HiCommand® Device Manager Error Codes

Universal Storage Platform V/VM

Messages

This chapter lists and describes the Hitachi Device Manager storage subsystem error messages for Universal Storage Platform V/VM.



Details About Universal Storage Platform V/VM Messages

Universal Storage Platform V/VM Messages

Hitachi Device Manager Error Codes

2-1

Details About Universal Storage Platform V/VM Messages

Some messages displayed by Device Manager contain, as a part of the message, a message output from the storage subsystem. This section lists and describes the error messages from Universal Storage Platform V/VM that are contained in Hitachi Device Manager messages.

If you are unable to resolve the conditions of an error, see

Calling the Hitachi

Data Systems Support Center for instructions on calling the Hitachi Data

Systems Support Center.

When a Device Manager message contains a message from Universal Storage

Platform V/VM, Device Manager displays two types of error code identifying the Universal Storage Platform V/VM messages.

Table 2-1 lists and describes the Universal Storage Platform V/VM messages

that are displayed by Hitachi Device Manager. For details on the Universal

Storage Platform V/VM error messages that are not listed in Table 2-1, see the

Storage Navigator message manual. In those messages, %s indicates a string variable and %d indicates a numerical variable.

Messages whose first error code (error code 1) is 60xx (where xx is a two-digit number) are TrueCopy for z/OS or TrueCopy messages. This manual contains

TrueCopy for z/OS messages only. If you are a TrueCopy user, note that:



The word M-VOL in TrueCopy for z/OS messages is equivalent to P-VOL in

TrueCopy messages.



The word R-VOL in TrueCopy for z/OS messages is equivalent to S-VOL in

TrueCopy messages.

Note:

 The list of messages below shows error codes 1 and 2, separated by a comma. The asterisk ("*") indicates that the error code output varies. If a displayed error code does not match any of the codes listed below, see the explanation for the message labeled *,*.

 In some cases, the Recommended Action column may be blank. In these circumstances, the user should take actions based on instructions provided in the error message and based on what the user is trying to accomplish.

2-2 Universal Storage Platform V/VM Messages


Table 2-1 Universal Storage Platform V/VM Messages

Error Code

*,*

2,5510

2,56525

2,58578

3,2003

3,2033

3,2100

5,66101

305,56525

405,5047

Description

An error has occurred in the subsystem. If you cannot solve this problem, contact the Support Center.

The disk subsystem is in internal process, or some other user is changing the configuration. Wait a while, then click

[Refresh] on the File menu, or wait a while and login again.

Because the settings across the multiple

SLPRs are contained, the authority has been shifted to the storage administrator from the storage partition administrator.

To continue the operation, please contact the storage administrator. To perform other operations, select a function button.

An error occurred in the disk subsystem.

The configuration may be inconsistent.

Please select [All Refresh] and refresh the configuration.

Volume migration, QuickRestore, etc. are in process. After you reply to this message, a window that shows only the

Refresh button will be displayed. Please wait for a while, and then select

[Refresh].

Wait a while, then click [Refresh] on the

File menu, or wait a while and login again.

See the Storage Navigator message manual.


After you reply to this message, a window that shows only [Refresh] will be displayed. Wait a while, then click

[Refresh].If this problem persists, inconsistency of configuration may have occurred. Please call the Support Center.

If the problem occurred when starting

SVP, check the version number of the microprogram and the configuration information.


The SVP is not ready yet, or an internal processing is being executed. Wait for a while, and then click [Refresh] on the File menu. When an error occurs during login, wait for a while and login again.

An error occurred while connecting to the disk subsystem. The configuration may be inconsistent. Please select [All Refresh] and refresh the configuration.

This function could not be used because a function failed to start during SVP initialization.Click [All Refresh] and refresh the configuration. If this problem persists, please call the Support Center.




An error occurred when installing or uninstalling the program product. Please select the program product and select





Recommended Action

If the problem persists, contact the

Support Center.



2-3

2-4

Error Code

405,5503

605,8971

605,66501

605,66502

605,66503

605,66504

605,66505

605,66506

605,66507

605,66508

605,66509

605,66512

605,66514

605,66515

605,66517

605,66518

605,66675

605,66693

Description

[Detail] to check the details of the error.

