- Computers & electronics
- Computer components
- System components
- Server/workstation motherboards
- User manual
![](http://s3.manualzz.com/store/data/032423228_1-2071a470cb6531f2f228a83a5c24ab03-128x128.png)
advertisement
![Silicon Graphics® Zx10 Visual Workstation Owner`s Guide | Manualzz Silicon Graphics® Zx10 Visual Workstation Owner`s Guide | Manualzz](http://s3.manualzz.com/store/data/032423228_1-2071a470cb6531f2f228a83a5c24ab03-360x466.png)
9: Servicing the System
Warning:
The system is always on when connected to AC power. Before performing this task, disconnect the system’s power cord from its AC power outlet.
1.
If replacing a DIMM, press the DIMM socket release tabs outward, away from each other; then grasp the top edge of the DIMM and pull it out of the socket.
2. Remove the new DIMM from its antistatic package. Verify the DIMM has gold-plated fingers that match the gold-plated socket contacts, and the slot keys on the DIMM match the slot keys in the DIMM socket.
3. Orient the DIMM so that the notches match the keys in the socket.
4. Push gently straight down until the release tabs snap into place.
5. Restart the system for the BIOS to detect the new memory.
For more information on DIMMs, DIMM sockets, and system memory configurations, see the System Board Guide.
Processor Bus Terminator
On a system with only one processor, a processor bus terminator occupies the other processor slot on the system board. This module ensures proper termination for the processor bus; without it, the system will not function. When you add a second processor, you must remove this module and replace it with the new processor.
Warning:
The system is always on when connected to AC power. Before performing this task, disconnect the system’s power cord from its AC power outlet.
To remove the processor bus terminator:
Carefully pull the terminator card out of the processor slot.
For more information on the processor bus terminator, see the System Board Guide.
106 007-4327-002
advertisement
Related manuals
advertisement
Table of contents
- 21 Unpacking the System
- 22 Placing System Components
- 22 Connecting System Components
- 25 Locating Expansion Cards
- 26 Connecting External SCSI Devices
- 28 Connecting to AC Power
- 29 Starting the System
- 30 What’s Next?
- 31 Preparing for Setup
- 33 Going Through Setup
- 35 Finishing Software Setup
- 36 Installing the Network Controller Driver
- 36 Creating an Emergency Repair Disk
- 36 Installing Driver Software
- 37 Installing QFE Software
- 37 What’s Next?
- 39 Configuring the Video Display
- 39 Resetting the Video Display Resolution
- 40 Changing the Default Video Display Driver
- 40 Correcting Initial Video Display Problems
- 41 Configuring System Audio
- 41 Configuring Networking
- 42 Configuring Peripheral Devices
- 42 Changing Drive Letters
- 43 Changing Virtual Memory Settings
- 44 Configuring the SCSI Controller
- 44 Creating or Updating an Emergency Repair Disk
- 45 Configuring the BIOS
- 45 What’s Next?
- 47 Opening and Closing the Door
- 48 Controlling System Power
- 50 Reading System LEDs
- 52 Using Automatic Shutdown
- 53 Starting and Stopping the Operating System
- 54 Observing Operating Precautions
- 54 Using the Keyboard
- 56 Using the Mouse
- 58 Using the Floppy Disk Drive
- 58 Using the CD-ROM Drive
- 59 Using System Management Software
- 59 Learning About the Operating System
- 60 Using Hardware Security Features
- 60 Cleaning System Components
- 61 Getting Started
- 62 System Power
- 62 System Boot
- 66 Video
- 66 Audio
- 67 Network
- 67 Peripheral Drive Errors
- 68 Miscellaneous Hardware
- 71 Before You Begin
- 71 Finding Driver Software
- 72 Installing the Operating System
- 73 Updating the Operating System
- 75 Before You Begin
- 76 Avoiding Electrostatic Discharge
- 76 Removing and Replacing Side Panels
- 78 Removing and Replacing the Faceplate
- 79 System Components
- 81 Before You Begin
- 82 Adding Expansion Cards
- 83 Identifying Expansion Card Slots
- 84 Installing an Expansion Card
- 85 Assigning System Resources
- 85 Disabling On-Board Controllers
- 86 Adding External SCSI Peripheral Devices
- 86 Choosing SCSI Cables
- 87 Choosing SCSI IDs
- 87 Terminating SCSI Devices
- 88 Connecting SCSI Devices
- 89 Changing SCSI Controller or Device Settings
- 89 Adding Internal Peripheral Devices
- 92 Adding Memory
- 92 Upgrading Processors
- 93 Before You Begin
- 94 Floppy Disk Drive
- 95 Front-Access Peripheral Device
- 99 Internal-Access Peripheral Device
- 102 Expansion Card
- 105 Memory Module
- 106 Processor Bus Terminator
- 107 Processor Module
- 107 Power Supply
- 110 Cooling Fans
- 113 System Board
- 115 CMOS/Clock Lithium Battery
- 116 Chassis Intrusion Alarm Switch
- 117 Power Switch, System LEDs, and Light Pipe
- 121 Functional Diagram
- 122 Internal Peripheral Cabling
- 123 EIDE Cabling
- 123 SCSI Cabling in a Zx10 System
- 124 SCSI Cabling in a Zx10 VE System
- 126 Floppy Disk Drive Cable
- 126 EIDE Device Cables (Installed and Optional)
- 127 Internal-Access Device SCSI Cable
- 127 External SCSI Port Cable
- 128 Internal/External SCSI Cable
- 128 Internal/External SCSI Cable (Zx10 VE)
- 129 Power Supply and Cables
- 129 300 Watt Power Supply
- 131 400 Watt Power Supply
- 133 Cooling Fans
- 134 Hardware Monitoring and Power Management
- 134 System Configuration Summary
- 136 System Specifications
- 137 Setting Your Work Habits
- 137 Getting Started
- 138 Wrists
- 138 Head and Eyes
- 139 Setting Your Environment
- 140 Reducing the Risk of Injury
- 140 Changing Posture
- 140 Taking Rest Breaks
- 141 Taking Care of Your Body
- 141 Getting Help