failed as the SVP is currently in "Modify" mode.

Device Manager Server must have exclusive access to the device to perform management functions.

Check the IP address and SNMP agent connection.



1-47

1-48

Error Code

KAIC06100-E

KAIC06101-E

KAIC06200-E

KAIC06299-E

KAIC06300-E

KAIC06301-E

KAIC06302-E

KAIC06303-E

KAIC06305-E

KAIC06306-E

KAIC06307-E


The SNMP command has failed

(command status =

"command-status", meaning =

"meaning"). Only part of the configuration change may have been applied. Refresh the subsystem. If you are a local user, contact the system administrator.

The SNMP command has failed.

Information is not available. A refresh of the storage subsystem is recommended.

Contact your system administrator if you are a local user.

The subsystem serial number is invalid.

An error occurred during processing on the subsystem

(DampErrorCode = "error-

code-of-DAMP",

TransErrorCode = "error-code-

of-DampTrans", message =

"error-message"). If the configuration was being changed, refresh the subsystem. If you are a local user, contact the system administrator.

The command has failed on the storage array.

The Target ID mode of the controller is not "M-TID, M-LUN

(mapping mode)".

Refer to the applicable storage subsystem messages and recommended actions in this manual. Follow the recommended actions.

Perform a refresh on the storage array, and then retry.




Device Manager only supports the Target ID mode "M-TID, M-LUN (mapping mode)". For details about the Target ID mode, see the

Disk Array Management Program manual or

Storage Navigator Modular manual.

Contact the Support Center. An attempt to retrieve fibre channel port information for controller "controller-ID" has failed.

An attempt to retrieve the fibre channel port information for port "port-name" has failed.

The LUN security option is not installed on the storage array.

Check the configuration of the storage device.

The LUN security option must be installed to perform this function.

The LUN security option is disabled on the storage array.

The LUN security cannot be modified, because the port is in HP mode.

To change the LUN security, disable the HP mode of the port.



Error Code

KAIC06309-E

KAIC06311-E

KAIC06312-E

KAIC06313-E

KAIC06314-E

KAIC06315-E

KAIC06316-E

KAIC06317-E

KAIC06318-E

KAIC06320-E

KAIC06321-E

KAIC06322-E

KAIC06323-E

KAIC06330-E

Description

The LUN "LUN" of the port

"port-name" is already reserved for a non-existing

LDEV "device-number".

The integrated LU option is disabled on the storage array.

The integrated LU option is not installed on the storage array.


Device Manager does not support management of the specified LUN. Use Disk

Array Management Program or Storage

Navigator Modular to release the LUN.


The integration LU option must be enabled to perform this function.


The integration LU option must be installed to perform this function.

Contact the Support Center. An attempt to retrieve port information for controller

"controller-ID" has failed.

An attempt to retrieve port information for port "port-

name" has failed.

The host mode 2 "name-of-

host-mode-2" for fibre port is invalid.

The host mode 2 "name-of-

host-mode-2" for SCSI port is invalid.

The port option "port-option" for fibre port is invalid.

The port option "port-option" for SCSI port is invalid.

The subsystem does not support the host mode 2

"name-of-host-mode-2".

The target storage device is not in mapping mode.

This may indicate a configuration error on the storage device. Check the configuration of the storage device.


The request for the subsystem cannot be executed. The permission to manage the subsystem might have been acquired by another user.

The request for the subsystem cannot be executed. The login session of the subsystem has expired.

The specified subsystem

"array-family" is a SCSI model.

It is not supported in Device

Manager.

This operation requires that mapping mode be enabled. Check the device configuration. For details about the mapping mode, see the Disk

Array Management Program manual or

Storage Navigator Modular manual.

Make sure the storage array is not being accessed by the built-in account of another application. If it is not being accessed, refresh the subsystem, and then try again.

A forced logout might have been executed because the account was invalidated. Make sure such an operation was not executed performed on the subsystem by another user.

If no such operation was executed, refresh the subsystem, and then try again.

Check the subsystem.



1-49

1-50

Error Code

KAIC06400-E

KAIC06401-E

KAIC06402-E

KAIC06403-E

KAIC06450-E

KAIC06999-E

Description


(error code 1 = "error-code-1", error code 2 = "error-code-2", meaning = "meaning"). If the configuration was being changed, refresh the subsystem. If you are a local user, contact the system administrator.

An error occurred in the format processing of the subsystem.

(Error code = "Error Code")

Remove the cause of the problem, and then refresh the subsystem.

Processing in the subsystem has not finished. Remove the cause of the problem, and then refresh the subsystem.

LDEV (devNum="Device

number") is not in a formattable state.


(error code 1 = "error-code-1", error code 2 = "error-code-2", meaning = "meaning"). If the configuration was being changed, refresh both the subsystem and external subsystem. If you are a local user, contact the system administrator.

The SNMP command was cancelled after repeated failures.



Remove the cause of the problem, and then refresh the subsystem.

Refresh the subsystem, and then revise the

LDEV state.

Take action based on the applicable storage subsystem messages and recommended actions in the Device Manager error manual.


Table 1-9 KAIC07000-KAIC08999: Command (Agent) Errors

Error Code

KAIC07000-E

KAIC07001-E

KAIC07002-E

KAIC07003-E

KAIC07004-E

Description

Unspecified agent error was encountered.

Device Manager does not support the operation

"operation" for the storage array type.

The license key required for the operation is not installed.

The license key required for the operation is not active.

Invalid "LU" parameter.

Integer expected.



Device Manager Server does not support requests on the specified storage device.

Install the required license key.

Activate the required license key.

Make sure the "LU" is an integer value, and then retry. If this problem persists, contact the Support Center.



Error Code

KAIC07005-E

KAIC07006-E

KAIC07007-E

KAIC07008-E

KAIC07009-E

KAIC07010-E

KAIC07011-E

KAIC07012-E

KAIC07013-E

KAIC07014-E

KAIC07015-E

KAIC07016-E

KAIC07017-E

KAIC07018-E

KAIC07019-E

KAIC07020-E invalid.

Description

Missing parameter: Storage

Array "objectID".

Missing parameter: Port

"objectID".

Missing parameter: Path

"objectID".

Missing parameter: "WWN".

The value for the "scsiID" parameter is incorrect.

The specified WWN "WWN" is

Missing parameter:

WWNGroup "objectID".

Missing parameter: LUNGroup

"objectID".

The objectID references an incorrect object type for the request.

Missing parameter: Logical

Group "objectID".


The ObjectID parameter of Storage Array is required. Provide the missing parameter, and then retry.

The ObjectID parameter of the port is required. Provide the missing parameter, and then retry.

The ObjectID parameter of Path is required.

Provide the missing parameter, and then retry.

The WWN parameter is required. Provide the missing parameter, and then retry.

Check the SCSI ID. Make sure that the SCSI

ID is correct, and then retry. If this problem persists, contact the Support Center.

Make sure that the WWN parameter has the proper format.

ObjectID parameter of the WWNGroup is required. Provide the missing parameter, and then retry.

The ObjectID parameter of the LUNGroup is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

Check the type of the specified object.

Missing parameter: Host

"objectID".

Missing parameter: Logical

Group Element "objectID".

Missing parameter:

"objectID".

The specified logical group

("Logical-group-path") does not exist.

Missing parameter: Host

"name".

The ObjectID parameter of the Logical Group is required. Provide the missing parameter, and then retry.

The ObjectID parameter of the Host is required. Provide the missing parameter, and then retry.

The ObjectID parameter to be registered for the logical group as a logicalGroup element is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

The ObjectID parameter is required. Provide the missing parameter, and then retry.

Revise the parameter specifications.

A required element is missing from the request. "element"

The Name parameter of the Host is required.


Make sure that all of the required elements of a request are in place. Provide the missing element, and then retry. If this problem persists, contact the Support Center.



1-51

1-52

Error Code

KAIC07021-E

KAIC07022-E

KAIC07023-E

KAIC07024-E

KAIC07025-E

KAIC07026-E

KAIC07027-E

KAIC07028-E

KAIC07029-E

KAIC07030-E

KAIC07031-E

KAIC07032-E

KAIC07033-E

KAIC07034-E

KAIC07035-E

KAIC07036-E


There is more than one instance of the logical group

("Logical-group-path").

Specify the object ID.

Missing parameter: Host Info

"unspecified-parameter".

The logical group parent is invalid. A group cannot be its own parent.

The logical group parent is invalid. The request creates a circular group dependency.

The logical group parent was not found in the Device

Manager database.

The logical group was not found in the Device Manager database.

The storage array was not found in the Device Manager database.

The specified LDEV (devnum =

"Device number") cannot be found in the Device Manager database.

The specified path (port ID =

"Port ID", domain ID =

"Domain ID", devNum =

"Device number") cannot be found in the Device Manager database.

The host was not found in the


The host info was not found in the Device Manager database.

The "parameter-name" and

"parameter-name" parameters cannot be specified at the same time.

The number of elements specified in the request is invalid. (element = "element-

name")

Missing parameter: User

"loginID".

This operation cannot be executed because the maximum number of registerable RCUs or SSIDs has already been created.

Missing parameter: Rule

"ruleID".


Specify the object name not registered in the

Host Info.

Specify a logical group that is not also its own parent group.

The relationship between the logical group parent and logical group child is invalid. Check the specified group.

Check the logical group parent.

Check the logical group.

Check the coding of storage array.

Make sure that the specified LDEV is in the


Check and, if necessary, revise the path specification.

Check the host.

Check the host info.


Revise the number of elements in the request, and then try the operation again.

The User "loginID" is required. Provide the missing parameter, and then retry.

Delete any unnecessary RCUs or SSIDs, and then try again.

The Rule "ruleID" is required. Provide the missing parameter, and then retry.



Error Code

KAIC07037-E

KAIC07038-E

KAIC07039-E

KAIC07040-E

KAIC07041-E

KAIC07042-E

KAIC07043-E

KAIC07044-E

KAIC07045-E

KAIC07046-E

KAIC07047-E

KAIC07048-E

KAIC07049-E

KAIC07050-E

KAIC07051-E

Description

This operation cannot be executed because the maximum number of registerable logical paths has been exceeded.

Missing parameter: UserGroup

"name".

The user group was not found in the Device Manager database.


"password".


"groupName".

The user group name is invalid. Specify no more than

25 characters for the name, using only the following characters: a-z A-Z 0-9 - =

\ ` , . _

The user ID is invalid. Specify a user ID by using the following rules. Input rules :

"input-rules-for-user-ID"

The password is invalid.

Specify a password by using the following rules. Input rules: "input-rules-for-

passwords"

The specified group "specified-

logical-group-name" is not available because a child group with that name already exists under the group

"target-parent-logical-group-

name".

The specified group "specified-

logical-group-name" is not available because a top-level group with that name already exists.

A zero-length name is not permitted.

The file named "file-name" was not found.

The file named "file-name" cannot be read.

The MCU-RCU or remote path cannot be created between the specified storage subsystems.

Missing parameter: Debug level "value".


Delete any unnecessary logical paths, and then try again.

The UserGroup "name" is required. Provide the missing parameter, and then retry.

Check the user group.

The User "password" is required. Provide the missing parameter, and then retry.

The user "groupName" is required. Provide the missing parameter, and then retry.

Revise the entered user group name.

Revise the entered password.

Change the name of the child group, and then retry.

Change the group name, and then retry.

Revise the request, and then try again.


Revise the specification of the storage subsystem, and then try again.

The debug level "value" is required. Provide the missing parameter, and then retry.



1-53

1-54

Error Code

KAIC07052-E

KAIC07053-E

KAIC07054-E

KAIC07055-E

KAIC07056-E

KAIC07057-E

KAIC07058-E

KAIC07059-E

KAIC07060-E

KAIC07061-E

KAIC07062-E

KAIC07063-E

KAIC07064-E

KAIC07065-E

KAIC07066-E


The specified MCU port is not the Initiator.

The debug level value "debug-

level-value" is not valid.

An attempt to unregister

Subscriber "Subscriber-ID" has failed.

Missing parameter: Subscriber

"topic".

An attempt to register

Subscriber "Subscriber-ID" has failed.

Missing parameter: Network resource "IP Address".

The operation cannot be performed because the MCU-

RCU or remote path has already been created between the specified storage subsystems.

The "count" parameter is invalid, and needs to be a positive integer. This attribute should only be specified once.

This operation cannot be performed because the specified port is not in a modifiable combination.

The "start" parameter is invalid, and needs to be a date. This attribute should only be specified once.

Missing parameter: Object

"name".

Invalid parameter: Alert

"number" or "source" required.

The parent storage array could not be found.

Missing parameter: Storage device "arrayFamily".

This operation cannot be performed because the specified logical path is already registered for the

RCU.

Revise the specification of the logical path, and then try again.

Valid debug levels are 0 (All information) 1

(Informational messages and above) 2

(Warnings and above) 3 (Errors and above) 4

(Fatal errors only). Make sure that the "value" is valid, and then retry.

The specified Subscriber "Subscriber-ID" does not exist. Make sure that the "Subscriber-ID" is valid.

The topic of Subscriber is required. Provide the missing parameter, and then retry.


The "IP Address" is required. Provide the missing parameter, and then retry.

Revise the MCU-RCU or the remote path specification, and then try again.

Check the specified "count". Make sure that it is a positive integer, and then retry.

Revise the specification of the port, and then try again.

Check the specified "start". Make sure that it is a valid date, and then retry.

The object "name" is required. Provide the missing parameter, and then retry.

Both Alert "number" and "source" are required. Provide the missing parameters, and then retry. If this problem persists, contact the Support Center.

Check the description of storage array.

The "arrayFamily" of the storage device is required. Provide the missing parameter, and then retry.

Revise the specification of the path, and then try again.



Error Code

KAIC07067-E

KAIC07068-E

KAIC07069-E

KAIC07070-E

KAIC07071-E

KAIC07072-E

KAIC07073-E

KAIC07074-E

KAIC07075-E

KAIC07076-E

KAIC07077-E

KAIC07078-E

KAIC07079-E

KAIC07080-E

KAIC07081-E

KAIC07082-E

KAIC07083-E

Description

Missing parameter: Storage device "searchCommunity".

The "objectID" parameter is invalid.

The logical group can only contain objects from a single storage array.

The "Topic" parameter is invalid.

The parameter "name" exceeds the maximum possible length.

The specified logical paths are not set.

Invalid request target parameter: Expected

"expected-class-name"; found

"specified-class-name".


Controller "ID".


Controller "Mode".


Parameter "searchCommunity" of storage array is required. Provide the missing parameter, and then retry.

Make sure that the specified "objectID" is correct, and then retry.

An attempt was made to add an object to a logical group. However, a group can only contain objects from a single array.

Make sure that the specified "Topic" is correct, and then retry.

Make sure that the length of "name" does not exceed the maximum length, and then retry.



The value for Port Controller

Mode is invalid.

The requested mode cannot be set on a non-Fibre Channel

Port Controller.

The ports for the requested

Port Controller could not be found.

High Speed mode cannot be set because port "port1-ID" and port "port2-ID" have different host modes.

High Speed mode cannot be set because port "port1-ID" and port "port2-ID" have different topologies.

High Speed mode cannot be set because port "port1-ID" and port "port2-ID" have the same fibre address.

High Speed mode cannot be set because port "port-ID" topology is Point-To-Point.

The high speed mode cannot be set because LDEV "device-

number" is assigned to both port "port1-ID" and port

"port2-ID".

The Port Controller "ID" is required. Provide the missing parameter, and then retry.

The "Mode" of Port Controller is required.


Valid Port Controller value is required. See the

Device Manager Server XML API manual.

This request can only be attempted for a Fibre

Channel port.


High Speed mode requires that port "port1-

ID" and "port2-ID" have the same host mode.


ID" and "port2-ID" have the same topology.


ID" and "port2-ID" have the same fibre address.

High Speed mode requires that the topology of port "port-ID" be FC-AL.

Release the LDEV from one of the ports, and then retry the operation.



1-55

1-56

Error Code

KAIC07084-E

KAIC07085-E

KAIC07086-E

KAIC07087-E

KAIC07088-E

KAIC07089-E

KAIC07090-E

KAIC07091-E

KAIC07092-E

KAIC07093-E

KAIC07094-E

KAIC07095-E

KAIC07096-E

KAIC07097-E

KAIC07099-E

KAIC07100-E

KAIC07101-E

KAIC07102-E

KAIC07103-E

KAIC07104-E


The requested port has no

WWN.

Insufficient number of physical devices for array group.

The requested host mode is not available on this storage array.


"operation".


"ruleType".


"target".

Check the WWN of port.

The creation of an array group requires at least two physical devices.

Check the host mode or storage array.

Rule "operation" is required. Provide the missing parameter, and then retry.

Rule "ruleType" is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

Rule "target" is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

"group name" is required. Specify the missing parameter, and then retry.

A parameter is missing:

"group name" must be specified.


"role".

The role is invalid.

An invalid cluster number has been specified for the Port

Controller.

High speed mode is unavailable.

Invalid CHA number.

Invalid topology number.

Invalid fibre address.

Invalid channel speed.

The parameter "portID" is out of range. The valid range is

"minimum-port-ID" to

"maximum-port-ID".

The parameter "LU" is out of range. The valid range is

"minimum-LU" to "maximum-

LU".

The parameter "lun" is out of range. The valid range is

"minimum-lun(hex)

(minimum-lun)" to

"maximum-lun(hex)

(maximum-lun)".

The port was not found on the storage array.

The LU "device-number" was not found on the storage array.

User "role" is required. Provide the missing parameter, and then retry.

Check the role of user.

Check the number of the Port Controller.

High Speed mode is unsupported with the specified Port Controller.

Assign a valid card number.

Assign a valid topology.

Assign a valid fibre address.

Assign a valid channel speed.

Specify a valid value.

Check the specified port and storage array.

Check the specified LU and storage array.



Error Code

KAIC07105-E

KAIC07106-E

KAIC07107-E

KAIC07108-E

KAIC07109-E

KAIC07110-E

KAIC07111-E

KAIC07112-E

KAIC07113-E

KAIC07114-E

KAIC07115-E

KAIC07116-E

KAIC07117-E

KAIC07118-E

KAIC07119-E

Description

The LUN "LUN" was not found on the storage array.

The LU "device-number" is already in use on port "port-

name".

The LUN "LUN" is already in use on port "port-name".

The LU "device-number" is an

OnDemand device and cannot be used for an LUN.

This command cannot be processed, since both a

"devNum" attribute of a Path element and LDEV elements are not specified.

The LUN cannot be deleted, because one or more hosts are using it. LUN Security must be removed for this LUN before the path can be deleted.

The WWN "WWN" cannot be deleted. The WWN was not found on the port.

The port (portID = "Port ID") cannot be found in the storage subsystem.

The number of logical paths cannot go below the set minimum number of paths.

The security for this LUN cannot be changed, since it is part of LUNGroup "LUN-group-

nickname".

The LUN cannot be deleted, since it is part of LUNGroup

"LUN-group-nickname".

The specified remote paths are invalid. One port from both controller0 and controller1 must be specified.

The command cannot be executed because the specified WWN group is not on the port "port-name".

The command cannot be executed because the specified LUN group is not on the port "port-name".

The LUN referenced by the

HostInfo was not found in the storage array.


Check the specified LUN and storage array.

Check the LU.

Check the specified LUN.

Check the specified LU.

Check the request.

Clear the LUN security for this LUN, and then retry.

Make sure that the WWN and LUN are specified correctly. Otherwise, no action is required.

Check and, if necessary, revise the port or storage subsystem specification.


Delete the LUNGroup, and reissue the secure

LUN command.

Delete the LUNGroup, and then retry.

Revise the specification of the remote path, and then try again.

Make sure that the correct WWN group and port are specified, and then try again.

Make sure that the correct LUN group and port are specified.

Check the LUN.



1-57

1-58

Error Code

KAIC07120-E

KAIC07121-E

KAIC07122-E

KAIC07123-E

KAIC07124-E

KAIC07125-E

KAIC07126-E

KAIC07127-E

KAIC07128-E

KAIC07129-E

KAIC07130-E

KAIC07131-E

KAIC07132-E

KAIC07133-E

KAIC07134-E

Description

The specified host ("host-

name-or-objectID") does not exist.

The logical group element cannot be deleted, because the element is not part of the

Logical group.

The host name "host-name" is already used by an existing host.

The host info record is already contained in the Device

Manager database.

The storage array with serial number "serial-number" was not found in the Device

Manager database.

Cannot delete host "host-

name", because one of the

WWNs is securing an LUN.

The LDEV "device-number" is a "PP Name

(VolumeMigration)" reserved volume and cannot be used for an LUN.

Invalid parameter: Filter

"Condition volumeKind"



Check the specified objectID.

Specify a new host name.

Check the HostInfo.

Check the specified objectID of the storage array.

Clear the LUN before deleting the host.

Check the LDEV.

The logical unit with LU

"device-number" is a command device. The LUN cannot be deleted.

The WWN

"00.00.00.00.00.00.00.00" is invalid, and cannot be used to secure an LUN.

An LUN cannot be added to a port of type "port-type".

The SCSI ID "SCSI-ID" was not found on the storage array.

This operation cannot be performed for a port of the port type "port-type".

The maximum number of

WWNs ("maximum-number-

of-WWNs") cannot be exceeded.

The WWN "WWN" is already in use by host "host-name".

Make sure that the "Condition volumeKind" is valid. The valid Condition volumeKinds are

"MAINFRAME", "INTERMEDIATE", "OPEN" or combinations of these.

Check the LU.

Make sure that the WWN is correct.

Check the port.

Check the SCSI ID.

Check the port.

No more WWNs can be added to the port.

Delete WWNs that are not used, and then retry.

Check the specified WWN.



Error Code

KAIC07135-E

KAIC07136-E

KAIC07137-E

KAIC07138-E

KAIC07139-E

KAIC07140-E

KAIC07141-E

KAIC07142-E

KAIC07143-E

KAIC07144-E

KAIC07145-E

KAIC07146-E

KAIC07147-E

KAIC07148-E

Description

Physical device #"PDEV-ID" is already in use (role = "role").

Physical device #"PDEV-ID" is not on the proper chassis for the array group.

A logical unit that has an LUN defined cannot be deleted.

An array group that has an

LUN defined cannot be deleted.

Parameter "chassis" is out of range. The valid range is

"minimum-number-of-chassis" to "maximum-number-of-

chassis".

The Port Controller was not found in the Device Manager database.


LDEVs ("maximum-number-

of-LDEVs") for the array group cannot be exceeded.

An attempt to delete a spare drive has failed. The physical device #"PDEV-ID" is not a spare drive or is a spare drive which is currently being used.

The spare physical device

#"spare-physical-device-ID" must be deleted from the array group.

An invalid emulation type was specified.

An invalid capacity was specified for the desired emulation type.

Insufficient free space on the specified array group.


Check the PDEV "pdevID".

A PDEV with chassis specified as array groups is required.

The LUN must be deleted prior to deleting the logical unit.

The LUN must be deleted prior to deleting the array group.

Specify a valid "chassis" range in within the range "minimum-number-of-chassis" to

"maximum-number-of-chassis", and then retry.

Check the specified Port Controller.

Ensure that the number of LDEVs in the array group does not exceed the maximum, and then retry.

Check the specified PDEV.

Delete this array group to delete this spare physical device.

The emulation type specified is not supported by the operation. Device Manager Server can only create logical units using OPEN emulation.


Specify the size within the scope of free space.

For details, see the manual that corresponds to your storage subsystem.

Check the specified chassis. The maximum number of array groups ("maximum-

number-of-array-groups") for the chassis cannot be exceeded.

The parameter

"defaultPortController" is out of range. The valid range is

"minimum-controller-number" to "maximum-controller-

number".

Specify a "defaultPortController" within the range "minimum-controller-number" to

"maximum-controller-number", and then retry.



1-59

1-60

Error Code

KAIC07149-E

KAIC07150-E

KAIC07151-E

KAIC07152-E

KAIC07153-E

KAIC07154-E

KAIC07155-E

KAIC07156-E

KAIC07157-E

KAIC07158-E

KAIC07159-E

KAIC07160-E

KAIC07161-E

KAIC07162-E

Missing parameter: "host mode" in the ModifyPort request.

Description

Device Manager does not manage the specified Port

Controller "port-controller-ID".

Device Manager does not manage the specified port

"port-name".

Cannot find the specified storage array.

The parameter "domainID" is out of range. The valid range is "minimum-number-of-

domainID" to "maximum-

number-of-domainID".

The domainID "domainID" is already in use on port "port-

ID".


HostStorageDomains

("maximum-number-of-host-

storage-domains") for the port

"port-number" cannot be exceeded.

The host storage domain (port

ID = "Port ID", domainID =

"Domain ID") cannot be found in the Device Manager database.

Missing parameter:

HostStorageDomain

"objectID".


Check the specified Port Controller.

Check the specified port.

Check the specified storage array.

Specify a "domainID" within the range

"minimum-number-of-domainID" to

"maximum-number-of-domainID", and then retry.

Change the domainID.


Check and, if necessary, revise the host storage domain specification.

The HostStorageDomain "objectID" is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

The HostStorageDomain "host mode" is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

Check the specified objectID. "name" of the specified object cannot be deleted.

The partitioned storage administrator who manages this subsystem cannot modify the configuration of the port

(port ID = "Port ID") that belongs to SLPR: "SLPR-

Number".

The security for the LUN cannot be changed, because the WWN is part of

WWNGroup "WWNGroup".


"Condition type"

Missing parameter: "Port".

Check and, if necessary, revise the port specification.

Delete the WWNGroup, and reissue the secure/unsecure LUN command.

Revise the value you specified in Condition type. Valid values are ALL, FREE, ASSIGNED,

UNASSIGNED and RESERVED.

Port parameter required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.



Error Code

KAIC07163-E

KAIC07164-E

KAIC07165-E

KAIC07166-E

KAIC07167-E

KAIC07168-E

KAIC07169-E

KAIC07170-E

KAIC07171-E

KAIC07172-E

KAIC07173-E

KAIC07174-E

KAIC07175-E

KAIC07176-E


The specified port option is invalid.

The specified host mode 2 is invalid.

Inconsistent combinations of host modes are specified for the same port.

Inconsistent combinations of host mode 2 are specified for the same port.

XML Message has no API

Version for the URLLink.

The specified WWN does not exist on the target "target-

element".

This operation cannot be performed for a Port Controller of E-NAS.

The specified user ID is invalid.

The specified LU used by PP

Name (TrueCopy)/PP Name

(ShadowImage) cannot be deleted.

No more command devices can be added to the specified subsystem.

This operation cannot be performed for a system volume (devNum = "Device

number") of E-NAS.

For the specified emulation type "emulation-type", the creation capacity automatically computed from the specified size "specified-

size-in-KBKB" is "creation-

size-in-KBKB". Re-specify this value so that the creation capacity is within the range of

"lower-limit-size-in-KBKB" to

"upper-limit-size-in-KBKB".

Free space is insufficient on the specified array group.

Specify the size within the range of the free space. The automatically computed capacity for creation is

"creation-size-in-KBKB".

A Command Device without an

LUN defined cannot be added.


The specified storage subsystem does not support different combinations of host modes for the same port. Revise the settings.

The specified storage subsystem does not support different combinations of host mode 2 for the same port. Revise the settings.


Check the specified WWN, and then retry.

The operation is not supported for a Port

Controller of E-NAS.

Specify an effective user ID.

Check and, if necessary, revise the LU specification.

Up to 2 command devices can be specified.

Delete any unnecessary command device, and then retry.

The operation is not supported for an E-NAS system volume.


Specify the size within the range of free space.

Perform this operation after the definition of an LUN.



1-61

1-62

Error Code

KAIC07177-E

KAIC07178-E

KAIC07179-E

KAIC07180-E

KAIC07181-E

KAIC07182-E

KAIC07183-E

KAIC07184-E

KAIC07185-E

KAIC07186-E

KAIC07187-E

KAIC07188-E

KAIC07189-E


The last path of an LU

(devNum = "Device number") set for a command device cannot be deleted.

The specified command option is invalid.

Invalid parameters: domainID and WWN cannot be specified at the same time.

In LUSE creation, LDEV

"device-number" overlaps and is specified.

Missing parameter: LogicalUnit

"commandDevice".

Delete the command device, and then the path.

An invalid command option is specified.

Make sure that the request is correct.

Check the specification of LDEV.

The commandDevice parameter of LogicalUnit is required. Provide the missing parameter, and then retry. If this problem persists, contact the Support Center.

Check the LU. The LU "device-number" is a

PP Name (VolumeMigration) reserved volume, and cannot be used for a command device.

The LU "device-number" is a

LUSE device, and cannot be used for a command device.

The specified LU "device-

number" cannot be used as a

Command Device because it is being used by PP Name

(TrueCopy)/PP Name

(ShadowImage).


(devNum = "Device number") used by PP Name



To create a command device, the size of specified LU must be "minimum size of LU which

can create a command device"

KB or more.

If the specified path is not a representative LDEV configuring a LUSE, the path cannot be deleted.



Check the LU.

Use Disk Array Management Program or

Storage Navigator Modular to delete the path that is not a representative LDEV configuring a

LUSE, and then use Device Manager to refresh the storage subsystem.


The path for an LU used by PP



Device Manager Server does not support the operation

"operation" for the specified

LDEV.

Device Manager Server supports the operation for only open volumes. Check the specified

LDEV.



Error Code

KAIC07190-E

KAIC07191-E

KAIC07192-E

KAIC07193-E

KAIC07194-E

KAIC07195-E

KAIC07196-E

KAIC07197-E

KAIC07198-E

KAIC07199-E

KAIC07200-E

KAIC07201-E

KAIC07202-E


This command cannot be processed, since the specified

LU is a command device.

This command cannot be processed, since the specified

LU in not a command device.

The parameter "element-

name" is insufficient. Either

"attribute-name-1" or

"attribute-name-2" must be specified.

This command cannot be processed, since command device security is already set for the specified LU.

This command cannot be processed, since command device security is not set for the specified LU.

A non-OPEN emulation

LogicalUnit cannot be set as a command device.

The LU "device-number" is already being used for "PP

Name (QuickShadow)"

"volume type of QuickShadow"

.

An array group cannot consist of PDEVs with different drive types.

A RAID0 array group cannot consist of PDEVs with specified drive types.

The specified object already exists in the logical group

"LogicalGroup name".

The request has failed: empty messageID in request.

Check the LU.

Check the parameter.

Check the LU.

Make sure that the PDEV specification is valid.

Revise the object specifications.

GetRequestStatus requires a valid messageID attribute. Add a valid messageID attribute to the request, and then retry.


An attempt to create an external array group has failed. The specified external storage subsystem is in the same storage subsystem.

The request has failed: messageID "message-ID" not found.

No data was found for message ID. This is most likely because the data was already retrieved. See if the Device Manager database has been updated with the results of the request (i.e. Add Storage Array).



1-63

1-64

Error Code

KAIC07203-E

KAIC07204-E

KAIC07205-E

KAIC07206-E

KAIC07207-E

KAIC07208-E

KAIC07209-E

KAIC07210-E

KAIC07211-E

KAIC07212-E

KAIC07213-E

KAIC07214-E


This command cannot be executed because a normal volume and a V-VOL of "PP

Name (QuickShadow)" are mixed in the specified LU

(devNum = "Device number" and devNum = "Device

number").

This command does not support the specified emulation type.

An invalid combination of path group IDs is specified.

For a remote command device, the parameter

"number of LU" cannot be specified for numOfLUs.

An attempt to create an external array group has failed because the combination of the specified port "port-name" and external storage subsystem port (WWN =

"port-WWN") is invalid.

An attempt to create an external array group has failed because the combination of the specified port "port-name" and external storage subsystem volume (LUN =

"LUN") is invalid.

The external volumes for alternate paths are different.

The replication group is already registered in the


The request failed, since a null objectID exists in

ReplicationGroup.

An attempt to execute the request has failed. The object specified in ReplicationGroup was not found in the database.

The request failed, since a null objectID exists in

ReplicationInfo.

An attempt to execute the request has failed. The object specified in ReplicationInfo was not found in the database.


Specifiy "OPEN-V" as the emulation type.


Revise the specifications for the port and external storage subsystem port.

Revise the specifications for the port and external storage subsystem volume.

Revise the alternate paths specification.

Check the ReplicationGroup.

"api-name" requires a valid objectID attribute in the ReplicationGroup. Add an objectID to the request, and then retry.


"api-name" requires a valid objectID attribute in the ReplicationInfo. Add an objectID to the request, and then retry.




Error Code

KAIC07215-E

KAIC07216-E

KAIC07217-E

KAIC07218-E

KAIC07219-E

KAIC07220-E

KAIC07221-E

KAIC07222-E

KAIC07223-E

KAIC07224-E

KAIC07225-E

KAIC07226-E


The request failed, since the specified ReplicationGroup is not handled by Device

Manager.

The request failed, since the specified ReplicationInfo is not in the specified

ReplicationGroup.

The specified command option is invalid. The number of specified command option items is "number-of-specified-

option-items", but the API requires at least "minimum-

items-api-requires".

The specified command option is invalid. The number of specified command option items is "number-of-specified-

option-items", but the API requires at most "maximum-

items-api-demands".

The request failed, since the specified copyTrackSize "copy-

track-size" is invalid.

The replication controller pair was not found in the Device

Manager database.

The specified logical unit

(array type = "type-of-LU", serial number = "LU-serial-

number", device number =

"LU-device-number") cannot be used in a pair because the host's I/O suppression mode is enabled.

The specified LU "device

number" cannot be used for a

LUSE device because it is being used by PP Name


(ShadowImage).

The LUSE cannot be deleted because the specified LU

"device number" is used by PP


(ShadowImage).

The specified host mode option is invalid.

The object ID of the host is not specified.

The specified object ID of the host is invalid.

Check the property file of the corresponding host agent.

Check the request, and then retry.

Check what is specifies for the replication controller pair.

Revise the logical unit specification.


Revise the host mode option specification.

Revise the request, and then retry.

Specify the object ID of a host that batchmanages pairs.



1-65

1-66

Error Code

KAIC07227-E

KAIC07228-E

KAIC07229-E

KAIC07230-E

KAIC07231-E

KAIC07232-E

KAIC07233-E

KAIC07234-E

KAIC07235-E

KAIC07236-E

KAIC07237-E

KAIC07238-E

KAIC07239-E

KAIC07240-E


The object ID of "Element-

name" cannot be specified.

The specified

"replicationOwnerHost" was not found in the Device

Manager database.

The "Element-name" element is not specified.

The command cannot be executed because the specified LDEV "Device

number" is protected.

The command cannot be executed because a path is set for the specified LDEV "Device

number".


number" is set to a PP Name

(VolumeMigration) reserved volume.


number" is not a representative LDEV making up a LUSE Volume.


number" is a pair device.

The LDEV "Device number" specification is duplicated.


"Condition host"


Revise the LDEV specification.



Make sure that the "Condition host" is valid.

The valid Condition hosts are "ASSIGNED" and

"UNASSIGNED".

Revise the specifications for the logical unit. Multiple instances of the same logical unit "Device number" have been specified.

