- Computers & electronics
- Computer components
- System components
- Server/workstation motherboards
- User manual
![](http://s3.manualzz.com/store/data/032423228_1-2071a470cb6531f2f228a83a5c24ab03-128x128.png)
advertisement
![Silicon Graphics® Zx10 Visual Workstation Owner`s Guide | Manualzz Silicon Graphics® Zx10 Visual Workstation Owner`s Guide | Manualzz](http://s3.manualzz.com/store/data/032423228_1-2071a470cb6531f2f228a83a5c24ab03-360x466.png)
Using System Management Software
To use the CD-ROM drive:
• To insert a CD, press the eject button to extend the tray. Place the disc, printed side up, in the tray and press the eject button again to retract the tray.
• To remove a CD, press the eject button, and remove the disc after the tray extends.
Then press the eject button again to retract the tray.
• The media player programs included with the operating system allow you to listen to audio compact discs. Insert an audio CD, printed side up, into the drive and start the media player application. Adjust the volume using the operating system’s sound control programs.
• Adjust the volume control on the drive for headphones connected to the drive.
Using System Management Software
Your system shipped with the following system management software installed:
• Hardware Monitor is an interface to instrumentation data measured by sensors inside the computer. Event information is reported to the Event Log and displayed graphically.
• DMI Console gives easy access to the system’s status and configuration information. DMI Console works with the Desktop Management Interface (DMI), a technology standard that enables the effective management of computers.
• ECC Monitor monitors the system’s error correcting code (ECC) memory and reports any problems.
• SMART Disk Driver (SMARTDRV) is a kernel-level driver that supports self-monitoring, analysis, and reporting technology (SMART) for disk drives.
You can find these programs by going to Programs on the operating system’s Start menu.
See the online Help for each program for more information on how to use it.
Learning About the Operating System
Documentation delivered with your system describes the basic functions of its operating system. Refer to this documentation if you are unfamiliar with the operating system
007-4327-002 59
advertisement
Related manuals
advertisement
Table of contents
- 21 Unpacking the System
- 22 Placing System Components
- 22 Connecting System Components
- 25 Locating Expansion Cards
- 26 Connecting External SCSI Devices
- 28 Connecting to AC Power
- 29 Starting the System
- 30 What’s Next?
- 31 Preparing for Setup
- 33 Going Through Setup
- 35 Finishing Software Setup
- 36 Installing the Network Controller Driver
- 36 Creating an Emergency Repair Disk
- 36 Installing Driver Software
- 37 Installing QFE Software
- 37 What’s Next?
- 39 Configuring the Video Display
- 39 Resetting the Video Display Resolution
- 40 Changing the Default Video Display Driver
- 40 Correcting Initial Video Display Problems
- 41 Configuring System Audio
- 41 Configuring Networking
- 42 Configuring Peripheral Devices
- 42 Changing Drive Letters
- 43 Changing Virtual Memory Settings
- 44 Configuring the SCSI Controller
- 44 Creating or Updating an Emergency Repair Disk
- 45 Configuring the BIOS
- 45 What’s Next?
- 47 Opening and Closing the Door
- 48 Controlling System Power
- 50 Reading System LEDs
- 52 Using Automatic Shutdown
- 53 Starting and Stopping the Operating System
- 54 Observing Operating Precautions
- 54 Using the Keyboard
- 56 Using the Mouse
- 58 Using the Floppy Disk Drive
- 58 Using the CD-ROM Drive
- 59 Using System Management Software
- 59 Learning About the Operating System
- 60 Using Hardware Security Features
- 60 Cleaning System Components
- 61 Getting Started
- 62 System Power
- 62 System Boot
- 66 Video
- 66 Audio
- 67 Network
- 67 Peripheral Drive Errors
- 68 Miscellaneous Hardware
- 71 Before You Begin
- 71 Finding Driver Software
- 72 Installing the Operating System
- 73 Updating the Operating System
- 75 Before You Begin
- 76 Avoiding Electrostatic Discharge
- 76 Removing and Replacing Side Panels
- 78 Removing and Replacing the Faceplate
- 79 System Components
- 81 Before You Begin
- 82 Adding Expansion Cards
- 83 Identifying Expansion Card Slots
- 84 Installing an Expansion Card
- 85 Assigning System Resources
- 85 Disabling On-Board Controllers
- 86 Adding External SCSI Peripheral Devices
- 86 Choosing SCSI Cables
- 87 Choosing SCSI IDs
- 87 Terminating SCSI Devices
- 88 Connecting SCSI Devices
- 89 Changing SCSI Controller or Device Settings
- 89 Adding Internal Peripheral Devices
- 92 Adding Memory
- 92 Upgrading Processors
- 93 Before You Begin
- 94 Floppy Disk Drive
- 95 Front-Access Peripheral Device
- 99 Internal-Access Peripheral Device
- 102 Expansion Card
- 105 Memory Module
- 106 Processor Bus Terminator
- 107 Processor Module
- 107 Power Supply
- 110 Cooling Fans
- 113 System Board
- 115 CMOS/Clock Lithium Battery
- 116 Chassis Intrusion Alarm Switch
- 117 Power Switch, System LEDs, and Light Pipe
- 121 Functional Diagram
- 122 Internal Peripheral Cabling
- 123 EIDE Cabling
- 123 SCSI Cabling in a Zx10 System
- 124 SCSI Cabling in a Zx10 VE System
- 126 Floppy Disk Drive Cable
- 126 EIDE Device Cables (Installed and Optional)
- 127 Internal-Access Device SCSI Cable
- 127 External SCSI Port Cable
- 128 Internal/External SCSI Cable
- 128 Internal/External SCSI Cable (Zx10 VE)
- 129 Power Supply and Cables
- 129 300 Watt Power Supply
- 131 400 Watt Power Supply
- 133 Cooling Fans
- 134 Hardware Monitoring and Power Management
- 134 System Configuration Summary
- 136 System Specifications
- 137 Setting Your Work Habits
- 137 Getting Started
- 138 Wrists
- 138 Head and Eyes
- 139 Setting Your Environment
- 140 Reducing the Risk of Injury
- 140 Changing Posture
- 140 Taking Rest Breaks
- 141 Taking Care of Your Body
- 141 Getting Help