advertisement
DVRN960 User
’s Manual
3.5.5 Advance Schedule Setup
When <Adv. Schedule> is selected as the option for <Preset Config>, users need to further configure the schedule and recording setting under this menu.
The Advance Schedule setup menu is shown as below.
Advance Schedule Setup
Schedule Table
Recording Profile Setup
Holiday Setup
NOTE: The <Advance Schedule Setup> menu can only be accessed when <Preset Config> is set to <Adv. Schedule>.
3.5.5.1 Schedule Table
In this menu, users can assign recording type for days in a week by hour.
Moreover, the recording type for pre-defined holidays can also be specified here. Refer to the steps below to setup the schedule table.
24
Click on a preferred recording type at the bottom.
Click at any grid of time to assign the selected recording type.
Click on any hour on the top to fill up the column.
Click on any day on the left to fill up the roll.
Click on the top left grid to always record with the selected recording type.
Click on the <Confirm> button to save the setting.
advertisement
Related manuals
advertisement
Table of contents
- 8 Overview
- 9 System Setup
- 9 Position the Unit
- 9 Connect Devices to the Unit
- 10 Rear Panel Connections
- 12 General System Setup
- 12 USB Mouse Operation
- 13 Functional Icons
- 14 Enter OSD Setup Menu
- 15 User Management
- 16 Power On / Shutdown / Reboot
- 18 HDD Auto Scan
- 19 System Date / Time Setting
- 19 Set Date / Time
- 20 Daylight Saving Time
- 20 Network Time Protocol Setup
- 21 Record Schedule / Quality Setting
- 22 Record Mode Setup
- 23 Schedule Setup
- 23 Preset Record Configuration
- 24 ezRecord Setup
- 25 Advance Schedule Setup
- 25 Schedule Table
- 26 Recording Profile Setup
- 26 Holiday Setup
- 27 Data Lifetime Setup
- 28 Circular Recording
- 28 Audio Recording
- 28 Purge Data
- 29 Event Setting
- 29 Internal Buzzer
- 29 Event Icon
- 30 Alert Notification Setup
- 30 Alert Configuration Set
- 30 Alert Notification
- 30 Alert IP
- 30 Alert Port
- 30 Alert Interval
- 31 Event Full Screen
- 31 Event Duration
- 31 Per Channel Config
- 31 Channel Select
- 31 Video Loss Detect
- 32 Motion Detect
- 32 Detection Configuration
- 33 Alarm In
- 33 Alarm Out
- 33 Copy Event Settings
- 34 E-mail Management
- 35 Basic Operation
- 35 View Live / Playback Video
- 35 Viewing Modes
- 35 Digital Zoom
- 36 Camera Info
- 36 View Live Cameras
- 36 Playback Recorded Videos
- 39 Capture Snapshots
- 39 Sequence
- 39 Sequence with Main Monitor
- 39 Sequence with Call Monitor
- 40 Search Recorded Video
- 40 Search by Time
- 41 Calendar Search
- 42 Search by Event
- 43 Video Export
- 43 OSD Export Menu
- 44 Select the External Device
- 44 Select Video for Exporting
- 45 Digital Signature
- 46 Begin Export
- 46 Quick Video Export
- 46 ezBurn Introduction
- 47 Export Normal Video
- 48 Export Event Video
- 48 Dome Control
- 48 Dome Connection
- 49 Dome Protocol Setup
- 49 RS485 Setup
- 50 Dome Control Buttons
- 51 Set Preset Points
- 51 Call Preset Points
- 52 Run Dome Camera Tour
- 52 System Log Exportation
- 53 Remote Monitoring Software
- 53 Remote Monitoring System Requirements
- 54 Software Installation
- 54 Change Internet Settings
- 56 Install the Remote Monitoring Software
- 57 Login / Logout
- 58 Software Upgrades
- 58 Basic Operation
- 58 View Live Video
- 59 Select Display Mode
- 59 Operate Cameras with Dome Control
- 60 Digital Zoom of Camera Display
- 61 Instant Recording
- 61 Record Video Instantly
- 61 Playback Instant Recorded Video
- 61 Playback Video
- 62 Playback Remote Video
- 63 Playback Local *.drv Files
- 63 Playback Controls
- 64 Verify Digital Signature
- 64 Search from Event List
- 65 Take a Snapshot
- 65 Health Status
- 66 Normal and Dual Streaming
- 66 Upgrade Remote Software / Reboot of Connected DVR
- 67 Remote Monitoring Software Troubleshooting
- 69 Appendix A: Keyboard Access Sketch
- 70 Appendix B: Remote Controller
- 72 Appendix: Setup a DVR Behind a Router