It is not possible to create an unformatted logical unit in the specified subsystem.

A Quick Format cannot be executed because there is no

System Disk area.

This command cannot be executed, because the specified LU is being used as a remote command device in another subsystem.

Revise the subsystem specification.

Create the System Disk area, and then try again.




Error Code

KAIC07241-E

KAIC07242-E

KAIC07243-E

KAIC07244-E

KAIC07245-E

KAIC07246-E

KAIC07247-E

KAIC07248-E

KAIC07249-E

KAIC07250-E

KAIC07251-E

KAIC07252-E

KAIC07253-E



number" was being used for

PP Name (Dynamic

Provisioning).

The LDEV "device-number" is a command device. The LDEV cannot be deleted.

The LU "device-number" cannot be formatted because it is an external volume, pool volume, or journal volume.

The wait option and quickformat option cannot be specified at the same time.

The specified external volume is a command device. When specifying the capacity of the

LU, you need to specify the same capacity as the external volume.

An attempt to create an external array group has failed because two or more combinations of the port

"port-name" and external storage subsystem port (WWN

= "port-WWN") are specified.

This operation cannot be performed for a port whose port role is "port-role".

The specified external volume is a command device. Mapping to an internal volume is required.

The cache mode cannot be set for a remote command device.

The LDEV related to the specified PP Name

(VolumeMigration) migration plan was not found in the


The specified "parameter-

name" was not found in the


LUSE is set for the specified

LDEV. The LDEV cannot be used for a PP Name


The specified VolumeMigration element objectID is invalid.


Check the LDEV.

Check the specified LU, and then try again.

Check the request, and then try again.


Revise the specifications for the port and external storage subsystem port.

Revise the port specification.




Revise the parameter specification.


Revise the objectID specification.



1-67

1-68

Error Code

KAIC07254-E

KAIC07255-E

KAIC07256-E

KAIC07257-E

KAIC07258-E

KAIC07259-E

KAIC07260-E

KAIC07261-E

KAIC07262-E

KAIC07263-E

KAIC07264-E

Description

A path is set for the specified

LDEV. The LDEV cannot be used for a PP Name


The specified LDEV is a command device. It cannot be used for a PP Name


The specified LDEV is already set as a PP Name


The specified LDEV is not PP

Name (VolumeMigration) reserved volume.

An attempt to execute the request has failed. A set or release operation for the PP

Name (VolumeMigration) reserved volume cannot be specified simultaneously.


(VolumeMigration) migration plan is not in the subsystem

("Array type", "Serial

number").

An attempt to execute the request has failed. The same ownerID must be specified for all VolumeMigration elements.

Invalid parameters were specified. The same sourceDevNum

"sourceDevNum of volume

migration" was specified for two or more VolumeMigration elements in the request.

Invalid parameters were specified. The same targetDevNum "targetDevNum

of volume migration" was specified for two or more

VolumeMigration elements in the request.

The owner ID specified in the request does not match the owner ID of the target volume.

An attempt to execute the request has failed. The ownerID must be specified in the VolumeMigration element.



Unify the specification of the reserved volume.

Check and, if necessary, revise the request.

Revise the ownerID specification, and then retry.

Revise the sourceDevNum specification for the

VolumeMigration elements, and then retry.

Revise the targetDevNum specification for the

VolumeMigration elements, and then retry.

Check the owner ID specifications.

Specify the same value as the ownerID of the target volume related to the VolumeMigration element.



Error Code

KAIC07265-E

KAIC07266-E

KAIC07267-E

KAIC07268-E

KAIC07269-E

KAIC07270-E

KAIC07271-E

KAIC07272-E

KAIC07273-E

KAIC07274-E

KAIC07275-E

Description

An attempt to execute the request has failed. The emulation types of the specified source and target volumes do not match.

An attempt to execute the request has failed. The size of the specified source and target volumes do not match.

An attempt to execute the request has failed. The specified volume is a pair consisting of a standard volume and a CVS volume.

An attempt to execute the request has failed. Specify the same hihsmOwnerID for all

LDEVs.

The specified LDEV is protected. It cannot be used for a PP Name


An attempt to execute the request has failed. The specified LDEV is a pair device. It cannot be used for a

PP Name (VolumeMigration) reserved volume.

An attempt to execute the request has failed. The parameter "Attribute name" is outside the valid range. The valid range is from "Min.

parameter value" to "Max.

parameter value".

The specified LDEV cannot be used because it is set for

ChacheResidency.

The parameter is invalid.

(Filter "Condition hostType")

The object ID of the host or the host name cannot be specified at the same time as the filter used for selecting the host.

The specified LDEV is being used for PP Name (Dynamic

Provisioning), and cannot be used for PP Name

(VolumeMigration).


For the source and target volumes, specify volumes that have the same emulation type.

For the source and target volumes, specify volumes that are of the same size.

Specify standard volumes or CVS volumes for the source and target volumes.

Revise the hihsmOwnerID specification, and then retry.




Revise the specification, then retry.




1-69

1-70

Error Code

KAIC07276-E

KAIC07277-E

KAIC07278-E

KAIC07279-E

KAIC07280-E

KAIC07281-E

KAIC07282-E

KAIC07283-E

KAIC07284-E

KAIC07285-E

KAIC07286-E

KAIC07288-E

KAIC07289-E

Description

The path cannot be set because the specified LDEV

"Device number" is being used in the pool of PP Name

(Dynamic Provisioning).

A PP Name (Dynamic

Provisioning) volume cannot be deleted in Device Manager.

A parameter is not specified.

("parameter")

The specified user ID or password is too long. This user ID and password cannot be used to access the SMI-S provider from Device

Manager. Specify a user ID and password by using 1024 bytes or fewer, and then try again.

The specified LDEV has a different logical DKC. The system cannot create the

LUSE. (devNum = "Device

number")

A parameter is invalid. (Filter:

"Condition portType")

The P-VOL's pool ID does not match the S-VOL's pool ID.

The specified pool does not exist in the Device Manager database.

An attempt to execute the request has failed. All replication pairs in the same replication group must use the same Pool.

A parameter is invalid.

(parameter = "parameter")

This operation cannot be performed because the command device is not specified.

This operation cannot be performed because the specified ports are not Fibre

Channel ports.

This operation cannot be performed because the specified ports are not SLPR:0 ports.


Make sure the LDEV specifications are correct.

Revise the LogicalUnit specification.

Revise the specification, and then try again.

Specify a valid user ID and password, and then try again.


Revise the specification, and then retry the operation.

Revise the pool ID specification.

Revise the pool specification.



Specify the command device, and then try again.

Revise the specification of the ports



Error Code

KAIC07290-E

KAIC07291-E

KAIC07292-E

KAIC07293-E

KAIC07294-E

KAIC07295-E

KAIC07296-E

KAIC07297-E

KAIC07298-E

KAIC07299-E


This command cannot be executed because the specified LDEV "device-

number" is being used by a pool of "PP-name (Dynamic

Provisioning)".

No more DM-LUs can be added to the specified subsystem.

This operation cannot be performed because the specified LU size, "LU-size"

GB, is insufficient.

This operation cannot be performed because the specified LU is not set as a

DM-LU.

The specified LU is not in the


This operation cannot be performed because the specified remote path does not use a Fibre Channel connection.

The executed command cannot use the specified volume "Device number".


Delete any unnecessary DM-LUs

Revise the specification of the LU

Revise the remote path specification, and then try again.

Device Manager cannot be used to perform operations on the specified pair or pairs.

This operation cannot be performed because the specified LU is already set as a

DM-LU.

The serial number of the specified subsystem (IP address = "IP-address") does not match the serial number registered in Device Manager.

The serial number might have been changed during maintenance work. (registered serial number = "registered-

serial-number", current serial number = "current-serial-

number")

Device Manager does not support operations on High Availability Manager volumes or

External Storage Availability Manager volumes. Release the High Availability

Manager or External Storage Availability

Manager configuration for the selected volume or select a different volume, and then retry the operation.

Device Manager does not support operations on High Availability Manager copy pairs or

External Storage Availability Manager copy pairs. Release the High Availability Manager or

External Storage Availability Manager configuration for the selected copy pair or select a different copy pair, and then retry the operation.

Revise the specification of the LU

Delete the target subsystem information from

Device Manager, and then re-add it.



1-71

1-72

Error Code

KAIC07300-E

KAIC07301-E

KAIC07302-E

KAIC07303-E

KAIC07304-E

KAIC07305-E

KAIC07306-E

KAIC07307-E

KAIC07308-E

KAIC07310-E

KAIC07311-E

KAIC07312-E

KAIC07313-E

KAIC07314-E

KAIC07315-E


A negative value is specified for the Messages timeToWait attribute.

The Subscriber is not registered.

Missing parameter in the

URLLink request.

The URLLink in the request does not exist.

The URLLink request contains both the objectID and linkedID parameters.

The objectID in the URLLink request does not reference a known storage array.

URLLink acquired from an

SMI-S Enabled subsystem cannot be deleted.

The object specified for linkedID cannot be found.

Device Manager does not support URLLink operations for specified Device Manager objects.

The host is not specified for performance data acquisition.

Specify the host for the property "server.cim.agent" in the "server.properties" file, restart Device Manager

Server, and the retry the operation.

Device Manager does not manage the specified host

"Host name".

The Port parameter and

LogicalUnit parameter cannot be specified at the same time.

Neither the Port parameter nor the LogicalUnit parameter is specified.

The specified storage subsystem does not support performance data acquisition, or the necessary microcode version is not installed.

The specified range of

LogicalUnit (from "Lower value

for LU range" to "Upper value

for LU range") is invalid.


Register the Subscriber by using

AddSubscriber in the XML-API.

Check the specified URLLink.

Revise the option and objectID specification.

Either objectID or linkedID must be specified, but not both.

Check the specified storage array.

Check the specified URLLink.

Revise the option and linkedID specification.

Revise the URLLink specification.

None.

Add the specified Host, and the retry.




Revise the specified parameters, and then retry the operation.



Error Code

KAIC07320-E

KAIC07321-E

KAIC07322-E

KAIC07323-E

KAIC07324-E

KAIC07325-E

KAIC07326-E

KAIC07327-E

KAIC07328-E

KAIC07331-E

KAIC07332-E

KAIC07333-E

KAIC07334-E

KAIC07335-E

KAIC07336-E


The specified subsystem is not supported the DF series

Performance retrieval function.

The specified label "label" is invalid because the maximum length for a label is maximum

label length bytes.

The specified label "label" is invalid because an empty string cannot be specified as a label.

The specified label "label" is invalid because it contains an invalid character.

The same LDEV is specified by more than one element.

The specified LDEV already has a label.

The targetID parameter of

ObjectLabel is missing.

Check the specified Parameter, and then retry.

Revise the label specification, and then try again.

The label parameter of

ObjectLabel is missing.

The specified LDEVs belong to more than one storage subsystem.

The host storage domain

(portID = " port ID", domainNickname = " domain

nickname") cannot be found in the Device Manager database.

Invalid parameters: domainID and domainNickname cannot be specified at the same time.

Invalid parameters: domainNickname and WWN cannot be specified at the same time.

Invalid parameters: parameter and parameter cannot be specified at the same time.(element = element)

A required parameter is not specified. (element = element, parameter = parameter)

Invalid parameters were specified. The attribute

"parameter" of the element

"element" and element

"element" cannot be specified at the same time.

Revise the LDEV specification, and then try again.


The targetID parameter of ObjectLabel is required. Specify the missing parameter, and then try again.

The label parameter of ObjectLabel is required. Specify the missing parameter, and then try again.


Revise the host storage domain specification.

Check and, if necessary, revise the parameters.

Check and, if necessary, revise the parameters.



1-73

1-74

Error Code

KAIC07337-E

KAIC07350-E

KAIC07351-E

KAIC07352-E

KAIC07353-E

KAIC07354-E

KAIC07356-E

KAIC07357-E

KAIC07358-E

KAIC07359-E

KAIC07360-E

KAIC07361-E


The command option option-

name cannot be specified for hosts of the type host-type.

The LUSE Feature is not available for the storage array.

All the LDEVs that make up a

LUSE must have the same

"attribute-name". The requested "attribute-name" of the LDEVs is "value1"

(devNum = "Device number") and "value2" (devNum =

"Device number").

In this API version, LDEVs that constitute a LUSE cannot be specified in LUSE creation.

The specified LDEV "LDEV-

identifier (devNum)" is a reserved volume of PP Name

(VolumeMigration). This LDEV cannot be used in a LUSE.

The LDEV "LDEV-identifier

(devNum)" currently exists as an LUN. This LDEV cannot be used in a LUSE.

The number of LDEVs for the

LUSE (devNum = "Device

number") must be between

"minimum-number-of-LDEVs" and "maximum-number-of-

LDEVs".

Response data not found for

Transport Layer.

The specified LDEV "LDEV-

identifier (devNum)" is a RAID

0 LDEV. RAID 0 LDEVs cannot be used to create a LUSE.

The microcode version of the storage array is insufficient for the requested LUSE operation.

The microcode version is

"microcode-version".

The LUSE cannot be created because the specified LDEVs

(devNum = "Device number" and devNum = "Device

number") have different default controllers.

For Device Manager, the LDEV

"devNum-of-LDEV" must be the representative LDEV in

LUSE operations using the microcode "microcode-

version" of this subsystem.

Revise the specified host.

The storage array does not support LUSE functionality. Check the specified storage array.

For the LDEVs that make up a LUSE, specify

LDEVs that have the same "type".


Revise the specifications for the LDEVs that make up the LUSE, and then try again.

Revise the specifications for the LDEVs that make up the LUSE.

Revise the specified number of LDEVs to be created for the LUSE.



Check the version of the software contained in the storage subsystem.

Check and, if necessary, revise the specifications of the LDEVs that make up the

LUSE.




Error Code

KAIC07362-E

KAIC07363-E

KAIC07364-E

KAIC07365-E

KAIC07366-E

KAIC07367-E

KAIC07370-E

KAIC07380-E

KAIC07381-E

KAIC07390-E

KAIC07391-E

KAIC07400-E


The size of a created LUSE

(devNum = "Device number") must be less than "max-size-

of-LUSETB". The specified size is "size-of-LUSEKB".

A logical unit that has a LUSE defined cannot be deleted.

The LUSE must be deleted before deleting the logical unit.

The LUSE cannot be created because the emulation type of a specified LDEV (devNum =

"Device number") is not OPEN.

An attempt to delete pairs has failed.

The LUSE cannot be created because the drive types of the specified LDEVs (devNum =

"Device number"and devNum

= "Device number") are different.

The specified LDEV "Device

number" is being used for PP

Name (Dynamic Provisioning), and cannot be used for a

LUSE.

The specified subsystem

("array-type", "serial-number

(Secret)") is not an object of

Device Manager management.

Invalid parameter: "element",

"invalid-parameter"

Check and, if necessary, revise the specifications of the LDEVs that make up the

LUSE.

LUSE must be deleted before deleting LDEV.

Check and, if necessary, revise the LDEV specification.


Center.

Check and, if necessary, revise the specifications of the LDEVs.


This is an information message only. No additional action is required.

Check that all of the required parameters of the element are specified. If a parameter is missing, specify the missing parameter, and then retry. If this problem persists, contact the Support Center.

Check the value of the ConfigurationChange element's type attribute.

An invalid value was specified in the ConfigurationChange element's type attribute. "type

attribute"

The specified storage subsystem does not support secure communication.

An attempt to execute a request has failed. The specified communication protocol is invalid.

HiScan SetHostVolume agent encountered an error : "error-

details".






1-75

1-76

Error Code

KAIC07401-E

KAIC07410-E

KAIC07411-E

KAIC07412-E

KAIC07413-E

KAIC07414-E

KAIC07415-E

KAIC07416-E

KAIC07417-E

KAIC07420-E

KAIC07421-E

KAIC07422-E

KAIC07423-E

KAIC07424-E

Description

The host IP address could not be resolved.

The specified host "host-

name" cannot be deleted because the host type of that host is "External port".

The WWNs of the specified host "host-name" cannot be changed because the host type of that host is "External port".

The AddHostRefresh operation is not supported for a host whose host type is "host-

type".

The file server information

"the-information-attempted-

to-be-changed" cannot be changed.

WWNs cannot be added to a mainframe host.

The specified host type "host-

type" is invalid.

This API cannot modify information of the specified host "host-name".

The host "host-name" cannot be merged because its host type is host-type.

The host "host-name" does not have a WWN or iSCSI name.


Revise the host agent settings and the host environment. If the problem persists, contact the Support Center.

Retry. If this problem persists, contact the

Support Center.

An attempt to update the host information has failed.

Another operation that updates the host information is already being executed.


Another operation that sets up the host is being executed.


Another operation is accessing the host information.

The updating of the host information was interrupted.

Device Manager Server may be shutting down.

Check the Device Manager Server status, and then retry.

Revise the host specification.


Revise the host type specification.






Error Code

KAIC07425-E

KAIC07426-E

KAIC07433-E

KAIC07434-E

KAIC07435-E

KAIC07436-E

KAIC07440-E

KAIC07441-E

KAIC07450-E

KAIC07452-E

KAIC07453-E

KAIC07454-E

KAIC07456-E

Description

The host "host-name-or-

objectID" is specified more than once.

The same host is specified for the target and source hosts.

A host that is not a virtualization server was detected for the specified IP address (IP-address).

The AddHostRefresh command cannot be executed for virtualization servers in this

API version.

The information regarding the specified virtualization server is inconsistent. Refresh the virtualization server, and then retry the operation.

The specified virtualization server is currently being refreshed. Wait a while, and then retry the operation.

An internal server error was encountered. An attempt to create the replication information has failed.

An internal server error was encountered. The LogicalUnit that the host agent specifies was not found in the database.

An internal server error was encountered. An attempt to acquire LogicalUnit information that is P-VOL or

S-VOL has failed.

An internal server error was encountered. An attempt to acquire information to access the host agent has failed.

An internal server error was encountered. An error occurred during the search for host agent(s) that will be accessed. Port "port-number" does not exist.


An attempt to operate "open-

or-close" on host agent server

"URL-of-host-agent" has failed. The response from the host agent was "response-

from-host-agent".




Revise the host specification, and then try again.

Use a version of the API that supports the command.

Refresh the virtualization server, and then retry the operation.

Wait a while, and then retry the operation.


Perform a refresh on subsystem ("array-type",

"serial-number") or check the status of host agent.



Confirm the status of host agent. If there are no problems with the host agent, contact the

Support Center.



1-77

1-78

Error Code

KAIC07457-E

KAIC07458-E

KAIC07459-E

KAIC07460-E

KAIC07461-E

KAIC07462-E

KAIC07470-E

KAIC07471-E

KAIC07472-E

KAIC07473-E

KAIC07474-E

KAIC07475-E

Description

An error occurred during communicating with the host agent "URL-of-host-agent".


Check the host agent and the status of the network connection between Device Manager

Server and host agent. If this problem persists, contact the Support Center.

Contact the Support Center. An internal server error was encountered. An attempt to create a request to the host agent has failed. The POST request of HTTP cannot be performed.

An attempt to resolve the IP address of host agent Server has failed.

The accessed host "host-

name" is different from the host "host-name" registered in

Device Manager.

An attempt to execute a request for the host agent has failed. (error details = "error-

message")

The version of the host agent on host "host-name" is

"installed-version-host-agent".

However, version "required-

version" or later of the host agent is required to execute the service.

An attempt to execute the request has failed. Execute the request again.

An attempt to update the information for the displayed list has failed.

The storage subsystem information ("Subsystem-

name") is inconsistent.

Refresh the subsystem, and then try again.

The storage subsystem information ("Subsystem-

name") is being updated. Wait a while, and then perform the operation again.

The value of the "attribute-

name" parameter is outside the valid range from

"minimum-value" to

"maximum-value".

The sum of startElementNum and numOfElements is outside the valid range from


"maximum-value".

Check that the IP address of host agent is valid.

Check that the host name and the IP address of the host agent in Device Manager are valid.

Check the host agent and the status of the network connection between Device Manager

Server and host agent. If this problem persists, contact the Support Center.

Check the host agent on the host.


Center.


Wait a while, and then perform the operation again.




Error Code

KAIC07476-E

KAIC07477-E

KAIC07478-E

KAIC07479-E

KAIC07480-E

KAIC07481-E

KAIC07482-E

KAIC07483-E

Description

The "attribute-name" parameter is missing in the requested "element-name" element.

Memory for the Device

Manager server became insufficient while this operation was being performed.


Check whether the requested element has all the necessary parameters. If there are any missing parameters, specify them and then re-execute the command.

If the command you executed is Add, Modify, or Delete, take the following action:

(1) Use the following procedure to check the status of the operation:

1. Increase the memory heap size for the

Device Manager server.

2. If the command was executed for a storage subsystem or host, refresh the information of the storage subsystem or host.

3. Check the status of the operation.

(2) If necessary, perform the operation again.

If the command you executed is Get, take the following action:

(1) Use the following procedure to perform the operation again:

1. Restart the Device Manager server.

2. Do either of the following:

- Increase the memory heap size for the

Device Manager server, and then perform the operation again.

- Reduce the amount of information to be collected, and then perform the operation again.

Contact the Support Center. An internal error occurred while registering a temporary user for the storage subsystem.

The value of Over Provisioning

Percent Alert Notice is outside the valid range from


"maximum-value".

ISCSINames cannot be added to a mainframe host.


"ISCSIName" is invalid because it exceeds the maximum length maximum-

length-of-ISCSIName bytes.


"ISCSIName" is invalid because it contains an invalid character.

The portWWN and portISCSIName parameters are both specified in the request.



Revise the specified ISCSIName, and then retry the operation.

Specify either the portWWN or the portISCSIName parameter, but not both.



1-79

1-80

Error Code

KAIC07484-E

KAIC07485-E

KAIC07486-E

KAIC07487-E

KAIC07488-E

KAIC07489-E

KAIC07490-E

KAIC07491-E

KAIC07492-E

KAIC07493-E

KAIC07494-E

KAIC07496-E

KAIC07497-E

KAIC07498-E

Description

ISCSINames cannot be specified for this

HostStorageDomain because the port to which this

HostStorageDomain belongs is a Fibre Channel port.

The specified ISCSIName is invalid.

WorldWideNames cannot be specified for this

HostStorageDomain because the port to which this

HostStorageDomain belongs is an iSCSI port.

The specified domain type

"domain-type" is invalid.

ISCSINames are invalid on this storage subsystem.

The following parameter is not specified: ISCSIName

"iSCSIName".

The ISCSIName "ISCSIName" does not exist in the Device

Manager database.


"ISCSIName" cannot be used because it is already being used for another ISCSIName on the same

HostStorageDomain.

The Fibre Channel port attribute and the iSCSI port attribute cannot be specified at the same time.

The iSCSI port attribute cannot be specified for a Fibre

Channel port.

The Fibre Channel port attribute cannot be specified for an iSCSI port.

The ISCSIName of the specified host "host-name" cannot be changed because the host is on an external port.


"nickname" is invalid for the specified ISCSIName

"ISCSIName".

The ISCSIName "ISCSIName" is already being used by the host "host-name".


Specify a HostStorageDomain that belongs to an iSCSI port, and then retry the operation.


Specify a HostStorageDomain that belongs to a Fibre Channel port, and then retry the operation.

Revise the domain type specification.

Revise the storage subsystem specification.

Specify the ISCSIName, and then retry the operation.


Specify an ISCSIName that is not already being used on the same HostStorageDomain, and then retry the operation.




Revise the ISCSIName specification.



Error Code

KAIC07499-E

Description

The host "host-name" cannot be deleted because it includes an ISCSIName used for an

LUN.


Delete the LUN security, and then delete the host.



1-81

1-82

Error Code

KAIC07501-E

KAIC07502-E

KAIC07503-E

KAIC07504-E

KAIC07505-E

KAIC07506-E

KAIC07507-E

KAIC07510-E

KAIC07511-E

KAIC07512-E

KAIC07513-E

KAIC07514-E

KAIC07515-E

Description

An error occurred while the fabric information was being acquired.

An error occurred while the fabric information was being acquired.

Only one instance of this command can be executed at one time.

The LUN Management option of the specified storage subsystem is not enabled.

The host information in the

Device Manager database has been updated. Other update processing might have been executed while Host Scan was executing.

Host Scan was not executed because no target storage subsystem was found.

The host information in the

Device Manager database has been updated. Other update processing might have been executed while hosts were being merged.

The configuration of purchasable optional features on the storage subsystem might have changed.

No more users can be registered because the maximum number of users has already been registered in the specified storage subsystem.

A user ID that is the same as the temporary user ID is already registered in the storage subsystem.

The element-name (attribute-

name="attribute-value") is specified more than once.

The poolID "poolID" is already being used in the subsystem.

The element-name (attribute-

name="attribute-value") was not found in the Device

Manager database.



Wait a while, and then try again.

Check the option list of the storage subsystem.

Make sure that other update processing is not executing, and then retry Host Scan. If this problem persists, contact the Support Center.


Make sure that no other update processing is being executed, and then try to merge the hosts again. If this problem persists, contact the Support Center.


Delete unnecessary users from the storage subsystem, and then retry the operation.

Delete the already registered user ID from the storage subsystem, and then retry the operation.

Revise the element-name specification.

Revise the poolID specification, and then retry the operation.

Revise the element-name specification.



Error Code

KAIC07516-E

KAIC07517-E

KAIC07518-E

KAIC07519-E

KAIC07520-E

KAIC07521-E

KAIC07522-E

KAIC07523-E

KAIC07524-E

KAIC07525-E

KAIC07526-E

KAIC07527-E

KAIC07528-E


The specified operation cannot be executed because the value of the attribute attribute-name

(attribute-value) is the value of the attribute attribute-name

(attribute-value) or more.

The element-name specification is invalid. The drive types of all element-

names in one pool must be the same.

The specified operation cannot be executed because the status of the element-name

(attribute-name="attribute-

value") is status.

The capacity "capacity" is invalid. Specify a value from

minimum-value to maximum-

value.

The specified operation cannot be executed for an array group that consists of PP-

Name pool.

The RAID level "RAID-level" cannot be specified for this operation.

The combination of RAID level and the number of PDEVs is invalid.

The selected number of PDEVs does not match the pool combination (function="PP-

name", poolID = "poolID").

The command option "option-

name" has not been specified.

The specified command option

"option-name" is invalid.

Revise the attribute-name and attribute-name specifications, and then retry the operation.

Revise the element-name specification, and then retry the operation.

Recover the status of element-name, and then retry the operation.

Revise the capacity specification, and then retry the operation.

Revise the array group specification.

Revise the RAID level specification, and then retry the operation.

Revise the RAID level and the number of

PDEVs, and then retry the operation.

Revise the PDEV specification, and then retry the operation.

Specify the command option "option-name".

Check and, if necessary, specify a different command option, and then retry the operation.

Check and, if necessary, specify a different capacity, and then retry the operation.

The specified capacity of

element-name (attribute-

name="attribute-value") is invalid. Specify the capacity more than the current capacity.

The specified operation cannot be executed because the pool

(poolID="pool-ID") is blocked.

"option-name" has not been specified for command option

2.

Unblock the pool, and then retry the operation.

Specify "option-name" for command option 2.



1-83

1-84

Error Code

KAIC07529-E

KAIC07530-E

KAIC07531-E

KAIC07532-E

KAIC07533-E

KAIC07534-E

KAIC07550-E

KAIC07551-E

KAIC07552-E

KAIC07553-E

KAIC07554-E

KAIC07555-E


The specified operation cannot be executed because status in pool (poolID="pool-ID") is not

"Normal".

The Over Provisioning Warning

Threshold is outside the valid range. The valid range is from


value.

The Over Provisioning Limit

Threshold is outside the valid range. The valid range is from


value.

The Over Provisioning Percent of the specified pool "pool-ID" has already exceeded the

Over Provisioning Limit

Threshold.

Upon executing this command, the Over

Provisioning Percent of the specified pool "pool-ID" will exceed the Over Provisioning

Limit Threshold.

The specified operation cannot be executed because the Over

Provisioning Warning

Threshold (attribute-value) is greater than or equal to the

Over Provisioning Limit

Threshold (attribute-value).

The specified IPAddress

"IPAddress" cannot be used because it is already being used by another port.

The format of the specified

IPAddress "IPAddress" is invalid.


SubnetMask "SubnetMask" is invalid.


DefaultGateway

"DefaultGateway" is invalid.

The PortNumber specified for the port is invalid.

The keepAliveTime specified for the port is invalid.

Recover from the pool status, and then retry the operation.

Revise the Over Provisioning Warning

Threshold, and then try again.

Revise the Over Provisioning Limit Threshold, and then try again.

Revise the pool specification, and then retry the operation.

Revise the size and number of virtual volumes that will be created or changed, and then retry the operation.

Revise the Over Provisioning Warning

Threshold and the Over Provisioning Limit

Threshold, and then try again.

Specify an IPAddress that is not being used by another port, and then retry the operation.

Specify the IPAddress by using a valid format.

Specify the SubnetMask by using a valid format.

Specify the DefaultGateway by using a valid format.

Specify a valid PortNumber.

Specify a valid keepAliveTime.



Error Code

KAIC07556-E

KAIC07557-E

KAIC07558-E

KAIC07559-E

KAIC07560-E

KAIC07561-E

Description


"ISCSIName" cannot be used because it is already being used by another

HostStorageDomain on the same port.


ISCSINames ("maximum-

number-of-ISCSINames") has been exceeded.


"nickname" cannot be used because it is already being used by another ISCSIName on the same port.

Device Manager does not support operations on this storage subsystem. The minimum microcode version is

"version".

The iSCSI attribute cannot be specified for the Fibre Channel

HostInfo.

The Fibre Channel attribute cannot be specified for the iSCSI HostInfo.


Specify an ISCSIName that is not being used by another HostStorageDomains on the same port, and then retry the operation.

No more ISCSINames can be added to the specified port. Delete any unnecessary

ISCSINames, and then retry the operation.

Specify a nickname that is not being used by another ISCSIName on the same port, and then retry the operation.

To perform this operation, the microcode version must be updated.




1-85

1-86

Error Code

KAIC07570-E

KAIC07571-E

KAIC07572-E

KAIC07573-E

KAIC07574-E

KAIC07575-E

KAIC07577-E

KAIC07578-E

KAIC07579-E

KAIC07581-E

KAIC07582-E

KAIC07583-E

KAIC07584-E

KAIC07585-E


The LU "device number" cannot be used for a pool volume because it is an

OnDemand device.

The drive type of all LUs that make up the specified pool must be same.

A pool cannot be deleted because one or more V-VOLs exist.

The pool volumes of specified pool cannot be deleted.

A journal group cannot be changed or deleted, because it is used by Universal Replicator for Mainframe.

The specified LU is not a volume of the specified journal group.

"Data Overflow Watch Time" could not be set, because the value for Inflow Control is

"No".

The combination of values specified for "Path Watch

Time" and "Unit of Path Watch

Time" is invalid.

A journal volume cannot be deleted when the delta of the master journal group is

"Hold".

The LU "device number" cannot be used as a pool volume/journal volume because the I/O suppression mode is active.

The LU "device number" cannot be used as a pool volume/journal volume because it is a system volume.

Journal volumes cannot be emptied during journal volume deletion.

The specified journal group ID

"journal group ID" is already used on the storage subsystem by PP Name

(Universal Replicator).

Operations cannot be performed for the specified journal group because it does not have any volumes.


Revise the drive types of pool volumes, and then try again.

Delete all V-VOLs used by the specified pool, and then try again.

Check the subsystem functionality.

Specify a journal group that is not used by

Universal Replicator for Mainframe, and then try again.


Revise the journal group options, and then try again.

Revise the values of "Unit of Path Watch Time" and "Path Watch Time", and then try again.




Revise the LU specification, and then retry the operation.

Revise the journal group ID specification, and then try again.

Revise the journal group ID specification, and then try again.



Error Code

KAIC07586-E

KAIC07588-E

KAIC07589-E

KAIC07590-E

KAIC07591-E

KAIC07592-E

KAIC07593-E

KAIC07595-E

KAIC07596-E

KAIC07600-E

KAIC07601-E

Description

The specified pool ID "poolID" is an invalid value. The pool

ID must be "value 1" or "value

2".

When modifying a journal group, either a journal group option or an LU to be modified must be specified.

The specified pool/journal group cannot be added in this

API version.

The specified pool/journal group cannot be deleted in this API version.

The specified pool/journal group cannot be modified in this API version.

A parameter is invalid. If you specify "Path Watch Time" or

"Unit of Path Watch Time", you must specify both of them at the same time.

The specified pool is invalid.

An attempt to execute the request has failed. The emulation types of the specified volumes are a combination of "emulation

type1" and "emulation type2".

The storage subsystem information ("subsystem-

name") is incomplete. Refresh the subsystem, and then try again.

The "microcode-version" microcode version of the storage subsystem cannot be used for the "PP Name

(Dynamic Provisioning)" configuration.

Device Manager does not support the "operation" operation except for the "PP

Name (Dynamic Provisioning)" function. again.

Revise the function type, and then retry the operation.


Revise the pool ID specification, and then try


Make sure that the operation is supported in the specified API version.



Specify both "Path Watch Time" and "Unit of

Path Watch Time".

Revise the pool ID specification, and then try again.

For the source and target volumes, specify volumes that have the same emulation type.


Make sure the microcode version of the storage subsystem is correct.



1-87

1-88

Error Code

KAIC07602-E

KAIC07603-E

KAIC07604-E

KAIC07605-E

KAIC07606-E

KAIC07607-E

KAIC07608-E

KAIC07609-E

KAIC07610-E

KAIC07611-E


The LU cannot be used for a pool volume because the capacity of the LU "device-

number" is outside the valid range. The capacity of a pool volume must be "minimum-

value(KB)KB(minimum-

value(LBA)LBA)" or more.

The LU "device-number" cannot be used for a pool volume/journal volume because the LU is a LUSE devise.

The LU "device-number" cannot be used for a pool volume/journal volume because the LU has a path set.

The LU "device-number" cannot be used for a pool volume/journal volume because it is a reserved volume of "PP Name (Volume

Migration)".

The LU "device-number" cannot be used for a pool volume/journal volume because it is a "volume-

attribute" of "PP Name".

The LDEV "device-number" cannot be used for a pool volume/journal volume because its status is not

"Normal".

The LDEV "device-number" cannot be used for a pool volume/journal volume because it is protected.

All LDEVs that make up a pool/journal group for "PP

Name (Dynamic Provisioning)" must have the same CLPR.

LU "device-number", whose emulation type is "emulationtype", cannot be used for a pool volume/journal volume of

"PP Name (Dynamic

Provisioning)".

The LU "device-number" cannot be used for a pool volume/journal volume because it is a command devise.


Check the status of the LDEV, and then retry the operation.




Error Code

KAIC07612-E

KAIC07613-E

KAIC07614-E

KAIC07615-E

KAIC07616-E

KAIC07618-E

KAIC07620-E

KAIC07621-E

KAIC07622-E

KAIC07623-E

KAIC07624-E

KAIC07625-E

Description

The LU "device-number" cannot be used for a pool volume/journal volume because it is set for "PP Name

(Cache Residency)".

