advertisement
DVRN960 User
’s Manual
2. System Setup
The notices and introduction on system installation will be described in this chapter. Please follow these descriptions to operate the unit.
In order to prevent the unit from data loss and system damage that caused by a sudden power fluctuation, use of an Uninterruptible Power Supply (UPS) is highly recommended.
2.1 Position the Unit
First, note to position / mount the DVR in a proper place and be sure to power off the unit before making any connections. The placed location should avoid hindering or blocking the unit from airflow. Enough airflow is needed to protect the unit from overheating. The maximum allowable temperature of operating environment is 40°C.
The unit utilizes heat-conducting techniques to transfer internal heat to the case, especially to the bottom side of the unit.
NOTE: Be sure the rubber feet are not removed, and always leave a space for air ventilation on the bottom side of the unit.
2.2 Connect Devices to the Unit
This section lists some important notices that should be read before making any connection to the DVR.
Connecting Required Devices
Before powering up the unit, a USB mouse, cameras, and a main monitor should be connected to the unit for basic operation. If needed, connect a call monitor for displaying full-screen video of all installed cameras in sequence.
Connecting Short-term Device
If any short-term devices shall be installed to the DVR as parts of the unit system, such as USB ThumbDrive® or any USB devices, etc, make sure those devices are connected only after the DVR is powered up. The reason is the DVR can recognize the external devices only after the power-up process is done completely.
8
advertisement
Related manuals
advertisement
Table of contents
- 8 Overview
- 9 System Setup
- 9 Position the Unit
- 9 Connect Devices to the Unit
- 10 Rear Panel Connections
- 12 General System Setup
- 12 USB Mouse Operation
- 13 Functional Icons
- 14 Enter OSD Setup Menu
- 15 User Management
- 16 Power On / Shutdown / Reboot
- 18 HDD Auto Scan
- 19 System Date / Time Setting
- 19 Set Date / Time
- 20 Daylight Saving Time
- 20 Network Time Protocol Setup
- 21 Record Schedule / Quality Setting
- 22 Record Mode Setup
- 23 Schedule Setup
- 23 Preset Record Configuration
- 24 ezRecord Setup
- 25 Advance Schedule Setup
- 25 Schedule Table
- 26 Recording Profile Setup
- 26 Holiday Setup
- 27 Data Lifetime Setup
- 28 Circular Recording
- 28 Audio Recording
- 28 Purge Data
- 29 Event Setting
- 29 Internal Buzzer
- 29 Event Icon
- 30 Alert Notification Setup
- 30 Alert Configuration Set
- 30 Alert Notification
- 30 Alert IP
- 30 Alert Port
- 30 Alert Interval
- 31 Event Full Screen
- 31 Event Duration
- 31 Per Channel Config
- 31 Channel Select
- 31 Video Loss Detect
- 32 Motion Detect
- 32 Detection Configuration
- 33 Alarm In
- 33 Alarm Out
- 33 Copy Event Settings
- 34 E-mail Management
- 35 Basic Operation
- 35 View Live / Playback Video
- 35 Viewing Modes
- 35 Digital Zoom
- 36 Camera Info
- 36 View Live Cameras
- 36 Playback Recorded Videos
- 39 Capture Snapshots
- 39 Sequence
- 39 Sequence with Main Monitor
- 39 Sequence with Call Monitor
- 40 Search Recorded Video
- 40 Search by Time
- 41 Calendar Search
- 42 Search by Event
- 43 Video Export
- 43 OSD Export Menu
- 44 Select the External Device
- 44 Select Video for Exporting
- 45 Digital Signature
- 46 Begin Export
- 46 Quick Video Export
- 46 ezBurn Introduction
- 47 Export Normal Video
- 48 Export Event Video
- 48 Dome Control
- 48 Dome Connection
- 49 Dome Protocol Setup
- 49 RS485 Setup
- 50 Dome Control Buttons
- 51 Set Preset Points
- 51 Call Preset Points
- 52 Run Dome Camera Tour
- 52 System Log Exportation
- 53 Remote Monitoring Software
- 53 Remote Monitoring System Requirements
- 54 Software Installation
- 54 Change Internet Settings
- 56 Install the Remote Monitoring Software
- 57 Login / Logout
- 58 Software Upgrades
- 58 Basic Operation
- 58 View Live Video
- 59 Select Display Mode
- 59 Operate Cameras with Dome Control
- 60 Digital Zoom of Camera Display
- 61 Instant Recording
- 61 Record Video Instantly
- 61 Playback Instant Recorded Video
- 61 Playback Video
- 62 Playback Remote Video
- 63 Playback Local *.drv Files
- 63 Playback Controls
- 64 Verify Digital Signature
- 64 Search from Event List
- 65 Take a Snapshot
- 65 Health Status
- 66 Normal and Dual Streaming
- 66 Upgrade Remote Software / Reboot of Connected DVR
- 67 Remote Monitoring Software Troubleshooting
- 69 Appendix A: Keyboard Access Sketch
- 70 Appendix B: Remote Controller
- 72 Appendix: Setup a DVR Behind a Router