advertisement
Serial telegram output via RS232, RS422 or RS485.
1. Select mode: Line switched off / on
2. Select time zone see chapter 6.5.27 Time zone selection.
3. Com mode:
1 = send RS 232 (receive is not enabled)
2 = send and receive RS232
3 = send and receive RS485
4 = send RS 422 (receive is not enabled)
4. Baudrate: 300, 600, 1200, 2400, 4800, 9600, 19200, 38400
5. Data bit: 7 or 8
6. Stop bit: 1 or 2
7. Parity: none, even, odd
8. Selecting telegram file changes to the menu “SELECTION OF FILE“
To set the parameters, the line type has to be selected first.
Notice:
Notice:
No flow control available.
The description of the telegram function and the telegram file can be found in Appendix
E Serial Telegrams.
© MOBATIME 27 / 108 801053.02
Selection of the telegram file:
The copy procedure of telegram files is explained in chapter "7.10 Copying Telegram files to the DTS 4148.grandmaster“.
© MOBATIME 28 / 108 801053.02
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- - Safety
- - Maintenance
- - General Information: Introduction
- - Displays
- - Installation
- - Operation
- - Updates
- - Time administration
- 4 Power supply alternatives
- 5 Connection diagrams
- 9 Time zone table
- 12 Alarm list
- 14 Troubleshooting
- 16 Serial Telegrams
- 21 Copyright Notice
- 22 Parameters
- 27 Technical data
- 30 Index
- 32 Connection table (to fill in)
- 6 Safety
- 6 Safety instructions
- 6 Instruction Manual
- 6 Intended Use
- 7 Observe operating safety!
- 7 Consider the installation site!
- 7 compatibility!
- 8 Maintenance
- 8 Troubleshooting: Repairs
- 8 Cleaning
- 8 Disposing
- 9 General Information: Introduction
- 9 Scope of Delivery
- 9 Technical Data
- 9 Device Description in this Manual
- 9 Introduction
- 10 Device types
- 10 DTS Distributed Time System
- 10 MOBA-NMS - Network Management System
- 11 Overview of the main functions
- 12 Device management
- 13 Displays
- 13 LED displays front side
- 13 LED indication back side
- 14 Display
- 15 Installation
- 15 Connections
- 15 Initial configuration
- 15 Firmware
- 15 Basic settings (factory settings)
- 16 Operation
- 16 General
- 16 Telnet
- 17 Menu structure
- 18 MOBA-NMS operation
- 19 Main menu
- 20 Status menu
- 22 Time information and status
- 23 Time source information
- 24 Configuration menu
- 25 Lines
- 25 DCF – output
- 26 DCF / Pulse / Frequency output
- 27 Serial interface
- 29 IRIG / AFNOR / DCF-FSK Output
- 30 NTP slave clocks / time zone server
- 32 SINEC
- 32 Time handling
- 33 Time source
- 34 Time adjustment / Time-keeping
- 35 Redundant operation
- 36 NTP server
- 40 Manual time set / Leap second
- 41 PTP Server
- 43 Alarms
- 43 Alarm relay
- 44 Alarm mask
- 45 E-mail
- 47 SNMP traps
- 49 Alarm input
- 50 General settings
- 51 Network
- 53 Services (network services FTP, telnet, SSH...)
- 55 SNMP V1 / V2c
- 56 SNMP V
- 59 Time zone selection
- 60 Maintenance menu
- 61 Updates
- 61 Updating images with MOBA-NMS
- 61 Updating images with FTP
- 62 Updating images via USB
- 64 FTP connection
- 64 SFTP connection
- 65 SCP connection
- 65 Save Configuration externally
- 66 4148.grandmaster
- 67 Time administration
- 67 Concept of time administration
- 68 Time acceptance
- 68 (DCF or GPS)
- 69 IRIG-B12x source
- 69 Time acceptance from NTP
- 69 NTP as backup
- 69 Time server
- 70 Time accuracy, time-keeping
- 70 Leap second
- 70 NTP Authentication
- 70 NTP symmetric keys
- 71 NTP Autokey
- 73 4148.grandmasters
- 75 General
- 76 Device configuration with SNMP
- 76 DTS subagent SNMP notification
- 76 Startup [dts4148StartUp]
- 76 Shutdown [dts4148Shutdown]
- 77 Status changed [dts4148StatusChanged]
- 77 [dts4148ConfigChanged]
- 78 Alive Notification [dts4148Alive]
- 78 Alarm Notification [dts4148Alarm]
- 79 Power supply alternatives