The pool volume/journal volume cannot be added because the number of LUs will exceed the maximum number of pool volume/journal volume that make up a pool for "PP Name

(Dynamic Provisioning)".

The specified threshold

"threshold" is invalid.

The specified pool ID "poolID" is already being used on the storage subsystem, for "PP

Name (Quick Shadow)" or "PP

Name (Dynamic

Provisioning)".

The specified poolID/journal group ID "pool ID/journal

group ID" is invalid. A pool ID

/journal group ID must be in the range from "minimum-

value" to "maximum-value".

The specified pool cannot be deleted because an LU is assigned to it.

The LU "device-number" is already assigned to a pool.

"volume-attribute" and the pool must have the same

CLPR.

An attempt to execute the request failed because the LU

"device-number" is unassigned to pool.

The LU "device-number" cannot be released from the pool because the LU has a path.

The LU "device-number" cannot be released from the pool because the LU is a LUSE volume.

The array group

(chassis="chassis" number="array-group-

number") already exists in the storage subsystem.



Reduce the number of specified LUs, and then retry the operation.

Specify a valid value, and then retry the operation.

Revise the pool ID specification, and then retry the operation.

Revise the pool ID/journal group ID specification, and then retry the operation.

Remove any assigned LUs from the pool, and then retry.


Revise the pool and volume combination, and then retry the operation.


Release any paths for the LU, and then retry the operation.

Release the LUSE, and then retry the operation.




1-89

1-90

Error Code

KAIC07626-E

KAIC07627-E

KAIC07629-E

KAIC07630-E

KAIC07631-E

KAIC07632-E

KAIC07633-E

KAIC07634-E

KAIC07635-E

KAIC07636-E

KAIC07637-E

KAIC07638-E

KAIC07639-E



"device-number" is already in use.

The LDEV cannot be added, because the number of LDEVs will exceed the maximum number of LDEVs in the array group.

An LU whose emulation type is

"emulation-type" cannot be added to "PP Name (Dynamic

Provisioning)".

The specified array group was not found in the Device

Manager database.



number") cannot be deleted because it contains at least one LDEV that is assigned to a pool.



number") cannot be deleted because it contains at least one LU that has a path.



number") cannot be deleted because it contains a LUSE volume.



number") cannot be deleted because it contains at least one protected LDEV.


"device-number" is invalid.

The LU "device-number" cannot be deleted because it is assigned to a pool.

The LU "device-number" cannot be deleted because it has a path.

The LU "device-number" cannot be deleted because it is a LUSE volume.

The LU "device-number" cannot be deleted because it is protected.

Revise the device number specification, and then retry the operation.

Reduce the number of specified volumes, and then retry the operation.

Correct the specified emulation type, and then retry the operation.

Revise the array group specification, and then retry the operation.

Specify the option "force", and then retry the operation.

Release the paths set for the LU, and then retry the operation.



Specify another device number, and then retry the operation.

Specify the option "force", and then retry the operation.

Release the paths set for the LU, and then retry the operation.





Error Code

KAIC07640-E

KAIC07641-E

KAIC07642-E

KAIC07643-E

KAIC07644-E

KAIC07647-E

KAIC07648-E

KAIC07649-E

KAIC07650-E

KAIC07651-E

KAIC07700-E

KAIC07701-E

KAIC07702-E

KAIC07703-E

Description

A parameter is not specified :

LU "emulation"


LU "dpPoolID"


LU "threshold"

All LUs that make up a pool for "PP Name (Dynamic

Provisioning)" must have the same volume classes (internal or external).

All LUs that make up a pool for "PP Name (Dynamic

Provisioning)" must have the same cache mode.

The objectID of the array group is not specified. If you specify "exist" option, you must also specify the objectID of the array group.



number") is not used for "PP

Name (Dynamic

Provisioning)".

Specified LU

(devNum="device-number") is not "volume-attribute" of "PP

Name".

An error occurred in

Provisioning Manager Server.

(Message ID:Message-ID)

An error occurred when

Provisioning Manager Server was invoked.

In the "operation" operation, an array group and LU cannot be specified at the same time.

"option-name" cannot be specified for command option

2.

The value specified for

"option-name" of command option 2 is invalid.

The array group


number") have been specified more than once.


Specify the LU emulation type.

Specify the pool ID.

Specify the LU threshold.


Specify the objectID of the array group, and then retry the operation.

Specify an array group that is used for "PP

Name (Dynamic Provisioning)".

Specify volume-attribute of PP Name.

Refer to the Provisioning Manager Server log.

Specify either an array group or an LU, and then retry the operation.





1-91

1-92

Error Code

KAIC07704-E

KAIC07705-E

KAIC07706-E

KAIC07707-E

KAIC07708-E

KAIC07709-E

KAIC07710-E

KAIC07711-E

KAIC07712-E

KAIC07713-E

KAIC07714-E

KAIC07715-E

KAIC07716-E


The specified pool

(function="PP Name (Dynamic

Provisioning)" pool

ID="poolID") was not found in the Device Manager database.


ArrayGroup "chassis" or

"number".

In the specified request, the

"chassis" and "number" attributes of the ArrayGroup element cannot be specified.

In the specified request, the number of requested

ArrayGroup element must be one.

All "dpPoolID" attributes of

LogicalUnit element must have the same value.

The number of elements specified in the request is invalid. In the specified request, one child element

"child-element-name" must be specified for the "parent-

element-name" element.

A required element is missing from the request. "element-

name" or "element-name"

The array group


number") was not found in the storage subysystem.

The device number "device-

number" is specified more than once.

The drive types of all LDEVs that make up a single pool of

"PP Name (Dynamic

Provisioning)" must match.

A element "element-name" or attribute "attribute-name" is missing from the request.

The request contains both the capacityInKB parameter of the logical unit and the lba parameter of the LDEV.

An attempt to execute a request has failed. If option

"option-name" is specified, the

element-name element cannot be specified.

Revise the pool specification, and then retry the operation.

Specify both "chassis" and "number" for

ArrayGroup.


Revise the number of elements in the request, and then retry the operation.

Revise the specification of the elements in the request.

Revise the specification of the array group and storage subsystem.

Revise the device number specification.

Revise the specification of the LUs, and then retry the operation.


Specify either the capacityInKB parameter of the logical unit or the lba parameter of the

LDEV, but not both.




Error Code

KAIC07717-E

KAIC07720-E

KAIC07721-E

KAIC07722-E

KAIC07723-E

KAIC07724-E

KAIC07725-E

KAIC07726-E

KAIC07727-E

KAIC07728-E

KAIC07729-E


An attempt to execute a request has failed. If option

"option-name" is specified, the

attribute-name attribute in a

element-name element cannot be specified.

An attempt to create a

TrueCopy pair has failed. The

LDEV "LUSE" is a LUSE device.

The number of LDEVs in the

LUSE must be less than "max-

number-of-LDEVs-in-LUSE".


TrueCopy pair has failed. The


The RAID type and the number of data disks must be identical for all LDEVs in the

LUSE.


TrueCopy pair has failed. To create a TrueCopy pair using the V-VOL of a QuickShadow pair, the QuickShadow pair must be created beforehand.

An attempt to create a "pair-

name" pair has failed. The


The number of LDEVs in the

LUSE must be less than "max-

number-of-LDEVs-in-LUSE".


TrueCopy Async pair has failed because the size of the LDEV that makes up the LUSE was smaller than 1 GB.

In this API version, the

TrueCopyAsync pair operation for the specified storage subsystem is not supported.

The data pool for the specified storage subsystem is not in the same default controller as the LU that will make up the pair.


TrueCopy Async pair has failed because the default controller of the LU to be defined in S-

VOL was not the same as the current controller.

Error occurred while parsing response from host agent.

An error occurred while encoding the message.


Make sure that the request is valid, and then retry.

Check the size of the LDEV that makes up the

LUSE.

Check the API versions supported by this storage subsystem.

Create a data pool, and then try again.

Check the default controller and a current controller of the LU.




1-93

1-94

Error Code

KAIC07730-E

KAIC07731-E

KAIC07734-E

KAIC07735-E

KAIC07736-E

KAIC07737-E

KAIC07738-E

KAIC07739-E

KAIC07740-E

KAIC07741-E

KAIC07742-E


If you used Disk Array

Management Program or

Storage Navigator Modular to create an expanded LU from two or more volumes assign to an LUN, the expanded LU cannot be deleted.

Creation of an LDEV in the specified array group is not supported.

Invalid information was sent from host agent. Serial number of the subsystem that has the replication volume was not specified.

An attempt to get the information of the pair configuration on host "host-

name" has failed. Error detail :

"error-detail".

The configuration file specified by instance number "instance-

number" already exists on the host "host-name".


number" on Host "host-name" is not managed by Device

Manager.


number" on Host "host-name" does not exist on the host

"host-name".

The specified group "group-

name" exists in the configuration file (instance number "instance-number" on host "host-name").

This API version does not support the LUN Management option.

A value for the attribute

"priority" is not specified for all "ExternalPathInfo" elements.

The same value has been specified for the attribute

"priority" in multiple

"ExternalPathInfo" elements.

Use Disk Array Management Program or

Storage Navigator Modular to delete the LUN that cannot be used, and then use Device

Manager to refresh the subsystem.




Center.

Specify another instance number, and then retry.

Specify another group name, and then retry.

Check this subsystem's option list. You can also check the Device Manager Server XML

API manual and make sure that the running

API version supports the command.

Specify a value for the attribute "priority" either for all "ExternalPathInfo" elements or for no "ExternalPathInfo" elements.

Specify different values for the attribute

"priority" in multiple "ExternalPathInfo" elements.



Error Code

KAIC07743-E

KAIC07750-E

KAIC07751-E

KAIC07752-E

KAIC07753-E

KAIC07754-E

KAIC07755-E

KAIC07756-E

KAIC07757-E

KAIC07758-E


The value specified for the attribute "priority" in the element "ExternalPathInfo" differs from that specified for the specified path group.

The specified device name

"device-name" exists in the configuration file (instance number "instance-number" on host "host-name").

The specified group "group-

name" does not exist in the configuration file (instance number "instance-number" on host "host-name").

The host agent (URL = "url-of-

host-agent") does not support the "function-name" function.

An error occurred during a pair operation.

An attempt to delete the information for a pair configuration (instance number "instance-number" on host "host-name" and instance number "instance-number" on host "host-name") has failed.

Error detail, host "host-name"

: "error-detail"

An attempt to create a pair has failed. The specified pair configuration may remain in the configuration file (instance number "instance-number" on host "host-name" and instance number "instance-number" on host "host-name"). Error details: "error-detail"

An error occurred during processing of the service by the host agent. Host agent

Error Message : "host-agent-

message" Command Error

Message : "command-error-

message"

An error was detected in the host agent. Details: "error-

detail"

The specified configuration file with instance number is

"instance-number" does not exist on host "host-name".

For the attribute "priority", specify the same value as the attribute "priority" set for the specified path group.



Use a host agent of version "necessary-

version" or later.


Center.

Check that the configuration file exists on the host "host-name", and then retry.



1-95

1-96

Error Code

KAIC07759-E

KAIC07760-E

KAIC07761-E

KAIC07762-E

KAIC07763-E

KAIC07764-E

KAIC07765-E

KAIC07766-E

KAIC07767-E

KAIC07768-E

KAIC07769-E

KAIC07770-E


The specified configuration file

(instance number "instance-

number" on host "host-name") is not valid. The configuration file is changed, or, the specification of Command

Device is invalid.

The content of the specified configuration file (instance number "instance-number") is not the same as that on the host "host-name".

The specified device name does not exist in the configuration file (instance number "instance-number" on host "host-name").

An attempt to delete a pair has failed. Error detail, host

"host-name" : "error-detail".

Device Manager Server timed out.

An internal server error occurred, because the parameter "parameter" was not specified.

An attempt to create a pair has failed. The specified pair configurations may remain in the configuration files


number" on host "host-name" and instance number

"instance-number" on host

"host-name").

An attempt to start a HORCM instance (instance number

"instance-number") on host

"host-name" failed.

Some pairs may be not deleted.

An attempt to restart the

HORCM instance (instance number "instance-number" on host "host-name") has failed.

Error detail: "error-detail"

An internal server error occurred. An attempt to execute a service for the host agent has failed.

An attempt to shut down the

HORCM instance (instance number "instance-number" on host "host-name") has failed.

Error detail: "error-detail"

Check the configuration file (instance number

"instance-number" on host "host-name"), and correct it if necessary.

Perform a refresh.


Center.



Center.

Contact the administrator of the host, and then restart the HORCM instance on the host.


Center.



Error Code

KAIC07771-E

KAIC07772-E

KAIC07773-E

KAIC07774-E

KAIC07775-E

KAIC07776-E

KAIC07777-E

KAIC07778-E

KAIC07779-E


An attempt to get the result of

"operation" has failed.

An internal server error occurred. An attempt to create a request for the host agent was failed.

An attempt to create a pair has failed. Error details, host

"host-name1" : "error-detail", host "host-name2" : "error-

detail"

An attempt to create a pair has failed. Error detail, host

"host-name" : "error-detail"

An attempt to create a pair has failed. The specified pair configurations may remain in the configuration files


number" on host "host-

name1" and instance number

"instance-number" on host

"host-name2"). Error details, host "host-name1" : "error-

detail", host "host-name2" :

"error-detail"

An attempt to create a pair has failed. The specified pair configurations may remain in the configuration file (instance number "instance-number" on host "host-name"). Error details of Host "host-name" :

"error-detail"

An attempt to create a pair has failed. The specified pair configurations may remain in the configuration file (instance number "instance-number" on host "host-name1"). Error details, Host "host-name1" :

"error-detail", Host "host-

name2" : "error-detail"

An attempt to execute a request has failed. The host agent returned an invalid response.

An attempt to delete the configuration file (instance number "instance-number" on host"host-name") has failed.

Error detail : "error-detail"


Center.



1-97

1-98

Error Code

KAIC07780-E

KAIC07781-E

KAIC07782-E

KAIC07783-E

KAIC07784-E

KAIC07785-E

KAIC07786-E

KAIC07787-E

KAIC07788-E

KAIC07789-E

KAIC07790-E


An attempt to delete a pair has failed. Error details, host


detail"

An attempt to delete information for a pair configuration (instance number "instance-number" on host "host-name1" and instance number "instance-

number" on host "host-

name2") has failed. Error details, host "host-name1" :

"error-detail", host "host-

name2" : "error-detail"

An attempt to delete information for a pair configuration (instance number "instance-number" on host "host-name") was failed.

Error details : "error-detail".

An attempt to modify a pair has failed. Error details, host

"host-name" : "error-detail".

An attempt to modify a pair has failed. Error details, host


detail".

An attempt to restart a

HORCM instance (instance number "instance-number") on host "host-name" failed.

An internal error occurred in host agent ("agent-url").

The host agent (host-name

"host-name") cannot support the "function-name" function.

Use "PP on Host" of version

"necessary-version" or later on this host.

Device Manager Server cannot operate the host agent service

"operation".

An error occurred during processing of the service by the host agent. (error message from the host agent

= "error-message-from-host-

agent")

An attempt to get volume information on host "host-

name" has failed. Error detail :

"error-detail".

Check the configuration file, and then correct it if necessary.


Center.

Check the host agent environment.


Center.

Check the host agent status. If this problem persists, contact the Support Center.



Error Code

KAIC07791-E

KAIC07792-E

KAIC07793-E

KAIC07794-E

KAIC07795-E

KAIC07796-E

KAIC07797-E

KAIC07798-E

KAIC07799-E

KAIC07800-E

KAIC07801-E

Description

An attempt to get program product information on host

"host-name" has failed. Error detail: "error-detail".

An attempt to acquire pair volume information on the host "host-name" has failed.

Error details: "error-detail".

An attempt to execute the request has failed. The specified LU "device-number" is being used by PP Name

(UniversalReplicator).

Creation, modification, or deletion of UniversalReplicator or Continuous Access XP

Journal pairs is not supported.


(devNum = "Device number") used by PP Name

(UniversalReplicator) cannot be deleted.

An attempt to execute the request has failed. The specified LU "device-number" is being used as a journal volume.

LDEV of device number

"device-number" cannot be used to make up a LUSE because the device number is smaller than the maximum device number of the LDEVs that make up the first specified LUSE.

The microcode version of the storage array is insufficient for the requested an LUSE operation using a path defined

LDEV. The microcode version is "microcode-version"

An attempt to execute the request has failed. The specified LU "device-number" is being used as a system disk.

There are too many elements in the request. The maximum number of "element-name-in-

XML-API" elements which can be specified is "maximum-

number-of-elements".

A required element is missing from the request. Specify

"element-name" elements.


Center.


Revise the LU specifications, and then try again.




To create a LUSE based on a LUSE that has already been configured, specify an LDEV with a device number larger than the maximum device number of the LDEVs that make up the first LUSE.




Check that all of the required elements of a request are present. Provide the missing element, and then retry.



1-99

1-100

Error Code

KAIC07802-E

KAIC07803-E

KAIC07804-E

KAIC07805-E

KAIC07806-E

KAIC07807-E

KAIC07808-E

KAIC07809-E


The number of elements specified in the request is insufficient. To execute this command, "minimum-

number-of-elements" or more

"element-name" elements are required.

Missing parameter: "element-

name" "attribute-name-of-

element".

A parameter is invalid. The same object is specified for at least two "Path" elements in the request.

Some parameters are incorrect. The same WWN

"WWN

(xx.xx.xx.xx.xx.xx.xx.xx)" is specified for two or more

"WorldWideName" elements in the request.

The command cannot be executed because the security switch for the specified port

"port-name" is OFF. To execute this command, the security switch for the port must be ON.

An LUN group cannot be created because there are no paths on the specified port

"port-name". To create an

LUN group, there must be at least one path on the port at the creation destination.

The command cannot be executed because executing it will cause the number of LUN groups on the specified port

"port-name" to exceed the maximum number of LUN groups "maximum-number-of-

LUN-groups-that-can-be-

created-on-a-port" that can be created on a port.

The command cannot be executed because executing it will cause the number of WWN groups on the specified port

"port-name" to exceed the maximum number of WWN groups "maximum-number-of-

WWN-groups-that-can-be-

created-on-a-port" that can be created on a port.

Check the number of elements, then retry.

Specify the required parameter, and then retry.

Revise the specifications for the object of the path element, and then retry.

Check the WWN specifications of the

WorldWideName elements, and then retry.

Turn the security switch ON for the specified port, and then retry.

Create at least one path on the specified port, and then retry.

Revise the specifications for the ports and LUN groups so they do not exceed the maximum number, and then retry.

Revise the specifications for the ports and

WWN groups so they do not exceed the maximum number, and then retry.



Error Code

KAIC07810-E

KAIC07811-E

KAIC07812-E

KAIC07813-E

KAIC07814-E

KAIC07815-E

KAIC07816-E

KAIC07817-E

KAIC07818-E

KAIC07819-E

KAIC07820-E



"nickname" is invalid, since the maximum length for a nickname is "maximum-

length-of-nickname" bytes.


"nickname" is invalid, since it contains a forbidden character.


"nickname" is not available.

This nickname is already used by the other LUNGroup on the same port.



This nickname is already used by another WWN/WWNGroup on the same port.

The specified path cannot be used because it belongs to another LUN group on the same port.

The specified WWN "WWN" is not available. This WWN already belongs to the other

WWNGroup on the same port.

It is not possible to group paths that have different WWN securities each other. Paths that have same WWN securities or no WWN security must be specified.

It is not possible to group

WWNs used by different paths. WWNs that are used by the same path(s), or are not used, must be specified.

The specified path is not a path on the port "port-name".

A path that is on the specified port must be specified.

The specified WWN is a member of WWNGroup. In order to perform secure/unsecure by

WWNGroup, specify all WWNs that are members of the

WWNGroup.

The specified

HostStorageDomain includes a path belonging to an

LUNGroup. This command does not support secure/unsecure with paths belonging to an LUNGroup.

Check the nickname, and then retry.

Specify a nickname that is not used by other

LUNGroups on the same port, and then retry.


WWN/WWNGroups on the same port, and then retry.

Specify a path that does not belong to another

LUN group on the same port, and then retry.

Specify the WWN which does not belong to other WWNGroups on the same port, and then retry.

Check the specification of paths, and then retry.

Check the specification of WWNs, and then retry.

Revise the relationship between the specified port and path, and then retry.

Specify all members of the WWNGroup or specify WWN that does not belong to the

WWNGroup, and then retry.

Check that there is no path belonging to the

LUNGroup in the HostStorageDomain to specify, and then retry.



1-101

1-102

Error Code

KAIC07821-E

KAIC07822-E

KAIC07823-E

KAIC07824-E

KAIC07825-E

KAIC07826-E

KAIC07827-E

KAIC07828-E

KAIC07829-E

KAIC07830-E


This operation for the WWN comprising a WWNGroup is not supported by the specified

API version.

The specified WWN "WWN" is not available. This WWN already belongs to

HostStorageDomain

"HostStorageDomain" on the same port.

A non-representative LDEV

(devNum = "Device number") that is making up a LUSE was specified. A LUSE cannot be created by specifying a nonrepresentative LDEV.

A non-representative LDEV

(devNum = "Device number") that is making up a LUSE was specified. A path cannot be set to a non-representative LDEV.



This nickname is already used by another

WWN/HostStorageDomain on the same port.



This nickname is already used by another




This nickname is already used by another WWN on the same port.

The specified Host Storage

Domain

(nickname="Nickname for

Host Storage Domain", portID="Port ID") does not exist.

The specified WorldWideName

(nickname="Nickname for

WorldWideName") does not exist in the Host Storage

Domain (portID="Port ID", domainID="Domain ID").


(devNum = "Device number") set for PP Name

(QuickShadow) cannot be deleted.


Specify the WWN which does not belong to other HostStorageDomain on the same port, and then retry.



WWN/HostStorageDomain on the same port, and then retry.


HostStorageDomain on the same port, and then retry.


WWN on the same port, and then retry.

Revise the parameter specifications

Delete the settings, then delete the path.



Error Code

KAIC07831-E

KAIC07832-E

KAIC07833-E

KAIC07834-E

KAIC07835-E

KAIC07840-E

KAIC07841-E

KAIC07842-E

KAIC07843-E

KAIC07844-E

KAIC07845-E

KAIC07846-E


In this API version, creation, modification, and deletion of

"PP Name (QuickShadow)" pairs on the specified device is not supported.


(nickname = Nickname for

ISCSIName) does not exist in the host storage domain

(portID = Port ID, domainID =

Domain ID).

The specified host storage domain does not exist in the


There is no communication protocol by which host "host-

name" and host "host-name" can communicate with each other.

The IP address necessary to perform the specified operation is not registered with the host "host-name".

The specified port already has the maximum number of

LUNs.

The specified

HostStorageDomain already has the maximum number of

LUNs.

The specified LDEV (devNum

= "Device number") is not a

LUSE.

The specified LUSE (devNum

= "Device number") has an

LUN. LUSEs that have LUNs cannot be deleted with the

"DeleteLUSE" command.

Some parameters are incorrect. The same ruleID

"ruleID" is specified with two or more "Rule" elements in the request.

An attempt is being made to set multiple volumes for the same port, group, or LUN group (portID = "Port ID", domainID = "Domain ID", lun

= "LUN").

The LDEV (devnum = "Device

number") you are attempting to use, to make up the LUSE, is a command device.



Revise the host storage domain specification.

Revise the host settings.

Revise the host agent version, the RAID

Manager version, and/or the host settings.

No more LUNs can be specified on this port, select a different port on which to add LUNs.

No more LUNs can be specified on this

HostStorageDomain. Select a different

HostStorageDomain on which to add LUNs.

Make sure the specified LDEV is correct.

Make sure the LUSE specification is correct.

Check the specification of the ruleID of Rule elements, and then retry.

Check and, if necessary, revise the specifications.



1-103

1-104

Error Code

KAIC07847-E

KAIC07848-E

KAIC07849-E

KAIC07850-E

KAIC07851-E

KAIC07852-E

KAIC07853-E

KAIC07854-E

KAIC07855-E

KAIC07856-E

KAIC07857-E

Description

An attempt is being made to set multiple volumes for the same port, group, or LUN group (portID = "Port ID", lun

= "LUN").

The first specified LDEV

(devNum = "Device number") must have the lowest number from among the LDEVs in the list.

For the specified request, if

(type="array-group type") is specified in the ArrayGroup element, the dpPoolID or threshold attribute in a

LogicalUnit element cannot be specified.

In the specified request,

"type" attributes in more than one ArrayGroup element differ. All "type" attributes within the ArrayGroup elements must be the same.

The "force" option cannot be specified for this ArrayGroup element.

A specified ArrayGroup element (chassis="chassis", number="array-group

number") cannot be deleted because the LU "device

Number" in the array group is a pair device.

The specified LU "device

Number" cannot be deleted because it is a pair device.

This "API or CLI" version does not support deletion of "PP

name (QuickShadow)" virtual volumes.

This "API or CLI" version does not support creation of "PP

name (QuickShadow)" virtual volumes.

This request cannot specify an

ArrayGroup element that has the attribute

(chassis="chassis").

This request cannot specify a

LogicalUnit element that has the attribute

(chassis="chassis").


Revise the specification, and then retry.


Revise the specification of the ArrayGroup element "type" attributes, and then retry the operation.


Revise the specification of the ArrayGroup element, and then retry the operation.

Revise the specification of the LogicalUnit element, and then retry the operation.

Check what "API or CLI" versions support deletion of "PP name (QuickShadow)" virtual volumes.

Check what "API or CLI" versions support creation of "PP name (QuickShadow)" virtual volumes.

Revise the specification of the ArrayGroup element.

Revise the specification of the LogicalUnit element.



Error Code

KAIC07858-E

KAIC07860-E

KAIC07861-E

KAIC07862-E

KAIC07863-E

KAIC07864-E

KAIC07866-E

KAIC07867-E

KAIC07869-E

KAIC07870-E

KAIC07871-E

KAIC07872-E

Description

In the specified request,

"type" attributes in more than one LogicalUnit element differ.

All "type" attributes within the

LogicalUnit elements must be the same.

Missing parameter:

DataRetention "parameter-

name". At least one of these parameters is required to change the protection attributes.

The value for "parameter-

name" is invalid.

The specified LDEV is not an open volume. The protection attributes of the specified

LDEV cannot be changed.

The specified LDEV is not a representative-LDEV. The protection attributes of the specified LDEV cannot be changed.

The specified LDEV is an

OnDemand device. The protection attributes of the specified LDEV cannot be changed.

The specified LDEV is a PP

Name (VolumeMigration) reserved volume. The protection attributes of the specified LDEV cannot be changed.

The specified LDEV is a command device. The protection attributes of the specified LDEV cannot be changed.

The specified LDEV is not protected. The retention term cannot be set for an LDEV that is not protected.

The specified LDEV is a pool volume. The protection attributes of the specified

LDEV cannot be changed.

When the ioAccess value is changed to a value other than

Read/Write, replication cannot be set.

The ioAccess value is set to a value other than Read/Write, so replication cannot be set.

Revise the specification of the LogicalUnit elements.


Specify the required parameter, and then retry.

Specify a valid value, and then retry.



Revise the ioAccess and replication specifications.



1-105

1-106

Error Code

KAIC07880-E

KAIC07881-E

KAIC07882-E

KAIC07883-E

KAIC07884-E

KAIC07885-E

KAIC07886-E

KAIC07890-E

KAIC07891-E

KAIC07892-E

KAIC07893-E

KAIC07894-E

Description

The LUSE cannot be created because the CLPRs of the specified LDEVs (devnum =

"Device number" and devnum

= "Device number") are different.

An attempt to execute the request has failed. The specified LU cannot be used for a Delta Resync pair.

An attempt to execute the request has failed. The specified journal group cannot be used for a Delta Resync pair.

Execution of the request failed. At least one storage subsystem that makes up 3DC is not registered in the Device

Manager database.

An attempt to execute the request has failed. Some storage subsystems that make up the 3DC do not support

Delta Resync pair creation.

An attempt to execute the request has failed. The specified operation is not supported for the Delta

Resync pair.

An attempt to execute the request has failed. The specified pair cannot be deleted because a Delta

Resync pair exists.


number" is protected. It cannot be deleted.


number" is protected. It cannot be used for LUSE.

The specified LUSE volume

"device-number" is protected.

It cannot be released.


number" is protected. It cannot be used for a command device.


number" is protected. It cannot be used for S-VOL.




Add all the storage subsystems that make up

3DC, and then try again.

Check the microcode version of all storage subsystems that make up the 3DC.


Check the specification of the LU.


Check the specification of the LU.



Error Code

KAIC07895-E

KAIC07896-E

KAIC07897-E

KAIC07898-E

KAIC07899-E

KAIC07901-E

KAIC07902-E

KAIC07903-E

KAIC07904-E

KAIC07905-E

KAIC07906-E

KAIC07907-E

KAIC07908-E

KAIC07909-E

Description

The LU "device-number" that is P-VOL of the specified replication pair is protected.

Restore operation cannot be performed.

The LU "devNum" that is S-

VOL of the specified replication pair is protected.

Resync operation cannot be performed.

The specified array group contains protected LDEV(s).

The array group cannot be deleted.

The LU "device-number" that is S-VOL of the specified replication pair is protected.

The restore operation cannot be performed.


An agent service failed to execute because a proper method could not be found for the class-name class.

The request has failed. The attribute "attribute-name" was not specified.

The request has failed. The specified Host (name="host-

name", hostID="host-id") was unable to handle replication.

The request has failed. The specified Host ID "specified-

host-id" was not found in the database.

The request has failed. No

ReplicationInfo was specified.

The request has failed. An invalid value was specified for

"attribute-name".


"attribute-name".

The request has failed.

"attribute-name" was not specified.


"attribute-name".


"replicationFunction".


Check the specification of the replication pair.

Check the specification of the array group.

Check the specification of the replication pair.


The API requires "attribute-name" when the objectID is not specified. Add "attribute-name" to the request, and then retry.

Select a valid host, and then retry.


AddReplication requires at least one

ReplicationInfo. Add a ReplicationInfo to the request, and then retry.

Valid names must have length 1 to 31, and must not include whitespace(' '). Check the request, and then retry.

Valid values are 0 to 4094. Check the request, and then retry.

When creating new Configuration File, network port number is necessary. Check the request, and then retry.

Valid values are 0 to 65535. Check the request, and then retry.




1-107

1-108

Error Code

KAIC07910-E

KAIC07911-E

KAIC07912-E

KAIC07913-E

KAIC07914-E

KAIC07915-E

KAIC07916-E

KAIC07917-E

KAIC07918-E

KAIC07919-E

KAIC07920-E

KAIC07921-E

Description

The request has failed. An invalid value was specified for fenceLevel.







An attempt to execute the request has failed. The specified logical unit (serial number = "serial-number", device number = "device-

number") was not found in the database.

An attempt to execute the request has failed. The specified logical unit (serial number = "serial-number", device number = "device-

number") cannot be used for replication because it is

"cause".

An attempt to execute the request has failed. For the specified logical unit (serial number = "serial-number", device number = "device-

number"), security for the host has not been set.

An attempt to execute the request has failed. An invalid value has been specified for muNumber.

An attempt to execute the request has failed. The specified subsystem (serial number = "serial-number") was not found in the database.

An attempt to execute the request failed. No host agents were found for the specified host "host-name".

AddReplication requires the array type. Check the request, and then retry.

AddReplication requires a serial number.


AddReplication requires a device number.



Set the security for the host, and then perform a refresh.

Revise the muNumber specification.


Confirm that host agents have been installed for the host "host-name", and then restart the agents. If the host is a mainframe host, confirm that a valid URLLink has been specified.

Contact the Support Center. No more ReplicationGroups may be created.

No more ConfigFiles may be created.


Valid values are Never, Data or Status. Check the request, and then retry.



Error Code

KAIC07922-E

KAIC07923-E

KAIC07924-E

KAIC07925-E

KAIC07926-E

KAIC07927-E

KAIC07928-E

KAIC07929-E

KAIC07930-E

KAIC07931-E

KAIC07932-E

KAIC07933-E

KAIC07934-E

KAIC07935-E


The request has failed. Fence

Level 'Status' was not used for the specified subsystem.

The license key for "license-

name" has not been installed.

The license key for "license-

name" is disabled.


Duplicated pairNames "pair-

name" are specified.

The request has failed. The specified pairName "pair-

name" is already being used.

No more ReplicationInfo may be created.

The specified subsystem has just one port controller.

An attempt to execute the request has failed. A remote path or the MCU-RCU path between the local subsystem and the remote subsystem is not correctly set.

An attempt to execute the request has failed. The host

"host-name" does not recognize the specified logical unit (serial number = "serial-


"device-number").

The request has failed. The size of the specified

LogicalUnits pair does not match.

The request has failed. No pair could be created with the specified logical units by the specified replication function.

The request has failed. The emulation type of the specified

LogicalUnits pair does not match.

The request has failed. The default port controller of the specified LogicalUnits pair does not match.

An attempt to execute the request has failed. The specified array group (serial number = "serial-number", chassis = "chassis", number =

"array-group-number") was not found in the database.

Check the parameter, and then retry.

Contact the Support Center. Install the license key.

Contact the Support Center. Enable the license key.

Specify pair names which are unique in a

HORCM instance.


Dual-port-controller is necessary.

Revise the remote path or the MCU-RCU path.

Make sure that the host can recognize the logical unit, and then execute the host agent command "HiScan".

Specify the LogicalUnits whose size are same for P-VOL and S-VOL.


Specify the LogicalUnits whose emulation type are same for P-VOL and S-VOL.

Specify the LogicalUnits whose default port controller are same for P-VOL and S-VOL.




1-109

1-110

Error Code

KAIC07936-E

KAIC07937-E

KAIC07938-E

KAIC07939-E

KAIC07940-E

KAIC07941-E

KAIC07942-E

KAIC07943-E

KAIC07944-E

KAIC07945-E

KAIC07946-E

KAIC07947-E

KAIC07948-E

KAIC07949-E

KAIC07950-E

Description

The request has failed. The specified LogicalUnits pair does not match. RAID type does not meet the conditions.

The request has failed. The specified LogicalUnit was

LUSE.

The request has failed. The specified port number "port-

number" was already used in another configuration file.


Replication pairs in the same replication group must have the same replication function.


Replication pairs in the same replication group must have the same fence level.


Subsystems in the same replication group must be all

RAID or All DF.

The request has failed. The specified replication group cannot be operated on per group. The configuration file contains an unknown definition.

An unexpected response was returned from the host agent transport.

Some of the requests of "api-

name" has failed.

This GetHost request is invalid. "element-name" do not have a objectID.

The same object is included in a single request.

The specified storage subsystem does not support

TrueCopyAsync.

Reverse resynchronization cannot be performed for the specified pair.

An invalid replication configuration was specified.

The request has failed. The specified MU number is already in use.


Specify the LogicalUnits whose number of data disks are the same for P-VOL and S-VOL. If the pair is TrueCopy, RAID type of the

LogicalUnits must be "RAID5".

Specify the LogicalUnits which are not LUSE.