You have attempted to install an

Emergency key to the option for which a

Permanent key has been installed. If you want to install the Emergency key forcibly by using the license key file, please specify Only Normal & Warning and retry this operation. If you want to install the

Emergency key forcibly by using the license key code, please select [OK].

An error occurred while connecting to the disk subsystem. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration.

The number of LDEVs that can be defined in an external volume has exceeded the maximum value.

Specified ExG has already been used.

It is not set within the range where LDKC,

CU, and LDEV can be used.

Specified LDKC:CU:LDEV has already been used.

It is allocated in other emulation groups within the delimited range of each

32LDEV number.

Specified SSID has already been used.









The target external volume is blocked or not set within the range where capacity can be used.

The specified LDEV capacity is invalid.



The total of the LDEV capacity defined in the external volume exceeds the external volume size.

Specified CLPR is not mounted.



LDKC: CU that cannot be used by the

SLPR is specified.

SSID that cannot be used by the SLPR is specified.

The target external volume has already been mapped or set.

The cross-subsystem path configuration of the external volume is not corresponding to the cross-subsystem path configuration defined in PathGroup.

The syntax of the parameter is invalid.






A correct parameter is not set as a data


See the Storage Navigator message



Error Code

605,66694

605,66695

605,66698

605,66702

605,66705

605,66710

605,66713

605,66718

605,66720

605,66722

605,66736

605,66739

605,66742

605,66744

605,66747

605,66797

605,66798

605,66799

1005,1128

1005,2100

Description

transfer volume.

A correct parameter is not set as

RemoteCommandDevice.

Specified port is not external port.


manual.




The number of alternate Path definitions that can be set to the external volume has exceeded the maximum.

It is not set within the range where

PathGroup can be used.

It is not Port number that can be specified.

It is not set within the range where LUN can be used.

It is not set within the range where ExG can be used.

It is not set within the range where CLPR can be used.

It is not emulation type that can be specified.

CacheMode is invalid.

It is not set within the range where LDKC can be used.

It is not set within the range where CU can be used.

It is not set within the range where LDEV can be used.

It is not set within the range where LDEV capacity can be used.

It is not set within the range where SSID can be used.

There is an error in the parameter of the subordinate position hierarchy.

Specified WWN was not found.

















Specified external volume was not found. See the Storage Navigator message manual.

Review the Channel Package. You have requested to change the channel speed, but the version of Fiber

PCB is not supported.

An error occurred while connecting to the disk subsystem. The configuration may be inconsistent. Please select [All Refresh]




2-5

2-6

Error Code Description

and refresh the configuration.

1005,56525 Because the settings across the multiple


1305,66572 Declaration is invalid.

1305,66573 The number of lines or the number of characters in one line exceeds the maximum number.

1305,66574 There is a line that cannot be interpreted as an element of the spreadsheet.

1305,66575 It is not corresponding to the serial number of the device that executes the spreadsheet.

1305,66576 Any operation tag to the program product is not set.

1305,66577 Version number or program product of the declaration is not correct.

1305,66578 There was an error while executing the spreadsheet. Please confirm the result of each parameter.

1305,66675 The syntax of parameter is invalid.










3005,8971 An error occurred while connecting to the disk subsystem. The configuration may be inconsistent. Click [Refresh All] on the File menu and refresh the configuration.




3005,58572 An error occurred during the communication with the storage system.

Please wait a while, and retry the operation.If the error occurred in the operation of the pool, please refresh the configuration by clicking [Refresh All] on the File menu, then retry the operation.




5105,56525



To continue the operation, please contact









Error Code Description

the storage administrator. To perform other operations, select a function button.







8005,5510 The disk subsystem is in internal process, or some other user is changing configuration. After you reply to this message, a window that shows only the

Refresh button will be displayed. Please wait for a while, and then select

[Refresh].




8105,2033 The SVP is not ready yet, or an internal processing is being executed.

8105,6999 There is a possibility that composition information has been changed.

9605,56525














2-7

2-8 Universal Storage Platform V/VM Messages


HiCommand® Device Manager Error Codes

Universal Storage Platform V/VM

Messages

Details About Universal Storage Platform V/VM Messages

Key Features

Frequently Answers and Questions

What is the Hitachi Device Manager?

What are the main functions of the Hitachi Device Manager?

What types of storage devices can be managed by the Hitachi Device Manager?

How can I access the Hitachi Device Manager?

Table of contents