Specify the port number other than "port-

number".


Operate per pair.



Center.





Confirm that a replication configuration is valid.

Specify another MU number.



Error Code

KAIC07951-E

KAIC07952-E

KAIC07953-E

KAIC07954-E

KAIC07955-E

KAIC07956-E

KAIC07957-E

KAIC07958-E

KAIC07959-E

KAIC07960-E

KAIC07961-E


An attempt to execute the request has failed. The storage subsystem "storage-

array-name" can have a maximum of "max-number-of-

pairs" "replication-function" pairs.

An attempt to execute the request has failed. The specified subsystem

(sequence number =

"sequence-number") was not found in the database.

The request has failed. The specified logical unit pair is invalid. The number of configured LDEVs is different.

The request has failed. The specified host (name="host-

name", hostID="host-id") cannot handle replication.

"agent-or-raidmanager" is not installed.

The request has failed. The specified Host (name="host-

name", hostID="host-id") cannot handle replication. The host does not recognize the logical units.

The request has failed. The specified Host (name="name", hostID="host-id") cannot handle replication. The host does not recognize the command device.

The request has failed. The specified LogicalUnits are not open volumes.

An attempt to execute the request has failed. The combination of the pair that configures the group is invalid.

The request has failed. In the case of QuickShadow,

ReplicationInfo's status must be 'Simplex'.

The request has failed. In the case of QuickShadow, S-VOL must be QuickShadow V-VOL.

The request has failed. The specified P-VOL is not paired with selected V-VOL when

QuickShadow pair was made.

Delete an existing pair.


Specify the LogicalUnits whose number of

LDEVs are same for P-VOL and S-VOL.

Install "agent-or-raidmanager", and then retry.

Make sure that the host "host-name" recognizes the logical units, and then perform

"HiScan" command from the host agent.

Make sure that the host "name" recognizes the command device, and then perform

"HiScan" command from the host agent.

Specify open-volume-LogicalUnits for P-VOL and S-VOL.


Alternatively, specify a different group, and then retry.

Specify another LU, and then retry.

Specify QuickShadow V-Vol for S-VOL.

Specify another LU, and then retry.



1-111

1-112

Error Code

KAIC07962-E

KAIC07963-E

KAIC07964-E

KAIC07965-E

KAIC07966-E

KAIC07967-E

KAIC07968-E

KAIC07969-E

KAIC07970-E

KAIC07971-E

KAIC07972-E

Description

The request has failed. The

QuickShadow pair could not be created in the specified array system.

The request has failed. The port ID "port-id" is invalid.

An attempt to execute the request has failed. For the specified logical unit (serial number = "serial-number", device number = "device-

number"), security for the host has not been set on the specified port "port-ID".

An attempt to execute the request has failed. The host

"host-name" does not recognize the specified logical unit (serial number = "serial-


"device-number") on the specified port "port-ID".

An attempt to execute the request has failed. There are no paths on the specified port

"port-ID" for the specified logical unit (serial number =

"serial-number", device number = "device-number").

An attempt to execute the request has failed. There are no paths for the specified logical unit (serial number =

"serial-number", device number = "device-number").

The request has failed. No port was found.

In this API version,

QuickShadow is not supported.

The specified icon "icon" is invalid.

An attempt to execute the request has failed. Multiple pairs for one P-VOL of

QuickShadow cannot be restored at the same time.

The request has failed. The specified instance number

"instance-number" is already in use.



Specify another port ID, and then retry.

Set the security for the host, and then perform a refresh.

Make sure that the host can recognize the logical unit, and then execute the host agent command "HiScan".

Set a path for the logical unit on the specified port.

Set a path for the logical unit.

Confirm the port status.


Check the specified icon file.


Specify another instance number.



Error Code

KAIC07973-E

KAIC07974-E

KAIC07975-E

KAIC07976-E

KAIC07977-E

KAIC07978-E

KAIC07979-E

KAIC07980-E

KAIC07981-E

KAIC07982-E

KAIC07983-E

KAIC07984-E

Description

The LUSE could not be created because the types or attributes of the specified

LDEVs (devnum = "Device

number" and devnum =

"Device number") are not identical.

The paths cannot be create to the external port "port name".

Creating or deleting external volumes is not supported.

The specified DevNum "Device

number" already exists in the


An attempt to execute the request has failed. There are no Differential Management

LUs in the specified device.

The specified parameter is invalid. The value that can be specified for a pattern attribute of the WritingPattern element is a hexadecimal number from "Min. parameter

value" to "Max. parameter

value" bytes.

The specified last

WritingPatterns element parameter is invalid.

The specified parameter is invalid. "element-name"

"attribute-name-of-element" :

"attribute-value-of-element"

The stripe sizes of the LDEVs do not match. The LUSE

(devNum = "Device number") cannot be created.

The specified stripeSizeInKB is invalid.

An attempt to execute the request has failed. The specified replication function is not supported in this subsystem.

An attempt to execute the request has failed. The specified replication operation is not supported for this subsystem.




Make sure that all of the LDEVs making up the

LUSE satisfy the following conditions:



The volume classes (internal or external) are identical.





The disk types are identical.

The host's I/O suppression modes are identical.

The cache modes are identical.

Check and, if necessary, revise the port specification.

Check and, if necessary, revise the specification of the LDEV or ArrayGroup.

Revise the specification for devNum of the

LogicalUnit elements, and then retry.

Create a Differential Management LU, and then retry.



Make sure that the specified parameter is valid, and then retry.

Make sure the LDEV specifications are correct.






1-113

Error Code

KAIC07985-E

KAIC07986-E

Description

An attempt to execute the request has failed. The specified replication operation cannot be performed for this emulation type of this volume.

An attempt to execute the request has failed. There is no specified journal group.





Error Code

KAIC07987-E

KAIC07988-E

KAIC07989-E

KAIC07990-E

KAIC07991-E

KAIC07992-E

KAIC07993-E

KAIC07994-E

KAIC07995-E

Description

An attempt to execute the request has failed. The journal group cannot be used because the journal volume is not registered.

An attempt to execute the request has failed. The specified journal group is already being used by the mainframe function.

An attempt to execute the request has failed. The specified journal group is already used as a primary journal group or secondary journal group.

An attempt to execute the request has failed. The specified MU number cannot be used.

An attempt to execute the request has failed. The combination of the journal groups is invalid.

An attempt to execute the request has failed. The CLPR of the pair volume does not match the CLPR of the journal volume that configures the journal group.

An attempt to execute the request has failed. The combination of the journal group and the replication group is invalid.

An attempt to execute the request has failed. All replication pairs in the same replication group must use the same journal group.

The requested operation could not be performed. The specified LU is being used for a PP Name (Dynamic

Provisioning) pool, and cannot be used as the P-VOL or S-

VOL.


Revise the specification, and then retry.





1-115

1-116

Error Code

KAIC07996-E

KAIC07997-E

KAIC07998-E

KAIC08000-E

KAIC08001-E

KAIC08002-E

KAIC08003-E

KAIC08004-E

KAIC08005-E


The requested operation could not be performed. A PP Name

(Dynamic Provisioning) volume cannot be used as the

P-VOL or S-VOL for the following replication function.

Replication function: PP Name

(TrueCopy, TrueCopyAsync,

QuickShadow,

UniversalReplicator)

The requested operation could not be performed. If you use a

PP Name (Dynamic

Provisioning) volume as the S-

VOL for PP Name

(ShadowImage), you must also use a PP Name (Dynamic

Provisioning) volume as the P-

VOL.

An attempt to execute the request has failed. The CLPR of the pair volume does not match the CLPR of the pair volume that belongs to the journal group.

A part that differs from the actual machine was found in the subsystem information.

Refresh the subsystem. If you are a local user, contact the system administrator.

A part that differs from the actual machine was found in the subsystem information.

Refresh the subsystem. If you are a local user, contact the system administrator. (error =

"error")

"FreeSpace" cannot be specified. Revise the "

" bulk

"," dividebycap

", and

" dividebynum then retry.

" options, and

This API version does not support batch operations on

Lus.

An attempt to execute a request has failed. The combination of options "option

name" and "option name" is invalid.

The number of LUs that can be deleted cannot exceed

"maximum number of LUs".


The Device Manager server might not contain the latest storage subsystem information.

Refresh the information by using the GUI refresh function, or by executing

AddStorageArray of the API.

Revise the option specification.

Make sure that the API version supports the command.

Revise the option specification.




Error Code

KAIC08006-E

KAIC08007-E

KAIC08008-E

KAIC08009-E

KAIC08010-E

KAIC08011-E

KAIC08012-E

KAIC08013-E

KAIC08014-E

KAIC08015-E

KAIC08016-E

KAIC08017-E

KAIC08018-E


Batch deletion is not possible for LUs whose emulation is not

OPEN-V. (devNum = device

number)

An LDEV (devNum = device

number) that has a path defined cannot be deleted.

An LDEV (devNum = device

number) that has a LUSE defined cannot be deleted.

The specified array group does not exist in the Device

Manager database.

The specified array group does not have sufficient free space.

The Device Manager database does not have sufficient free space.

A "PP Name (Dynamic

Provisioning)" volume

(devNum = "device number") cannot be deleted in Device

Manager.

An attempt to execute a request has failed. When

"option name" is specified,

"option name" must also be specified.

This subsystem does not support batch operations on

LUs.

Batch creation is not possible for LUs whose emulation is not

OPEN-V.

The request syntax is incorrect. The attribute

"attribute-name" is not specified in the element

"element-name".

The request syntax is incorrect. The value

"attribute-value" (specified for the attribute "attribute-name" in the element "element-

name") is duplicated.

The request syntax is incorrect. The attribute

"attribute-name" is not specified in the element

"param" (name = "element-

name").


Defined paths must be deleted before deleting

LDEVs.

LUSEs must be deleted before deleting LDEVs.



Revise the free space specification.



Check the subsystem.

Revise the emulation type specification.

Revise the request syntax, and then try again.





1-117

1-118

Error Code

KAIC08019-E

KAIC08020-E

KAIC08021-E

KAIC08022-E

KAIC08023-E

KAIC08024-E

KAIC08025-E

KAIC08026-E

KAIC08027-E


Execution of the request failed. The value "attribute-

value" (specified for "Type" in the parameter "parameter-

name") is invalid.


value" (specified for "value" in the parameter "parameter-

name") is invalid. Specify the value as "valid-values (only

"2")".


value" (for "value" in the parameter "parameter-name") is invalid. Specify a value that is no more than "max-

character-string-length" characters.


value" (for attribute

"attribute-name" in element

"element-name") is invalid.

Execution of the request failed. If the parameter

"parameter-name" is specified, the parameter

"parameter-name" must also be specified.


value" (for "value" in the parameter "parameter-name") is invalid. Specify a size that is within the free-disk space of

"InPool".

The request syntax is incorrect. The invalid attribute

"attribute-name" is specified in the element "parameter-

name".

The request syntax is incorrect. The child element

"ArrayValue" must be specified for the parameter

"parameter-name".


value" (for the attribute

"value" of the child element

"ArrayValue" in the parameter

"parameter-name") is invalid.












Error Code

KAIC08028-E

KAIC08030-E

KAIC08100-E

KAIC08101-E

KAIC08102-E

KAIC08103-E

KAIC08104-E

KAIC08105-E

KAIC08106-E

KAIC08107-E

KAIC08108-E

KAIC08110-E

KAIC08111-E


An attempt to execute a request has failed. The number of child elements for parameters "parameter-name" and "parameter-name" are not the same.

The specification method

("method-name") cannot be executed. Wait a while, and then try again. (object path =

"object-path")

You have already selected another subsystem

("subsystem-name"). You can reserve only one subsystem at a time.

The subsystem has been reserved by user "user-name".

A reserved subsystem cannot be deleted.

The properties, except for the name of the reserved subsystem, cannot be changed.

Another application has already reserved the specified subsystem. Only the reserving application can perform operations now.

The subsystem is not reserved, or the reservation was released because the time limit was exceeded.

The specified command is not available for reserved subsystems.

The reservation status has been changed.

The specified command cannot be executed using the storage subsystem microcode version

"microcode-version".

This command cannot be executed because, for the specified storage subsystem, only one "PP Name (Dynamic

Provisioning)" volume can be added to an array group.

This command cannot be executed because, for the specified storage subsystem, the array group must be specified.



Center.

Release the reservation on the other subsystem, then retry the operation.

After the subsystem reservation has been released, retry the operation.

Retry the operation from the reserving application.

Check whether the reservation has been released.

After the subsystem reservation has been released, retry the operation.

Check the reservation status.

Make sure the microcode version of the storage subsystem is correct.





1-119

1-120

Error Code

KAIC08112-E

KAIC08113-E

KAIC08114-E

Description

The specified external array group "external array group

name" cannot be deleted because Device Manager does not contain any externally mapped volume information for the external array group.

The specified external array group "external array group

name" cannot be deleted because the emulation type is not OPEN-V.

External array groups can only be deleted from the CLI.


Revise the external array group information.

Revise the external array group information.

Use the CLI to execute the request.

Table 1-10 KAIC09000-KAIC09999: CIM/WBEM Errors

Error Code

KAIC09000-E

KAIC09001-E

KAIC09002-E

KAIC09003-E

KAIC09004-E

KAIC09005-E

KAIC09006-E

KAIC09007-E

KAIC09008-E

KAIC09009-E

Description

An unidentifiable CIM Wbem service error was encountered.

"CIM-class-name" class does not support the "method-

name" method.


An attempt to find the "CIM-

class-name" class has failed.


"stack-trace"


The ACL users table is empty.


The ACL rules table is empty.

Authentication has failed. username: "user-name"

The operation was denied. username: "user-name", write request: "whether-request-

needs-write-permission"

The operation was not authorized. username: "user-

name", write request:

"whether-request-needs-write-

permission"

The "requested-operation-

name" operation has failed.



Use another operation. If the used operation should be supported, contact the Support

Center.


Check the server condition ACL users.

Check the server condition ACL rules.

Check the username and password, and then retry.

Check the username, password and user permissions, and then retry.

Follow the last related message. If there is no related message, contact the Support Center.



Error Code

KAIC09011-E

KAIC09012-E

KAIC09013-E

KAIC09014-E

KAIC09015-E

KAIC09016-E

KAIC09017-E

KAIC09018-E

KAIC09019-E

KAIC09020-E

KAIC09021-E

KAIC09022-E

KAIC09023-E

KAIC09024-E

KAIC09025-E


An attempt to create a CIM-

Instance failed. Class:"CIM-

class-name", Key:"key-

properties", "stack-trace"


An attempt to create a CIM-

ObjectPath has failed.

Class:"CIM-class-name",

Key:"key-properties", "stack-

trace"

The WQL is invalid.

Property:"property-name",

Operator:"operator(number)",

Value:"value"

The WQL is unsupported.

Property:"property-name",

Operator:"operator(number)",

Value:"value"

This association cannot be associated.

Source(Class:"source-CIM-

class-name",Role:"source-

role") and Result(Class:"result-

CIM-class-name",Role:"result-

role")

Check the specified WQL or ObjectPath, and then retry.


This association is not supported as a result class of this Association class. "class-

name"

An invalid key property exists in the ObjectPath. "key-name"


Check the specified ObjectPath, and then retry.

An attempt to obtain a class name from ObjectPath has failed. ObjectPath:

"ObjectPath"

The WQL is invalid. wql:"WQL" Check the specified WQL or ObjectPath, and then retry.

The class is invalid. class:

"class-name"

Check the specified ObjectPath, and then retry.

The property is invalid.

Property: "property-name" value: "value"

Check the specified WQL or ObjectPath, and then retry.

The role parameter is invalid.

"role"

The parameter is invalid. When

ResultClass is not specified,

PropertyList cannot be specified.

The argument type is invalid.

"type"


"object-name" is null.

Check the specified role or resultRole, and then retry.

Specify the ResultClass, or do not specify the

PropertyList.

Check the specified argument type, and then retry.




1-121

1-122

Error Code

KAIC09026-E

KAIC09027-E

KAIC09028-E

KAIC09029-E

KAIC09100-E

KAIC09101-E

KAIC09114-E

KAIC09501-E

Description

The instance does not exist.

Object path:"Object path"

In the "requested-operation-

name" operation, An attempt to retrieve data for the storage array has failed.

An attempt to execute a request failed. Check and, if necessary, revise the request, and then try again.

An attempt to execute a request failed. Check and, if necessary, revise the operating environment, and then try again.

CIM-WBEM Service initialization error: an invalid

HTTP port number "port-

number" has been specified.

CIM-WBEM Service initialization error: an invalid

HTTPS port number "port-

number" has been specified.

An attempt to start the CIM-

WBEM Service on port "port-

number" failed.

An error occurred within SLP

API processing. SLP error number: "SLP-error-number", error details: "error-detail"


Check the object path, and then re-execute.

Follow the last related message. If there is no related message, contact the Support Center.

Check and, if necessary, revise the request, and then try again.

Check the operating environment. If the error persists, contact the Support Center.

Confirm the value of "server.properties" and restart the services.

Stop any service that uses a port having a port number used by the CIM-WBEM Service, and restart the Device Manager Server.

Check if the SLP daemon is running. If it is not running, then start it and restart the

Device Manager Server. If this error occurs even the SLP daemon is already running, then contact the Support Center.

Table 1-11 KAIC30000-KAIC39999: Trace messages

Error Code

KAIC30004-I

KAIC30005-I

KAIC30017-I

KAIC32006-I

KAIC32007-I

KAIC32101-I

KAIC32102-I

KAIC33020-W

KAIC33025-W

KAIC33026-I

KAIC35435-I

Description

Device Manager Server has started.

Device Manager Server has stopped.

Device Manager Server has started in Secure mode.

Device Manager HiKeyTool has started.

Device Manager HiKeyTool has stopped.

Device Manager "client-name" has started.

Device Manager "client-name" has finished.

An inconsistency was detected from the database information. The database will now be initialized.

An inconsistency was detected from the database information. Restore the database from the backup.

The database will now be initialized.

The version of the "library-name" is "version (additional-information)".



Error Code

KAIC35436-W

KAIC39004-I

KAIC39005-I

Description

An attempt to get the version of "library-name" has failed (Error code "error-

code").

The CIM-WBEM Service has started.

The CIM-WBEM Service has stopped.



1-123

Device Manager Web Client Messages

The Device Manager Web Client error messages are output to the following log files:



For Windows systems:

Device-Manager-installation-

destination\DeviceManager\HiCommandServer\logs\HDvMGuiTracen.log



For Solaris and Linux systems:

/opt/HiCommand/HiCommandServer/logs/HDvMGuiTrace

n.log where n is a numerical value that indicates the file number.

The Web Client error messages are output to the log files in the following

format (see Table 1-12):

serial-number date time program-name process-ID thread-ID ID type message

Table 1-13 lists the Hitachi Device Manager Web Client GUI error messages,

and provides recommended actions for resolving the error conditions. The error messages are listed in numerical order by error code. For errors whose recommended action is "Contact the Support Center.", first collect maintenance information by executing the hcmdsgetlogs command, and then

contact the Hitachi Data Systems Support Center (see Calling the Hitachi Data

Systems Support Center for contact information).

Table 1-12 Format of Messages Output to Log Files

Item

Serial number

Date

Time

Program name

Process ID

Thread ID

ID

Description

Serial number of the message.

Date the error occurred, in yyyy/mm/dd format.

Time the error occurred, in hh:mm:ss:xxx format (xxx indicates milliseconds).

Component name or command name of Device Manager.

Process ID of the program that requested the log output.

Thread ID of the program that requested the log output.

Message ID. Device Manager messages are output in KAICmmmmm-X format.

KAIC: Character strings that indicate the message is output from

Device Manager.

mmmmm: Error code.

X: Indicates the error level. One of the following is displayed:

I

(nonerror information),

W

(warning), or

E

(error).

1-124

Message Message.



Table 1-13 KAIC10000-KAIC11999: Hitachi Device Manager Web Client

GUI Errors

Error Code

KAIC10001-W

KAIC10002-W

KAIC10003-W

KAIC10004-W

KAIC10005-W

KAIC10006-W

KAIC10010-W

KAIC10011-W

KAIC10012-W

KAIC10013-W

KAIC10015-W

KAIC10016-W

KAIC10017-W

Description

Currently, there are commands being processed for subsystem <subsystem-

name>.

Cannot Move Storage to a

LogicalGroup which has different subsystem.


name>.

There are processing tasks still running on logical group "<logical-

group-name>".

There are processing tasks still running on storage subsystem

"<subsystem-name>".


name>.

Subsystem is busy. Please retry this action after the previous action is completed.


Please retry this action after the active commands are completed.

Please move storage to a Logical

Group which contains storage in same storage subsystem.

Please retry this action after the active commands are completed.

An attempt to add the storage has failed.

Please retry this action after the previous action is completed.







An attempt to move same LUN has failed.


An attempt to delete the LUN security has failed.


An attempt to remove the Port has failed.


An attempt to delete the group has failed.




1-125

1-126

Error Code

KAIC10018-W

KAIC10019-W

KAIC10024-W

KAIC10025-W

KAIC10026-W

KAIC10027-W

KAIC10028-W

KAIC10029-W

KAIC10030-W

KAIC10031-W

KAIC10032-W

KAIC10033-E

KAIC10034-W

Description












The server is returning a Message ID that is used by a previous command.

Delete alerts is in process. Please retry this action after the previous action is completed.


An attempt to delete the storage has failed.


An attempt to delete the storage array has failed.


An attempt to scan LUN has failed.


An attempt to delete the storage from multi groups has failed.


An attempt to add the Logical Unit has failed.


An attempt to delete the Logical Unit has failed.


An attempt to add the array group has failed.


An attempt to define spares has failed.


An attempt to delete the array group has failed.


An attempt to modify the port controller has failed.


An attempt to add HostStorageDomain has failed.


If this error persists, please contact the Support Center.

Please retry this action after the active action is completed.



KAIC10039-E

KAIC10040-E

KAIC10041-E

KAIC10042-E

KAIC10043-E

KAIC10044-E

KAIC10045-E

KAIC10046-E

KAIC10047-E

KAIC10048-E

KAIC10049-E

Error Code

KAIC10035-E

KAIC10036-E

KAIC10037-E

KAIC10038-E

Description

Device Manager Web Client was unable to communicate with the



Check the network status and whether the Device Manager server is running correctly.

If a network problem exists, remove its cause.

If the Device Manager server has stopped, start it. If you cannot start the server, contact the Support

Center.

Even if the Device Manager server is running correctly, this message might be output if the Device Manager server takes an unusually long time to start because of its status when it last stopped. In this case, wait a while and then retry starting the server.

Please contact the Support Center.

Device Manager Web Client internal error has occurred.

A problem was encountered trying to download and install the server certificate. Device Manager Web Client is unable to access the Device

Manager Server through the secure channel. Please contact your system administrator for assistance.

A file required for a secure socket connection cannot be downloaded.

Click OK to exit the system.












Please ask the system administrator if the Keystore file is located in correct location on the server machine.

Please check the network configuration.




1-127

1-128

KAIC10058-E

KAIC10059-E

KAIC10060-E

KAIC10061-E

KAIC10062-E

KAIC10063-E

KAIC10064-E

KAIC10065-E

KAIC10066-E

KAIC10067-E

Error Code

KAIC10050-E

KAIC10051-E

KAIC10052-E

KAIC10053-E

KAIC10054-E

KAIC10055-E

KAIC10056-E

KAIC10057-E

KAIC10068-E

KAIC10069-E

KAIC10070-E

KAIC10071-E

KAIC10072-E

Description




























Error Code

KAIC10073-E

KAIC10074-E

KAIC10075-E

KAIC10078-E

KAIC10079-W

KAIC10081-W

KAIC10082-W

KAIC10083-W

KAIC10084-W

KAIC10085-W

KAIC10086-E

KAIC10087-W

KAIC10088-W

KAIC10089-E

KAIC10091-W

KAIC10092-W

KAIC10093-W


A user is not permitted to log in as

Peer.

Since the version of JRE is old,WebClient cannot be started. The version of JRE which is operating now is <JRE-version>.

The Logical Group that you have selected no longer exists.

Cannot parse "<value>" into a floating point number.

No LU is selected.

Please log in not as Peer.

Confirm that you are using a JRE version that is supported for use with

Web Client.

Please open another window, then come back to the original window. If this error persists, please contact the

Support Center.

If this error persists, please contact the Support Center.

Please continue process after selecting the storage.

Please check the network configuration. If you want to launch

Storage Navigator or Dynamic Link

Manager, please check if the selected application is working properly.

Please continue operation after a logical group is selected.

Device Manager cannot modify the logical group because no logical group has been selected.

A logical group cannot be deleted if it or a child group has already been allocated to a resource group. The resource group must be deleted first.

Please retry operation after deleting the resource group.

Device Manager cannot delete the logical group because no logical group has been selected.

Storage cannot be moved to a logical group assigned to the resource group

<resource-group-name>.


Please move the storage to a logical group that is not assigned to the resource group.

Device Manager cannot proceed to the next step because no logical group is selected.


There was an error adding a new host. Contact the Support Center.

Currently, there are commands being processed for subsystem <name>.

Please continue operation after the active process is finished.

Currently, there are commands being processed for subsystem <name>.



All of the disks in an array group must be in the same row and chassis.

You must select at least two (2) disks to create an array group.

All of the disks in an array group must be next to one another.

Please select disks which are located in the same row and chassis.

Please select at least two disks.

Please select disks located next to each other (contiguous).



1-129

1-130

Error Code

KAIC10094-W

KAIC10095-W

KAIC10096-E

KAIC10097-E

KAIC10098-E

KAIC10099-W

KAIC10100-W

KAIC10101-W

KAIC10103-W

KAIC10104-E

KAIC10105-E

KAIC10106-E

KAIC10108-E

Description

You cannot delete the user who is currently logged on.


To delete the specified user, first log on as another system administrator or local system administrator.

Please delete the specified user after creating one or more users.

You have asked to permanently delete the last <resource-group-name> user. There must always be at least one user of this type for Device

Manager to work.



Inconsistent properties found in the logical group "<name>".

No storage is selected.


The Storage Array is not selected!

This resource group name already exists. Select a different name.

Your user ID or password is invalid, please check with the Administrator.

Device Manager Web Client has lost the network connection to the Device

Manager Server. This might be due to a network problem or the server may be down. Device Manager Web Client will now exit. Please check your network connection and try again later.

Please retry operation after the storage is selected.

Please retry operation after the storage subsystem is selected.

Please select a resource group name which is not duplicated.

Please select a user name which is not duplicated.

Please confirm your user ID and password with the Administrator.

Please check if Device Manager is running properly. Please also check network condition.

Also confirm that the number of LDEVs specified for a single operation does not exceed the maximum specifiable number. This maximum number is approximately 200 if each LDEV has one volume path, or 100 if each LDEV has two volume paths.

Please check if Device Manager Agent is running properly. Please also check network condition.

Device Manager has lost the network connection to the Device Manager

Agent. This might be due to a network problem or the agent may be down.

The Device Manager Server Certificate has expired. Device Manager Web

Client will now exit. Please contact your system administrator for assistance.

The requested service is not currently implemented on the Device Manager

Server.

Please contact the system administrator.

Please go to the Help, Index in menu bar to check if the versions of server and Web client match.



KAIC10113-E

KAIC10114-E

KAIC10123-E

KAIC10124-E

KAIC10125-E

KAIC10126-E

KAIC10127-E

KAIC10128-E

KAIC10129-E

KAIC10130-E

Error Code

KAIC10109-E

KAIC10110-E

KAIC10111-E

KAIC10112-E

KAIC10131-E

KAIC10132-E

KAIC10133-E

Description

An unexpected error occurred in the

Device Manager Web Client.

An unexpected error occurred in the


Device Manager Server received bad request.

Device Manager Server received too large request.



Device Manager Server is shutting down now.

Device Manager Server cannot find files to be downloaded.

Missing host in message response.

Missing HostInfo in message response.

Parent Group "<logical-group-name>" was deleted in a previous command.

The new parent group already contains storage.

Group Name is duplicated!

The Group Name "<logical-group-

name>" is reserved!

The parent group is busy.

Please contact the System administrator to resize the maximum size of acceptable request for Device

Manager Server.



Please select another logical group for the parent group.

Please select another group name.

Login process to Device Manager

Server is failed. Web Client is shutting down now since there is a possibility of having network problem. Please login after checking network connectivity.

Failed to receive messages from

Device Manager Server. Web Client is shutting down now since there is a possibility of having network problem.

Please check your network connection and try again later.

Failed to receive messages from



Failed to receive command result from



Please retry this action after the active action is completed.

Please check if Device Manager is running properly. Please also check network condition.



1-131

1-132

Error Code

KAIC10134-W

KAIC10135-W

KAIC10136-W

KAIC10137-W

KAIC10139-E

KAIC10140-E

KAIC10141-W

KAIC10142-W

KAIC10143-W

KAIC10144-W

KAIC10145-W

KAIC10146-W

KAIC10147-W

KAIC10148-E

KAIC10149-W

KAIC10150-W

Description

The password you entered was not correct. You will not be permitted to continue this operation.

More than <number> of disks cannot be defined as spare disks of this subsystem.

The subsystem is busy.


Please check the password.

Please select fewer spare disks than specified.

The subsystem is busy.

Device Manager Server internal error has occurred.

<program-name> cannot be started up.



One or no WWNs exist in the WWN group <WWN-group-name>. Make sure that two or more WWNs exist in the WWN group.

No LUNs exist in the LUN Group

<LUN-group-name>. Make sure that more than one LUN exists in the LUN

Group.

A WWN group of the same name already exists in either the dropdown list or storage subsystem.

An LUN group of the same name already exists in either the dropdown list or storage subsystem.

The subsystem is busy. Try this action again once the previous action has completed.

The specified WWN is being used with a different LUN/LUN Group, and cannot be registered.

WWN group names must be less than eight characters, and more than one character.

LUN group names must be less than eight characters, and more than one character.

Wait until the processing finishes, and then retry the operation.




Add two or more WWNs to the WWN group.

Add one or more LUNs to the LUN group.

Change the name of the WWN group to one which does not exist.

Change the name of the LUN group to one which does not exist.


Change the security of the LUN of the corresponding WWN, or de-allocate the WWN.

Change the name.



Error Code

KAIC10151-W

KAIC10152-W

KAIC10153-E

KAIC10154-E

KAIC10155-E

KAIC10156-E

KAIC10157-E

KAIC10158-W

KAIC10159-W

KAIC10160-W

KAIC10161-W

KAIC10162-W

KAIC10163-W

Description

Only the following characters can be used in group names:

ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz

0123456789

_-+=.@!#$%&'^~`[](){}

Only the following characters can be used in group names:

ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz

0123456789

_-+=.@!#$%&'^~`[](){}


The LDEV "<DevNum>" can not be used as a command device.

The capacity of the LDEV is not sufficient.




A duplicate nickname is specified.

The specified nickname "<nickname>" is not available. This nickname is already used by another


The specified nickname "<nickname>" is not available. This nickname is already used by another

WWN/HostStorageDomain on the same port.

The WWN Group could not be registered, because LUN security is disabled. Please enable LUN security.

The LUN Group could not be registered, because LUN security is disabled. Please enable LUN security.

The cascading copy pairs by

ShadowImage / BusinessCopy exist in the group <group-name> (Host:

<host-name> HORCM: <instance-

number>). Cascading copy pairs cannot be specified in the same group. Please select different groups.


Change the name.


Check the capacity of the LDEV/LU and choose another.


Specify a unique nickname, then retry.

Change the name of the

HostStorageDomain to one which does not exist.

Change the name of the

WWN/HostStorageDomain to one which does not exist.

Enable LUN security for this port.

Select another group, or create a new group.



1-133

1-134

KAIC10170-E

KAIC10171-E

KAIC10172-E

KAIC10173-E

KAIC10174-E

KAIC10175-E

KAIC10176-E

KAIC10177-E

KAIC10178-E

KAIC10179-E

KAIC10180-E

KAIC10181-E

KAIC10182-E

Error Code

KAIC10164-W

KAIC10165-W

KAIC10166-W

KAIC10167-W

KAIC10168-W

Description

The specified copy pair name <copy-

pair-name> already exists in Host:


number>. Please enter a different copy pair name.

The specified copy pair name <copy-

pair-name> is duplicated in Host:


number>. Please enter a different copy pair name.

The group <group-name> (Host:


number>) cannot register this combination of copy pairs, since the subsystem type that the copy pairs are using is different.



number>) cannot register this combination of copy pairs, since the fence level that the copy pairs are using is different.



number>) cannot register this combination of copy pairs, since the different combination of P-VOL and S-

VOL subsystem are existed in this group.

Select the storage to be deleted.

Select the storage to be moved.

Select the storage for which you want to modify security.

Select multiple storage for which you want to create a LUSE.

Select the storage for which you want to delete a LUSE.

Select the storage to be allocated.

Select the storage to be unallocated.

Select the storage for which you want to create a copy pair.

Select storage belonging to a single subsystem.

The group name is not specified.

The group name "<group-name>" is a reserved name.

The host name is not specified

The specified World Wide Name is invalid.


Specify another copy pair name.

Select another group, or create a new group.

Only one combination of P-VOL and S-

VOL storage subsystem copy pair can be specified in one group. Select another group, or create a new group.

Select the storage to be deleted.

Select the storage to be moved.

Select the storage for which you want to modify the security.

Select multiple storage to create a

LUSE.

Select the storage for which the LUSE will be deleted.

Select the storage to be allocated.

Select the storage to be unallocated.

Select the storage for which a copy pair will be created.

Select storage belonging to a single storage subsystem.

Enter a group name.

Enter another group name.

Enter a host name.

Enter a valid World Wide Name.



Error Code

KAIC10183-E

KAIC10184-E

KAIC10185-E

KAIC10186-E

KAIC10187-E

KAIC10188-E

KAIC10189-E

KAIC10190-E

KAIC10191-E

KAIC10192-E

KAIC10193-E

KAIC10194-E

KAIC10195-E

KAIC10196-E

KAIC10197-E

KAIC10198-E

KAIC10199-E

KAIC10201-E

KAIC10204-E

KAIC10205-E

KAIC10206-E

KAIC10207-E

KAIC10208-E

KAIC10209-E


The World Wide Name must be unique.

The IP address or host name is not specified.

The user ID is not specified.

Enter another World Wide Name.

Enter an IP address or host name.

Enter a user ID.

The SNMP community is not specified. Enter a SNMP community.

The password is invalid. Re-enter a password.

Enter the LDEV in the correct format. The format of the LDEV entry is invalid.

The format of the total capacity entry is invalid. Enter an integer value.

Revise and re-enter the total capacity.

You can enter a value up to a maximum of 2 to the power of 31 minus 1.

Enter the number of storages. The number of storages is invalid.

Enter an integer value.

The find options are invalid. Enter a valid find option.

Enter the LDEVs.

Enter the total capacity.

Enter the number of storages.

Specify another LDEV number.

Enter LDEVs.

Enter the total capacity.

Enter the number of storages.

A device cannot be found with the selected LDEV number <LDEV-

number>.

There are no or not enough LDEVs matching the search criteria.

Select more than one PORT.

Select more than one PORT-

HOST:WWN/iSCSI Name.

Select more than one LU.

Select more than one LU-PORT-

HOST:WWN/iSCSI Name connection.

An LDEV with a path specified cannot be specified for a LUSE.

An LDEV reserved as a Migration LDEV cannot be specified for a LUSE.

If CVS LDEVs are in a LUSE, all LDEVs must be CVS.

All LDEVs in a LUSE must have the same CU.

All LDEVs in a LUSE must have the same emulation type.

All LDEVs in a LUSE must have the same RAID level.

Specify another find option.

Select more than one PORT.

Select more than one Port-

Host:WWN/iSCSI Name.

Select more than one LU.

Select more than one LU-Port-

Host:WWN/iSCSI Name connection

Select unallocated LDEVs.

Select LDEVs which are not reserved for Volume Migration (Hitachi USP),

CruiseControl (Hitachi Lightning

9900V), or HIHSM (Hitachi Lightning

9900).

Make all the LDEVs either CVS LDEVs or non-CVS LDEVs.

Select LDEVs from the same CU.

Select LDEVs having the same emulation type.

Select LDEVs having the same RAID level.



1-135

Error Code

KAIC10210-E

KAIC10211-E

KAIC10212-E

KAIC10213-E

KAIC10214-E

KAIC10215-E

KAIC10216-E

KAIC10218-E

KAIC10219-E

KAIC10220-E

KAIC10221-E

KAIC10222-E

Description

All CVS LDEVs in a LUSE must have the same size.

The sum total of the LU size must be less than 2 TB.

The RAID0 LDEV cannot be specified in a LUSE.

All LUs must belong to the same default port controller in a LUSE.

Only a maximum of 36 LDEVs may be configured in a LUSE.

Storage cannot be added to the selected logical group.

No subsystems are registered.

A WWN already assigned to the port is selected. Check the available

HOST:WWN and PORT combinations.

Storage which is not a LUSE volume is selected.

Enter your user ID.

Enter your password.

The user ID or password is invalid.


Select LDEVs having the same size.

Make the sum total of the LU size less than 2 TB.

Select LDEVs except RAID 0 level

LDEVs.

Select LDEVs having the same port controller.

Select no more than 36 LDEVs.

Select another logical group.

Add a storage subsystem.

Check the available combinations of

HOST:WWN and PORT.

Select a LUSE volume.

Enter your user ID.

Enter your password.

Enter your user ID and password.



Error Code

KAIC10224-E

KAIC10225-E

Description

An error occurred in Single Sign On

Service.

Your session is over. Log out, and then log in again.


For LDAP:


2. By using the hcmdsldapuser command, check that the information for the server names specified in the auth.server.name attribute in exauth.properties is registered.

3. If StartTLS is used, check the SSL settings.

4. If you cannot resolve the problem, collect maintenance information, and then contact the Support

Center.

For RADIUS:


2. By using the hcmdsradiussecret command, check that the information for the server names specified in the auth.server.name attribute in exauth.properties is registered.


Center.

For Kerberos:

1. By using the host and port set in exauth.properties, check whether the authentication server can be accessed, the settings of the external authentication server, and the status of the network.


Center.

For not LDAP, not RADIUS and not

Kerberos:


Log in again.



1-137

1-138

Error Code

KAIC10226-E

KAIC10227-E

KAIC10228-E

KAIC10229-E

KAIC10231-E

KAIC10232-E

KAIC10236-E

KAIC10237-W

KAIC10238-W

KAIC10239-W

KAIC10240-E

KAIC10241-E

KAIC10242-E

KAIC10243-E

KAIC10244-E

KAIC10245-E

KAIC10246-E


The temporary license has expired.

Enter a product license key or a product license key file.

The emergency license has expired.

Enter a product license key or a product license key file.

Enter your license key.

An attempt to get the license information has failed.

This license key is invalid or has already been registered.

Purchase a license.

Enter your license key.


Enter a valid license key.

An attempt to log into Device Manager has failed. Enter the user ID and password.

Log in again.

The host has no copy pair information. Select a host that has one or more copy pairs.

If this operation is performed during

I/O processing on the primary volume, the data of the secondary volume may be corrupted. Make sure that no I/O processing is being performed on the primary volume before you proceed.

Are you sure you want to continue?

An un-recommended value is specified for the copy pace. Make sure the value is correct. Are you sure you want to continue?

Confirm that hosts are not issuing I/Os on any primary volume (P-VOL), and then continue the operation.

For AMS/WMS, Thunder 9500V or

Thunder 9200, set the copy pace for

ShadowImage, TrueCopy and

QuickShadow / COW Snapshot to

Faster 15.

The data in the volume specified to be the secondary volume will be lost as a result of this operation. Please confirm.

World Wide Name or iSCSI Name is not specified.

The name of the storage subsystem is not specified.

Select more than one WWN or iSCSI

Name or WWN group.

The specified parent logical group is invalid.

The host name must be unique.

World Wide Name(s) or iSCSI

Name(s) <World-Wide-Name/iSCSI

Name> is/are already in use by host(s) <host-name>.

<host-name> HORCM <instance-

number> cannot be specified, since it is not set to be managed.

Continuing this operation will delete the data of a volume specified to be a secondary volume. Back up the data if necessary, and then continue the operation.

Enter a World Wide Name or iSCSI

Name.

Enter the name of the storage subsystem.

Select a WWN or iSCSI Name or a

WWN group.

For a parent logical group, do not specify a logical group that will be updated or a child logical group of a logical group that will be updated.

Enter another host name.

Enter another World Wide Name or iSCSI Name.

Enter another instance number.



Error Code

KAIC10247-E

KAIC10248-E

KAIC10249-E

KAIC10250-E

KAIC10251-E

KAIC10252-E

KAIC10253-E

KAIC10254-E

KAIC10255-E

KAIC10256-E

KAIC10257-E

KAIC10258-E

KAIC10260-E

KAIC10263-E

KAIC10264-E

Description

The port number does not match the one already specified for <host-

name> HORCM <instance-number>.

The combination of the HORCM instance and the HORCM port number cannot be changed.

This group name already exists in the host <host-name> HORCM <instance-

number>.

The port number <port-number> is already used in the host <host-

name>.

The same HORCM cannot be specified for both P-VOL and S-VOL.

The same HORCM port cannot be specified for both P-VOL and S-VOL.

The LU <DevNum> cannot be deleted, because it is set as a command device.

The LU <DevNum> cannot be deleted, because it is set as a copy pair.

The LU <DevNum> cannot be deleted from Device Manager.

The LU <DevNum> cannot have a logical group moved.

The storage of another storage subsystem is assigned to the group

<group-name>.

You cannot assign the same security for all the LDEVs that you selected.

The LU <DevNum> cannot be secured with Device Manager.

A request cannot be received. Close the dialog box, and retry the operation. If the problem re-occurs, log in again and retry the operation.

Use numeric characters for the

HORCM instance number.

Use numeric characters for the port number

Secure the LUN from the application attached to the storage subsystem.

Close the dialog and try the operation again.


Select another combination, or create a new combination.

Enter another group name.

Enter another port number.

Enter another HORCM.

Enter another HORCM port.

Cancel the setup of the command device.

Delete a copy pair.

Delete from the application attached to the storage subsystem.

When an expanded LU is made by Disk

Array Management Program 2 with multiple LUs that have been allocated for an LUN, or when LUNs are assigned to LUs except for a MainLU after making the LU expansion, the

LUNs except for the LUNs allocated to the MainLU are also displayed by

Device Manager. In this case Device

Manager cannot operate this type of

LU.

Select another logical group.

Secure the security individually.

Enter a valid instance number.

Enter a valid port number.



1-139

1-140

Error Code

KAIC10265-E

KAIC10266-W

KAIC10267-E

KAIC10268-E

KAIC10269-E

KAIC10270-W

KAIC10271-W

KAIC10272-W

KAIC10273-W

KAIC10274-W


Only alphanumeric characters and symbols can be used in copy pair names and copy group names. Also, '-

' cannot be used at the beginning of a name.

Because LUNs are already assigned to the following combinations of LDEVs and Ports, this operation does NOT assign LUNs to them and does NOT register them to the storage group.

Are you sure you want to continue?

The selected WWN Group is not registered in the selected port. Check the available combinations of

HOST:WWN and PORT.

The selected LU is already allocated to the selected port. Check the available combinations of LU and Port-Host

WWN.

The selected LU is already allocated to the selected Port/HSD(iSCSI Target).


LU and Port-Host WWN/iSCSI Name.

As a result of this operation, data on these volumes will be lost. Are you sure you want to continue?

Confirm that no host and External port is performing I/O processing on any of the LUNs with the PORTs. If I/O processing is being performed, the processing might terminate abnormally. Are you sure you want to continue?

Confirm that no host and External port is performing I/O processing on any of the LUNs with the HSD/iSCSI Target.

If I/O processing is being performed, the processing might terminate abnormally. Are you sure you want to continue?

Confirm that no host and External port is performing I/O processing on any of the LUNs. If I/O processing is being performed, the processing might terminate abnormally. Are you sure you want to continue?

This operation will change the port's

LUN security, which may prevent other hosts and External ports from accessing LUNs with the following ports. Are you sure you want to continue?

Enter a valid pair name.

Enter a valid character string.


HOST:WWN and PORT, and use an available combination.


LU and Port-Host WWN, and use an available combination.


LU and Port-Host WWN/iSCSI, and use an available combination.

Check the contents of the warning and check whether there is an error in the operation.




Error Code

KAIC10275-W

KAIC10276-E

KAIC10277-E

KAIC10278-E

KAIC10279-E

KAIC10281-E

KAIC10282-E

KAIC10284-E

KAIC10285-E

KAIC10286-E

KAIC10287-W

KAIC10288-E

KAIC10289-E

KAIC10290-E

Description

Deleting copy pair volumes or command devices may disable later modification of the copy pair volume settings. Are you sure you want to continue?

The host <host-name> is not a host that can operate copy pairs.


A selected LDEV does not satisfy requirements for the copy pair.

Possible reasons for this error are as follows:

1. A requirement for making a copy pair was not satisfied.

2. An LDEV that meets the requirements for making a copy pair has not been selected.

See "Requirements for copy pairs", and make sure that the copy pair satisfies the necessary requirements for making a copy pair.

Specify a group name.

Specify the <P-VOL or S-VOL> <Item

Name>.

<Name> can only contain numeric characters.

Specify the <name> using a number between <number> and <number>.

A device already allocated to all ports is included.

A WWN group and WWN registered to a WWN group cannot be selected.

The selected WWN is registered to the

WWN group in the selected port.


HOST:WWN and PORT.

The LDEV cannot be specified because an invalid LDEV is selected or multiple

LDEVs are selected. The initial window of Dynamic Link Manager is displayed.

Add a subsystem.

Check the contents of the warning.

A resource group is registered in the specified logical group.

Check the following items:

1. The version of the RAID Manager installed on the host.

2. The version of the host agent installed on the host.

3. A command device is accessible by the host.

Select an LDEV that meets the requirements and execute the process again.

Enter valid characters.

Use numeric characters.

Enter another number.

Select a device that can be allocated.

Select a WWN that is not registered to the selected WWN group.


HOST:WWN and PORT, and use an available combination.

Re-select the LDEV, or select an LDEV in Dynamic Link Manager.

Add a storage subsystem before displaying the report window.

Check the contents of the warning, then select the check box.

Create a new logical group, then add a path in the logical group.



1-141

1-142

Error Code

KAIC10291-E

KAIC10292-E

KAIC10293-E

KAIC10294-E

KAIC10295-E

KAIC10296-E

KAIC10298-E

KAIC10299-E

KAIC10300-E

KAIC10301-E

KAIC10302-E

KAIC10303-E

KAIC10304-E

KAIC10305-E

KAIC10306-W

KAIC10307-E


The operation cannot be continued because no host is registered.

An attempt to perform authentication has failed.

An attempt to start has failed.

Register a host.

Contact the system administrator.

No path is selected.

An LDEV in pool cannot be used for storage allocation.

The LDEV device specified by the

LDEV number <LDEV-number> is part of a pool.

A communication error has occurred.

Open the Tasks menu, and confirm that the operation has finished.

Confirm that you are using a JRE version that is supported for use with

Web Client.

If the error occurs again, contact the system administrator.

Select a path.


Specify the LDEV number of an allocatable device.

An illegal transition was done by user operation.

The session is over. Log out, and then log in again.

The session is invalid. Log out, and then log in again.

All the paths that you have specified already exist. Specify other LDEVs and ports.

In QuickShadow / COW Snapshot, a

Restore operation cannot be performed in a batch for multiple copy pairs with the same P-VOL.

Select the alert to be deleted.

No logical groups are registered. Add a logical group, and then execute the operation.

The storage subsystem "<subsystem-

name>" has two controllers, but only one IP Address was specified. We recommend that you specify another

IP Address by modifying the properties in the Subsystem

Management window.

Enter the appropriate characters as follows: <string>. The maximum text length is <number> characters.

Open the Tasks menu to check if the operation has finished. If this error occurs frequently, contact the system administrator.

Retry the operation.

Log out, and then log in again.

Specify other LDEVs and ports.

Select one copy pair from the copy pairs with the same P-VOL to perform the restore operation.

Select the alert to be deleted.

Add a logical group before executing the operation.

Specify another IP Address by modifying the properties in the

Storage Subsystem Management window.

Check valid characters and text length.



KAIC10319-E

KAIC10320-E

KAIC10321-E

KAIC10322-E

KAIC10323-E

KAIC10324-E

KAIC10325-E

KAIC10326-E

KAIC10327-E

Error Code

KAIC10309-W

KAIC10310-E

KAIC10311-E

KAIC10312-E

KAIC10313-E

KAIC10314-E

KAIC10315-E

KAIC10316-W

KAIC10317-W

KAIC10318-W

Description

Update the current Javascript to the latest version.

Select one or more World Wide

Names.

The selected storage is deleted.

The group name "LUN SCAN" is reserved. Change the group name to execute this operation.

A LUSE cannot be created by mixing an internal volume with an assigned volume of <pp-name>.

All LDEVs in a LUSE must be the same

IO Suppression mode.

All LDEVs in a LUSE must be the same

Cache mode.

A host that corresponds to the

External port of a subsystem cannot be removed.

An assigned volume of <pp-name> may be invalid. Are you sure you want to continue?

An attempt was made to create a

LUSE with multiple external subsystems or an unknown external subsystem. (LDEV = <LDEV-

number>)

Provisioning Manager failed to invoke

Device Manager. (info: <info>)

Provisioning Manager sent an invalid request. (info: <info>)

The license key file that was entered is invalid.

Enter your license key file.

Failed to delete the file.

One or more application files are corrupt.

The license key file exceeds the maximum size.

This license key file is invalid or has already been registered.

All the LU types in a LUSE must be the same.


Install Internet Explorer 6.0 or later version, or you can download the latest JScript from the site below and install it. http://www.microsoft.com/downloads/ details.aspx?displaylang=en&FamilyID

=c717d943-7e4b-4622-86eb-

95a22b832caa

Specify the World Wide Names to delete.

Select another storage.

Change the group name using "Modify

Properties".

Select internal volumes only, or assigned volumes only.

Select LDEVs with the same IO

Suppression mode.

Select LDEVs with the same Cache mode.

A host that corresponds to the

External port of a storage subsystem cannot be removed from the system.

A volume assigned by Universal

Volume Manager may be invalid.

Check the changes.

A LUSE with multiple external subsystems is not recommended.

Select LDEVs with the same external subsystem.


Enter the correct license key file, then retry.

Enter your license key file.

No action is required.

Contact the support center.


Make sure that all the LDEV types are the same.



1-143

1-144

Error Code

KAIC10328-W

KAIC10329-E

KAIC10331-E

KAIC10332-E

KAIC10333-W

KAIC10334-W

KAIC10335-W

KAIC10336-E

KAIC10337-E

KAIC10338-W

KAIC10339-E


Confirm that all hosts have been added into the host view before running a LUN Scan. After LUN Scan,

Device Manager creates new hosts that have WWNs/iSCSI Names associated with the LUNs and have not been added into the Host View. You will need to clean up these hosts after the attributes of them are updated when the Device Manager Agent reports information about them. Are you sure you want to continue?


The formats specified for LDEV attribute condition values do not match.

For >=, specify a value that is less than or equal to the value specified for

<=.

If a storage resource is associated with a different storage resource, a partitioned storage administrator will not be able to manage the storage resource.

If volumes from different cache resources are used to create a LUSE volume, the effectiveness of the cache partition might be reduced.

A LUSE volume that consists of volumes in different cache resources has been selected. This might reduce the effectiveness of the cache partition.

Device Manager has failed to open the

Web browser.

Make sure that the Web browser is running normally.

Make sure that the link to the Web browser is set up correctly.

Device Manager has failed to open the

Web browser.

Make sure that the Web browser is running normally.

Make sure that the path to Internet

Explorer is set up correctly.

An operation was performed while the subsystem was being updated.

The displayed information might not be the latest information.

The subsystem is being updated. After this update processing finishes, retry the operation.

Check all hosts in host view.


Specify the same format for LDEV attribute condition values.

For >=, specify a value that is less than or equal to the value specified for

<=.

Your setting might prevent a partitioned storage administrator from managing the storage resource. Make sure that this setting is appropriate.

Your setting might reduce the effectiveness of the cache partition.

Make sure that this setting is appropriate.

Your setting might reduce the effectiveness of the cache partition.

Make sure that this setting is appropriate.

Make sure that the link to the Web browser is set up correctly.

Make sure that the path to Internet

Explorer is set up correctly.

If a subsystem operation is executed during update processing, the operation might fail. After the update processing finishes, retry the operation.

After the update processing finishes, retry the operation.



Error Code

KAIC10340-E

KAIC10341-E

KAIC10342-E

KAIC10343-E

KAIC10344-E

KAIC10361-E

KAIC10362-E

KAIC10363-E

KAIC10364-E

KAIC10365-E

KAIC10366-E

KAIC10367-E

KAIC10368-E

KAIC10369-W


An attempt to execute license management has failed.

All the LU CLPRs in a LUSE must be the same.

An LDEV in a DM-LU cannot be used for storage allocation.

The LDEV device specified by the

LDEV number <LDEV-number> is part of a DM-LU.

Only a maximum of 128 LDEVs may be configured in a LUSE.

Memory for executing license management may be insufficient on the system running Device Manager.

Please confirm whether the memory is insufficient on the system. If this problem persists, contact customer support.

Make sure that all the LDEV CLPRs are the same.


Specify the LDEV number of an allocatable device.

Select no more than 128 LDEVs.

Enter the host storage domain name. Enter the host storage domain name.

The specified host storage domain name "<host-storage-domain-name>" is not available. This host storage domain name is already used by another host storage domain on the same port.

Change the name of the host storage domain to one that does not exist.

Close the Host Storage Domain Info panel. After the screen has been refreshed, retry the operation.

The operation is not possible because the Host Storage Domain Info panel is open or in the process of closing.

Close the Host Storage Domain Info panel. After the screen has been refreshed, retry the operation.

Link and launch for Storage Navigator

Modular is required for this operation.

Please manually install and configure it according to the instructions in the manual.

To use PhysicalView, a setting for linking with Storage Navigator Modular is necessary. Confirm that the corresponding storage subsystem is correctly registered in Storage

Navigator Modular.

If V-VOL LDEVs are in a LUSE, all

LDEVs must be V-VOL.

Make all the LDEVs either V-VOL

LDEVs or non-V-VOL LDEVs.

Log out, and then log in again. Authentication was refused when logging into the common component.

Log out, and then log in again.


The license that corresponds to the subsystem has not been registered.

Data on the array group <array-

group-number>, which is the target of this operation, will be lost. Make sure that the data is not necessary.


Register the license in the Version

Information of Device Manager panel.

Data on the array group that is the target of this operation will be lost.

Check the data and, if necessary, take a backup, and then continue the operation.



1-145

1-146

Error Code

KAIC10370-W

KAIC10371-W

KAIC10372-W

KAIC10373-I

KAIC10374-I

KAIC10375-I

KAIC10376-I

KAIC10377-E

KAIC10379-E

KAIC10380-E

KAIC10381-E

KAIC10382-E

KAIC10383-E

KAIC10385-E

KAIC10386-E

Description

If the settings for this port are changed, the storage might become inaccessible to the hosts and external ports that are currently accessing the storage.

The system will now be rebooted to apply the settings. I/O requests cannot be received during the reboot.

If the system is being used as an external subsystem, make sure that you execute the Disconnect

Subsystem operation on Storage

Navigator.

Make sure that I/O processing is not being performed from hosts or external ports that are using the port targeted for this operation. Performing this operation while I/O processing is being performed might damage the file system. Also, as a result of this operation, only the hosts and external ports that are set in the host storage domain <name-of-the-host-storage-

domain-ID0> will be able to gain access.

Register the license key.

License registration has finished.

The temporary license will expire in

<n> days on <date>.

The emergency license will expire in

<n> days on <date>.

An attempt to log into Device Manager has failed. For the user, allocate a resource group, and assign a Device

Manager permission other than Peer or assign a user management permission. Then log in again.

All LDEVs in a LUSE must have the same stripe size.

A JavaScript-enabled browser is required.

The temporary license has expired.

The emergency license has expired.

The combination of filter conditions is invalid.

Duplicate resource group names are not allowed.

The resource group was not found in the Device Manager database.


Thoroughly check the settings.

The system will now be rebooted to apply the settings. I/O requests cannot be received during the reboot.

If the system is being used as an external subsystem, make sure that you execute the Disconnect

Subsystem operation on Storage

Navigator.

Make sure that I/O processing is not being performed from hosts or external ports.

Register the license key.


Register the license before the expiration date.

For the user, allocate a resource group, and assign a Device Manager permission other than Peer, or assign a user management permission. Then, log in again.

Make sure all the LDEVs have the same stripe size.

A JavaScript-enabled browser is required.

Purchase a license.

If you filter using AND, you can specify no more than 2 LDEV attribute conditions. Each condition must have a different operator. You cannot specify multiple non-LDEV attributes.

Make sure that the resource group name is not a duplicate, then retry.

Make sure that the resource group name exists in the Device Manager database, then retry.



KAIC10391-E

KAIC10392-E

KAIC10393-E

KAIC10394-E

KAIC10395-E

KAIC10396-E

KAIC10397-E

KAIC10398-E

KAIC10399-E

KAIC10400-E

KAIC10401-E

Error Code

KAIC10387-E

KAIC10388-E

KAIC10389-E

KAIC10390-E

KAIC10402-E

KAIC10403-E

KAIC10404-E

KAIC10405-E

KAIC10406-E


The specified resource group cannot be added under this API version.

The specified user cannot be added under this API version.

The specified logical group is already being used by another resource group.

The specified resource group is already associated with another logical group.

A user is already registered in the specified resource group.

A resource group is registered under the specified logical group.

A resource group is registered in the specified logical group.

The logon user cannot modify own resource group and user role.

The resource group name is invalid.

Use name less than 25 bytes.

The built-in resource group cannot be deleted.

The own resource group cannot be deleted.

The built-in resource group cannot be modified.

The own resource group cannot be modified.

The specified group name is reserved.

It cannot be used.

The logon user who does not belong to any resource groups cannot use the function of the Device Manager.

An inconsistency with the common user information about resource group was detected.


Specify another logical group, then retry.

Remove the old association, then retry.

Remove all resource groups under the specified logical group, then retry.

Create a new logical group, and then add a path in the logical group.

Check the logon user authorization, then retry.

The resource group name is invalid.

Use name less than 25 bytes.

Check the resource group.

Try again with the user who can use the function of the Device Manager.

The Common Component may not contain the most current resource group information. Restart the Device

Manager Server.


The specified resource group is not registered in the common user information.

The specified resource group has already been registered in the common user information.

Missing parameter: Resource Group

<name>.

The resource group was not found in the Device Manager database.

The Resource Group "name" is required. Provide the missing parameter, then retry. If this problem persists, contact the Support Center.




1-147

1-148

Error Code

KAIC10407-E

KAIC10408-E

KAIC10410-E

KAIC10411-E

KAIC10412-E

KAIC10413-E

KAIC10414-E

KAIC10415-E

KAIC10416-E

KAIC10417-E

KAIC10418-E

KAIC10419-E

KAIC10420-E


The "group name" is invalid. Specify within 25 characters. Only alphanumeric characters and '-', '=',

'\', '`', ',', '.', '_' are permitted.

The license key that should be entered does not exist in the license key file.

The entered license key file is for another product. Please verify the license key file.

The operation is not possible because the Select WWN/iSCSI Name panel is open or in the process of closing.

Close the Select WWN/iSCSI Name panel and, after the window has been refreshed, retry the operation.

An LDEV selection is invalid. The LDEV

(LDEV number <dev-number>) is reserved as an OnDemand LDEV.

An LDEV selection is invalid. The LDEV

(LDEV number <ldev-number>) is reserved as a Migration LDEV.

An LDEV reserved as an OnDemand

LDEV cannot be used for storage allocation.

An LDEV reserved as a Migration LDEV cannot be used for storage allocation.

An LDEV reserved as an OnDemand

LDEV cannot be specified for a LUSE.

This host name is already used by a mainframe host.

Not all of the selected LDEV paths belong to the same logical group.

Select LDEV paths that belong to the same logical group.

Check the group name.


After the window has been refreshed, retry the operation.

Select a valid LDEV.

Please select an unused host name.

Use the CLI to check which mainframe host names are being used. For details about how to do this, see the CLI manual.

Clear the selection or use the Move

Storage function for the necessary

LDEV paths, so that all selected LDEV paths belong to the same logical group, and then retry the operation.

Some of the selected LDEV paths do not belong to a logical group. Select

LDEV paths that belong to the same logical group.

<number-of-selected-LDEV-paths>

LDEV paths are selected. A maximum of <maximum-number-of-selectable-

LDEV-paths> LDEV paths can be selected for the Add Like Storage function.

<number-of-selected-hosts> hosts are selected. A maximum of

<maximum-number-of-hosts> hosts can be removed.

Select a number of LDEV paths that does not exceed the maximum number of selectable LDEV paths, and then retry the operation.

Select a number of hosts that does not exceed the maximum number of hosts that can be removed, and then retry the operation.



Error Code

KAIC10421-W

KAIC10422-W

KAIC10423-W

KAIC10424-E

KAIC10425-W

KAIC10426-W

KAIC10427-I

KAIC10428-W


The temporary license will expire in

<n> days on <date>. Enter a product license key or a product license key file.

The emergency license will expire in

<n> days on <date>. Enter a product license key or a product license key file.

The copy pair cannot be created because the copy status of multiple copy pairs that use the same P-VOL cannot be specified as "Pair" in this subsystem.

"Restore" or "Resync" cannot be specified for an operation on multiple copy pairs, because the copy status of multiple copy pairs that use the same

P-VOL cannot be specified as "Pair" in the subsystem <subsystem-name>.

The value of the table.ldev.rowsperpage

property could not be acquired because an attempt to read the client.properties

file failed. In this case, the default values (25, 300) will be used for the number of rows displayed for a sortable table.

The value (<set-value>) specified for the table.ldev.rowsperpage

property in the client.properties

file is invalid. In this case, the default values

(25, 300) will be used for the number of rows displayed for a sortable table.

A value (<set-value>) has been specified for table.ldev.rowsperpage


file. <set-value> rows will be displayed for a sortable table.

The table.ldev.rowsperpage

property has not been specified in the client.properties

file. In this case, the default values (25, 300) will be used for the number of rows displayed for a sortable table.

Register the license before the expiration date.

When creating a copy pair, return to the Choose Pair(s) window, and then change the copy pair settings so that the same P-VOL is not used, or change the copy status of the existing copy pair to "Split" or "Simplex".

If changing the copy status for multiple copy pairs that use the same

P-VOL, use only one copy pair for which "Restore" or "Resync" is specified.

Confirm the following to make sure the application program can read the client.properties

file:





The client.properties

file exists.

You have permission to read the client.properties

file.




corrupted.

file is not

For details on the table.ldev.rowsperpage


file, see the

Configuration and Operation Guide.

Specify a valid value for the table.ldev.rowsperpage


file.

For details on this property, see the



Specify a valid value for the table.ldev.rowsperpage


file.





1-149

1-150

Error Code

KAIC10429-E

KAIC10430-E

KAIC10431-W

KAIC10432-W

KAIC10433-W

KAIC10434-I

KAIC10435-I

KAIC10438-E


An attempt was made to allocate

<number-of-LU-Port-Host:WWN-

combinations> LU - Port - Host:

WWN/iSCSI Name combinations. The upper limit for LUNs allocatable in one operation is 100 LUNs.

If you want to allocate more than the upper limit, execute multiple operations.

The user ID or the password is incorrect.

The value of the client.assignlun.upperlimit.enable

d

property could not be acquired because an attempt to read the client.properties

file failed. The default value (true) will be used.

The client.assignlun.upperlimit.enable

d

property has not been specified in the client.properties

file. The default value (true) will be used.

The value (<specified value>) specified for the client.assignlun.upperlimit.enable

d

property in client.properties

is invalid. The default value (true) will be used.


The upper limit can be set or released using the client.assignlun.upperlimit.enable

d


file.



Make sure that the user ID and the password exist.

Confirm the following to make sure the application program can read the client.properties

file:






file exists.

You have permission to read the client.properties

file.




corrupted.

file is not

For details on the client.assignlun.upperlimit.enable

d


file, see the Configuration and

Operation Guide.

Specify a valid value for the client.assignlun.upperlimit.enable

d


file.



Specify a valid value for the client.assignlun.upperlimit.enable

d


file.



No action is required. The client.assignlun.upperlimit.enable

d

property is set to true.

The client.assignlun.upperlimit.enable

d

property is set to false.

An attempt was made to allocate more than <number-of-LU-Port-

Host:WWN-combinations> LU - Port -

Host: WWN/iSCSI Name combinations. The upper limit for

LUNs allocatable in one operation is

100 LUNs.



The upper limit can be set or released using the client.assignlun.upperlimit.enable

d


file.





Error Code

KAIC10439-E

KAIC10440-E

KAIC10441-W

KAIC10442-W

KAIC10443-W

KAIC10444-I

KAIC10445-I

KAIC10446-E

KAIC10447-E

KAIC10448-E

KAIC10449-E

KAIC10450-W

KAIC10451-E

Description

This license key is either invalid or may be for another product.

The last path of an LU of the copy pair volume cannot be released.

The format of the entered capacity is invalid.

The length of the value specified for the capacity is invalid. Specify a character string from 1 to 9 characters.

The value (<specified-value>) specified for the property client.report.csv.format.escaped in the file client.properties is invalid. The default value (<true>) will be used.

The property client.report.csv.format.escaped in the file client.properties is set to true.

The property client.report.csv.format.escaped in the file client.properties is set to false.

The operation is not possible because the Select Journal Group panel is open or in the process of closing. Close the

Select Journal Group panel. After the screen has been refreshed, retry the operation.

The LUN IDs available after the specified first LUN ID are insufficient.

Change the first LUN ID to a smaller number, and try again. (Port (HSD) =

<Port-(HSD)-name>)

The LDEV (number <LDEV-number>) has the <VolumeAttr> attribute.

A path cannot be set for an LDEV that has the <VolumeAttr> attribute.

The search condition specified in [Find

Storage] might not execute correctly because the specified number of

LDEVs exceeds the maximum

(<Number of LDEVs> ) that can be processed at one time. Using [Enter

LDEVs] or [Browse LDEVs], please select a lower number of storage subsystems for the operation.

The number of specified LDEV(s) exceeds the maximum (<maximum-

number-of LDEVs>) that can be specified at once. Divide the operation into two or more operations so that the specified number of LDEVs for each operation does not exceed the above maximum.


Enter a valid license key.

Cancel a copy pair volume and delete a path. For V-VOL, delete the path from Physical View.

Enter the capacity in the correct format.

Specify a valid value for the property client.report.csv.format.escaped in the file client.properties.




Close the Select Journal Group panel.

After the screen refreshes, retry the operation.

The LUN IDs available after the specified first LUN ID are insufficient.

Change the first LUN ID to a smaller number, then retry.

Please select a valid LDEV.

Select a device that can be assigned.

Please select the storage subsystems by using Enter LDEVs or Browse

LDEVs.

If you need to specify a number of

LDEVs that exceeds the maximum for a single operation, divide the operation into several operations.



1-151

1-152

Error Code

KAIC10452-W

KAIC10453-E

KAIC10454-E

KAIC10455-E

KAIC10456-E

KAIC10457-W

KAIC10460-E

KAIC10461-E

KAIC10462-W

KAIC10463-E

KAIC10465-E

KAIC10466-I

KAIC10467-E

KAIC10468-E


The maximum number of search data items that can be displayed has been reached (2048). If required data is not displayed, please divide the operation into several smaller operations.

The storage subsystem information might not be up-to-date. Refresh the storage subsystem information, and then re-execute the operation.

(subsystem: <subsystem-name>)

Enter the iSCSI Target.

The specified iSCSI Target "<iSCSI-

Target>" is not available. This iSCSI

Target is already used by another iSCSI Target on the same port.

If required data is not displayed, please divide the operation into several smaller operations.


If you do not refresh the storage subsystem, you might not be able to operate storage subsystems.

The storage subsystem information might not be up-to-date. Restart the

Device Manager server, and then reexecute the operation.

The format of the entered Consumed

Capacity is invalid.

The length of the value specified for the Consumed Capacity is invalid.

Specify a character string from 1 to 9 characters.

The specified operation cannot be performed because the storage subsystem is not supported by Device

Manager.

The execution for start command of

<command-name> failed.

The execution for stop command of

<command-name> failed.

Restart the Device Manager server, then retry.

If you do not restart the Device

Manager server, the contents displayed in sortable tables might become incorrect.

Enter the Consumed Capacity in the correct format.

Unsupported storage subsystems can only be deleted. Other operations are not supported.

Start the Device Manager Server.

Stop the Device Manager Server.

The number of LDEVs exceeds the maximum (Number of LDEVs) that can be processed at one time. Please change and rerun a search option, or using [Enter LDEVs] or [Browse

LDEVs] and choose storage to operate other LDEV(s).

The operation is not possible because the iSCSI Target Info panel is open or in the process of closing. Close the iSCSI Target Info panel. After the screen has been refreshed, retry the operation.

Please change and rerun a search option, or using Enter LDEVs or

Browse LDEVs and choose storage to operate other LDEV(s).

Close the iSCSI Target Info panel.

After the screen has been refreshed, retry the operation.

The length of the value specified for the array group is invalid. Specify a character string from 1 to 20 characters.

Enter the array group in the correct format.

Core License registration has finished. No action is required.

Enter the iSCSI Target.

Change the name of the iSCSI Target to one that does not exist.



Error Code

KAIC10469-E

KAIC10470-E

KAIC10471-E

KAIC10472-E

KAIC10473-E

KAIC10474-E

KAIC10475-W

KAIC10476-E

KAIC10477-E

KAIC10478-W

KAIC10479-E

KAIC10480-E

KAIC10481-E

KAIC10482-E

KAIC10483-E

KAIC10484-E

KAIC10485-E

KAIC10486-E


Select one or more iSCSI Names.

The specified iSCSI Name is invalid.

The iSCSI Name must be unique.

License registration of Web Client has finished, but there is a possibility that licensing info acquisition handling of

Device Manager Server failed.

There is a possibility that licensing info acquisition handling of Device

Manager Server failed.

An error was encountered during task execution. Please see error code and message below for details. Click the

Back button to modify task parameters, if needed, and re-submit the task for execution.

A LUN exists whose security does not match the security of the host storage domain/iSCSI target.

Different type of A WWN/iSCSI Name and port are selected. Check the available HOST:WWN/iSCSI Name and

PORT combinations.

Paths that have different port types are selected. Select paths that have the same port type.

A path cannot be added because the type of an entered WWN or iSCSI

Name is different from the type of a

WWN or iSCSI Name already set for the host. To add a path to a WWN or iSCSI name, use the Add Storage function.


Specify the iSCSI Names to delete.

Enter a valid iSCSI Name.

Enter another iSCSI Name.

Log in again. If this problem persists, contact the Support Center.

Log in again. If this problem persists, contact the Support Center.

Please see error code and message below for details. Click the Back button to modify task parameters, if needed, and re-submit the task for execution.


Make sure that the combination of

WWN (or iSCSI name) and port is valid.

Select paths that have the same port type.

To add a path to a WWN or iSCSI name, use the Add Storage function.

An error occurred in the Storage

Navigator Modular 2. (error code =

"<error code>")

No usable pools are registered.

The length of the value specified for the host is invalid. Specify a character string by using to 50 characters.

Collect maintenance information, and then contact customer support.


Register a pool.

Enter the host in the correct format.

The format of the host entry is invalid.

The format of the array group entry is invalid.


No mapping path is selected.

No LDEV number is entered. Enter the

LDEV number.

Select at least one mapping path.

Enter the LDEV number.



1-153

1-154

Error Code

KAIC10487-E

KAIC10488-E

KAIC10489-E

KAIC10490-E

KAIC10491-E

KAIC10494-E

KAIC10495-E

KAIC10496-E

KAIC10497-W

KAIC10498-E

KAIC10500-E

KAIC10501-E

KAIC10502-E


The format of the entered LDEV number is invalid. Enter either "Auto" or an LDEV number.

No array group is entered. Enter the array group.

The format of the entered array group is invalid. Enter either "Auto" or a value from 1 to 16384.

Enter the CLPR number.

The format of the entered CLPR number is invalid. Enter a numeric value from 0 to 2147483647.

Duplicate LDEV numbers exist. Please specify a unique LDEV number.

The number of specified LDEVs exceeds 100, the maximum number that can be specified at once. If you want to perform an operation using more than the maximum number of

LDEVs, perform the operation a number of times, specifying a valid number of LDEVs each time.

The number of items selected for the mapping path has exceeded the maximum number of selectable items.

You can specify a maximum of 8 items.

You can combine from 1 to 8 external array nodes and ports. Click the appropriate LDEV number, and then change the number of combinations.

External storage settings cannot be specified for this storage subsystem.

(microcode version = version-number)

An attempt to connect to the database has failed. Make sure the database has been started.

Enter the LDEV number in the correct format.

Enter the array group.


Enter the CLPR number.

Enter the CLPR number in the correct format.

Specify a unique LDEV number.

If you want to perform an operation using more than the maximum number of LDEVs, perform the operation a number of times, specifying a valid number of LDEVs each time.

Change the number of items selected for the mapping path to 8 or fewer.

Click the appropriate LDEV number, and then change the number of combinations.

Select a storage subsystem for which the settings can be specified.

If the database has not been started, re-start it, then retry.

If the database has been started, there might be an internal error.


An attempt to acquire data from the database has failed. Make sure the database has been started. SQL statement: SQL statement

The file could not be opened. Make sure the file/directory access permissions and path name are correct, and that there is enough free space in the filesystem. File name: file

name

Make sure the file/directory access permissions and path name are correct, and that there is enough free space in the filesystem.

If there is not enough free space in the file system, delete any unnecessary files, then retry.



Error Code

KAIC10503-E

KAIC10504-E

KAIC10505-E

KAIC10506-E

KAIC10507-E

KAIC10508-W

KAIC10509-W

KAIC10510-W

KAIC10511-E

KAIC10512-E

KAIC10513-E

KAIC10514-E

KAIC10515-E

KAIC10516-E


An attempt to write the file has failed.

Make sure the file/directory access permissions are correct, and that there is enough free space in the filesystem. File name:file name

An attempt to read the file has failed.

Make sure the file/directory access permissions are correct, and that there is enough free space in the filesystem. File name: file name

An attempt to delete the file has failed. Make sure the file/directory access permissions are correct. File name: file name

The size of the detailed array report is more than 2 gigabytes. Reduce the number of selected storage subsystems, and then try again.

An attempt to perform a cancellation has failed. The status of the detailed array report has already changed to

"error" or "incomplete", or else the detailed array report has already been deleted.

Another request to create a detailed array report is currently being executed. Please wait for a while.

There are too many LDEVs, so it might not be possible to display reports. If they cannot be displayed, use the detailed array report.

After downloading the detailed array report, delete it from the server.

The status of the detailed array report is "incomplete". File name: file name

The detailed array report was deleted.

File name: file name


An attempt to acquire the Storage

Navigator Modular tree information has failed.

There are no available LDEVs.

The specified pool cannot be deleted because a virtual volume is assigned to it.

Make sure the file/directory access permissions are correct to enable the user executing the operation to write the file, then retry.

If there is not enough free space in the file system, delete any unnecessary files, then retry.

Make sure the file/directory access permissions are correct to enable the user executing the operation to read the file, then retry.

Make sure the file/directory access permissions are correct to enable the user executing the operation to delete the file, then retry.

Reduce the number of selected storage subsystems, then retry.

Cancellation can only be performed when the status is "processing". If the status is any other status, cancellation cannot be performed. Close the window, by clicking the close button.

Wait until the status of the detailed array report being processed changes to another status, then retry.

Sometimes HTML output cannot be performed if there are too many

LDEVs. From the report list, use the detailed array report.

The detailed array report is retained on the server even after it is downloaded. We recommend deleting it from the server as soon as possible.

There is a possibility of an internal error. Please contact the Support

Center.

If you need a detailed array report, try the operation again.

Click the [Refresh Tree] button, and then display the navigation area again.


Provide LDEVs which can be registered to the pool.

Delete any virtual volumes assigned to the specified pool.



1-155

1-156

Error Code

KAIC10517-E

KAIC10520-E

KAIC10521-E

KAIC10522-E

KAIC10525-E

KAIC10526-E

KAIC10527-E

KAIC10528-E

KAIC10551-E

KAIC10560-E

KAIC10561-E

KAIC10562-E

KAIC10563-E

KAIC10564-E

KAIC10565-E

KAIC10566-E

Description

A virtual volume cannot be deleted because a path is set to a <PP-name> virtual volume (LDEV number =

<LDEV-number>).

A license for <PP-name> is not registered in the storage subsystem.

There are no available pool IDs.


Check the virtual volume, and then retry the operation.

Install the license for <PP name> into the storage subsystem.

Delete any unnecessary pools, and then retry the operation.

If you want to delete more than the maximum number of pools, execute multiple operations.

An attempt was made to delete

<number-of-pools-selected> pools. A maximum of <set-maximum> pools can be deleted in one operation. If you want to delete more than the maximum number of pools, execute multiple operations.

An attempt was made to delete

<number-of-virtual-volumes-

selected> <PP-name> virtual volumes. A maximum of <set-

maximum> virtual volumes can be deleted in one operation. If you want to delete more than the maximum number of virtual volumes, execute multiple operations

An operation is not possible because the editing window is open or in the process of closing. Close the editing window, wait for the window to be refreshed, and then retry the operation.

Multiple virtual volumes are specified.

Specify only one virtual volume.

All LDEVs registered to a pool must have the same CLPR.

The subsystem managed by the partitioned storage administrator cannot execute the operation.

Two or more LDEVs are selected.

Please select only one LDEV.

Select an LDEV for which you want to create a LUSE.

The total LU size must be less than 60

TB.

A command device LDEV cannot be specified for a LUSE.

An LDEV whose access attribute is guarded cannot be specified for a

LUSE.

An LDEV used as a Pool Volume cannot be specified for a LUSE.

An LDEV used as a Journal Volume cannot be specified for a LUSE.

If you want to delete more than the maximum number of virtual volumes, execute multiple operations.

Close the editing window, wait for the main window to be refreshed, and then retry the operation.

Specify only one virtual volume.

Revise the LDEV specification, and then retry the operation.

Revise the subsystem settings.

More than two LDEVs are selected.

Please select only single LDEV.

Select single LDEV for which you want to create a LUSE.

Specify less than 60 TB for the total

LU size.

Select an LDEV that is not a command device.

Select an LDEV whose access attribute is not guarded.

Select an LDEV that is not a pool volume.

Select an LDEV that is not a journal volume.



Error Code

KAIC10567-E

KAIC10568-E

KAIC10569-E

KAIC10570-E

KAIC10571-E

KAIC10572-E

KAIC10573-W

KAIC10574-E

KAIC10575-E

KAIC10576-E

KAIC10577-W

KAIC10601-E

KAIC10602-E


An LDEV used as a <PP name> virtual volume cannot be specified for a

LUSE.

An LDEV used as a Pair Volume cannot be specified for a LUSE.

An LDEV assigned to a host storage domain whose host mode is "VMware" cannot be specified for a LUSE.

An LDEV assigned to a host storage domain whose host mode is

"Windows" cannot be specified for a

LUSE.

There are no LDEVs that can be used to make a LUSE.

Not all of the selected LDEV paths belong to the same storage subsystem. Select LDEV paths that belong to the same storage subsystem.

As a result of this operation, data on volumes that do not have paths specified (volumes marked with "*" in the Object List) will be lost. Are you sure you want to continue?

Some of the selected LDEV paths are allocated to the same ports,

HSD/iSCSI targets, or hosts. Check the ports, HSD/iSCSI targets, and hosts of these paths.

The microcode version of this storage subsystem does not support LUSE operations on LDEVs that have paths specified.

Some of the selected LDEV paths are allocated to the same ports, WWN, or hosts. Check the ports, WWN, and hosts of these paths.

Before performing this operation, check the settings of the host and host storage domain of the target path. The host might not recognize the expansion of the volume by this operation.

The number of specified LDEVs exceeds (<maximum-number-of-

LDEVs>), the maximum number that can be specified at once. If you want to perform an operation using more than the maximum number of LDEVs, perform the operation a number of times, specifying a valid number of

LDEVs each time.

Use any of the following characters for a label: <string>

Select an LDEV that is not a virtual volume.

Select an LDEV that is not a pair volume.

Select an LDEV that is assigned to a host storage domain whose host mode is not "VMware".

Select an LDEV that is assigned to a host storage domain whose host mode is not "Windows".

Please select an LDEV that can be used to make a LUSE.

Select LDEV paths that belong to the same storage subsystem.


Check the ports, HSD/iSCSI targets, and hosts of these paths.


Check the ports, WWN, and hosts of these paths.

To perform this operation, check the restriction of the host OS and host storage domain of the target path.

For details, see the LUN Expansion manual that corresponds to your storage subsystem.

If you want to perform an operation using more than the maximum number of LDEVs, perform the operation a number of times, specifying a valid number of LDEVs each time.

Enter only valid characters.



1-157

1-158

Error Code

KAIC10603-E

KAIC10604-E

KAIC10607-W

KAIC10608-W

KAIC10609-W

KAIC10610-E

KAIC10611-E

KAIC10612-E

KAIC10613-E

KAIC10614-E

KAIC10615-E

KAIC10616-W

KAIC10617-W

KAIC10618-E

KAIC10619-E

KAIC10620-E

Description

Use no more than <number> characters for a label.

A filter condition that is not compatible with LDEVs has been restored. Change "Not applicable" displayed in the list box to a valid value.

Are you sure you want to add the label to the selected volume(s)?


Enter no more than the allowed maximum number of characters.

Select a correct value from the list.

Are you sure you want to modify the labels for the selected volume(s)?

Are you sure you want to delete the labels from the selected volume(s)?

The storage subsystem configuration information might not be up-to-date.

Check the status of the storage subsystem information.


<Database name>. Call server administrator.

Available storage subsystems do not exist.

Before continuing, make sure that you want to add the label to the selected volume(s).

Before continuing, make sure that you want to modify the labels for the selected volume(s).

Before continuing, make sure that you want to delete the labels from the selected volume(s).

Close this dialog box, and then retry the operation.

A selected LDEV was not found. Close this dialog box, and then retry the operation.

Tiered Storage Manager failed to invoke Device Manager. (info: <info>)

Tiered Storage Manager sent an invalid request. (info: <info>)

Device Manager faild to invoke Tiered

Storage Manager. (info: <info>)

The length of the value specified for the label is invalid. Specify a character string by using to 64 characters.

The length of the value specified for the HSD/iSCSI Target is invalid.

Specify a character string by using to

32 characters.

The storage subsystem configuration information might have been updated.



Enter the label in the correct format.

Enter the HSD/iSCSI Target in the correct format.

Refresh the storage subsystem. If you do not refresh the storage subsystem, you might not be able to perform some operations on it.

Check the status of the storage subsystem.


Software registration managed by the

SMI-S provider might be invalid.

Please retry this action after adding a storage subsystem available for Host

Scan.

Revise the

CIM_RemoteServiceAccessPoint class on the SMI-S provider, refresh the storage subsystem, and then retry the operation.



Error Code

KAIC10621-E

KAIC10622-E

KAIC10623-W

KAIC10624-W

KAIC10625-I

KAIC10626-E

KAIC10627-E

KAIC10628-E

KAIC10629-E

KAIC10630-E

KAIC10631-E

KAIC10633-E

KAIC10634-E

KAIC10635-E

KAIC10637-E


The port number has not been specified.

Specify a valid port number.

The password has not been specified. Specify a valid password.

The client.addstorage.block.per.storage property has not been specified in the client.properties file. The default value

(true) will be used.

The value "specified-value" specified for the client.addstorage.block.per.storage property in the client.properties file is invalid. The default value (true) will be used.

The value "specified-value" has been specified for the client.addstorage.block.per.storage property in the client.properties file.

Specify a valid value for the client.addstorage.block.per.storage property in the client.properties file.

For details on this property, see the "

Configuration and Operation Guide".

Specify a valid value for the client.addstorage.block.per.storage property in the client.properties file.

For details on this property, see the "

Configuration and Operation Guide".


Wait for the user to finish, or for the user to cancel the processing.

This wizard, which is used for adding storage from a selected subsystem, is currently in use by another user. Wait for the user to finish, or for the user to cancel the processing.

All LDEVs registered in a pool must be of the same type.

The port number is invalid. Specify a number from 1 to 65,535.

All LDEVs registered in a pool must be of the same volume class (internal or external).

An attempt to acquire the storage subsystem information has failed.


Specify a number from 1 to 65,535.


Click the [Refresh Tree] button, and then display the screen again. If this problem persists, contact customer support.

Choose a valid WWN/iSCSI name for the host/port.

The HSD/iSCSI target might have been deleted from the selected host/port. Choose a valid WWN/iSCSI name for the host/port.

The license that corresponds to the subsystem has not been registered.

The valid Full License is not registered in Device Manager.

An invalid URL was detected. Confirm that the URL is correct.

{number-of-hosts-selected} hosts are selected. A maximum of {specified-

maximum} hosts can be selected.

Register the license in the dialog box for Device Manager License

Information.

Register the valid Full License in

Device Manager.

Confirm that the URL is correct.

Select no more than <set-maximum> hosts.



1-159

1-160

Error Code

KAIC10639-E

KAIC10640-E

KAIC10641-W

KAIC10642-W

KAIC10643-I

KAIC10647-I

KAIC10650-W

KAIC10651-E

KAIC10652-W

KAIC10657-E

KAIC10659-W


{number of WWNs/iSCSI names

selected} WWNs/iSCSI names are selected. A maximum of {specified-

maximum} WWNs/iSCSI names can be selected.

There are no hosts available to be merged.

The client.ldev.rowsperpage.retain.enabled property has not been specified in the client.properties file. The default value

(true) will be used.

The value (<specified-value>) specified for the client.ldev.rowsperpage.retain.enabled property in the client.properties file is invalid. The default value (true) will be used.

Select no more than <specified-

maximum> WWNs/iSCSI names.

Register the hosts that you want to merge, and then retry the operation.

Specify a valid value for the client.ldev.rowsperpage.retain.enabled property in the client.properties file.


Hitachi Device Manager and

Provisioning Manager Server

Installation and Configuration Guide.

Specify a valid value for the client.ldev.rowsperpage.retain.enabled property in the client.properties file.


Hitachi Device Manager and

Provisioning Manager Server

Installation and Configuration Guide.

No action is required. The value (<spedified-value>) has been specified for the <property-key> property in the client.properties file.

The capacity is currently within the licensed limit.

The capacity has exceeded the licensed limit.

An attempt to read properties in the

<property-file> file has failed. The default value (<default-value>) for

<property-key> will be used.



An attempt to read properties in the

<property-file> file has failed. The default value (<default-value>) for

<property-key> will be used.

A parameter for connecting to the specified storage subsystem (the IP address or the communication protocol) has been changed in Storage

Navigator Modular 2. From Storage

Navigator Modular 2, note the IP address and communication protocol, and then add the storage subsystem.

One or more host mode options supported by the storage subsystem could not be acquired.

Confirm the following to make sure the application program can read the file:







The file exists.

You have permission to read the file.

The file is not corrupted.

Confirm the following to make sure the application program can read the file:







The file exists.

You have permission to read the file.

The file is not corrupted.

From Storage Navigator Modular 2, note the IP address and communication protocol of the specified storage subsystem. After that, from the [Add Subsystem] dialog box in Device Manager, specify the same IP address and communication protocol, and then add the subsystem.




Error Code

KAIC10660-W

KAIC10661-E

KAIC10662-E

KAIC10663-E

KAIC10664-E

KAIC10665-E

KAIC10666-W

KAIC10667-E

KAIC10668-E


An operation was performed while the host was being updated.

The displayed information might not be the latest.

The host information might not be the latest. Check the status of the host.

An error occurred during a task. For details, see the error code and message below. Close the window, and then retry the operation.

The virtualization server or the virtualization-server management program could not be detected. The wrong IP address or protocol might have been specified, or the virtualization server or the virtualization-server management program might not be in a normal state.

The format of the IP address is invalid. Enter an IP address in one of the following formats:

- xxx.xxx.xxx.xxx (where xxx is a decimal integer from 0 to 255)

- yyyy:yyyy:yyyy:yyyy:yyyy:yyyy:yyyy

:yyyy (where yyyy is a hexadecimal integer from 0 to ffff).

The total LU size must be less than

128 TB.

Some virtual machine names could not be displayed because information on some virtual machines could not be acquired. Check the status of the virtual machines.

An error occurred in the processing of the Storage Navigator Modular 2 session. (Process status code from

<Process status code0> to <Process

status code1>.)

The pool (pool ID: pool number) might not be in the Normal status.

Threshold1 can be modified only when the pool is in the Normal status.

Refresh the storage subsystem information, and then check the status of the pool.

An operation might fail if it is executed on a host that is being updated. Wait until the update has finished, and then retry the operation.

Refresh the host, and then try again.

If you do not refresh the host, you might not be able to execute operations on the host.

For details, see the error code and message below. Close the window, and then retry the operation.

Depending on the cause, take either or both of the following actions:





Revise the IP address or protocol specification.

Correct the state of the virtualization server or the virtualization-server management program.

Enter an IP address in one of the following formats:

- xxx.xxx.xxx.xxx (where xxx is a decimal integer from 0 to 255)

- yyyy:yyyy:yyyy:yyyy:yyyy:yyyy:yyyy

:yyyy (where yyyy is a hexadecimal integer from 0 to ffff).

Specify less than 128 TB for the total

LU size.

Some virtual machine names could not be displayed because information on some virtual machines could not be acquired. Check the status of the virtual machines.

Retry the operation.

If you cannot resolve the problem, collect maintenance information, and then contact the Support Center.

Refresh the storage subsystem information, and then check the status of the pool.



1-161

Error Code

KAIC11999-E

Description

Memory might be insufficient or a network error might have occurred.

(details: <info>)


If the details or log contains the character string "Out Of Memory", memory is insufficient. In this case, set the memory heap size for HBase

Storage Mgmt Web Service.

If the details or log contains the character string "Connection", a network error might have occurred. In this case, check the network status.

If the problem is other than the above, contact the Support Center.



Device Manager Agent Messages

When an error occurs, Device Manager Agent produces one or more error messages. An error message consists of a message number, a level code indicating the severity of the error, and the error message text. Message numbers are grouped by error type. If you run Device Manager Agent in an

English environment, some messages are output in English, using the same meaning and error codes as for Japanese messages.

Device Manager Agent messages are written to a secondary output device in the following format:

revision-level / timestamp / message-text

revision-level indicates an internal revision number of the program. This information is required when an error is reported to the Hitachi Data

Systems Support Center.

timestamp, although subject to the local time zone, is always in the same format in other respects. In other words, there are no locality-specific format differences in a timestamp.

message-text begins with a message number followed by one of the following message levels indicating the severity:

–

I: Non-error information

–

W: Warning

– E: Error

Table 1-14 and Table 1-15 list the Hitachi Device Manager Agent error

messages and provide the recommended action for resolving the error conditions. The error messages are listed in numerical order by error code.

Table 1-14 KAIC20000-KAIC23999, KAIC25000-KAIC29999: Hitachi

Device Manager Agent Errors

Error Code

KAIC21901-E

KAIC21902-E

Description

server.properties was not found. server.properties could not be read.


The server.properties

does not exist.

file

Make sure that server.properties

exists, and that it is well-formed.

The server.properties

could not be read.

file

Make sure that server.properties

exists, and then re-execute the operation as a user with

Administrator permissions.



1-163

1-164

Error Code

KAIC21907-E

KAIC21908-E

KAIC21909-E

KAIC21910-E

KAIC22001-E

KAIC22003-E


server.properties could not be saved.

An attempt to save the server.properties

file has failed.

Make sure that the installation of Device Manager agent terminated correctly, and that the disk is not full.

The configuration of HiScan event could not be saved. The registration command returned exit code {code}.

Too many arguments have been specified.

Attempt to save the configuration of the HiScan event has failed.

Check the system configuration.

The hdvmagt_account arguments. command was executed with

Execute this command with no parameters.

Unable to change server.properties because Add-On module is currently running.

This usage is incorrect:

{<explanation > <summary of

correct usage>}

The hdvmagt_account command was executed while an add-on module on a

Device Manager agent was running.

After the add-on module processing finishes, reexecute the hdvamgt_account command.

An attempt was made to execute

HiScan parameters.

with invalid

Execute

HiScan

with the correct parameters.

An error occurred while executing the

HiScan command.

Respond as indicated in the message following

DoScan:

.

DoScan: Disk drive not found on this host


HiScan command.

Consult your system administrator. Ensure that all

Hitachi or Sun disks are online.


HiScan command.

Respond as indicated in the message following

DoEmit:

.



Error Code

KAIC22005-E

KAIC22006-E

KAIC22007-E

KAIC22008-E

KAIC22009-E

Description

The output file could not be opened.({Exception information})

The IPAddress [{IPAddress}] could not be resolved.

The server socket could not be opened. ({Exception information})

A connection could not be established.

An HTTP/XML message could not be sent. ({Exception

information},Content-

Length=Transmission length)


An attempt to create a log file that was specified with the

-t parameter has failed.

Ensure that the path used in the

-t

parameter exists, the filename is valid for this operating system, and that there is sufficient space on the disk.

An attempt to resolve the IP address of the Device

Manager server has failed.

Make sure that the IP address of the Device Manager server is correct.

An attempt to communicate with the Device Manager server has failed.

Make sure that the Windows

OS and TCP/IP protocol stack are correctly installed.


Make sure that the

-s parameter is specified correctly (both the server address and port number are correct), and the specified

Device Manager server is active.


Make sure that the network connection is operating reliably.

Make sure that the server.http.entity.maxLeng

th

property in the server.properties

file of the

Device Manager server is larger than Content-Length.



1-165

1-166

Error Code

KAIC22010-E

KAIC22011-E

KAIC22012-E

KAIC22013-E

Description

The server response could not be received. ({Exception




There was no response from the Device Manager server.

The Device Manager server is probably not working correctly.

Make sure that the value of the

-s

parameter indicates a

Device Manager server, and not another network server type.

Make sure that the network connection is operating reliably.


th


file of the


A connection to the Device Manager server was established, but no response was detected. ({Exception



The correct response header could not be acquired: HTTP/1.0.

Received:({Received contents})

The status code of the HTTP response is not "OK": ({Response contents})

Make sure that the value of IP

Address of the Device

Manager server specified in -s parameter or server.server.serverIPAddr

ess

property is correct, and the port of the Device

Manager server specified in

-s parameter or server.server.serverPort

property is correct (It is corresponding to server.server.serverPort

property of the Device

Manager server), the Device

Manager server works normally, and the network is normal.


The details portion of this message should indicate the nature of the problem. This kind of condition may be due to an invalid combination of

u

userid and

-p

password parameters.



Error Code

KAIC22014-E

KAIC22018-E

KAIC22019-E

KAIC22020-E

KAIC22047-E


HiScan could not connect to Device

Manager server because of a connection timeout.

Information about the installed plugin could not be acquired.({Exception

information})

The "hldutil" response timeout.

The executable program "hldutil" does not exist.({Exception information})

An attempt to authenticate a user ID and password has failed. : {status

code}

Communication with the

Device Manager server terminated because of a timeout monitored by Device

Manager agent.

Revise the server.http.server.timeOut

value in the Device Manager agent properties.


th


file of the


The installation status is incorrect.

The installation of Device

Manager agent or Dynamic

Link Manager may have terminated abnormally.

Consult your system administrator.

An abnormal situation may have occurred during execution of the hldutil command, or a timeout may have occurred in the hldutil command due to an excessive number of LUs.

Make sure that the host is detecting LUs correctly. If necessary, revise the value of server.util.processTimeOut

property.

If the problem cannot be resolved, consult your system administrator.

An attempt to execute the hldutil

command has failed.

The installation of Device

Manager agent may have terminated abnormally.

Consult your system administrator.

The specified user ID and password are invalid.

Execute the hdvmagt_account command to check the user

ID and password.



1-167

1-168

Error Code

KAIC22048-E

KAIC22049-E

KAIC22050-E

KAIC22051-E

KAIC22401-W

KAIC22801-I

KAIC22802-I

KAIC22803-I

KAIC22804-I

KAIC22805-I

KAIC22806-I


The data in the request was rejected because the data is too large. :

{status code}

The value of an argument in the specified option is invalid. : {option}

A site-local address or link-local address cannot be specified.

({address})

An attempt to resolve the host IP address failed.

The command prompt was not started by the administrator.

Although processing is executing properly, the started command prompt will be closed after processing ends.

The HiScan command will now start to send an XML document to the

Device Manager server at {IP-

ADDRESS}:{PORT-

NUMBER}(Content-


The HiScan command has finished sending an XML document to the


ADDRESS}:{PORT-NUMBER}

The HiScan command is receiving an

XML document from the Device

Manager server at { IP-ADDRESS }:{

PORT-NUMBER }

The HiScan command has finished receiving an XML document from the


ADDRESS}:{PORT-NUMBER}

The HiScan command will now start to acquire HostVolume information.

The HiScan command has finished acquiring HostVolume information.

No additional action is required.

The Device Manager server's processing capacity was exceeded because the data in the request is too large.

Revise the value of the Device

Manager server property server.http.entity.maxLeng

th

.

The character that cannot be used for the argument of the option is specified.

Specify the character string that can be used for the argument of the option.

A site-local address or linklocal address is specified in an option. To use IPv6 addresses, you must specify a global address.

Check, and if necessary, revise the value set for server.http.socket.agentAddre

ss in server.properties.

If this error occurs repeatedly, contact the

Support Center.

Execute this command as the administrator.



Error Code Description Recommended Action

KAIC25105-W

You can not select this destination folder. Recommended folder is under

"Program Files (x86)".

KAIC25107-W You cannot cancel this installation operation: [type of installation]

KAIC25111-W (Windows)

The Device Manager agent installation has been suspended due to requests received from a management server.

Please wait a moment and then click

Retry to attempt the installation again, or click Cancel to end the

Device Manager agent installation.

(UNIX)

The Device Manager agent installation has been suspended due to requests received from a management server.

Please wait a moment and enter (Y)es to attempt the installation again or enter (N)o to end the Device Manager agent installation.


The Device Manager agent installation has been suspended due to the execution of the one of the following commands:

(hbsasrv, hdvmagt_account, hdvmagt_schedule, hdvmagt_setting,

TIC, hldutil).


Retry to attempt the installation again, or click Cancel to end the

Device Manager agent installation.

(UNIX)

The Device Manager agent installation has been suspended due to the execution of the one of the following commands:


TIC, hldutil).


You have specified "

Program

Files

" folder to install Device

Manager agent when you try to install it to the IA64 platform.

Please install it under

"

Program File (x86)

" folder as far as possible.


The installation was canceled because the Device Manager agent was being accessed from outside.

Wait a while, and then retry the installation. If you want to immediately stop the Device

Manager agent, see the explanation of the hbsasrv command in the Device

Manager agent manual.

The installation was canceled because the Device Manager agent command is executing.



1-169



The Device Manager agent installation has been suspended because the

HiScan command is executing.

Please wait a moment and click Retry to attempt the installation again, or click Cancel to end the Device

Manager agent installation.

(UNIX)

The Device Manager agent installation has been suspended because the

HiScan command is executing.



The Device Manager agent uninstallation has been suspended due to requests received from a management server.


Retry to attempt the uninstallation again, or click Cancel to end the

Device Manager agent uninstallation.

(UNIX)

The Device Manager agent uninstallation has been suspended due to requests received from a management server.


The installation was canceled because the HiScan command is executing.

The uninstallation was canceled because the Device

Manager agent was being accessed from outside.

Wait a while, and then retry the uninstallation. If you want to immediately stop the

Device Manager agent, see the explanation of the hbsasrv command in the Device






The Device Manager agent uninstallation has been suspended because one of the following commands is executing:


TIC, hldutil)




(UNIX)

The Device Manager agent uninstallation has been suspended because one of the following commands is executing:


TIC, hldutil)



The Device Manager agent uninstallation has been suspended because the HiScan command is executing.




(UNIX)

The Device Manager agent uninstallation has been suspended because the HiScan command is executing.


The uninstallation was canceled because the Device

Manager agent command is executing.

Wait a while, then retry the uninstallation.

The uninstallation was canceled because the HiScan command is executing.

Wait a while, and then retry the uninstallation.



1-171

Error Code

KAIC25120-W

KAIC25121-W

KAIC25122-W

Description

User account authentication has failed. Revise the user account information.

The specified user account does not have Administrators permissions.

Revise the user account information.

The specified user account does not have the User Rights Assignment setting "Log on as a service". Make sure the user account has this setting.


Possible causes are as follows:



The specified user account

(user ID) does not exist.



The password for the user account was specified incorrectly.

Check the following points, and then click the [Next] button in the Setting Up the

Agent Service Account window:



Make sure that the specified user account exists.



Make sure that the password for the user account is specified correctly.

The specified user account does not have Administrators permissions.

Make sure that the user performing the installation has Administrators permissions, and then click the [Next] button in the

Setting Up the Agent Service

Account window.

The User Rights Assignment setting "Log on as a service" has not been specified for the specified user account.

Make sure that the User

Rights Assignment setting

"Log on as a service" has been specified for the user performing the installation, and then again click the

[Next] button in the Setting

Up the Agent Service Account window.



Error Code

KAIC25123-W

KAIC25156-E

KAIC25157-E

KAIC25163-E

KAIC25172-E

Description

An error occurred during setup of the agent service account.


An unexpected error occurred during user account authentication.

In the Setting Up the Agent

Service Account window, click the [Next] button again.

If you cannot resolve the problem, do not set up the agent service account (select

[NO] in the Setting Up the

Agent Service Account window), and then click the

[Next] button in that window.

After the installation, open the Services window from

[Administrative Tools], and then change the account for

[HBsA Service].

Install Device Manager agent to execute the setup.exe.

Installation FAILED. Please execute setup.exe to install Device Manager agent.

There is not enough free disk space for installation. Make sure that there is enough free space on the system drive and installation drive.

Installation will now stop.

A newer version of Device Manager agent is already installed on this system. You cannot downgrade

Device Manager agent.

Installation or uninstallation was stopped because an error occurred in the JVM.

Make sure that there is enough free space, and then try installing again.


A prerequisite patch might not have been applied.

Alternatively, if you are using

Unix, the Java information in the properties file used by the

Device Manager agent might not be valid.



Make sure that all prerequisite patches have been applied.For details on the prerequisite patches, see the Device Manager agent manual.



If you are using Unix, make sure the Java information specified in the properties file used by the

Device Manager agent is valid.

If the Java information is invalid, specify the correct

Java information in the properties file, and then reinstall the Device Manager agent.For details on the properties file, see the Device




1-173

1-174

Error Code

KAIC25173-E

KAIC25174-E

KAIC25176-E

KAIC25177-E

KAIC25178-E

KAIC25179-E

KAIC25180-E

KAIC25181-E

KAIC25183-E


Program aborted. Wait a while, and restart this procedure.

This environment is a non-global zone. Installation in a non-global zone is not supported.

An unexpected error occurred during setup processing of the Device

Manager agent.

The installation or uninstallation was executed while the Device Manager agent was running.

Wait a while, and then reexecute.

Please execute the installation in a global zone.

An illegal option is specified.

{specified option}

The mistake is found in the number of arguments. {specified number}

The installation path of the Device

Manager agent cannot be acquired.

It failed in the installation of add-on module. {add-on module name}

It failed in the installation of

Protection Manager.

The user is not the root user.

The setup program could not be executed.

Collect maintenance information and contact the

Support Center.

An invalid option is specified in the installation command or uninstallation command.

Check the syntax, specify the option correctly, and then execute the installation command or uninstallation command again.

The number of arguments in the installation command or uninstallation command is invalid.

Check the syntax, specify the arguments correctly, and then execute the installation command or uninstallation command again.

An attempt to acquire the installation path of the Device

Manager agent has failed.


Support Center.

An unexpected error occurred during installation of the addon module.


Support Center.

An attempt to copy the

Protection Manager files has failed.

Execute hptmguiinst.exe or hptmguiinst.sh, and then take action based on the output error message.

Perform the installation as the root user.



Error Code

KAIC25184-E

KAIC25185-E

KAIC25186-E

KAIC25188-E

Description

A file required for installation of the

Device Manager agent is missing.

No usable JDK or JRE exists. Install a

JDK or JRE, and then retry the operation.

Your user group permissions are not

Administrators permissions.

A fatal error occurred during the installation of the Device Manager agent. Installation will now stop.


A file required for the installation is missing.

Make sure that all files required for the installation exist.

No prerequisite Java version is installed in the system.

Install a prerequisite Java version, and then retry the operation.

Perform installation as a user who has Administrators permissions.




Installation files of the

Device Manager agent could not be copied to a working directory.





Installation files of the

Device Manager agent could not be deleted from a working directory

Collect maintenance information, and then contact the Support

Center.



1-175

Error Code

KAIC25189-E

Description

Installation of the Device Manager agent has FAILED.


Installation of the Device

Manager agent has failed.

Possible causes include the following:





Installation information of a past Device Manager agent or of a past Dynamic

Link Manager still remains.

There is not enough space at the specified installation destination.

Check the following and, if necessary, carry out the recommended action. Then try to install the Device

Manager agent again. If you cannot resolve the problem, collect maintenance information, and then contact the Support Center.



HBase Agent is displayed twice in the Add or

Remove Programs window on a computer where the

Device Manager agent or

Dynamic Link Manager is installed. Alternatively,

HBase Agent is displayed in the Add or Remove

Programs window on a computer where both the

Device Manager agent and

Dynamic Link Manager have been uninstalled. In either of the above cases, execute the hbsa_util command, and then delete the Device Manager agent registry and files. For details on this command, see the Device Manager agent manual.



Make sure that there is enough free space on the disk where the Device

Manager agent is to be installed.



Error Code

KAIC25190-E

KAIC25193-E

KAIC25194-E

KAIC25197-E

KAIC25198-E


Installation of the Device Manager agent was completed, but the setup of the Device Manager agent or a related program has FAILED.

If you want to use the related program for which setup did not finish, reinstall the Device Manager agent.

If you will not use the related program for which setup did not finish, no additional action is required.

The execute permission for the installation files could not be changed.

An attempt to open the

'HDVMAgent_conf file name' file has

FAILED.

The format of line %d in the

'HDVMAgent_conf file name' is invalid.

A property in the 'HDVMAgent_conf

file name' has been incorrectly specified(line %d).




Setup of the Device

Manager agent failed.









Setup of the Protection

Manager linkage function failed.

Setup of the Dynamic Link

Manager linkage function failed.

Setup of the account information for the Device

Manager agent service

(HBsA Service) failed.

Installation of the Global

Link Manager agent failed.

If you want to use the related program for which setup did not finish, reinstall the Device

Manager agent.

If you will not use the related program for which setup did not finish, no additional action is required.

The execute permission for the installation files could not be changed.

Put the installation files into a directory that can be written to.

An attempt to open the

'HDVMAgent_conf file name' file has failed.

The HDVMAgent.conf file was not found in the directory that contains the installer. Make sure that the file is there, and then try to install the Device

Manager Agent again.

The format of the

HDVMAgent.conf file is invalid.

The HDVMAgent.conf file might be corrupted. Check the file, and then try to install the Device Manager Agent again.

A property in the

HDVMAgent.conf file has been incorrectly specified(line %d).

The HDVMAgent.conf file might be corrupted. Check the file, and then try to install the Device Manager Agent again.



1-177

1-178

Error Code

KAIC25208-E

KAIC28201-W

KAIC28202-W

KAIC28203-W

KAIC28204-W


Setup of the Device Manager agent has FAILED.

The IP address could not be resolved from the specified hostname.

Access to the server has failed. (detail

= "Verify network connectivity and that the Device Manager server is running")

The setup program could not be executed.

Follow the instructions in the following messages:

KAIC25029-I, KAIC25033-I.







Make sure that the entered value is correct.

Make sure that the hostname is defined in the hosts file.

To specify an IPv6 address, server.agent.JRE.location must be specified. Make sure that the specified value is correct.












Check the firewall settings on the machines on both the host side and the server side.

If a firewall is configured between the host and the server, make sure that the settings are correct.

If you want to install the

Device Manager server later, click No in the confirmation window, and then continue setup.



Access to the server has failed. (detail

= "Unauthorized user ID or password is invalid")

Access to the server has failed.

(details = "A normal response could not be recieved from the Device

Manager server.")









Check the status of the

Device Manager server. If the server is in the process of starting, wait a while, and then retry the operation.

If the problem cannot be solved, collect maintenance information and contact the

Support Center.



Error Code Description


RAID Manager is not installed on the selected drive. (specified drive:

\HORCM)

(UNIX)

RAID Manager is not installed in the selected directory.


If you want to install RAID

Manager later, click [NO] in the confirmation window, and then continue setup.

(Windows)

Make sure that RAID

Manager is installed on the specified drive.

(UNIX)

Make sure that RAID

Manager is installed in the specified directory.



1-179

Error Code

KAIC28305-E

KAIC28306-E

KAIC28307-E

KAIC28308-E

KAIC28309-E

KAIC28310-E

KAIC28311-E

KAIC28312-E

KAIC28313-E

KAIC28314-E

Description

The specified IP address or hostname is invalid.

The specified port number is invalid.

The specified User ID is invalid.

The specified password is invalid.

The IP address or hostname contains invalid characters.

Check the value and enter again.

Refer to the Device Manager agent manual for characters you can use.

The user ID contains invalid characters.



The password contains invalid characters.



An unexpected error occurred when the Device Manager server information was being specified.

The server information cannot be specified.

An I/O error occurred when the

Device Manager server information was being specified.

The server information cannot be specified.

An unexpected error occurred when the execution period of the HiScan command was being specified.

The execution period of the HiScan command cannot be specified.


Enter a valid value.


Support Center.





Make sure that the server.properties file exists, and you have write permissions for the file.

Make sure that there is enough free space on the disk.


Support Center.



Error Code

KAIC28315-E

KAIC28316-E

KAIC28317-E

KAIC28318-E

KAIC28319-E

KAIC28353-E

KAIC28615-W

Description

An I/O error occurred when the execution period of the HiScan command was being specified.

The execution period of the HiScan command cannot be specified.

An unexpected error occurred when

RAID Manager settings were being specified.

These RAID Manager settings cannot be specified.

An I/O error occurred when RAID

Manager settings were being specified.

These RAID Manager settings cannot be specified.





Make sure that the server.properties file exists, and that you have write permissions for the file.



Support Center.

A fatal error occurred during the setup processing of the Device

Manager agent.

Setup processing has stopped.

A site-local address or link-local address is specified for the IP address. To use IPv6 addresses, you must specify a global address.

Setup processing has stopped because the Add-On module is currently running.

The host does not recognize the defined command device.








Make sure that the directories shown below exist, and you have write permissions for the files.

Windows:

Device-Manager-agentinstallation-

directory\mod\hdvm\config

UNIX platforms except

AIX:

/opt/HDVM/HBaseAgent/m od/hdvm/config

AIX:

/usr/HDVM/HBaseAgent/m od/hdvm/config


Make sure that the crontab or at command can be used.


Support Center.

Please specify a global address.

Wait a while, then retry the operation.





Make sure that the description of the command device is correct.

Make sure that the connection status between the host and the storage subsystem is correct.



1-181

1-182

Error Code

KAIC28616-W

KAIC28804-E

KAIC28805-E

KAIC28807-E

KAIC28809-E

KAIC28810-E

Description

No command device recognized by the host is defined.

No command device is defined in the configuration file.

An I/O error occurred while reading the configuration file.

The processing was interrupted because no handle could be acquired from RMLIB.

The file perf_cmddev.properties was not found.

An I/O error occurred. <filename>

(Error details: errno = error-code, msg = error-message)






Add the specified command device to the properties file.

Update the file perf_cmddev.properties by using the following command: perf_findcmdev write

Define the command devices by using the perf_findcmddev command.

An I/O error occurred while reading the perf_cmddev.properties file.

Make sure of the following:





The perf_cmddev.properties file exists.

The perf_cmddev.properties file is readable.

If the perf_cmddev.properties file does not exist, create the file by using the perf_findcmddev command.

The RMILIB API became unusable during request processing.

If the problem occurs frequently, collect maintenance information and contact the support center.

Make sure that the file perf_cmddev.properties exists and is valid.







Make sure that the file perf_cmddev.properties exists and is not writeprotected.


Make sure that the directory to which the file will be written exists.



Table 1-15 KAIE00000-KAIE69999: Agent Errors (used by all Hitachi

Storage Command Suite products)

Error Code

KAIE10401-E

KAIE10403-E

KAIE10404-E

KAIE10502-E

KAIE10602-E

KAIE10606-E

KAIE10610-E

KAIE16002-I

KAIE16605-I

KAIE16606-I

Error Message

A serious error was detected during one of the following processes:



Installation or uninstallation



Addon-module loading



Request reception

There might be a memory shortage or an internal error.

An error occurred when loading a module. There might be a memory shortage or an internal error.

An I/O error occurred.

An attempt to access the following files has failed:





Device Manager agentinstallation-

directory/agent/mod/*


directory/agent/mod/*/var

The service might not have permission to access these files or directories.

The environment is invalid. An attempt to read the product information file (Device Manager

agent-installation-

directory/etc/amc_iid) has failed.

The installation might not have finished correctly.

The environment is invalid.


Make sure that there are no memory shortages, and then restart the service. If this does not resolve the problem, collect maintenance information and contact the Support Center.

Make sure that the user who is executing the service has permission to access these files or directories. If the user does not have permission, grant permission, or change to a user who has permission.

Re-install. If this does not resolve the problem collect maintenance information and contact the

Support Center.

An I/O error occurred. An attempt to generate the product information file

(Device Manager agent-installation-

directory/etc/amc_iid) has failed.

The installation might not have finished correctly.

An attempt to uninstall failed. The module has been used.

The detail of the error information is output.

There are no registered add-on modules or there are no usable registered add-on modules.

The specified add-on module is not registered, or it is registered but is currently disabled.

For appropriate action, see the past operating log message containing details about the problem.

Re-install. If this does not resolve the problem collect maintenance information and contact the

Support Center.

Re-uninstall after a while.

For appropriate action, see the content of exception information.


When using a specified add-on module, make sure that the specified add-on module is installed and is supported on this platform.



1-183

1-184

Error Code

KAIE20001-E

KAIE20002-E

KAIE20101-E

KAIE20102-E

KAIE20303-E

KAIE20402-E

KAIE20403-E

KAIE20601-E

KAIE20701-E

Error Message Recommended Action

A serious error was detected during one of the following processes:





Addon-module loading

Request reception


A serious error was detected during service execution. There might be a memory shortage or an internal error.

An unexpected error occurred during processing of the request. There might be a memory shortage or an internal error.



A serious error was detected during service execution. There might be a network error or a memory shortage.


Make sure that there are no network errors or memory shortages, and then restart the service. If this does not resolve the problem, collect maintenance information and contact the

Support Center.

An unexpected error occurred during

HTTP connection processing. There might be a network error or a memory shortage.

An I/O error occurred while communicating with the remote host. The remote host might have severed the connection, or there might be a network error or memory shortage.

An unexpected error occurred during processing of the service request.


An error occurred while creating the log output destination directory. The service might not have write permissions for the following directory:

Device Manager agent-installation-

directory/agent

If it was not a normal disconnection by the remote host, make sure that there are no network errors or memory shortages, and then restart the service. If this does not resolve the problem, collect maintenance information and contact the Support Center.


Make sure that the user who is executing the service has permission to access these files or directories. If the user does not have permission, grant permission, or change to a user who has permission.



Error Code

KAIE20702-E

KAIE20703-E

KAIE20704-E

KAIE20705-E

KAIE20706-E

Error Message

An error occurred while creating the log output destination directory. A file which has the same name


directory/agent/logs) already exists.

The log output destination directory


directory/agent/logs) is read-only.

An attempt to access the log property file (Device Manager agent-

installation-

directory/agent/config/logger.propert

ies) has failed. Possible causes are:





The file does not exist.

The user has the file open.





The user lacks access permissions.

The settings are invalid.


Delete the file which has the same name as the directory.

Make the log output destination directory writable.









Make sure that the logger.properties file exists.

If the logger.properties file is open, close it.

Grant access permissions for the logger.properties file, or change to a user who has access permissions and restart the service.

Check the settings of the logger.properties file. If they are invalid, correct them.

Delete the directory which has the same name as the log output file.

The log output file cannot be created. A directory which has the same name as a log output file

(below) exists in the log output destination directory.




directory/agent/logs/trace.log




directory/agent/logs/access.log






directory/agent/logs/error.log


directory/agent/logs/service.log

One of the following log output files is not writable because the user who is executing the service does not have write permissions for that file:




directory/agent/logs/trace.log




directory/agent/logs/access.log






directory/agent/logs/error.log


directory/agent/logs/service.log

Grant write permissions for the log output file, or change to a user who has write permissions and restart the service.



1-185

1-186

Error Code

KAIE20707-E

KAIE20901-E

KAIE20902-E

KAIE20903-E

KAIE20904-E

KAIE21701-W

KAIE21702-W

KAIE21703-W

Error Message

There is an error in the settings of the property file

( server.properties

).

An unrecoverable error occurred in the service execution process. There might be a memory shortage or an internal error.

A network error occurred while waiting for a connection. There might be a network error or a memory shortage.

An unexpected error occurred in the service execution process. There might be a memory shortage or an internal error.

An error occurred during shutdown of the service execution process.


Check each value of the server.properties

property and correct them if necessary.



If the following properties are specified in the properties file, revise the specification: server.http.socket.agentAddr

ess

 server.http.socket.bindAddre

ss


Make sure that there are no network errors or memory shortages. If the problem occurs frequently, collect maintenance information and contact the

Support Center.

Make sure that there are no network errors or memory shortages, and then restart the service. If this does not resolve the problem, collect maintenance information and contact the

Support Center.

Make sure that there are no network errors or memory shortages. If this does not resolve the problem, collect maintenance information and contact the

Support Center.

Correct the value for logger.MaxBackupIndex, then restart the service.

The value for the property logger.MaxBackupIndex in logger.properties is outside the range from 1 to 20, or it is not a number.

The value for the property logger.MaxFileSize in logger.properties is outside the range from 512 KB to 32 MB, or it is not a number.

There is an error in the settings of the property file

( server.properties

).

Correct the value for logger.MaxFileSize, then restart the service.

Check each value of the server.properties

property and correct them if necessary.



Error Code

KAIE30101-E

KAIE30201-E

KAIE30504-E

KAIE30505-E

KAIE30506-E

KAIE30507-E

Error Message





An unexpected error occurred during execution of the service control process stop command. There might be a memory shortage or an internal error.

The service execution process could not start because the environment is invalid.

The service execution process detected an unexpected error. There might be a memory shortage or an internal error.

A communication error occurred during the execution of "hbsasrv stop". Possible causes are:





The service control process cannot receive commands because of a problem such as a system resource shortage.

The service control process is not working correctly.

Make sure that there are no memory shortages, and then retry a forced termination of the service.

If this does not resolve the problem, collect maintenance information and contact the

Support Center.

For details on the appropriate action, see the preceding message that gives details about the problem.


Re-execute "hbsasrv stop".

If the above actions do not resolve the problem, collect maintenance information and contact the

Support Center.



1-187

1-188

Error Code

KAIE60607-E

KAIE62001-I

KAIE62601-E

KAIE62602-E

KAIE62604-E

KAIE62605-E

Error Message

Processing has stopped because the current user is different from the previous installer.

HBsA Service is already running.

Permission of HBsA Service was denied.

The directory structure is invalid.

Unable to stop HBsA Service because

Add-On module is currently running.

The connection error of HBsA Service has occurred.


Processing can no longer continue because the current user ID is different than the user ID who last installed Dynamic Link Manager or

Device Manage agent.

Follow steps 1-3 of the procedure written below. If this problem persists, contact the Support

Center.

1. If Dynamic Link Manager 5.8.0-

00 to earlier than 5.9.4-00 has been installed:Retry as the same user ID who previously installed

Dynamic Link Manager.

2. If Device Manager agent 5.0.0-

00 to earlier than 5.9.0-00 has been installed:Retry as the same user ID who previously installed

Device Manager agent.

3. In situations other than the above:First retry installation as the user ID who previously installed Dynamic Link Manager

5.8.0-00 to earlier than 5.9.4-00 and Device Manager agent

5.0.0-00 to earlier than 5.9.0-

00.

Only one instance of HBsA Service can run on a system at any given time.

A user without Administrator permissions executed the command. Execute this command as a user with Administrator permissions.

Device Manager agent was not installed correctly. Make sure that installation of Device Manager agent was performed correctly.

Wait a while, and then retry the operation. For details on how to stop the service, see the explanation of the hbsasrv command.

Make sure that the TCP/IP environment on the host is normal.

To do this, use the standard OS commands for network monitoring

(such as netstat or ping.).

If there is no problem, restart the system and then re-install the program. If the problem persists, collect the maintenance information and contact the Support Center.



Error Code

KAIE62606-E

KAIE62607-E

KAIE62608-E

KAIE62638-E

KAIE62639-E

KAIE65601-E

Error Message

An error occurred while starting

HBsA Service.

The HBsA service could not start normally.

The Java path is invalid. [{path}]


Re-install the program. If the problem persists, collect the maintenance information and contact the Support Center.

Make sure that the prerequisite patches have been applied, and then re-install the program.

Revise the value specified for server.agent.JRE.location in server.properties, and then retry the operation.

Correct the value for server.agent.maxMemorySize, and then restart the HBsA service.

The value specified for server.agent.maxMemorySize in the server.properties file is not numeric.

The value specified for server.agent.maxMemorySize in the server.properties file is outside the valid range.

The command was executed by a user other than the administrator.





1-189

Device Manager Agent's Provisioning Manager Messages

This section describes the messages output by the Provisioning Manager support functionality of the Device Manager agent and the actions to take in response to these messages.

Table 1-16 lists the error messages related to the Provisioning Manager

support functionality of the Device manager agent, and provides recommended actions sfor resolving the error conditions. The error messages are listed in numerical order by error code. For details on the Provisioning

Manager messages (error codes starting with KARF) that are not listed in Table

1-16, see the Provisioning Manager message manual.

Table 1-16 Device Manager Agent's Provisioning Manager Messages

Error Code

KARF62001-E

KARF62002-E

KARF62003-E

KARF62004-E

Error Message

The specified volume manager type is not supported.

The specified device file does not exist.

The specified device file is not mounted.

A file or directory (folder) exists in the specified mount point directory.

Cause and Action

Cause:

The Agent information recognized by the Provisioning Manager server has not been updated.

Action:

Refresh the host information, and then retry the operation.

Cause:

The host information recognized by the

Provisioning Manager server has not been updated.

Action:


Cause:



Action:


Cause:

The Agent information recognized by the Provisioning Manager server has not been updated, or the requested operation is invalid in the host's system configuration.

Action:

Refresh the host information, and then retry the operation. Alternatively, depending on the contents of the error message, revise the host status, remove the cause of the error, and then retry the operation.



Error Code

KARF62007-E

KARF62008-E

KARF62010-E

KARF62011-E

KARF62012-E

Error Message

The specified device file is already being used.

A mount point exists in the specified mount point.

The specified extension size is invalid.

The specified logical volume does not exist.

The specified mount point is already in use.


Cause:



Action:


Cause:


Action:

Depending on the contents of the error message, revise the host status, remove the cause of the error, and then retry the operation.

Cause:


Provisioning Manager server has not been updated, or processing might have been performed for the same resource.

Action:


Cause:



Action:


Cause:


Action:




1-191

1-192

Error Code

KARF62014-E

KARF62015-E

KARF62018-E

KARF62023-E

KARF62024-E

Error Message

The specified mount point does not exist.

The specified mount point is a file.

A mount point cannot be created.

The logical volume name is invalid.

A process using the specified file system exists.


Cause:



Action:


Cause:

The requested operation is invalid in the host's system configuration.

Action:


Cause:

The directory specified as the mount point might be in one of the following states:

A file that has the same name as the specified directory exists.

The specified directory already exists and a file exists under that directory.

The specified directory already exists and that directory is mounted.

Action:

Update the host information. Search for and delete the device files that were generated while the file system was being added, remove the cause of the error, and then retry the operation to add the file system.

Cause:

The request was made with an invalid value.

Action:

Acquire the error information for

Provisioning Manager and Device

Manager, and then contact the Support

Center.

Cause:


Action:




Error Code

KARF62025-E

KARF62026-E

KARF62027-E

KARF62028-E

KARF62029-E

KARF63002-E

Error Message

2 or more logical volumes are on the specified disk.

A file system that has multiple device files mounted cannot be modified or deleted.

There is a snapshot volume for the specified logical volume.

The specified logical volume is a snapshot.

A file system that has been mounted on multiple mount points cannot be modified or deleted.



Cause:



Action:


Cause:

Multiple device files have been mounted on the specified mount point.

Action:

Check the host status, revise the mount setting to the specified mount point, and then retry the operation.

Cause:


Provisioning Manager server has not been updated. The operation cannot be executed because there is a snapshot volume for the specified logical volume.

Action:

Refresh the host information.

Cause:


Provisioning Manager server has not been updated. The operation cannot be executed because the specified logical volume is a snapshot.

Action:


Cause:

There are mount points, other than the specified mount point, that the same device file has been mounted on.

Action:

Check the host status, revise the mount setting to the specified mount point, and then retry the operation.

Cause:



Action:




1-193

1-194

Error Code

KARF63003-E

KARF64001-E

KARF64003-E

KARF64004-E

KARF64005-I

KARF64006-E

Error Message

The specified physical volume does not exist.

A logical volume already exists on the specified physical volume.

Logical volumes or physical volumes exist in the specified volume group.

A mount point exists on the specified drive.

The logical volume name will be handled as '*'.

The physical volume name is invalid.


Cause:



Action:


Cause:



Action:


Cause:


Provisioning Manager server has not been updated, or there is an unnecessary logical volume or physical volume in the specified volume group.

Action:

No action is required because recovery is performed internally in Provisioning

Manager.

Cause:



Action:


Cause:

-

Action:


Cause:


Action:




Center.



Error Code

KARF64007-E

KARF64008-E

KARF64009-E

KARF64010-E

KARF64011-E

KARF64012-E

Error Message

The specified logical volume already exists.


The specified logical volume size is invalid.

The specified physical volume is already in use.


The specified volume group already exists.


Cause:



Action:


Manager.

Cause:



Action:


Cause:



Action:


Cause:


Provisioning Manager server has not been updated. Or the requested operation is invalid to a host's system configuration.

Action:


Cause:



Action:


Cause:


Provisioning Manager server has not been updated, or the requested operation is invalid in the host's system configuration.

Action:


Manager.



1-195

1-196

Error Code

KARF64013-E

KARF64014-E

KARF64015-E

KARF64017-W

KARF64018-W

KARF64019-W

Error Message

The specified volume group does not exist.

A logical volume cannot be created on the specified device file.

The information relating to the volume group cannot be acquired.

Importing to the specified disk was unnecessary.

The specified disk was already

Basic.

The specified disk was already

Dynamic.


Cause:



Action:


Cause:


Provisioning Manager server has not been updated. Or the device may not be correctly recognized on the host.

Action:


Cause:

The host's application (VxVM) settings are incorrect.

Action:

Revise the host's application (VxVM) settings, remove the cause of the error, and then retry the operation.

Cause:

The disk was already recognized by the host.

Action:

There is no problem in operation, so processing will continue. No action is required.

Cause:

The disk was already a Basic disk.

Action:


Cause:

The disk was already a Dynamic disk.

Action:




Error Code

KARF64020-E

KARF64021-E

KARF64022-E

KARF64023-E

KARF64024-W

KARF64025-E

Error Message

The logical volume name is invalid.

The specified logical volume is still being used.

You cannot use the

DeleteVolumeGroup API to delete a volume group that contains 2 or more physical volumes.

You cannot use the

DeletePhysicalVolume API to delete a physical volume from a volume group that contains only 1 physical volume.

The logical volume Logical

volume name journal log cannot be deleted because it is being used.

The specified disk has an error status.


Cause:


Action:




Center.

Cause:



Action:


Cause:


Provisioning Manager server has not been updated. Or processing may have been performed to the same resource.

Action:


Cause:


Provisioning Manager server has not been updated. Or processing may have been performed to the same resource.

Action:


Cause:

The logical volume was not deleted because it is being used as a journal log.

Action:


Cause:

A setup of a host's application (VxVM or

Dynamic Link Manager) is inaccurate.

Or the requested operation is invalid to a host's system configuration.

Action:

Depending on the contents of the error message, revise the host status and application (VxVM or Dynamic Link

Manager) settings, remove the cause of the error, and then retry the operation.



1-197

1-198

Error Code

KARF64026-E

KARF64027-E

KARF64028-E

KARF64029-E

KARF64031-E

KARF64032-E

KARF64033-E

Error Message

2 or more logical volumes are on the specified disk.

The specified logical volume has a snapshot.

The specified logical volume is a snapshot.

A partition cannot be specified for the device file.

One or more physical volumes other than an md device exist in the specified volume group.

The md device has been created with multiple device files.

The specified HDLM path is not in the Online status.


Cause:



Action:


Cause:


Provisioning Manager server has not been updated. The operation cannot be executed because there is a snapshot volume for the specified logical volume.

Action:


Cause:


Provisioning Manager server has not been updated. The operation cannot be executed because the specified logical volume is a snapshot.

Action:


Cause:


Action:


Cause:



Action:


Cause:



Action:


Cause:

An error might have occurred in the

HDLM path.

Action:

See the Dynamic Link Manager manual, remove the cause of the error, and then retry the operation.



Error Code

KARF64034-E

KARF64035-E

KARF64036-E

KARF64037-E

Error Message

An attempt to create a directory for the volume group has failed. (directory =

directory)

A group file cannot be created because the maximum value of the minor number exceeds the system limit.

The specified logical volume is being used by the cluster software.

The specified logical volume has been marked as part of a high-availability cluster.


Cause:


Provisioning Manager server has not been updated, or the requested operation is invalid in the host's system configuration.

Action:


Cause:

The maximum value of the minor number exceeds the system limit (FF).

Action:

Delete any unnecessary group files, and then retry the operation.

Cause:

Provisioning Manager cannot be used to operate a logical volume that is being used by the cluster software.

Action:

Manually perform the following procedure, and then retry the operation:

Edit the cluster configuration file.

Execute cmapplyconf

.

Cause:

Provisioning Manager cannot be used to operate a logical volume that is being used by the cluster software.

Action:

Manually perform the following procedure, and then retry the operation:

Execute the vgchange -a n

command to deactivate the volume group.

Execute the vgchange -c n

command to remove the high-availability cluster mark.

Execute the vgchange -a y

command to activate the volume group.




1-199

1-200

Error Code

KARF64038-E

KARF64039-E

KARF64040-E

KARF65001-E

KARF65002-E

Error Message

The cluster configuration of the host is invalid.

An attempt to delete the directory for the created volume group has failed.

(directory name = directory)

A partitioned disk cannot be used.

The specified raw device does not exist.

An HDLM device corresponding to the specified device does not exist.


Cause:

There is an inconsistency between the host cluster configuration and cluster configuration file.

Action:

Refer to the Serviceguard manual to check the contents of the cluster configuration file. If necessary, check the cluster system status, remove the inconsistency between the host cluster configuration and cluster configuration file, and then retry the operation.

Cause:

Rollback processing has failed.

Action:

Delete the directory that was output in the message.

Cause:

The specified disk includes one or more partitions.

Action:

If the partitions are not in use, unpartition the disk, and then retry the operation.

Cause:

The specified raw device is not correctly recognized as a device file on the host.

Action:

Make the specified raw device recognizable as a device file, and then resume processing.

Cause:

An attempt to create an HDLM device might have failed. Alternatively, an attempt to either recognize the LU specified by the request or create a device file might have failed.

Action:

Refresh the host information to check whether the specified LU appears. If it does not appear, make the host recognize the LU, create an HDLM device, and then retry the operation.

For details on how to make a host recognize an HDLM device, see the

Dynamic Link Manager manual.



Error Code

KARF65003-E

KARF65011-W

KARF65012-I

KARF65013-E

KARF65014-E

KARF66001-E

KARF66002-E

Error Message

The HDLM path is invalid.


The cfgmgr command will be executed number of command

execution times.

The specified raw device still exists.

An unnecessary device file exists.

VolumeManagerAdmin execution error.

FileSystemAdmin execution error.


Cause:

The host's application (Dynamic Link

Manager) settings are incorrect, or the requested operation is invalid in the host's system configuration.

Action:

Depending on the contents of the error message, revise the host status and application (Dynamic Link Manager) settings, remove the cause of the error, and then retry the operation.

Cause:



Action:


Cause:

-

Action:


Cause:

The specified raw device was not correctly deleted from the host.

Action:

Delete the specified raw device from the host, and then resume processing.

Cause:

The specified raw device was not correctly deleted from the host.

Action:

Delete the specified raw device from the host, and then resume processing.

Cause:

An unexpected internal error occurred.

Action:




Center.

Cause:


Action:




Center.



1-201

1-202

Error Code

KARF66003-E

KARF66004-E

KARF66005-E

KARF66006-E

KARF66007-E

KARF66008-E

KARF66009-E

Error Message

RawDeviceAdmin execution error.

The specified volume manager type is not supported.

The specified file system type is not supported.


The raw device cannot be deleted because there is a partition in the raw device.

The specified mount point

(mount-point) is invalid.

An md device already exists on the specified device file.


Cause:


Action:




Center.

Cause:


Action:


Cause:


Action:


Cause:

The specified raw device is not correctly recognized as a device file on the host.

Action:

Make the specified raw device recognizable as a device file, and then resume processing.

Cause:

Partitions exist on the specified raw device.

Action:

Delete all partitions in the raw device if they are not being used, and then retry the operation.

Cause:

The mount point included at least one invalid character.

Action:

You cannot use Provisioning Manager to add, expand or delete the specified file system. Manually add, expand or delete it, and then refresh the host information.

Cause:

An unsupported device file was specified.

Action:

Delete the md device, and then retry the operation.



Error Code

KARF66010-E

KARF66011-E

KARF66012-E

KARF67001-E

KARF67002-E

KARF70001-E

Error Message Cause and Action

The specified logical volume cannot be deleted because its path length exceeds 32 characters.

An attempt to create a device file for the specified volume group has failed. (volume group = Volume group name)

An attempt to create a device file for the specified logical volume has failed. (volume group = Volume group name, logical volume = Logical

volume name)

The md device cannot be created because a system limit was exceeded.

Cause:

The path length of the specified logical volume exceeds 32 characters.

Action:

The specified logical volume cannot be deleted.

Cause:

A device file already exists for the specified volume group, or a file with the same name already exists.

Action:

Specify a different volume group name, and then retry the operation.

Cause:

A device file already exists for the specified logical volume, or a file with the same name already exists.

Action:

After manually deleting the created volume group, specify a different logical volume name, and then retry the operation.

Cause:

The number of md devices exceeded a system limit.

Action:

Delete an unnecessary md device, and then retry the operation.


Cause:



Action:

Refresh the host information, and then retry the operation. processing Cause:


Action:




Center.

Exception occurred = class

name

Cause:


Action:




Center.



1-203

1-204

Error Code

KARF70002-E

KARF70003-I

Error Message

The specified parameter is invalid.

Execution command =

command, startTime =

command start time.

KARF70004-E Command execution error =

command

KARF70005-E Program Product is not installed.

KARF70006-E Program Product is not supported.

KARF70007-W An attempt to delete the file has failed. (file name = file

name)

KARF70008-E The specified parameter is invalid.


Cause:


Action:




Center.

Cause:

-

Action:


Cause:

A command execution error occurred.

Action:

Depending on the contents of the error message, revise the host status and application settings, remove the cause of the error, and then retry the operation.

Cause:


Action:


Cause:


Action:


Cause:

An attempt to delete the file indicated in this message has failed.

Action:


Cause:

The hldutil command returned an unexpected execution result.

Action:




Center.



Error Code

KARF70009-E

KARF70010-W

KARF70012-I

KARF70013-I

KARF70014-E

KARF70015-E

KARF70016-E

Error Message

The specified parameter length is invalid.

Command execution error =

Command execution result

Waiting wait time seconds before starting the next command.

Command execution result =

command execution result, endTime = command end

time.

The execution result of the command is invalid.

The specified entry already exists in Definition file.

The specified mount point does not exist in Definition file.


Cause:

The hldutil command returned an unexpected execution result.

Action:




Center.

Cause:

A nonfatal error occurred during command execution.

Action:


Cause:

-

Action:


Cause:

-

Action:


Cause:

The command returned an unexpected execution result.

Action:




Center.

Cause:


Action:


Cause:


Action:




1-205

1-206

Error Code

KARF70017-E

KARF70018-E

KARF70019-E

KARF70020-E

KARF70021-E

KARF70022-W

Error Message Cause and Action

Definition file cannot be backed up.

Definition file cannot be read.

The entry cannot be removed from Definition file.

Definition file cannot be updated.

The system environment is invalid. (value = An unjust

value)

An attempt to set the value for

Key Name has failed. The default value default Value will be used.

Cause:


Action:


Cause:


Action:


Cause:


Action:


Cause:


Action:


Cause:

The host's configuration system or the application (whole) settings are incorrect. Alternatively, the requested operation is invalid in the host's system configuration.

Action:

Depending on the contents of the error message, revise the host status and application settings, remove the cause of the error, and then retry the operation.

Cause:

An invalid value exists in the settings file.

Action:

Revise the settings file.



Error Code

KARF70023-E

KARF70024-E

KARF70025-E

KARF70026-W

KARF70027-W

KARF70028-W

KARF70029-E

Error Message

The specified entry does not exist in Definition file.

An error occurred because an invalid value was detected.

(attribute = method name, value = Invalid value)

The command results do not contain a value that matches

missing Value.

The default value default Value will be used because the value

specified Value is invalid.

The number value value that corresponds to Header Name could not be acquired from the command execution results.

The object object does not exist. new object will now be created.

A directory exists that has the same name as the backup file.

(directory = directory)


Cause:

The system configuration of the host is incorrect, or the requested operation is invalid in the system configuration of the host.

Action:


Cause:


Action:




Center.

Cause:


Action:


Cause:

Processing will continue, ignoring the invalid value that was returned.

Action:


Cause:

Processing will continue, ignoring the unexpected value returned as the command execution result.

Action:


Cause:

A nonfatal error occurred.

Action:


Cause:

Processing could not continue because a directory that has the same name exists.

Action:




1-207

Error Code

KARF70030-I

KARF70031-E

Error Message

The value that corresponds to

Header name is acquired.

(value = value)

Command output message (

message )


Cause:

-

Action:


Cause:

The cause depends on the error that occurred.

Action:

Depending on the contents of the message, revise the host status and application settings, remove the cause of the error, and then retry the operation.



Device Manager Agent's Replication Manager Messages

This section describes the messages output by the Replication Manager support functionality of the Device Manager agent and the actions to take in response to these messages.

Table 1-17 lists the error messages related to the Replication Manager support

functionality of the Device Manager agent, and provides recommended actions for resolving the error conditions. The error messages are listed in numerical order by error code.

Table 1-17 Error Codes KAVN01800-KAVN01813: Device Manager Agent's

Replication Manager Messages

Error Code

KAVN01800-I

KAVN01801-I

KAVN01802-I

KAVN01803-I

KAVN01804-E


The CCI instance has stopped successfully.

Cause:

The CCI instance (HORCM instance) has stopped successfully.

Action:


The CCI instance has started. Cause:


Action:


The CCI instance has already stopped.

The CCI instance has stopped.

An error occurred while acquiring the status of the

CCI instance.

Cause:


Action:


Cause:

The CCI instance (HORCM instance) has stopped.

Action:


Cause:

An attempt to acquire the CCI instance

(HORCM instance) status has failed.

Action:

Check the status of CCI, and then correct the problem. Then, retry the operation.



1-209

1-210

Error Code

KAVN01805-E

KAVN01806-E

KAVN01807-E

KAVN01808-I

KAVN01809-I

KAVN01810-E

KAVN01811-E


A supported version of CCI was not found.

CCI was not found.

An argument other than "stop" has been specified.

Collection of maintenance information from the

Replication Manager agent will now start.

Collection of maintenance information from the

Replication Manager agent has ended.

Cause:

The prerequisite version of CCI for

Replication Manager was not found.

Action:

Install the prerequisite version of CCI for Replication Manager, and then retry the operation.

Cause:

CCI is not installed.

Action:

Install the prerequisite version of CCI for Replication Manager, and then retry the operation.

Cause:

An argument other than the -stop is specified on the command line.

Action:

Check the argument, and then reexecute the command.

Cause:

The collection of maintenance information from the Replication

Manager agent has started.

Action:


Cause:

The collection of maintenance information from the Replication

Manager agent has ended.


An argument is not specified. Cause:

The hrpm_getras command was executed without specifying an argument (the output directory).

Action:

Specify an argument (the output directory), and then execute the hrpm_getras command.

The directory specified as an argument of the

TIC command of the Device

Manager agent cannot be accessed

Cause:

The directory specified as an argument of the hrpm_getras command cannot be accessed.

Action:

Check whether the directory specified as an argument exists and whether access permission is granted for the user, and then retry the operation.



Error Code

KAVN01812-E

KAVN01813-E

Description

An error occurred during collection of maintenance information from the

Replication Manager agent.

The specified parameter value is invalid.


Cause:


TIC

command of the Device Manager agent during the collection of maintenance information from the Replication Manager agent.

Action:

Re-execute the

TIC

command of the

Device Manager agent. If the error occurs again, change the value of the argument, and then re-execute the command. If the problem cannot be corrected, contact the Support Center.

Cause:

Multiple arguments are specified, or the argument is specified incorrectly.

Action:

Specify a single argument, and then reexecute the

TIC

command of the Device

Manager agent. If the error still occurs, change the value of the argument, and then re-execute the command. If the problem cannot be corrected, contact the Support Center.



1-211

Device Manager VDS Provider Messages

When an error occurs, Device Manager VDS Provider produces one or more error messages. An error message consists of a message number, a level code indicating the severity of the error, and the error message text. Message numbers are grouped by error type. If you run Device Manager Agent in an

English environment, some messages are output in English, although they share the same meaning, as well as the same error codes, as the Japanese messages.

Device Manager VDS Provider messages are written to a secondary output device in the following format:

revision-level / timestamp / message-text

revision-level indicates an internal revision number of the program. This information is required when an error is reported to the Hitachi Data Systems

Support Center.

timestamp, although subject to the local time zone, is always in the same format in other respects. In other words, there are no locality-specific format differences in a timestamp.

message-text begins with a message number followed by one of the following message levels indicating the severity:

–

–

I

: non-error information

W

: warning

–

E

: error

Table 1-18 lists the Hitachi Device Manager VDS Provider error messages, and

provides recommended actions for resolving the error conditions. The error messages are listed in numerical order by error code.

Table 1-18 KAIC24000-KAIC24999: Hitachi Device Manager VDS Provider

Errors

Error Code

KAIC24001-E

KAIC24017-E

KAIC24054-E

Description

An attempt to create a thread has failed.

An attempt to allocate a buffer for

CHdvmComm failed due to lack of memory.

The CIM operation failed.

(<detailed-message>)



Please add more memory.

An attempt to communicate with the

Device Manager server has failed. The details portion of this message should indicate the nature of the problem. Revise the Device Manager VDS provider properties.



Error Code

KAIC24063-E

KAIC24065-E

KAIC24123-E

KAIC24124-E

KAIC24125-E

KAIC24126-E

KAIC24132-E

KAIC24133-E

KAIC24140-E

KAIC24141-E

KAIC24142-E

KAIC24805-E

Description

Communication with the Device

Manager server failed.

This application runs on Windows

Server 2003 only. Installation will now stop.

Please enter the IP address <IP-

address>.

The specified user ID is invalid.

The specified password is invalid.


An attempt to communicate with the

Device Manager server has failed. Revise the server.ipaddress

value in the file vds.properties

.

The Device Manager VDS provider can run on Windows Server 2003 only. Please install it on Windows Server 2003.

The IP address is incorrect. Specify the correct IP address.

The user ID contains an invalid character or is too long. Specify the correct user ID.

The password contains an invalid character or is too long. Specify the correct password.

The port number is incorrect. Enter the port address of the CIM HTTP protocol, set for the Device Manager server.

The Device Manager VDS provider cannot be started from the command line. Start

Device Manager VDS Provider as a

Windows service.

Please enter the Device Manager server port address <port-

address>.

You cannot start the file hdvmprovider.exe from the command line. Device Manager VDS

Provider must be started as the service.

You cannot start the file xxxx from the command line. The file yyyy must be executed.

xxxx: Internal file

yyyy: Error information batch collection tool ( hdvmgetlogs.bat)

An attempt to open a log file has failed.

An attempt to write to the log file has failed.

An attempt to back up a log file has failed.

You do not have the permissions required to run this program.

This command cannot be started alone.

Execute the command shown by yyyy.

If the log directory (

<

installationdirectory

>\logs

) does not exist, re-install the VDS provider.

Make sure the Read-only check box is not selected for the log file and the log directory.

Free up disk space by deleting any unnecessary files.

Make sure the Read-only check box is not selected for the backup file.

Execute the command as a user who has

OS Administrator permissions.



1-213

Device Manager CLI Messages

When an error occurs, Device Manager CLI produces one or more error messages. An error message consists of a message number and the error message text.

For details on the log files to which the CLI error messages are output, see the

Device Manager CLI manual.

Table 1-19 lists the Device Manager CLI error messages, and provides

recommended actions for resolving the error conditions. The error messages are listed in numerical order by error code.

Table 1-19 Device Manager CLI Errors

Error Code

KAIC00000-E

KAIC90000-E

KAIC90001-E

KAIC90002-E

KAIC90003-E

KAIC90004-E

KAIC90005-E

KAIC90006-E

KAIC90007-E

KAIC90008-E

KAIC90009-E

KAIC90010-E

Description

Unknown

An internal error occurred in CLI.

Malformed key/value pair: specified-

key-value (must be in the form key=value)

Malformed parameter key:

specified-key-value (must be in the form key=value)

Malformed parameter value:

specified-key-value (must be in the form key=value)

An argument is required for the option specified-option

The option "specified-option" is not valid

Value of key-name must be an integer; could not parse specified-

value

An invalid value "parameter-value" has been specified for parameter

"parameter-name".


"parameter-name".

"LogicalUnit" must be specified in parameter "error-parameter-name" before using parameter "related-

parameter-name".


"parameter-name".










Error Code

KAIC90011-E

KAIC90012-E

KAIC90013-E

KAIC90014-E

KAIC90015-E

KAIC90016-E

KAIC90017-E

KAIC90018-E

KAIC90019-E

KAIC90020-E

KAIC90021-E

KAIC90022-E

KAIC90023-E

KAIC90024-E

KAIC90025-E

KAIC90026-E

KAIC90027-E

KAIC90028-E


Value of channelspeed must be an integer. You entered "specified-

value".

Cannot query Logical Group for contained elements of type

"element-type"

Model = model-name not supported.

Parameter "wwn" must have at least two WWNs.

The list element element-name could not be added to the Host as a

WWN

If either serial number or model is specified for an array, both must be specified

Value of devnums must be a positive integer. You entered

"specified-devnums-value".

Value of devnum must be a positive integer. You entered "specified-

devnum-value".

Could not translate to a WWN from

wwn-string: detail-message

There is no way to make a WWN for

"management-object".

The object type cannot be determined.

The specified object is not a path.


"parameter-name".

"parameter-name" must be specified in parameter "relation-

paramater-name(1)" before using parameter "relation-paramater-

name(2)".

Cannot query parameter-name without relation-paramater-name(1) in relation-paramater-name(2)

"model-name" is not a model name recognized by Device Manager CLI.

The model does not support the command "specified-command".

Modifying Option Definitions while parsing is illegal






If the problem persists, contact the

Support Center.



1-215

1-216

Error Code

KAIC90029-E

KAIC90030-E

KAIC90031-E

KAIC90032-E

KAIC90033-E

KAIC90034-E

KAIC90035-E

KAIC90036-E

KAIC90037-E

KAIC90038-E

KAIC90039-E

KAIC90040-E

KAIC90041-E

KAIC90042-E

KAIC90046-E

KAIC90047-E

KAIC90048-E

KAIC90049-E

KAIC90050-E

KAIC90051-E


Option already defined using character "define-option-character"

- existing-option-name; cannot define option define-option-name

Option already defined long option

"define-option-name" - existing-

option-character; cannot define

define-option-character

Could not correctly parse xml to determine service


Revise the specified XML.

Bad URL

Invalid response received

Could not correctly parse response xml

An error occurred while receiving a response. Make sure the URL is correct, and the server is usable.

Cause: URL

Unexpected error

Invalid Virtual List String - String is null or length is zero

Invalid Virtual List String - length must be even

Invalid Virtual List String - string not in hex format

Revise the specified URL.


Revise the options, URL, and server settings. Make sure that the URL host name is the same as the host name set on the server. If an error still occurs, contact the Support Center.


Failed to add the WWN : error-WWN Revise the specification.

The same WWN "WWN" has existed in the same parameter. invalid parameter value: specified-

parameter-value

Invalid WWN : specified-WWN,

WWN should be "*.*.*.*.*.*.*.*" format. "*" is one or two hexadecimal numbers.

The Alerts element cannot contain that element.

The value: long-value of attribute

attribute-name could not be read as a long value

Illegal value for attribute-name:

specified-date; must be in the form:

required-date-format

The method for reading the XML data cannot be initialized.

An unexpected type or value was detected in the XML response.






Error Code

KAIC90052-E

KAIC90053-E

KAIC90054-E

KAIC90055-E

KAIC90056-E

KAIC90057-E

KAIC90058-E

KAIC90059-E

KAIC90060-E

KAIC90061-E

KAIC90062-E

KAIC90063-E

KAIC90064-E

KAIC90065-E

KAIC90066-E

KAIC90067-E

KAIC90068-E

KAIC90069-E

KAIC90070-E

KAIC90071-E

KAIC90072-E

KAIC90073-E

KAIC90074-E

Description

CommParameters elements cannot contain element-name elements

Parameters elements must have a

"name" and a "value" attribute

An unexpected element was detected in the XML response.

Program Error: Could not read file contents

An unexpected element was detected in the XML response.

The object cannot be created.

An unexpected object has been specified.

An unexpected type or value was detected in the XML response.

Malformed XML HTTP Request

Device Manager does not recognize

root-element-name root element

All Device Manager messages must have an <APIInfo> element

All Device Manager Requests must be in <Request> elements

All Device Manager Requests elements must contain a Module

Element

Device Manager module element must contain a command element

Command element must contain a target attribute

All Device Manager Responses must be in <Response> elements

All Device Manager Responses elements must contain an

EchoCommand Element

Status value of: status-value is not one of the allowed values (FAILED |

PROCESSING | COMPLETED)

Service Module must be specified before writing XML

Command must be specified before writing XML

Command target must be specified before writing XML

Attribute " attribute-name of

Element <element-name> has value= attribute-value; integer value is required

Malformed XML HTTP Response






1-217

1-218

Error Code

KAIC90075-E

KAIC90076-E

KAIC90077-E

KAIC90078-E

KAIC90079-E

KAIC90080-E

KAIC90081-E

KAIC90082-E

KAIC90083-E

KAIC90084-E

KAIC90085-E

KAIC90086-E

KAIC90087-E

KAIC90088-E

KAIC90089-E

KAIC90090-E

KAIC90091-E

KAIC90092-E

KAIC90093-E

KAIC90094-E


All Device Manager Responses must been <Response> elements

XML Conversion Unavailable: missing class file

Cannot interpret the element

<element-name>

The object cannot be converted to

XML.

Contact the Support Center. requires concurrence on date format

The value has an unexpected type.

Revise the specification. The value: attribute-value of attribute attribute-name could not be read as a value of type type-

name

Device Manager Exception, code=

result-code, level= error-level, source= error-source, description=error-description

Device Manager Server Exception:

error code= result-code

error level= error-level

error source= error-source

description=error-description


Refer to the error code in the "Device

Manager Server Messages" section in the

Hitachi Device Manager Software Error

Codes manual, and then perform the corresponding Recommended Action.

Refer to the troubleshooting in the CLI manual.

Server returned the following HTTP

Response: "response"; no additional information available

No Response Returned from the

Device Manager Server

For any-command the option option must be specified

For the command-name command, the option option must be specified

Could not open the file trace-file-

name for writing the message trace

Could not open the file input-

redirect-file-name for reading the input

Could not open file log-file-name for

Logging; will log to console

Must supply a URL from the command line or in the properties file



Could not read password from file

password-file-name

Could not find the password file

password-file-name

Error reading the password file

password-file-name: cause

Revise the contents of the password file.

Revise the password file specification.

Make sure the status of the password file is correct.



Error Code

KAIC90095-E

KAIC90096-E

KAIC90097-E

KAIC90099-E

KAIC90100-E

KAIC90101-E

KAIC90102-E

KAIC90103-E

KAIC90104-E

KAIC90105-E

KAIC90106-E

KAIC90107-E

KAIC90108-E

KAIC90109-E

KAIC90112-E

KAIC90113-E

KAIC90114-E

KAIC90115-E

Description

Certificate from Server shows a hostname of cert-host-name, but the response is actually from url-

host-name

Could not open the file output-

redirect-file-name for writing the output

An attempt to read the property file

"property-file-name" has failed.

Error reading property-file-name from executing directory



Make sure the user has permission to access the specified file.

Revise the file specification, then retry.

An attempt to read the property file

"property-file-name" has failed.

Executing with no property-file-

name Property File

Unrecognized command: command-

name

For the command-name command, the key value must be specified

For the command-name command, the item-option-name(1) or the

item-option-name(2) must be specified

For the command-name command, both the item-option-name(1) and the item-option-name(2) can not be specified together.

Specified parameters not appropriate for the command: family = model-name not recognized;

Subtarget specified-subtarget not recognized; currently supporting:

storage-array-subtarget-names

PDEV devnum from the key-name was not an integer: specified-

pdevnums

In the command-name command, when specifying specified-operand, you have to specify not-specified-

operand

The "attribute-name(channel-

speed)" command is not supported on this subsystem.

Value of key must be either true or false; the value specified-value is neither

The object type cannot be determined.

Check and, if necessary, revise the specified path setting and the status of the file, and then make sure the file can be accessed.

Revise the file specification, then retry.




Revise the specified groupelements, then retry.



1-219

1-220

Error Code

KAIC90116-E

KAIC90117-E

KAIC90118-E

KAIC90119-E

KAIC90120-E

KAIC90121-E

KAIC90122-E

KAIC90123-E

KAIC90124-E

KAIC90128-E

KAIC90129-E

KAIC90130-E

KAIC90131-E

KAIC90132-E

KAIC90133-E

KAIC90134-E

KAIC90135-E


Parameters wwn and domain cannot both be specified.

Either devnum or lusedevnums must be specified

Parameter option-name(1) ignored, using option-name(2) for LUSE definition

"option-name(1)" and "option-

name(2)" can not be specified together.

When "option-name(1)", "option-

name(2)", "option-name(3)"(or

"option-name(4)") and "option-

name(5)" are specified, they must be specified together.

When "option-name(1)", "option-

name(2)", "option-name(3)" and

"option-name(4)" are specified, they must be specified together.

The objectid is required when either

"option-name(1)" or "option-

name(1)" is specified with "option-

name(2)".

Date-Time entered (specified-value) not in the required format:

YYYY/MM/DD HH:MM:SS

Duplicate execution is not allowed:

RefreshStorageArrays



Wait until the executing command finishes, then retry.

Option option-name requires an argument option Revise the specification.

Contact the Support Center. option-name is in the longOptionMap. but not in the charOptionMap under option-

character

option-name is in the charOptionMap. but not in the longOptionMap problem accessing the Device

Manager datatype

Value of key-name must be a long; could not parse specified-value

The CLI initialization information is invalid.

Invalid character was detected in the specified userid or password.

The number of values of

"parameter-name" and "parameter-

name" must be same.






Error Code

KAIC90136-E

KAIC90137-E

KAIC90138-E

KAIC90139-E

KAIC90140-E

KAIC90141-E

KAIC90142-E

KAIC90143-E

KAIC90144-E

KAIC90145-E

KAIC90146-E

KAIC90147-E

KAIC90148-E

KAIC90149-E

KAIC90150-E

KAIC90151-E

Description

The certificate file ("specified

certificate file path") does not exist in the specified path, or the certificate file is invalid.

The certificate file ("default

certificate file path") does not exist in the default path, or the certificate file is invalid.

When the -s option is used, URLs must start with https.

A connection cannot be established.

(reason = "reason why the

connection cannot be established")


Make sure the certificate file is in the specified path and is valid. If you cannot identify the cause of the problem, download the certificate file again.

Make sure the certificate file is in the default path and is valid. If you cannot identify the cause of the problem, download the certificate file again.

Make sure the specified option and URL are correct.

Take action based on the information contained in the message and make sure that the Device Manager Server is running.

Make sure the objectID is correct. The specified objectID "specified

objectID" is invalid.

The API version "specified-API-

version" specified in the XML request is invalid.

An internal error occurred. The CLI

API version "CLI-API-version" is invalid.

The API version "specified-API-

version" specified in the XML request exceeds the highest usable version "highest-usable-version".

Both "Parameter name (1)" and

"Parameter name (2)" must be specified.

The model of the subsystem must be specified when the parameter

"Parameter name" is specified.


parameter-name.


parameter-name. Specify the value by using an integer, CU:LDEV syntax or LDKC:CU:LDEV syntax.


parameter-name. Specify the value by using an integer (decimal or hexadecimal).

Specify either "arraygroupname" or

"chassis" and "groupnum".

"arraygroup" cannot be specified together with "chassis" and

"groupnum".

Specify either "Parameter name (1)" or "Parameter name (2)".

Revise the API version specification.


Revise the API version specification.




1-221

1-222

Error Code

KAIC90152-E

KAIC90153-E

KAIC90154-E

KAIC90155-E

KAIC90156-E

KAIC90157-E

KAIC90158-E

KAIC90159-E

KAIC90160-E

KAIC90161-E

KAIC90162-E

KAIC90163-E

KAIC90164-E

KAIC90165-E

KAIC90167-E

KAIC90168-E


Information in the message was omitted because the message is too long. The original message is as follows:

The object ID of the host or the host name cannot be specified at the same time as the filter used for selecting the host.


parameter-name.

When "parameter-value" is specified for "parameter-name", you must specify the value for "parameter-

name".

When "parameter-value" is specified for "parameter-name", you cannot specify the value for "parameter-

name".

For this model, parameter-value cannot be specified for parameter-

name.

If "parameter-name" is omitted,

"parameter-name" cannot be used.

The user ID or password is not specified. Specify a user ID and password to discover the specified subsystem.

The parameter param0 cannot be specified for this model.

The parameter param0 must be specified for this model

If the parameter param0 is omitted, the parameter param1 must be specified.

Specify one of the following:

parameter-name, parameter-name,


parameter-name, or parameter-

name.

The "command-name" command is not supported on this model.

Specify one of the following:


parameter-name, or parameter-

name.

"hostname" is not recognized as a virtualization server.

This command is not supported on virtualization server.





Revise the specified values.








Use RefreshVirtualizationServer to refresh the virtualization server.



Error Code

KAIC90169-E

KAIC90170-E

KAIC90171-E

KAIC90180-E

KAIC90181-E

KAIC90182-E

KAIC90200-E

KAIC90201-E

KAIC90202-E

KAIC90203-E

KAIC90204-E

KAIC90500-E

KAIC90501-E

KAIC90503-E

KAIC90504-E

KAIC90505-E

Description

No virtualization server or the management software mananging the virtualization servers could be detected.

The parameter "parameter-name" cannot be specified for this Host.

The "specified-command" command is not supported on this Host.

The length of the "parameter-name" parameter is outside the valid range from "minimum-value" to

"maximum-value".

When "option-name(1)","option-

name(2)" and "option-name(3)" are specified, they must be specified together.

The specified parameter

"Parameter-Name" is not appropriate.

The number of "iscsiname" values must match the number of

"iscsinickname" values.

The string "element-name" could not be added to the host as an iSCSIName.

An attempt to add the iSCSIName

"error-iSCSIName" has failed.

The same iSCSIName "iSCSIName" is already specified in the parameter.

The iSCSIName cannot be specified for the instance "management-

object".

Options "-b" and "-i" cannot be specified at the same time.

A command or parameter cannot be specified when option "-b" is specified.

Both "Command name" and

"Command name" are included in the command specifications in the specified batch file. Only one of these commands can be included in the batch file.

The number of commands that can be included in the batch file is

"Number".

A command "Command-Name" that cannot be executed by batch execution has been coded in the batch file.


Revise the parameter settings and the virtualization software settings.








Revise the contents of the batch file.



1-223

1-224

Error Code

KAIC90506-E

KAIC90507-E

KAIC90508-E

KAIC90509-E

KAIC90510-E

KAIC90511-E

KAIC90512-E

KAIC90513-E

KAIC90550-E

KAIC90551-E

KAIC90552-E

KAIC90553-E

KAIC90556-E

KAIC90557-E

KAIC90559-E

KAIC90560-E

KAIC90562-E

KAIC90563-E

Description

The specified batch file cannot be found.

An attempt to read the specified batch file has failed. Remove the cause of the problem, and then reexecute the batch file. Cause:

"Message"

No command has been coded in the batch file.

The commands coded in the batch file must be for a single subsystem.

The batch file contains invalid coding in line Line-Number.

An error occurred while reading the batch file. Revise the coding in the batch file, and then re-execute the batch file. Line:Line-Number Cause:

Message

The specified parameter

"Parameter-Name" is not appropriate for the command

"Command-Name".

The specification of parameter

"Parameter-Name" is duplicated in the command.

There is an error in the syntax of the batch file coding.

The coding that follows the endbatch line is invalid.

The beginbatch line is not coded.

A command or endbatch line is not specified.

The coding in the beginbatch line is invalid.

The coding in the endbatch line is invalid.

A space character is required before the command name.

Characters other than alphanumeric characters cannot be used in a command name.

The batch file contains invalid coding.

Characters other than alphanumeric characters cannot be used in a parameter name.


Revise the batch file specification.

Remove the cause of the problem, and then re-execute the batch file.


Revise the contents of the batch file, then retry.






Error Code

KAIC90564-E

KAIC90565-E

KAIC90566-E

KAIC90569-E

KAIC90570-E

KAIC90571-E

KAIC90572-E

KAIC90573-E

KAIC90574-E

KAIC90575-E

KAIC90576-E

Description

The parameter specification is invalid. The parameter name is incorrect or the parameter has not been specified using the

"parameter-name=value" syntax.

An invalid character is being used in the parameter value. Only ASCII characters can be used. Escaping by

"\" is required for spaces and symbols, except for: ",", "-", ".",

"/", ":", "=", "_", ";".

Characters other than symbol characters cannot be escaped. The characters that can be escaped are:

" ", "!", """, "#", "$", "%", "&", "'",

"(", ")", "*", "+", "<", ">", "?", "@",

"[", "\", "]", "^", "`", "{", "|", "}",

"~".

A new line is required at the end of a statement.

The maximum number of characters that can be specified for a name, such as a parameter name, is

"Length".

This is an invalid line. A line feed is required after a carriage return.

If you specify "parameter-key-

name", you must also specify

"parameter-key-name". If you specify "parameter-key-name", you must also specify "parameter-key-

name".

If you specify "parameter-key-

name" and "parameter-key-name", you must also specify "parameter-

key-name" and "parameter-key-

name".

The memory for the CLI became insufficient while this operation was being performed.


Revise the command parameters, then reexecute the command.

Take either of the following actions:





Increase the memory heap size for the

CLI, and then perform the operation again.

Decrease the amount of information to be collected, and then perform the operation again.

Specify a valid value. The value of the "parameter-key-

name" parameter is outside the valid range from "minimum-value" to "maximum-value".

The sum of startElementNumFilter and numOfElementsFilter is outside the valid range from "minimum-

value" to "maximum-value".



1-225

1-226

Error Code

KAIC90577-E

KAIC90600-E

KAIC90601-E

KAIC90602-E

KAIC90603-E

KAIC90701-E

KAIC90702-E

KAIC90703-E

KAIC90704-E

KAIC90705-E

KAIC90706-E

KAIC90707-E

KAIC90708-E

KAIC90709-E

Description

The "parameter-name-list" and

"parameter-name-list" parameters cannot be specified at the same time.

An invalid value "specified-value" has been specified for the option

"specified-option".

The options "specified-option" and

"specified-option" cannot be specified at the same time.

The option "specified-option" and the command "specified-command" cannot be specified at the same time.

The option "specified-option" and the parameter "specified-

parameter" cannot be specified at the same time.

The user ID specified for the option

-u does not match the user ID in the property file property-file-name.

The password specified for [Old password] does not match the password in the property file

property-file-name.

The passwords specified for [New password] and [Re-enter new password] are not the same.

An attempt to encode the password has failed.



Specify the correct user ID at the command line.

Specify the correct password at the command line. If the password in the property file cannot be specified correctly at the command line, delete the password from the property file, and then execute the command again.

Specify the correct password at the command line.

An attempt to decode the password has failed.

Revise the execution environment, and then execute the command again. If the problem persists, please contact the

Support Center.

Specify the correct user ID that corresponds to the password set in the password2 option. If the problem persists, please contact the Support Center.

Delete the password in the property file, and then execute the command again.

An attempt to decode the password failed because the current environment is different from the environment in which the password was encoded.

Command execution failed because the environment does not support the specific encoding algorithm.

I/O processing for a file failed or was interrupted. (cause = Message)

An invalid password was specified.


Support Center.

Remove the cause of error by referring to the error information in the message, and then execute the command again.

Check which characters are valid and the maximum number of characters for a password, and then specify a valid password.



Error Code

KAIC90710-E

KAIC90711-E

KAIC90712-E

Description

An attempt to encode or decode the password failed because the execution environment was invalid.

An attempt to encode or decode the password failed because the execution environment was invalid.

The password file password-file-

name could not be written to.




Support Center.

If the password file exists, grant write access for it. If it does not exist, grant write access so that a password file can be made.



1-227

Device Manager CLIEX Messages

When an error occurs, Device Manager CLIEX produces one or more error messages. An error message consists of a message number and the error message text.

For details on the log files to which the CLIEX error messages are output, see the Device Manager CLI manual.

Table 1-20 lists the Device Manager CLIEX error messages, and provides

recommended actions for resolving the error conditions. The error messages are listed in numerical order by error code.

Table 1-20 Device Manager CLIEX Errors

Error Code

KAIC40001-E

KAIC40002-E

KAIC40003-E

~ KAIC40699-

E

KAIC41000-E

Description

An unknown failure occurred in the target storage array.

The command device has failed.

command device error message

RAID Manager error message



Support Center.

See the CCI/RAID Manager manual.

See the Troubleshooting Device Manager

CLIEX Problems and the CCI/RAID

Manager manual.


KAIC41001-E

An internal error occurred. (file =

"file name", line = "line number").

Memory allocation error. Out of memory.

KAIC41002-E

There might not be enough memory to execute Device Manager CLIEX.

Make sure there is enough memory in the system. If the problem persists, contact the Support Center.


KAIC41003-E

KAIC41004-E

KAIC42000-E

KAIC42001-E

KAIC42002-E

This command has not been supported for the target storage array.

An attempt to load the command device has failed.

An attempt to acquire the device information has failed. (device special file: "device file name")

Check the status of the device associated with the device special file.

The storage-array parameter must be one of the following: "-c", "-cmddev", "-a", or "--array"

The storage-array parameter must be one of the following: "-c", "-cmddev", "-a", or "--array"

The specified storage array name

"alias name" is invalid. Check the property file.

Make sure that the host is recognizing the command device correctly.

Check the status of the device associated with the device special file.


Support Center.


Make sure the contents of the property file are correct, then revise the storage subsystem specification.



Error Code

KAIC42003-E

KAIC42004-E

KAIC42005-E

KAIC42006-E

KAIC42007-E

KAIC42008-E

KAIC42009-E

KAIC42010-E

KAIC42011-E

KAIC42012-E

KAIC42013-E

KAIC42014-E

KAIC42015-E

KAIC42016-E

KAIC42017-E

KAIC42018-E

KAIC42019-E

KAIC42020-E


A command argument is missing or invalid.

The command must contain only one of the following: command list

The value "parameter value" for the parameter "parameter name" is invalid.

The value for the parameter

"parameter name" must be between

minimum value and maximum

value.

The parameter "parameter name" is required.

The parameter "parameter identifier

or parameter name" is invalid.

The parameter must be either

"parameter name" or "parameter

name".

The LUN "path LUN" has already been assigned to a LUN group or is not assigned to this port.

The specified LDEV "device number" is invalid.

The specified LDEV "device number" is part of the LU joined by the LUSE.

The LU "device number" is not assigned to the port "port number".

Revise the command specification.


Collect the storage subsystem information, and then make sure the parameter specification is correct.


The LUN "path LUN" is already being used.

To perform this operation,

"LUNSecurity=On" must be set for the port.

The LU "device number" is already assigned to this port.


Revise the LUN specification.

Turn on the security switch for the specified port, then retry.


The LU "device number" is not assigned to "port-number - host

storage domain ID" (port -

HostStorageDomain).

The LUN "path LUN" is not assigned to the LUN group "LUN group ID".

The host storage domain "host

storage domain ID" already exists on this port.

The WWN "WWN" has not been registered in "LUNGroup or

HSDOMAIN": "LUN group ID or host

storage domain ID".



1-229

1-230

Error Code

KAIC42021-E

KAIC42022-E

KAIC42023-E

KAIC42024-E

KAIC42025-E

KAIC42026-E

KAIC42027-E

KAIC42028-E

KAIC42029-E

KAIC42030-E

KAIC42031-E

KAIC42100-E

KAIC42996-E

KAIC42997-E

KAIC42998-E

Description

The WWN "WWN" has already been defined in the host storage domain

"host storage domain ID".

The maximum LUN number

("maximum value") on the port has been reached.

The host storage domain "host

storage domain ID" has not been defined for the port "port number".

The LU "path LUN" has already been assigned to a port.

target volume is not available for this operation.

The usual volume and the V-VOL can not be specified together.

At least one LUN is necessary for the pair volume.

Duplicated value "parameter value" for parameter name is specified.

The LU "device number" is already assigned to this host storage domain.

ARRAY: "array name" is not attached this host or doesn't have valid CMDDEV.

The Command Device

(devNum="device number", devFile="device file name") is not attached this host. Or, the storage array that has the Command Device is not supported. Revise devFile or devNum in the property file.

Permission denied with the Virtual

Partition Manager, "parameter

name": "parameter value".

Device Manager CLIEX cannot be started because the installation directory in the registry is invalid.

Re-install Device Manager CLIEX. If this problem cannot be solved, contact the Support Center.

Device Manager CLIEX cannot be started because a registry entry is invalid. Re-install Device Manager

CLIEX. If this problem cannot be solved, contact the Support Center.

Device Manager CLIEX cannot be started because the registry key is invalid. Re-install Device Manager

CLIEX. If this problem cannot be solved, contact the Support Center.


Make sure that the host is recognizing the command device correctly.

Make sure that the host is recognizing the command device correctly, and that the storage subsystem for the command device is supported by Device Manager

CLIEX.




Make sure the host storage domain is correct.


Revise the volume specification.

Revise the LUN specification.



If the problem cannot be solved, contact the Support Center.



Error Code

KAIC42999-E

KAIC43300-E

KAIC43301-E

KAIC43302-E

KAIC43303-E

KAIC43500-E

KAIC43502-E

KAIC43503-E

KAIC43504-E

KAIC43505-E

KAIC43506-E

KAIC43550-E

KAIC43551-E

KAIC43552-E

KAIC43553-E


The specified value "specified value" does not exist on the target "target

element".

An attempt to load "file name" has failed.

The filename cannot contain any directories.

The file "file name" cannot be loaded.

The file cannot be opened. ("file

name")



Revise the property file specification.


There are too many or too few elements in the message file. (file =

"file name", line = "line number", string = "line string")

The log level in the message file is invalid. (file = "file name", line =

"line number", string = "line string")

The message ID in the message file is invalid. (file = "file name", line =

"line number", string = "line string")

A definition is duplicated in the message file. (file = "file name", line = "line number", string = "line

string")

The number of sections in the message file is invalid. (file = "file

name", line = "line number", string

= "line string")

The message file "file name" is missing the message "message ID".

The file cannot be opened. ("file

name")

The file cannot be written to. ("file

name")

An attempt to open the event log has failed. Check the event log settings or change the Device

Manager CLIEX settings so that event logs are not output to the event log.

An attempt to output to the event log has failed. Check the event log settings or change the Device


Revise the configuration of the property file. If the problem persists, contact the

Support Center.


Revise the event log settings.



1-231

Error Code

KAIC43554-E

KAIC44300-E

KAIC44301-E

KAIC44302-E

KAIC44303-E

KAIC44304-E

KAIC44305-E

KAIC44306-E

KAIC44400-E

Description

An attempt to close the event log has failed. Check the event log settings or change the Device


The XML is invalid. (file = "file

name", line = "line number", column = "column number",

"message")

The XML is not well formed. (file =

"file name", line = "line number", column = "column number",

"message")

An error occurred during XML parser initialization. (file = "file name")

An error occurred during parsing.

("error message")

A DOM error occurred during parsing. ("error message")

An error occurred during parsing.

("error message")

An error occurred during XML processing. ("error message")

An error occurred while parsing "file

name". This file does not conform to the DTD.


Revise the event log settings.

Make sure the contents of the property file are correct.


Support Center.



Support Center.




HiCommand® Device Manager Error Codes

Hitachi Device Manager Messages

Device Manager Server Messages

Device Manager Web Client Messages

Device Manager Agent Messages

Device Manager Agent's Provisioning Manager Messages

Device Manager Agent's Replication Manager Messages

Device Manager VDS Provider Messages

Device Manager CLI Messages

Device Manager CLIEX Messages

Key Features

Frequently Answers and Questions

What is the Hitachi Device Manager?

What are the main functions of the Hitachi Device Manager?

What types of storage devices can be managed by the Hitachi Device Manager?

How can I access the Hitachi Device Manager?

Table of contents